Search Documents

By P. E. Walker, M. E. Reed, R. C. Sims, B. Snowdon, D. E. Fallas

An advanced Flash Furnace feed system is the key to improving furnace performance. Clyde-WorleyParsons has developed a revolutionary pulseless pneumatic injection feed system technology, capable of delivering a range of benefits to operators of Flash Furnaces. The solution was created by combining the pneumatic conveying and injection knowledge, expertise and technology of Clyde Materials Handling with WorleyParsons' flash furnace process and operating experience. Optimal furnace burner performance requires the feed material to be presented to the burner as a stable, pulseless and accurately controlled flow, distributed evenly around the burner tip circumference. These simple requirements appear obvious, but are extremely difficult to satisfy in industrial environments and are not achieved by conventional feed systems. Our analysis of existing operating furnaces has identified the link between pulses in concentrate feed rate caused by conventional drag chain conveyors and rapid fluctuations measured in the furnace pressure. These fluctuations occur at a timescale close to the reaction shaft residence time and lead to unwanted instability in the primary furnace reaction zone - the flame. Through the use of the solution created by Clyde-WorleyParsons, it is predicted that the much more accurate control of feed rates achieved can lead to substantial improvements in furnace output, increased oxygen efficiency and better control of the composition of furnace liquids, such as matte, blister or slag. All these improvements lead to significant increases in smelter output and efficiency, and deliver high economic value compared to the cost of the feed system. Clyde-WorleyParsons' solutions can be deployed on greenfield sites or retrofitted, and therefore, have the capability to improve feed control at both new and existing smelters. This paper will discuss the field test work undertaken to date, the impact of findings and the ongoing analysis of linkages between instabilities in the various components of conventional feed systems and furnace pressure stability.

Jan 1, 2007

By L Tafaghodi Khajavi, M. Barati

The distribution of phosphorus between solid silicon and iron-silicon melt was determined to investigate the degree of phosphorus removal from silicon by solvent refining with iron-silicon alloys. The distribution coefficient which is the ratio of the mole fraction of phosphorus in solid to that of liquid is as follows: 0.22±0.02 (1310°C), 0.29±0.02 (1260°C) and 0.33±0.02 (1210°C). The removal percentage of phosphorus is: 84.2% (1310°C), 72.5% (1260°C), and 63.7% (1210°C). The average phosphorus content of produced silicon in the proposed solvent refining process would be over two times less than that of the conventional directional solidification. The values of interaction coefficient of phosphorus on iron at different temperatures were obtained as -3460±155 (1310°C), -3595±159 (1260°C) and -3694±119 (1210°C). Self interaction parameter of phosphorus at different temperatures are as follows: 68±4 (1310 ?C), 78±10 (1260 ?C) and 103±19 (1210 ?C). The calculated values for distribution coefficient of phosphorus at infinite dilution are: 0.22±0.00 (1310°C), 0.30±0.00 (1260°C) and 0.34±0.00 (1210 °C).

Jan 1, 2015

By E. Asselin

Electrochemical polarization experiments were conducted on alloy 625 in ammonia solution between 25 and 225°C and the results were compared with those of an oxygen solubility model. Results confirm that corrosion is under oxygen control, Normalized corrosion rates are determined based on the rate of oxygen diffusion to the corroding surface, and the corrosion rate at 200°C (-9.7 µA.cm-2) is roughly 24 times higher than the corrosion rate at 25°C (0.4 nA,cm-2), An oxygen-solubility model for Supercritical Water Oxidation (SCWO) conditions was generated using the Redlich¬Kwong-Soave (RKS) equation of state, Results of the model confirm many of the experimental observations from SCWO reactors which suggest that corrosion is at a maximum at temperatures just short of the critical point, The RKS/oxygen diffusion model predicts that the corrosion rate at 365° C is ?85 times higher than the corrosion rate at 25' C. Given that a normalized corrosion rate is obtained, this type of model could be useful for selection of SCWO reactor materials.

Jan 1, 2005

By Afshin Sadri, Wai Lai Ying, Brycklin Wilson, Zoe Coull

"Although there have been great steps forward to integrate corrosion engineering into operations, there is still an underlying tendency for maintenance tasks to be performed in a reactive manner. This is especially true when strategies focus on lagging indicators such as visual inspections, RCA (root-cause analysis), and FMECA (failure mode, effects and criticality analysis). This trend to “reactive maintenance” can be avoided by utilizing more inspection and monitoring methods to identify leading indicators of failures. Prevention is generally less costly than repairs; moreover, when paired with appropriate monitoring techniques, intervention of corrosion protection can be more effectively timed and based on more accurate data. Hatch asset reliability studies show nearly 80% of defects are introduced through operations and maintenance. Therefore, proactive corrosion management can provide the necessary feedback to optimize operations and maintenance strategies preventing costly corrosion losses. Understanding corrosion risks gives a clear picture of the benefits of a proactive approach to asset performance. Monitoring techniques (Non-Destructive Testing, field testing, sampling, etc.) by nature are a more effective means of improving maintenance efforts and preventing corrosion losses than other methods (RCA, FMECA). This paper will outline the importance of proactive corrosion management and demonstrate its benefits through industry examples.INTRODUCTION Over the past few decades, with the growth of technology and awareness of sustainable development many studies have shown the benefits of a proactive approach to maintenance strategies. However, in practice there is still an underlying tendency for maintenance tasks to be performed in a “reactive manner”. This is especially true when strategies focus on lagging indicators such as visual inspections, RCA (root-cause analysis), and FMECA (failure mode, effects and criticality analysis). This trend to “reactive maintenance” can be avoided by utilizing more inspection and monitoring methods to identify defects and leading indicators to failures."

Jan 1, 2017

By V. Polotski

Initiated and financed by the Canadian Space Agency, Micro-Rover Platform with Tooling Arm (MRPTA) project has targeted the development of a robotic system with remote control and autonomous navigation capabilities for testing a large variety of analogous planetary missions. Although developed for planetary exploration, the navigation system is highly suitable to such areas of application as construction and in mining. Autonomous navigation system is capable of moving the platform to predefined position(s)/orientation(s) while continuously mapping the terrain, assessing its traversability and choosing most appropriate path to follow. Designed according to the JAUS (Joint Architecture for Unmanned Systems) framework, the system consists of several interconnected components. Following components are of particular importance: Pose Estimator (PE), Terrain Evaluator (TE), Map Manager (MP), and Path Planner (PP). The PE uses a minimal sensor configuration consisting of an azimuth gyroscope, inclinometer and wheel odometry. The PE provides reliable pose estimates in spite of pronounced slippage by employing extensive use of fused data. The TE uses a nodding laser scanner which continuously sweeps the area in front of the platform and constructs a ?traversability grid? (TG) of the surrounding area. Multiple TGs are constantly constructed along the platform motion path are combined into a terrain map maintained by the MP. The PP uses this map to compute a motion path Obtained path is executed by the motion controller and remains current until it is contradicted by the most recent map ? at which point it is re-planned. This paper addresses integration issues, lessons learned and also outlines the possible applications for construction and mining.

Aug 1, 2013

By D. Bai, F. Hamad, S. Abraham

For the integrity of welded structures such as pipelines, the toughness of the heat-affected zones (HAZ) is an important property. This property is often specified in terms of Charpy V-notch (CVN) impact toughness and determined by the standard test method. An experimental study has been conducted in an industrial laboratory to measure the impact toughness of the coarse grain heat-affected zones (CGHAZ) of an X80 line pipe material. The field girth welding conditions in terms of heat input were simulated, together with special edge preparation to improve the targeted testing of the CGHAZ. The effect of toughness of the neighboring regions, in particular the weld metal, on measured impact toughness of the CGHAZ was investigated. The fracture paths of the CVN tested samples were examined by both optical and scanning electron microscopy. The deviation of segments of the fracture path into the weld metal was found to have a significant effect on the measured impact toughness of the CGHAZ.

Jan 1, 2005

By L. Dorador

"In block caving projects, the rock mass fragmentation process plays a controlling role in the design and success of the operation. Poorly understood, however, is the secondary fragmentation that occurs as blocks of caved ore move through the draw column and interact with one another. The initial size of these blocks can be considerable, as can their strength and stiffness as the presence of non-persistent joints and veining will be variable. Intuitively, more planes of weakness within the blocks should facilitate early fragmentation, but this assumption could depend on additional factors such as contact type between adjacent blocks and loads imposed through varying heights of the draw column. This paper reports the findings from a laboratory investigation examining the role of block strength and planes of weakness on secondary fragmentation. Testing was carried out on small-scale concrete cubes of uniform size, with and without embedded planes of weakness. The results obtained demonstrate the significance of veining and other planes of weakness on secondary fragmentation under one-dimensional compression, and allow for the development and constraint of empirical guidelines.INTRODUCTIONThe fragmentation process during block caving involves the initial (primary) fragmentation of rock in the cave back through stress-induced fracturing, release and fall of individual blocks onto the broken ore muck pile. This is followed by secondary fragmentation involving splitting and rounding of blocks as they move downwards through the draw column towards the draw point. The degree of secondary fragmentation achieved involves many variables related to the mechanical properties of the rock blocks as well as different operational factors. With respect to the block properties, the presence of planes of weakness in the form of veining and non-persistent joints is a topic of special interest given the significant influence it potentially has on the overall fragmentation process. However, the inherent heterogeneity and variable size of individual blocks generated from the cave back makes it difficult to develop any empirical relationships relating secondary fragmentation to compressive loading based on insitu observations and mine data. More preferable would be to keep constant block parameters, such as shape (aspect ratio and angularity) and size, through controlled laboratory testing. This work presents an efficient technique to fabricate concrete cubes in order to keep constant different block properties. These are then tested under one-dimensional compressive loading. The objective of these tests is to emulate a tight packing condition of single blocks such as that which would occur when the air gap between the cave back and broken ore in the draw column is small. When the air gap is small, detached blocks are unable to fall and rotate but instead maintain a very tidy arrangement with minimal voids left between adjacent blocks."

Jan 1, 2015

By Robert Drummond

Away back in the eighties of the last century, when Sir Charles, then Doctor, Tupper, was not only a prominent but a dominant figure in the political life of Nova Scotia, his opponents brought the railing accusation against him that he was the foremost of egotists because of his frequent use of the personal pronoun. I heard Tupper speak and had no sympathy with the railers, because I could not well see how the pronoun could be dispensed with without laying himself open to a charge of affectation. I shall make reference in what follows to incidents in which I have taken part, and shall be at no pains to dispense with the pronoun, even though thereby I lay my-self open to the charge of being a pupil of the deceased states-man. EVENTS LEADING UP TO THE ORGANIZATION OF THE PROVINCIAL WORKMEN'S ASSOCIATION The Springhill Mining Company began development work at Springhill in the early seventies of last century. So vigorously was the work prosecuted that in 18 7 4 two slopes, the east and the west, were in active operation, with a considerable. output, the east slope on occasional days producing 800 tons. The President of the Company, the late Senator McFarlane, was a Nova Scotian, the other directors were mainly merchants from St. John, N.B. From the first the enterprise was an .astonishing success, due in the greatest part to its geographical position, and in large part to the untiring vigilance of the directors, a majority of whom visited the collieries at short intervals, thereby keeping the manager, much of the time, on tenter hooks.

Jan 1, 1924

By E. Johansson, T. Siren, K. Kemppainen

"As part of the preparations for the design of an underground repository for radioactive waste at Posiva’s Olkiluoto site on the west coast of Finland, there has been considerable site investigation work. Except the extensive surface based investigations, Posiva started in 2004 the construction of an underground characterisation facility termed the ‘ONKALO’. The ONKALO has now been completely excavated to the anticipated repository depth i.e. -430–450 m. The research conducted in the ONKALO gives further information on the bedrock and groundwater conditions of the final disposal site, as well as on the impact of the construction. The ONKALO provides an excellent opportunity to investigate the rock at tunnel scale, to conduct in-situ testing in rock, to develop excavation and final disposal techniques in realistic conditions. The ONKALO has aided in collecting the data needed, supported by a Preliminary Safety Assessment, for the application of the construction license that was submitted in the end of 2012. The target is to begin disposal operations in 2022. According to current plans, the final disposal would end in 2112 and the repository would be sealed up by 2120. The testing in the ONKALO still continues several years. This paper presents the current characterisation and research activities in the ONKALO. INTRODUCTIONAfter the Finnish Government's favourable policy decision in 2001, Posiva Oy, which is an expert organisation responsible for the final disposal of spent nuclear fuel of the owners in Finland, has focused further investigations at the Olkiluoto site, western Finland (Figure 1) and has started in 2004 the construction of an underground facility termed the ‘ONKALO’. The ONKALO is not a nuclear waste repository, but more than just an underground research laboratory URL – it is an underground rock characterisation facility. The ONKALO has now been completely excavated to the anticipated repository depth i.e. -430–450 m. In addition to facilitating bedrock research, the ONKALO also provides an opportunity to develop excavation techniques and final disposal techniques in realistic conditions. Later, the ONKALO facilities can be put into use when building and using the repository. The construction methods and materials have been selected in order not to jeopardise the long-term safety of the repository site. The findings of the ONKALO and other investigations will provide the knowledge needed for an application, supported by a Preliminary Safety Assessment, to construct a final repository for spent nuclear fuel at the site. Posiva has submitted an application for the construction licence for a disposal facility in the end of 2012. The target is to begin disposal operations in 2022 and the repository would be sealed up by 2120."

Jan 1, 2015

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"Abstract - MEGATEMII airborne electromagnetic data collected over the Iso and New Insco massive sulfide deposits have been modeled using three modeling packages. The EMQ package is a quick inversion tool which indicates that the Iso body is a dipping, plate-like body. The New Insco body is inferred to have a geometry somewhere between a dipping plate and a sphere. The Maxwell package was used to refine the properties of the plate-like body at Iso. The EMIGMA package was able to identify which parts of the New Insco orebody were more conductive. It was observed that the most conductive parts correspond to copper-rich zones and the next most conductive to pyrite-rich zones. The EMIGMA package was also used to show that a thick-prism model might be more appropriate for the New Insco orebody. Gravity modeling constrained by the known geology was successful in identifying the denser sulfide zones. The densest zones appear to be pyrite rich. Magnetic modeling identified diabase dikes. Over New Insco, a small magnetic anomaly was attributed to pyrrhotite-rich sulfides. There was only a weak magnetic anomaly over the Iso body, consistent with the nonmagnetic sulfides logged in the holes drilled at that location. Sommaire - Les données MEGATEMII recueillies au-dessus des dépôts d’Iso et de New Insco ont été interprétées en utilisant trois outils de modélisation différents. L’outil EMQ a été utilisé comme un outil d’inversion rapide suggérant que le dépôt Iso peut être considéré comme une plaque inclinée, et que le dépôt de New Insco se situe quelque part entre une plaque et une sphère. L’outil Maxwell a été utilisé pour raffiner les propriétés du dépôt Iso. L’outil EMIGMA nous a permis d’identifier les différences de conductivité à l’intérieur du dépôt Iso. Il a été observé que la partie la plus conductrice correspond à la zone riche en cuivre, suivie par la zone riche en pyrite. L’outil EMIGMA a aussi permis de montrer qu’un modèle de prisme épais pourrait être plus approprié pour décrire le dépôt New Insco. La modélisation des données gravimétriques, contrainte par la géologie connue, définit bien la zone de sulfures massifs. La zone de pyrite semble être la plus dense. La modélisation des données magnétiques identifie bien les dykes de diabase. Au-dessus du dépôt New Insco, on observe une faible anomalie magnétique correspondant aux sulfures non magnétiques observés dans les carottes de forages à cet endroit."

Jan 1, 2006

By M. Kawata, T. Amano, T. Miyamoto, K. Shibayama

"The High Pressure Acid Leach (HPAL) plant of Taganito HPAL Nickel Corporation (THPAL), located in Taganito, Philippines, with a nameplate capacity of 30,000 Ni-t/year started commercial operation on October 2013. The plant load was smoothly ramped up and it achieved monthly production equivalent to 33,000 Ni-t/year in 2016. Partial improvement of the plant capacity for the achievement of 36,000 Ni-t/year, as evaluated from the current operation progress of each system is planned for 2017. In this paper, aside from presenting the progress of the plant ramp-up, research and development activities such as the reduction of nickel loss and the improvement of filtration capacity which was achieved by particle size control of ZnS precipitates in the Zinc Removal system are also discussed.INTRODUCTION Taganito HPAL Plant Project History of THPAL Taganito HPAL Nickel Corporation (THPAL) was incorporated in August 2008, as a joint venture of three (3) companies, namely Mitsui Corporation with 15% share, Nickel Asia Corporation (NAC) with 10% share and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 75%. Aside from its capital share, NAC’s Taganito Mining Corporation (TMC) supplies the ore for the HPAL plant located in Taganito, Claver, Mindanao, Philippines. The objective of THPAL is to produce 30,000 MT of nickel and 2,600 MT of cobalt as mixed (Ni/Co) sulfide by treating nickel laterite ore in the Philippines and exporting to Japan as raw material for SMM’s Niihama Nickel Refinery (NNR) for the next 30 years. In other words, 1.15 wt% of nickel in ore is refined to 99.99 wt% nickel in electrolytic nickel. The mixed (Ni/Co) sulfide is shipped to NNR and SMM provides the technology and management personnel to THPAL plant as well as sulfuric acid which is the main reagent for HPAL process. Figure 1 shows the location of THPAL and current relationship between the stake holders.The Characteristics of THPAL Plant In terms of plant design, a 2-train system is applied for the HPAL circuit considering the reliability of the process, facility and avoidance of whole plant shutdown due to HPAL troubles. The technical data, operation know-how and improvements gained from the successful operation of Coral Bay Nickel Corporation (CBNC) which was established in April 2002 were reflected in THPAL’s plant design. As for the H2S plant, a more economical design was considered which is different from CBNC."

Jan 1, 2017

By H. R. Hammond, E. Sadar

Cominco is making substantial savings in secondary breaking by replacing dynamite with a new nitrate-based explosive. Compareo with dynamite. the new explosive, known locally as "Fine NCN," is significantly cheaper, more effective and safer to use. It also works better than prilled NCN, which is unsatisfactory for secondary blasting because of inadequate sensitivity, low strength and awkward handling properties. A simple apparatus has been devised for pulverizing prilled NCN to a fineness practical for effective secondary breaking. Blasting systems using cheap detonating cord for initiation have been developed.

Jan 1, 1966

By K. R. Barnard, K. D. Marte, T. V. Gamarano

"The first commercial scale application of CSIRO’s direct solvent extraction (DSX) technology has been in operation at the Boleo project in Mexico since December, 2015. In this application, DSX is a synergistic solvent extraction system consisting of the extractants LIX 63 and Versatic 10 for recovery of cobalt and zinc from a solution background of manganese, magnesium, and calcium. Key operating parameters such as metal extraction, phase disengagement and extractant stability are summarized and discussed in this paper.INTRODUCTION Commissioning of the Boleo processing plant, located on Mexico’s Baja peninsula, began with the copper circuit starting in late 2014, with first copper cathode production achieved in January, 2015. The cobalt and zinc circuits began commissioning in December, 2015 with first zinc sulphate monohydrate (ZSM) and cobalt cathode production achieved in February and April, 2016 respectively. The Boleo project flow sheet and development has been described in detail in previous publications (Dreisinger, et al. 2005; Dreisinger, Baxter, & Molnar, 2006; Dreisinger, et al. 2008; Dreisinger, et al. 2009) and is summarized schematically in Figure 1. Boleo is a mixed oxide/sulphide Cu-Co-Zn-Mn high clay deposit that is processed in a whole ore, atmospheric, oxidative and reductive, sulphuric acid/seawater leach. Copper is recovered as cathode by conventional solvent extraction and electrowinning. Cobalt and zinc are recovered, from a solution background of manganese, magnesium, and calcium, by CSIRO’s synergistic solvent extraction technology Direct Solvent Extraction (DSX). Cobalt and zinc are bulk stripped from the DSX circuit and then further purified by phosphinic acid solvent extraction to produce zinc sulphate monohydrate granules via spray dried granulation and cobalt cathode rounds via divided cell electrowinning."

Jan 1, 2017

By A. McLean, A. Hue, K. Le, Y. D. Yang, P. Wu

While the treatment of relatively inexpensive ferrosilicon alloys is a potential refining route in order to generate solar grade silicon, phosphorus is one of the more difficult impurities to remove by conventional processing. In this project, the use of an electromagnetic levitation technique was used to investigate the dephosphorization of ferrosilicon alloy droplets exposed for various times and temperatures to a hydrogen-argon gas mixture. It was found that approximately 40% of the phosphorus was removed from an 85%Si-15%Fe alloy after 20 minutes exposure at approximately 1673K, to a gas mixture containing 48.5% hydrogen. Further dephosphorization is expected with longer reaction times. The effect of increasing temperature was found to be insignificant, although processing at lower temperatures is not only economically advantageous, it also decreases evaporative silicon losses, thus resulting in a more efficient process.

Jan 1, 2015

By Marc Piard

In a cool mine, tapping high-pressure lines through reducing valves lowers the temperature beyond remedy. It is the writer's suggestion that, for low-pressure work, law-pressure air ,should be generated in a compressor installed underground adjacent to the work, and that the jacket-water of the compressor should be utilised for re-heating purposes. Such a system of compressed air distribution, designed especially for service in cool mines, is described in the following notes. The suggested system includes a three-wire pole line from the sub-station to the opening nearest to the working face, with a cable connection extending to the latter from the openings; an electrical centrifugal unit; a reservoir excavated in the ground; and a distribution line, re-heated by jacket-water. As regards the reservoir, it may be pointed out that in many mines there are blind or abandoned tunnels that could be used for the purpose. The centrifugal type of compressed air machine is a comparatively new departure, and it was formerly considered that such a machine, operating at less than 1,000 kilowatts per unit, would be commercially impracticable. At the present time, however, these machines are being built in Europe for as little as 400 kilowatts per unit, and as much as 110 lb. per sq. inch pressure. One advantage which these centrifugal machines have over other types is that they may be driven by plain induction motors, without the help of special starters-a consideration of the first importance where the electrical regulations are severe.

Jan 1, 1926

By A. D. Dalvi

Economics, Resources, Environment and Technology are the major driving forces in the base metals industry. However, these factors are intertwined and together will propel the industry in the future. The demand for metals has grown with economic expansion, between 2 to 4 % p.a. The current growth cycle has been driven by economic expansion in China where the demand for base metals has risen from - 7 % of the world demand in the 90's to - 25 % of world demand today, and rising. Base metals are commodities and their demand and price are cyclical. Historically metal prices have declined in constant dollars, forcing the industry to reduce costs, increase productivity and increase the scale of operation for economies of scale. Due to resource depletion and capacity expansion the industry is driven to expand its reserve and resource base. However, in the case of sulphide deposits of copper and nickel it appears to be a losing battle. For nickel the laterites represent a vast source at this time. Their development requires development of new technologies to make these resources economic. Emission reduction is being increasingly mandated in most jurisdictions with all governments enacting progressively more stringent regulations. The industry has been responding with technological innovation. With the Kyoto protocol there is a push to reduce energy intensity in metal production. Technological innovation is driven by all the other factors and is leading to novel ways of doing exploration, mining and processing, that would maximize resource delineation and utilization, reduce costs, increase productivity, reduce energy consumption, maximize asset utilization and reduce environmental affects. Development of alternative technologies such as Pressure Acid Leach of laterite for nickel, bio-leaching, heap leaching, SX-EW etc are being adopted to achieve the aims of the industry.

Jan 1, 2005

By G. F. Trainor

The complex ore body at CNRL?s Horizon mine presents some unique challenges in managing ore and waste delivery. With 25m x 25m ore blocks shovels often take bucket loads from multiple blocks to fill one truck load. With CNRL monitoring 22 different qualities per material a precise calculation of the blended quality of ore on the back of each individual truck is essential to meet the daily blend requirements at the plant. Additionally, one of these qualities must be closely monitored and controlled at a singular level as delivery of certain grade and quantities can cause serious disruptions at the plant. The waste material also requires special handling and delivery for its use in dyke construction for tailings impoundment. Shale materials used in the construction contain high levels of saline that must be contained to prevent seepage into ground water. This paper will discuss how the use of Wenco?s survey-grade GNSS system on shovels, its dispatching algorithm, and fleet management applications give CNRL the ability and confidence to control and report on these three issues.

May 1, 2013

By Antonius Prayoga

PT Smelting adopted the Mitsubishi Continuous Technology for its copper smelter plant which has been operating since 1998. Through a series of expansion projects, the plant annual production capacity increased gradually from 200,000 to 300,000 tons of copper. There were no significant modifications for the smelter to reach the 50% additional capacity. It was mostly achieved by intensifying the operation of the furnaces by increasing the oxygen content in the furnaces blowing air. Intensive smelting furnace operation caused shorter campaign life of some furnace refractory, especially the melt zone wall on furnace outlet. During each furnace relining, which is done once every two years, severe wall erosion was found. The worst condition occurred in 2007 when the smelting furnace experienced a melt leak through the eroded wall beneath the bath-line coolers. During the 2008 furnace relining, a modification was performed by installing vertical coolers behind the melt zone wall. Additional vertical coolers were installed during the 2012 furnace relining to extend the coverage area. The modification improved melt zone wall integrity significantly by keeping them safely within the two year campaign life. Recently a modeling study was done to estimate the influences of molten waves on furnace wall erosion. The aim of the study was to predict the impact of blowing parameters, such as blowing air velocity, on the melt wave character and wall erosion.

Jan 1, 2015

By Emilie Williams

Introduction Mouska Mine, Doyon Division site Background and timeline Obstacles to standard paste delivery system Components of Mouska paste system Technical considerations Operational considerations Mouska Mine Underground gold mine 30 km east of Rouyn-Noranda, Quebec Part of Doyon Division, 100% owned by IAMGold Commercial production since 1991 Cumulative production over 850,000 oz Conventional mining until 2009 485 m shaft from surface 560 m internal shaft 500 tpd (ore and waste) Off-site milling Approximately 150 employees

Oct 1, 2010

By Ginger Gibson

As an occupational culture, mining comes with its own set of rules, agendas and values. Yet mines often also operate in the traditional territories of indigenous communities, with whom specific agreements are negotiated that commit to respect culture, economy and environment. Mines in these locations employ extremely diverse workforces whose value systems often come into conflict in on-the-job relationships. Adaptation of individual worker attitudes and industrial operating culture thus both need to occur if there is to be the negotiation of a workable relationship. This paper will discuss ways that NWT diamond mines have adapted to their workforce, to ensure that rights and cultures of their diverse workforce can be respected. Historically, the concept of culture has been dealt with solely through the forum of ?cross-cultural? workshops. Gibson presents a model of a new type of ?cultural-engagement? workshop based on the top ten cross-cultural conflicts that actually arise at a remote mine-site. This model helps managers, team leaders, and workers to tackle in-mine conflicts that arise based on differing value systems of aboriginal and non-aboriginal workers and management. In addition, Gibson suggests that the concept of culture must be more rigorously applied throughout the mine structure and not discussed only in the forum of the cross-cultural workshop.

May 1, 2007