Search Documents

By R. Dawes, B. R. Davis, T. LeBel, C. Pelow

Settling of copper, lead, and other metals in slags is an important part of overall recovery of metals, both in primary and secondary operations. The impact of slag reduction on settling is not well known. This is important since the cycle time for slag cleaning can be significantly changed with reduction of slag, through a decrease in slag viscosity and growth of metal/sulphide particles. KPM has worked with a number of primary and secondary recyclers to better understand how reduction of slag can improve overall operation. In this presentation, we describe the type of test work and analysis done and how this information can be used to guide improvements in metal recovery from slags. INTRODUCTION Typically, copper smelter slags contain about 1-2% copper, both in the form of copper and copper sulphide beads and dissolved copper oxide in the slag (converter slags are recycled to the smelter). With the average grade of world copper deposits close to 0.7%, it is practical to recovery copper from these slags. This is done routinely by one of two methods. The first method uses slow cooling in large ladles or beds to grow particles of copper sulphide. The slag is then crushed, milled, and floated for copper recovery. The slow cooling promotes precipitation and growing of the sulphide particles from the solution and then, the slag can then be milled to recover the copper through froth flotation. A consideration of this process includes the energy cost related to grinding, the use of water, capital cost for ladles, and the availability of tailing dumps. At the same time, the retreatment of the Cu concentrate produced in the mill will displace fresh concentrate, which ultimately results in a reduction of the throughput. The second method is the so-called “slag cleaning” and is based on the settling of copper and copper sulphides particles dispersed in the slag. This is achieved by decreasing its viscosity by increasing the slag temperature and reducing the iron spinel solid phases (magnetite) that increase the apparent viscosity of the slag. Typically, the reduction does not extend to the reduction of copper, and soluble copper (mainly as oxide) and fine matte particles remain at concentrations typically at or above 0.5% (Cardona et al., 2011; Cardona, 2011). This is an improvement on 20 years ago when slag was sent to dumps at 1% or less (Demetrio et al., 2000).

Jan 1, 2019

By Ali M. Ghazi, Ronald J. Goble, Lowell S. Whiteside

"Geerite (Cu1.6S) is a rhombohedral copper sulphide which occurs naturally in epitactic replacement of sphalerite; cell dimensions closely approximate those of the host sphalerite.Geerite-type structures can be produced by leaching digenite (Cu1.8S) in ferric sulphate solutions. X -ray diffract ion and electron microprobe studies indicate that eight metastable geeritetype structures can be produced, depending upon the concentration of f erric sulphate solution used and the duration of the each. Although compositions cluster on or near values observed for natural phases, optical properties indicate that we are dealing with polymorphs of these phases. Leaching of chalcocite (CU2Sj in dilute f erric sulphate solutions produces similar results. In contrast, leaching of chalcocite in more concentrated solutions seems to produce true analogues of natural minerals.During froth flotation, sphalerite is activated with a monolayer of floatable copper sulphide with the composition, CuS, of the mineral covellite. However, covellite is not significantly more floatable than sphalerite, and has an incompatible structure because of the presence of covalently-bonded atoms of sulphur. Leaching ofdigenite was used to produce a polymorph of covellite with a geerite-type structure, compatible with that of sphalerite. This polymorph has a flotational behaviour similar to copper-activated sphalerite, suggesting that the monolayer has a geerite-type CuS structure. IntroductionIn an ideal close-packed sulphide structure the distance between sulphur layers, D, is equal to 2R 2/3, where R is the radius of the sulphur atoms. In sulphides with covalently-bonded sulphur layers, such as covellite (Fig. I), D will be an average of the number of covalentl y-bonded and close-packed sulphur layers, weighted as to the relative number of each type of layer. Both D and R are spacings which are readily identifiable structurally and on X-ray diffraction patterns. Goblel has shown that for copper-iron sulphides with metal-to-sulphur ratios between 0 and 2 and copper-to-total metal ratio s between 113 and I there are strong correlations between composition and measured D and R distances (Fig. 2). D can be represented by a single empirical equation relating interlayer spacing to composition; R must be represented by three equations relating the radius of sulphur atoms to composition. One of these equations (R, in Fig. 2) represents ideal close-packed behaviour, the other two represent sulphur radii greater than (R1) or less than (Rh) the ideal."

Jan 1, 1988

By William A. Napier

The Mantaro Phosphate Property is located ~ 250 km east of Lima, Peru in the Andean altiplano near the city of Huancayo, Junin District. The Mantaro deposit is a mineralized zone of phosphatic rock currently defined by surface outcrops, trenches and drilling extending over a strike length of more than 30 km and a width of more than 5 km covering ~27,700 hectares. Mineralization is exposed as three roughly parallel exposures (?mantos?) trending in a northwest-southeast direction along the Mancaspico syncline. Estimated mineral resources1 contained in Manto 1 of the Property (4% P2O5 cut-off) as of February 21, 2010, are: Measured 5.548 million tonnes @ 10.8% P2O5 Indicated 33.975 million tonnes @ 9.9% P2O5 Measured + Indicated 39.523 million tonnes @ 10.0 % P2O5 Inferred² 376.265 million tonnes @ 9.0% P2O5 1Tonnes rounded to the nearest 1,000 and grade to 1 decimal place. 2Inferred material reported with no cut-off and an assumed grade. There is considerable potential to expand the resource base. Mantos 2 and 3 of the deposit have been geologically mapped and exhibit surface mineralization widths similar to Manto 1. Given that the deposit is of marine sedimentary origin, it is reasonable to infer that comparable grades and depth of mineralization are present within Mantos 2 and 3. Based on this assumption, the potential mineral deposits within Mantos 2 and 3 are estimated to be approximately: Manto 2 425-435 million tonnes @ 9% P2O5 Manto 3 280-290 million tonnes @ 9 % P2O5 These potential quantities and grade are conceptual in nature, there has been insufficient exploration to define a mineral resource and it is uncertain if further exploration will result in these targets being delineated as a mineral resource. However, should such conceptual resources be confirmed by trenching and drilling, the Mantaro Phosphate Property would rank as one of the most significant phosphate deposits in the world.

May 1, 2011

By J. Poplawski

In mineral processing plants, cyclones typically perform the classification duty prior to the downstream recovery process. Particle size distribution of the cyclone overflow is an important parameter and can be viewed as the product of the comminution process. Too coarse of a product will likely have poorly liberated valuable minerals and make recovery difficult. Too fine of a product may represent a missed opportunity to increase plant throughput and/or also result in low recovery due to poor kinetics. “Near-line” particle size measurement instrumentation has been in place for several decades, its availability and low measurement frequency have typically been inadequate for reliable use in automatic control. CiDRA Minerals Processing has developed a novel and robust technology that provides a highly reliable and low maintenance system for “on-line” measurement of the particle size in the overflow of individual cyclones. The system is based around a wetted sensor design with no moving parts and provides a real-time trend of the desired target grind size parameter. The system does not require sampling and associated sample transfer piping that is prone to plugging, thus avoiding high maintenance requirements. Plant data and benefits realized from the latest installations of the CYCLONEtrac PST will be presented. INTRODUCTION Impact-based real-time hydrocyclone particle size measurement Acoustic impact-based particle size tracking is a unique method for measuring and controlling the particle size in cyclone overflow streams. The implementation of this technology is centered upon a sensor probe that is inserted into the overflow slurry stream via a two-inch (50 mm) hole in the overflow pipe (Figure 1). Particles within the slurry stream impact the surface of the probe generating travelling stress waves within the probe. A sensor converts these travelling stress waves into an electrical signal and proprietary signal processing techniques convert these signals into a particle size measurement that is output every four seconds. The sensor is constantly in contact with many particles in the slurry stream, thus obtaining information from orders of magnitude more particles than traditional sample-based technologies. The sensor has no impact on cyclone performance because it is located downstream of the hydrocyclone and the presence of an air core ensures there is no change in the back pressure seen by the hydrocyclone.

Jan 1, 2019

By Robert D. Brown

"The Conservative Government 's budget proposals brought forward on December 11, 1979 have been withdrawn, but they are far from dead. On the contrary, a number of those budget proposals, especially the ones which would close loopholes and result in other technical changes being made to the Income Tax Act, should be considered to be alive and well.It is not unreasonable to expect the next government, of whatever political persuasion, to reintroduce many of these technical changes in the next federal budget. For that reason, last December's budget may have offered an interesting preview of what the mining industry and other taxpayers can expect in 1980. It is quite possible that some of these changes may be effective as of the original dates announced in the withdrawn budget proposals.This month, ""Tax Notes"" reviews the main pro visions of Mr. Crosbie's December, 1979 budget, with a primary focus on the changes that would have affected the resource sector.It must be emphasized that all of the budget proposals discussed herein have been withdrawn, that none of them are law and that any actual changes in our tax rules will have to be dealt with by the new Parliament that will be assembled following the February 18 election. December 1979budget withdrawnThe federal budget proposals brought forward by Finance Minister John Crosbie on December II, 1979 were withdrawn as a result of the defeat of the Conservative Government on a motion of non-confidence in the House of Commons on December 13. However, it appears quite possible that at least some of the proposals may be introduced into Parliament at a future date, possibly with retroactive effect.In a press release issued by the Department of Finance, Finance Minister John Crosbie stated that if the Conservative Government is returned to power, it will reintroduce all of the measures contained in his December II budget.Mr. Crosbie stated that all of the income tax measures contained in the budget would be reintroduced, effective on the dates indicated in the Notice of Ways and Means Motion tabled on December II. Some of the more important measures in December II budget, and their effective dates as indicated in the Notice of Ways and Means Motion, are discussed below.The December budget had also introduced or increased excise taxes or duties on gasoline, wines, cosmetics and photofinishing. If the Conservative party is re-elected, these measures will be reintroduced with prospective effect (i.e . effective as of new dates to be announced in the new budget)."

Jan 1, 1980

By X. -G. Chen, A. M. Nabawy

A novel manufacturing technique for Al-TiB2 nanocomposites has been developed, in which TiB2 nanoparticles were incorporated into liquid aluminum under mechanical stirring and in the presence of a K2ZrF6 flux-wetting agent. The microstructure of the Al-TiB2 nanocomposites was studied using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The microhardness test was conducted to investigate the strengthening effect of TiB2 on the aluminum matrix. The TiB2 nanoparticles were successfully incorporated and dispersed into the aluminum melt in the presence of the K2ZrF6 flux during mechanical stirring. In the as-cast microstructure, most nanoparticles segregated in the interdendritic regions as a result of particle redistribution during solidification. The addition of 2, 5 and 10 wt% TiB2 nanoparticles increased the composite hardness by 60, 90 and 150% respectively when compared to commercial purity aluminum, indicating that the TiB2 nanoparticles imposed a significant strengthening effect on the aluminum matrix. The role of K2ZrF6 flux agent on the incorporation of nanoparticles into aluminum melt was discussed.

Jan 1, 2014

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The use of large AG/SAG mills in the mineral industry has been on the rise recently due to a significant reduction in the capital and operating costs for achieving significant increases in plant throughputs. The major reason for downtimes in these mills is the time taken for the replacement of broken or worn liners. This loss of “availability” of these units has a significant impact on the productivity of these plant operations. The ability to predict liner life time and its evolving shape could help to optimize these comminution operations. In the past decades, various models have been proposed to estimate liner wear rate, but because of their empirical nature they could only be used within certain limited operating conditions. In this research, a phenomenological model which could predict the liner wear rate was proposed and tested. This model considers parameters such as; operating conditions, liner hardness, pressure on the lifter, and, relative velocity of particles and mill shell. Data from industrially measured liner profiles were taken during the liner life time at the Sarcheshmeh and the Gol-E-Ghohar SAG mills to provide a solid base to calibrate and validate the model. The comparison of the model predictions with the actual measurements of the liner wear rate showed that the results were in a good agreement at both, the Sarcheshmeh (R2=0.94), and the Gol-E-Ghohar (R2=0.97) concentrators.INTRODUCTIONAG/SAG mills are one of the most important technologies in the mineral processing industry in the recent decades. The “Availability” of these units in a plant operation is one of the most important economic parameter for evaluating their performance. The major reason for the downtime of these mills affecting their “availability”, is the time required to change worn or broken liners (Yahyaei, Banisi, & Hadizadeh, 2009; Maleki-Moghaddam, Yahyaei, & Banisi, 2012). The knowledge about the magnitude and profile of liner wear not only enables more accurate liner life estimation to prevent unwanted interruptions of the SAG milling in mineral processing plants and more strategically plan the scheduled mill outages for liner changes. It also could provide key information needed to select an appropriate liner design (Yahyaei et al., 2009; Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010a)."

Jan 1, 2016

By Jose R. Hernandez-Aguilar

"This paper revisits data from previous studies (Hernandez-Aguilar, 2010, 2011) to better understand the link between metallurgical performance and bubble size (Db) in the collection (pulp) zone of full-scale flotation systems. To obtain conclusive evidence exclusively related to the collection zone, the experiments were designed in those studies to control both the bubble generation method and the influence of the froth zone on the overall metallurgical performance in industrial and pilot-scale flotation columns. The results showed that generating small (1 mm) bubbles had a significantly higher beneficial effect on the recovery of coarse (> 75 µm) particles compared to the effect on fine (< 16 µm) particles. It was observed that, under certain practical conditions, the recovery of liberated coarse particles was close to zero, but could be recovered almost completely by reducing bubble size. The evidence revealed an apparent inconsistency of the so-called “k–PSb” model: at constant froth recovery, increasing Sb did not always result in higher recovery, as the model predicts. Overall, the evidence showed that it was not the Sb but the bubble size that proved to be a more reliable link to metallurgical performance. Only under highly suboptimal bubble size conditions (Db = 3 mm) did the froth zone seem to play a role, possibly reflecting an effect of pulp-zone bubble size on froth stability. However, for the most part, both the bubble generation method and the froth zone played inconsequential roles. An empirical model that better describes the kinetics of particle collection is proposed.INTRODUCTIONStudies showing the link between metallurgical performance and the interactions of bubbles and particles in the collection (pulp) zone of industrial flotation systems are scarce. A common belief among a number of mineral processing practitioners considers that “small” bubbles are favourable to recover “small” particles and that, conversely, “larger” bubbles are more efficient at floating “coarse” particles. However, perceptions like this are often substantiated by anecdotal evidence rather than by rigorous data analysis. What is the optimum bubble size for a particular case, how operating conditions can be adjusted to control a target bubble size, and whether the bubble size needs to be changed in the first place to optimize the operation of a flotation plant are questions that usually remain without solid answers.The studies reported by Hernandez-Aguilar (2010, 2011) were, in part, performed to test the effect of bubble size on flotation response and, thus, help address some of the above questions. The focus of the studies was to optimize the metallurgical grade-recovery performance of the Cu-Mo separation plant at Teck’s Highland Valley Copper mine (HVC). The outcome was compelling and significantly valuable: consolidated production data showed that in 2008 – the year when the recommendations from the studies started to be implemented – the Mo plant recovery was 89%, and gradually increased to 92% and 94% in 2009 and 2010, respectively, along with an increase in Mo concentrate grade. (Note: these production figures were not included in the publications quoted above; however, they were shown during an oral presentation at the 43rd Annual Meeting of the Canadian Mineral Processors in 2011.)"

Jan 1, 2016

By M. A. Golozar

Partially stabilized zirconia (PSZ) has been proven to be an excellent candidate as a thermal barrier coating (TBC) for hot sections in, for instance, heat or internal engines and gas turbine parts. The main functions of these coatings are reduction of heat losses, reduction of fuel consumption, increasing efficiency, and extending durability and life. One of the main problems involved is wear behavior in the development of such coatings for these applications. Using air plasma spraying (APS) technique, conventional and nanostructured 8 wt % yttria partially stabilized zirconia (Y-PSZ) coatings were deposited on austenitic stainless steel (AISI 304) disc-shaped substrates. The coated substrates were subjected to pin-on-disc wear tests, using 10 mm silicon nitride and zirconia balls as the pin. The coefficient of friction was recorded in real time. The weight loss of coated substrates was measured. Coatings were characterized before and after being subjected to wear testing by various techniques including optical microscopy, scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDX) and X-ray diffraction (XRD). Effects of various experimental parameters such as wear distance, test temperature, and counterface material were also investigated. Results obtained revealed that, regardless of experimental conditions applied, the nanostructured zirconia coating shows better wear and tribological properties than those of the conventional one.

Jan 1, 2005

By M. Saghaeian, R. Hejazi, Sheikhzadeh. V., A. Abazarpoor

"The morphology of iron ore concentrate particles is known to influence several properties of iron ore pellets, including drop number, compression strength, and reduction properties. This study aimed to determine why grinding methods and particle morphology influence green pellet properties. Particle morphology can be directly related to the grinding method: ball mill (BM) or high pressure grinding roll (HPGR). In this research, two iron ore concentrates, namely Gol-e-gohar and Ardakan, were ground by a BM and HPGR to produce a suitable Blaine value for pelletizing (nearly 1,900 cm2/g). Morphological features of particles were subsequently investigated by sieving and cyclone sizing for particle size distribution, the Brunauer-Emmett-Teller (BET) and Blaine methods for specific surface area (SSA) and scanning electron microscopy (SEM) for the evaluation of shape descriptors. It was concluded that HPGR resulted in generating a greater proportion of fine particles compared to ball milling. The BET results showed that the SSA of HPGR pellet feed was higher than that from the BM due to a greater proportion of cracks, indents and bulges and the creation of new fracture surfaces. SEM images processed by ImageJ software indicated that particles ground by the BM tended to be more rounded and less elongated than HPGR particles because of the breakage model of each method. To show the effect of morphology on the green pellet quality, green pelletizing was performed in a pilot pelletizing disc. The HPGR pellet feed had a higher drop number in comparison to the BM pellet feed, due to the angular and rough shape of the particles.INTRODUCTIONThe demand for fine or ultra-fine particles as feed material for ceramics, composite materials, and mineral processing is on the rise (Kotake, Kuboki, Kiya, & Kanda, 2011). The final concentrate of iron ore processing plants (filter cake) has a size range roughly between 0 and 300 µm, depending on the liberation of Fe containing particles (Meyer, 1980). In general, to produce a suitable pellet feed of appropriate quality, Blaine numbers of 1800–2000 cm2/g should be achieved (Van der meer, 2015)."

Jan 1, 2016

By J. C. Farge, G. G. Jacox

"The effect of composition and process variables on the properties of Marmet and modified Ni-Hard slugs will be discussed. The effect of shape on the over-all performance of grinding media and its relationship to the end product has been investigated and these results will be reviewed. The cost effectiveness of slugs versus balls has been well documented under various operating conditions and this will be presented in detail. IntroductionThe selection of grinding media is based on the cost-to-wear ratio combined with the consideration that it must stand repeated impacts without breaking. The specific consumption of grinding balls and slugs depend s primarily on their microstructure, which, in turn, is controlled by chemical composition and by the processing condition s to which they are subjected during manufacture.The first part of the paper deals with the optimization of alloy content to produce cast iron slugs with microstructures consisting essentially of marten site and carbide and with hardnesses of 650 B.H.N. and higher. The second part deals with the use of cast iron slugs to replace forged steel balls in milling operations. Tests indicate that the shape of the media has little if any effect on results and that the hardness and microstructure of grinding media will determine its relative performance. Where price is equal under similar milling conditions, the cost effectiveness of cast iron slugs is superior to that of forged steel balls.In order to understand the role of alloying elements in cast irons, it is judicious to consider the microstructural changes which occur during solidification and subsequent cooling, particularly from above the eutectoid temperature. Solidification starts with the formation and growth of dendrites of austenite. As temperature decreases, an eutectic nucleates and grows between the primary austenite dendrites. Immediately after solidification, the structure consists of proeutectic austenite and of the eutectic of primary carbides and austenite. On cooling to room temperature, austenite can be retained or transformed to pearlite, bainite, martensite or mixtures thereof. It is necessary to prevent decomposition of austenite into pearlite by adjusting the alloy content. For best abrasion resistance, the microstructure at room temperature should consist essentially of martensite and carbide. These types of irons are known as ""martensitic irons "". Depending on the carbon content of the austenite and cooling rate, "" as-cast"" martensitic irons will contain different proportions of martensite and retained austenite. The more carbon in solution in the austenite, the lower is the temperature at which the martensitic transfoemation takes place. By the time room temperature is reached ., the transformation is seldom complete, and the end product is generally a mixture of martensite and retained austenite."

Jan 1, 1980

By Isabel F. Barton, J. Brent Hiskey

Chalcopyrite (CuFeS2) is the earth’s most abundant copper ore mineral, but is refractory to leaching with sulfates, chlorides, and other common lixiviants and oxidants. This has led to increasing research into alternative lixiviants for recovering Cu from chalcopyrite. Here, we review the leach kinetics of chalcopyrite in glycine, ionic liquids, and methanesulfonic acid, compared to baseline ferric sulfate and ferric chloride. Glycine (CH2NH2COOH) has long been used in applications such as biocatalysis and electroplating, and has recently been examined as a lixiviant for whole ores and concentrates of both copper and gold. It is nontoxic, biodegradable, and capable of strongly complexing Cu2+. Compatible oxidants are peroxide, dissolved oxygen, and ferric sulfate. Chalcopyrite leaching rate in glycine is chemical reaction-controlled, but the effects of grain size and the reaction orders with respect to lixiviant and oxidant concentrations and mass transfer vary. The use of ionic liquids as a leaching agent for chalcopyrite has been extensively investigated in recent years. This system is based primarily on the use of the imidazolium molecule (C3H5N2), which is a planar 5-member ring structure. This lixiviant has been applied to the leaching of chalcopyrite in the form of pure mineral, concentrates, and ores. Kinetics of ionic liquid leaching of chalcopyrite vary substantially depending on the type and concentration of ionic liquid. Methanesulfonic acid (HCH3SO3) is one of the newest lixiviants available in leaching, having only been examined in the last decade. It has been examined as a substitute for sulfuric acid, since it is less corrosive, is biodegradable, and breaks down to carbon dioxide and sulfate over time. The rate of copper leaching from chalcopyrite by methanesulfonic acid is controlled by diffusion and exhibits a strong dependence on oxidant type and concentration. Despite promising reaction rates and total extraction by some of these novel lixiviants, comparison with baseline ferric sulfate and ferric chloride systems makes it doubtful that any will be commercially viable in the near term. Only at very high reagent concentrations and temperatures, and/or very fine grain size, did any of the systems perform comparably to the much cheaper ferric chloride at extracting Cu from chalcopyrite. Most had similar overall reaction rates and total extraction to ferric sulfate, which is relatively common and cheap. However, the leaching kinetics of these novel lixiviants offer valuable insight into the dissolution behavior of chalcopyrite in various systems.

Jan 1, 2019

By M. Hozayen, E. S. Radwan, P. A. Nawrocki, A. Jebbouri

"A major geomechanical study was conducted for one of the UAE onshore oil fields with the purpose of studying reservoir rock properties and stress distribution, based on which a 3D coupled reservoir geomechanical model was built. This model was later used for wellbore stability analysis and for analyzing the effect of fractures on future reservoir production performance, including fracture deformation and permeability evolution occurring due to reservoir depletion and resulting changes in local stress field. The subject of this study was a complex fractured Upper Cretaceous carbonate reservoir characterized by high degree of heterogeneity, both vertically and laterally. Wellbore instability related drilling problems were encountered while drilling the wells in this field. The problems were mainly in drilling the horizontal wells, including breakouts and mud losses. Experimental results of laboratory tests are summarized in this paper whereas wellbore stability analysis and formulation of a 3D geomechanical model that was built for that purpose is summarized in a sister paper (Part II).A suite of tests reported includes tensile strength, uniaxial and triaxial compression and permeability under stress at simulated reservoir conditions. All tested rocks have been grouped into twelve test units and reservoir geology, rock types and challenges related to designing a viable sampling and testing program for a big reservoir are discussed first followed by sample selection criteria and details of the testing program. All test units showed brittle behavior at zero confinement and some samples showed similar behavior at low confining stresses. With confining stress increase, the behavior gradually turned to plastic but some samples showed features of ductile behavior even at low confinement.Obtained experimental data have been summarized in the form of strength criteria and correlations. The Mohr-Coulomb strength equations were obtained for each test unit and also for the averaged values. It was noticed that triaxial compressive strength (TCS) increases with decreasing porosity or increasing density but their influence on TCS is getting smaller with confining pressure increase. Good correlation of porosity and density with Young’s modulus, Poisson’s ratio, unconfined compressive strength (UCS), friction angle, cohesion and tensile strength has been noticed and there was an increasing trend between the confining pressure and TCS. Rock type (mud or grain supported) was not influencing the TCS as much as porosity and density and the two lithologies encountered affected TCS approximately in the same way. These results and correlations are summarized and explained in this paper. They were further used in the numerical modelling part (Part II) of this paper, Hozayen et al. (2015). It is also concluded that rock lithology is not a decisive factor and mechanical properties of tested rocks should be rather considered dependent on porosity and permeability. This helped greatly in reducing the number of tests that had to be performed."

Jan 1, 2015

By J. L. Luo, D. G. Ivey, A. H. Adeleke

Double-edge-notched flat tensile samples of X70 steel were used for both slow strain-rate testing (SSRT) and cyclic loading testing with the notch located in the zone of interest, i.e., the weld metal (WM), base metal (BM) and heat affected zone (HAZ). By using both optical and scanning electron microscopy, the stress corrosion cracking (SCC) behaviour with respect to crack morphology and various forms of microstructure was investigated. In all the samples considered, the mode of failure was predominantly transgranular with cleavage facets around the edges of the fracture surface. The BM, with a bainitic microstructure, had the highest resistance to SCC when compared with the mixed microstructures of acicular ferrite-primary ferrite and acicular ferrite-grain boundary ferrite observed in the WM and HAZ, respectively. The effect of microstructure on stress corrosion cracking behaviour is discussed based on experimental observations.

Jan 1, 2005

By X. X. Wu, Q. Zhang, R. H. Fan, Y. J. Feng, J. D. Liu, P. Z. Zhao

In the present study, AA6016 automotive sheets with different grain size were fabricated through changing fabricating parameters, and the effects of grain size on the bendability were studied by bending test and optical microscopy. The results showed that the sheet with coarse grains exhibited poor bendability, and some micro-cracks were revealed at the surface of the bending samples. While the sheet with fine grains exhibited good bendability, and the bending samples showed smooth surface. Shear bands on the cross section of bending samples were observed. It was found that samples with coarse grains had more shear bands. These shear bands distributed in bundles, which facilitated the formation of continuous neckings and micro-cracks. However samples with fine grains had less shear bands, which distributed uniformly. The decrease of grain size could not only hinder the formation of shear bands, but also improve the homogeneity of its distribution during bending. On the other hand, refining grains could increase the amount of grain boundaries, which impede the propagation of shear bands. Hence the decrease of grain size could hinder the formation of continuous neckings and micro-cracks during bending, resulting in the significant improvement of the bendability.

Jan 1, 2015

By Liu Yulin, Zhao Yi, Tan Qi, Liu Lei

"Hydrotalcite is one kind of layered double hydroxides, and has special crystal chemical characteristics. Due to its good thermal stability, hydrotalcite used as the PVC heat stablier has attracted scientists’ attention. In this study, nano-hydrotalcite was synthesized by the method of mechanochemistry/crystallization, using brucite, Al(OH)3 and Na2CO3 as raw materials, and added into PVC to investigate the effect of hydrotalcite on thermal stability of composites. The synthesis mechanism was suggested by virtue of XRD, FE-SEM, FT-IR. It has been indicated that at the first of dry milling process, the parical sizes of brucite and Al(OH)3 decrease, while specific surface areas of them increase by the action of mechanical force, until produced amorphous particles. In the process of wet milling, metal ions in the amorphous body, which has high surface energy, can easily react with H2O, and produce the precursor of Mg6Al2(OH)18•4.5H2O, which has the same crystal structure as hydrotalcite. Under the hydrothermal condition, anions of OH- in the interlamination of precursor are exchanged by CO32- in the solution and nano-hydrotalcite is generated at last. The thermal stability was characterized by Congo red method. The results have revealed that hydrotalcite is one kind of long-term heat stabilizer, and residual stability time increase with the rise of added hydrotalcite amounts.INTRODUCTIONHydrotalcite, one kind of anionic clays, has been attracted a great interest for researchers because of their unexpected physical and chemical properties. The general formula is Mg6Al2(OH)16CO3·4H2O, where Mg2+ and Al3+ occupy octahedral positions in the brucite-like layers, and CO32- is an interlayer anion (Hoyo, 2007). Hydrotalcite is widely used in the fields of chemical engineering, materials engineering, environmental protection, medicine, and so forth, owing to its unique capability of adsorbability, ion exchange and thermal stability (Rozov, Berner, & Taviot-Gueho, 2010; Iwasaki, Yoshii, & Nakamura, 2012; Ay, Zümreoglu-Karan, & Temel, 2011; Cavani, Trifiro, & Vaccari, 1991; Li & Duan, 2005; Lin, Wang, & Evans, 2006). As a result, the study on synthesis and application of hydrotalcite has received considerable attentions."

Jan 1, 2016

By A. R. Sheik, A. A. Baba, M. K. Ghosh, K. Sanjay, R. B. Bale, A. G. F. Alabi, F. A. Adekola, L. Ibrahim

"This paper studies the characterization and dissolution of a Nigerian pyrolusite ore, reporting the results of ore physicochemical analyses and detailed ore characterization before and after leaching at optimal conditions. Ore dissolution rate increased proportional to acid concentration and temperature, but decreased with ore particle size. In a 4 M H2SO4 solution at 80°C with a particle size of –90+75 µm and moderate agitation, ore dissolution rate reached 78.7%. Unleached residue produced under optimal leaching conditions consisted of silica with admixtures of cristobalite and stishovite. The calculated activation energy supported the proposed diffusion control mechanism for the process.RÉSUMÉ Le présent article étudie la caractérisation et la dissolution d’un minerai de pyrolusite du Nigeria, il donne les résultats des analyses physicochimiques du minerai et de la caractérisation détaillée du minerai avant et après la lixiviation sous des conditions optimales. Le taux de dissolution du minerai augmentait proportionnellement à la concentration de l’acide mais décroissait avec la taille des particules. Dans une solution 4 M H2SO4 à 80 °C, avec une granulométrie de –90+75 µm et une agitation modérée, le taux de dissolution du minerai a atteint 78,7 %. Les résidus produits sous des conditions optimales de lixiviation étaient constitués de silice avec un mélange de cristobalite et de stishovite. L’énergie calculée d’activation supportait le mécanisme de contrôle de la diffusion proposé pour le procédé."

Jan 1, 2016

By M. C. Ethier, A. L. Laramie

"The Granisle and Bell Copper mines were officially put into production in 1966 and 1972, respectively. The Granisle Mine was purchased in late 1979by Noranda and the two operations were amalgamated as one division. Both mines were closed in 1982after sustaining heavy financial losses during a period of low copper prices beginning in 1981.This paper describes the resumption of operations at the Bell Mine in 1985 after its shutdown period of three years and the dramatic and sustained improvements in productivity and efficiency realized as a result of a commitment by employees and management to the application of Participative Management and Employee Involvement principles. After a general description of the effects of such a philosophy on the operation as a whole, and a comparison to the operation&apos;s last full year as a producer, it deals with the practice of this philosophy in the maintenance department at the Bell Mine and the superb results realized.IntroductionThe Bell Copper deposit was discovered in 1963 and came onstream as a 10000 ton s per day open pit mine in the fall of 1972. Identified reserves at that time were 46 million tons of ore containing 0.50% copper. The mine shared facilities of the townsite of Granisle with the nearby Zapata-Granby mine which had established the community six years earlier.Because of easy grinding ore and improvements to milling circuits, Bell&apos;s throughput rate was increased to 17 000 tons per day by the late 1970s. In the open pit, improvements resulted in mining of additional reserves with higher stripping ratios. At startup, a half ton o f waste was mined for every ton of ore processed.By the end of 1982, with 48.2 million tons already mined, the Bell Mine had identified additional mineable reserves of 39.4 million tons containing 0.52% Cu.In November 1979 the Granisle Mine was purchased from Zapata-Granby. The two mines, with a total of 700 employees, were operated under common management as the Babine Division until 1982 when low copper price s forced the closure of both for an indefinite period.The outlook for copper prices remained bleak and only 50 people were retained on the payroll to maintain the two plants, most of them working on a part-time schedule.The population of the Village of Granisle dwindled from over 1500 inhabitants to under 500, as people moved away to seek other employment.Prior to the shutdown, the Bell Mine employed 370 people and pit extraction averaged nearly 50000 tons per day of which 16000 tons was mill feed, and the remainder waste. Total cost to produce a pound of copper was C$1.36 in 1982."

Jan 1, 1990

By D. Thibault, A. Akhiate, M. Brochu, E. Braud

Cast martensitic stainless steels, 13%Cr-4%Ni, having carbon contents between 0.018 wt% and 0.067 wt% were normalized, air quenched, and tempered at two different temperatures (550°C and 610°C). Their microstructures were characterized by optical microscopy and X-ray diffraction (XRD). Macro and microhardness, tensile strengths, and impact resistance were quantified for each material and condition. Results show that the prior-austenite grain size is constant through the materials but the percentage of reformed austenite, contained in the martensitic matrix, depends strongly on the material chemistry and on the tempering temperature and on its duration. It is observed that, independently of tempering conditions, an increase in carbon content increases the material hardness and tensile strengths, whereas the elongation remains constant. In contrast, the results of Charpy type impact toughness tests show a different trend. The material containing the average carbon content (0.034 wt%) is significantly tougher than the two other alloys. Surprisingly, the toughness of the steel containing 0.034 wt% carbon was found independent of the reformed austenite content. It is thus concluded that carbon and reformed austenite contents are not the only parameters affecting the toughness of these steels.

Jan 1, 2014

By Robert B. Parsons

"Effective January 1, 1990, mines in British Columbia are subject to a new provincial mining tax statute, the Mineral Tax Act. Under this Act, mines are subject to a two-tier tax system, with a minimum tax payable on ""net current proceeds"" and a higher tax paid on net income. For many mines, the present value of tax paid under the new rules should be comparable to the amount paid under the old rules. Earlier cash payments could pose difficulties, particularly for smaller mines, but existing producing mines could benefit in the short-term.IntroductionEffective January 1, 1990, British Columbia has replaced the provincial mining tax regime under the Mineral Resources Tax Act with a new system under the Mineral Tax Act. The new rules borrow some ideas from other provinces (New Brunswick&apos;s two-tier concept, and Saskatchewan&apos;s indexed costs) with a view to levying a tax that is fairer to both the producer and the province."

Jan 1, 1990