Search Documents

By D. Yuan, L. Yan, M. J. Collins, P. Kalanchey, I. M. Masters

ABSTRACT Pressure oxidation tests have been conducted by Sherritt for a refractory gold-silver project in China. The feed contained 39 g/t Au and 970 g/t Ag; the major gold-bearing minerals were pyrite and arsenopyrite. Because the feed contained a significant amount of silver, which can be refractory to cyanide leaching after pressure oxidation due to the formation of argentojarosite, the test program included investigation of methods to enhance silver recovery. The “lime boil” process proved successful and was incorporated into the flowsheet. Gold extraction from the lime boil product solids was 95–98%; silver extraction was up to 94%.

Jan 1, 2013

By D. D. Liu

This paper proposes a charge induction dust measurement method based on detrended fluctuation analysis (DFA) for use in coal mine environments, based upon electrostatic interference, dust properties, wind speed, particle size, moisture content and other factors. In this methods, sequence x(t) is first obtained through a dust concentration sensing probe, and then the cumulative deviation y(t) is calculated, and y(t) is divided into same lengths. Secondly, a first-order linear fit is used for data of each interval, and mean-square deviation filtered DFA was calculated for each interval. Finally, the dust mass concentration of the corresponding time is obtain by supplemented calibration coefficient and fitted the data point which is the mean and square root for all lengths of interval. Simulation and verification experiments showed that the charge induction dust measurement method based on DFA can reduce coal mine electrostatic interference effects with high accuracy. The design has been successfully applied to select areas.

Aug 1, 2013

By Colleagues from Process and Operation departments, Guy Chevalier

"QCM's pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented.This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.INTRODUCTIONAt the Québec Cartier Mining pellet plant, continuous improvement programs are aimed at increasing levels of consistency and improved chemical, physical and metallurgical properties. This is being accomplished while still maintaining pellet plant production volumes to satisfy market demands.QCM produces three types of pellets for blast furnace use: acid pellets, designated as ""BHF"", fluxed pellets, designated as ""BAF"", and low silica fluxed pellets, designated as ""BSA"". For direct reduction, a low silica acid pellet or DR pellet, designated as ""BBS"" is produced. This low silica DR pellet is used in Midrex and HyL shaft furnaces.The demand for DR pellets has been increasing during the last few years and is believed to continue so in the future. Wanting to be present in this growing market QCM found that it would be essential to work at improving its DR pellets quality. Efforts have been focused on improvements in three areas: SiO2 reduction, elimination of sticking and increasing reducibility. Improvement programs have begun with laboratory research followed by plant trials and full-scale implementation as a cooperative effort among QCM, COREM, and key customers."

Jan 1, 2002

By O. Hall

STOPING at Noranda" is a sequel to "Mining at Noranda". "Mining at Noranda", presented in 1937 (1), sketches Noranda's history, metallurgical problems, exploration, mining methods, mining details, pillar extraction, and costs. "Stoping at Noranda" deals in greater detail with our stoping, the use of sub-level drifts instead of benches, and the drilling out of the stopes with jointed rock drill steel and diamond drills. Sun-LEVEL DRIFT STOPING: Sub-level drift stoping is almost universal throughout the mine and is the standard sroping method in both sulphide ore and rhyolite flux ore. The features that have led to the adoption of this standard are: (1) Continuous symmetrical drilling in sub-level drifts with no delay for blasting. (2) Large-tonnage blasts Saturday night after the drillers have left. (3) Comparative freedom from gas and smoke during the working days. ( 4) The daily safety achieved by having all stope drilling done in drifts. (5) The safety and security achieved by drilling out stopes, floors, and pillars before there is any weighting or cracking.

Jan 1, 1939

By A. K. Watt

"The availability of fresh water to meet present and future needs in Ontario is of concern to an increasing number of people. Rain and snow are the source of our potable water and provide, on the average, some 180,-000 billion gallons of water annually. This amount is reduced to 94 billion gallons a day as a result of the evaporation and transpiration of water and our inability to construct the necessary reservoirs for capturing surplus stream flow.The water used for domestic, irrigation, public supply and industrial purposes amounts to some 7 billion gallons daily at present and will reach 21 billion gallons daily by the year 2000; however, only about one-fifth of the water used is actually consumed, and this, along with the possibilities of water re-use, improves the water supply picture still further.The need for adequate pollution control has accompanied industrial and urban expansion and is an important factor in the extent to which our surplus water is used. In the 10-year period since the formation of the Ontario Water Resources Commission, the cost of water and sewage works constructed in the Province has exceeded one billion dollars. A special effort is now being made to control the industrial pollution situation.Numerous federal and provincial agencies are engaged in hydrologie studies in the Province, providing in-formation of benefit to those involved with water resources management."

Jan 1, 1967

By A. E. Wraith, R. Harris, J. Qiu, R. Parra

Small pilot scale experiments have shown that it is possible to almost fully eliminate the minor elements (ME), namely As, Sb, Bi and Pb contained in smelter dusts by vacuum calcination of mixtures of the dust with sulphidizing agents such as dirty copper concentrate or elemental sulphur at 900 °C and 80 +/- 30 Pa for 90 minutes. The products of this calcination are a residue comprising a purified mixture of copper containing compounds along with the gangue constituents and a high sulphur condensate comprising a mixture of the minor element compounds. In particular, the Cu:ME ratios of the concentrate and dust were increased from 250 and 50, from 28 and 12 and from 36 and 8 to roughly 3000, 3000 and 100 for the calcine, for Bi, As and Sb, respectively. It has also been calculated that (i) the copper content of the vacuum calcine may be recovered by feeding it into a Peirce-Smith converter during its slag blow, and (ii) the resulting recycling could increase the minor element treatment capacity of a smelter by 100 % while also reducing the blister As content by a factor of three. The experimental results are briefly discussed and a treated dust recycling option is examined. Example operating conditions are presented and available commercial technology for the vacuum calcination of the mixtures is reviewed.

Jan 1, 2007

By Mark Sherman, M. Dennis, Raj Rajamani

"The two Alumbrera 36ft (10.97m)dia. SAG mills were sized, using the FDW ""Grindpower 'I program, to treat an average of 1852 tph each. This paper describes how modelling of the shell lifter design, using the Millsoft program, identified milling inefficiencies caused by poor charge motion. This explained the ""as built"" circuit's inability to achieve the throughput rates predcted by the circuit's designer. Use of the Millsoft program to design a new, dramatically different lifter configuration, in conjunction with a different approach to variable speed drive utilization, has resulted in an improved charge motion and a 30% increase in hard ore milling rates. The new lifter design has allowed the designer's predicted average throughput rates to be achieved.IntroductionThe Alumbrera project grinding circuit consists of two 36ft dia. X 17ft EGL, 13 500 kW, variable speed, gearless drive SAG mills coupled to four 20ft dia. X 30ft EGL, 6 000 kW fixed speed, gear driven, ball mills. The circuit is configured as two identical grinding aisles, each consisting of one SAG mill and two ball mills. No pebble crushing circuit was installed due to the expected absence of a critical size fraction in the first years of production. However, the grinding circuit layout does incorporate space for a pebble crushing retrofit. At present, only about 5% - 10% of the new mill feed reports as trommel oversize and is recycled back to each SAG mill using a water cannon.The circuit was designed to be ball mill limited and to treat the four major Alumbrera ore types at rates varying between 68 000 tpd, and 89 750 tpd, depending on ore hardness. Average throughput rate, and hence nominal design rate, for the grinding circuit was 80 000 tpd (1 852tph per line at 90% availability)."

Jan 1, 1999

Several inorganic reagents and organic polymers were tested as depressants in the single mineral flotation of ultrafine iron oxide and hydroxylapatite with Dowfroth 250 as a frother. It was observed that the inorganic reagents and the low molecular weight polymers generally caused dispersion of the ultrafine particles, and consequently their recovery into froth products more or less equaled the recovery of water. On the other hand, the high molecular weight polymers caused different degrees of flocculation of the ultrafine particles, and their recoveries were much lower than the recovery of water. These observations pointed to a need to re-define flotation depressants in fine particle flotation. The traditional definition of a flotation depressant, i.e., to make particle surfaces hydrophilic by forming a hydrophilic film and/or by removing collector and activator coatings, is sufficient for relatively coarse particles. However, to prevent fine and ultrafine particles from floating, a successful depressant should not only make the particles hydrophilic, but also enlarge the particle sizes so that they do not enter the froth product by mechanical entrainment. Polymeric depressants are ideal for these purposes. The different schemes to use polymeric depressants in the selective flotation of fine and ultrafine particles were discussed These schemes involve the integration of the polymeric depressants into other size enlargement processes such as shear flocculation, oil agglomeration, etc., for hydrophobic particles.

Jan 1, 2004

By Pizhi Zhao, Jingwei Zhao, Zhenshan Liu, Yiheng Cao

"A new Al-Mg-Si-Zn alloy designed for automotive outer panel was trial-produced with industrial procedure. The final product shows a strong planar anisotropy. X ray diffraction analysis shows such strong anisotropy is caused by the dominating cube texture component in the final product. The reason for such high cube texture component was investigated by tracing texture evolution starting from the hot roll slab. It is found that certain cube texture components already exists in the hot rolled slab. The density of cube texture component shows as a wavy change through the following1st cold rolling, inter-annealing, 2ndcold rolling and solution treatment. This study shows that the cold rolling in the laboratory can well represent the texture evolution during the industrial production. The results obtained by lab rolling hints that change of second cold rolling reduction has weak effect on the planar anisotropy, when the gauge of hot rolled slab and final sheet are fixed.INTRODUCTIONWith the rapid progress of light-weighting in the automotive industry, aluminum sheets get more and more application as closure panel and structure parts. Recently the dominating alloy for outer panel is 6xxx series, containing the main alloy elements Mg and Si. The popular gradesareAA6016,AA6111, AA6022, and AA6014. These alloys still cannot satisfy the various requirements from automotive manufacturers. Most suppliers of automotive aluminum sheets are developing their own specific grades according to the customer’s demand. To increase the baking response, anew Al-Mg-Si-Zn alloy was designed, concerning the high combination energy between Zn solutes and vacancies formed during the quenching stage of automotive sheet manufacture. This combination is helpful to the precipitation of ß”phase during the paint baking (Wang, 2015,2016; Yan, 2014).The plastic strain ratio (r value)is a key index of the formability of automotive body sheet. A high r value means a good formability. The r values in different directions can be used to evaluate the planar anisotropy of the metal sheets. The trial produced Al-Mg-Si-Zn sheet shows a strong planar anisotropy with respect to r values. Since the r value is tightly related with texture, the texture evolution from hot roll slab (HRS) to final T4P temper was analyzed with X ray diffraction (XRD) to find the reason for the high anisotropy. Besides, the cold rolling reduction (CRR) was varied in the laboratory to modify the texture distribution, i.e., the planar anisotropy."

Jan 1, 2018

By T. H. Patching, D. F. Coates

The Sub-Committee on Rock Classification, Canadian Advisory Committee on Rock Mechanics, has evolved a classification of rocks which should prove useful in studies of rock mechanics. Considered in two stages -actual rock substance and rock mass -the five-point classification involves the geological name of the rock, the rock strength and rock deformation, and, in the second stage, the gross homogeneity of the rock mass and the formation continuity.

Jan 1, 1968

By W. N. Wallinger

The mine and concentrator of Cyprus Anvil Mining Corporation are situated in south-central Yukon, some 120 miles north of Whitehorse. The large lead-zinc concentrator employs conventional crushing and grinding , followed by differential flotation, to produce selective lead and zinc concentrates, as well as a mixed lead-zinc (bulk) concentrate. Since the commencement of operations in 1969, the concentrator has undergone expansions and modifications which have increased the capacity to 10,000 tons per day, and afforded some metallurgical improvements.

Jan 1, 1978

By M. Peshko, J. C. Gingerich, L. W. Matthews

"Noranda has successfully developed and implemented two leading-edge mineral exploration technologies — hyperspectral remote sensing and 3-D seismic surveying. Airborne hyperspectral imaging provides detailed geological and mineralogical mapping capability at both a regional and project scale that facilitates improved selection of prospective terrain and an accelerated exploration cycle. Noranda, in partnership with Falconbridge, has licensed the exclusive use of the Earth Search Sciences Inc. (ESSI) Probe-1 hyperspectral scanners (128- channel, 0.43 µm to 2.5 µm spectral range) that are capable of mapping in excess of 3500 km2 per day at 10 m pixel resolution. The technology has been successfully deployed on four continents over a broad range of terrain from desert to boreal forest and the high Arctic.To augment the company’s deep search initiatives, Noranda has successfully modified and implemented existing 3-D seismic technology to help targeting massive sulphides located at depths ranging from 500 m to 2000 m. In the fall of 1998 and early 1999, Noranda completed an 18 km2, 3-D seismic program in eastern Canada by successfully drill testing acoustic impedance anomalies locating massive sulphides at depths in excess of 1100 m."

Jan 1, 2002

By J. S. Godard

The mining developments in western Quebec have shown the ores of this district to be more complex in character than was at first expected. When the initial discoveries were made it was thought that the ores would be similar in character to those of Kirkland Lake and Porcupine areas. Developments have since shown that although the ores along the southern margin of the belt are somewhat similar, those within the belt, constituting by far the greater proportion, are vastly different, being complex mixtures of base-metal sulphides carrying values in the precious metals. These mixtures of base-metal sulphides of copper, zinc, and iron, present several problems to the metallurgist, especially in their concentration into marketable products. For the purpose .of this paper the following classification may be made of the ores of the district. Group I. - Milling Ores: (a) Ores in which~ arsenopyrite is the predominating sulphide. In this class of ore the gold occurs in fractures in the quartz and is associated to a lesser extent with the arsenopyrite and pyrite. Examples of this class of ore are the Granada, south of Pelletier lake, and the O'Brien and the Thompson in Cadillac township. (b) Ores in which iron pyrite is the predominating sulphide and gold is the valuable constituent. This may also be classed as a concentrating ore-Group III.

Jan 1, 1928

By P. B. Demarsh

"Location: - Mine village of Perron, 11 miles east of Val d’Or in northwestern Quebec.Life; - Started production 1932, ceased 1951.Ore: - Flat lying quartz tourmaline veins within granodiorite. Gold values related to coarse segregations of pyrite. Specific gravity 2. 80.Capacity: - 30 tons 1932-35; 125 tons 1935-37; 350 tons 1937-51.Assay: - Heads 0.21 to 0.34 oz. per ton. Grade obtained by mining 600 tons daily, sorting belt reject 250 tons, balance to milling; tailings loss 0.003 to 0.005 oz. per ton; extraction 9 8. 5%.Grind: - 70% minus 200 mesh. Detention time 26 hours.Treatment: - Cyanidation process.Reagents: - Per ton, aero cyanide (NaCn) 0.36; unslaked lump lime 1.50; zinc 0. 03; lead acetate 0. 006; steel consumption 2. 50.Water: - Equal mixture of swamp creek water and underground seepage.Cost: - Per ton, sorting and crushing 0.21; grinding 0.31; cyanidation 0.11; filtration 0.05; precipitation 0.02; miscellaneous 0.22; total 0.92.Power: - Hydro-electric, 25 cycle, 12, 000 volts reduced to 550 volts.Labour: - 95% Maritime and European, balance Quebec and Ontario.Tailings: - Absorbed over large swampy area on barren mining claims.Personnel: - 1 7 men including supervision.Flow sheet: - Canadian Mining Manual 1947"

Jan 1, 1966

By R. Cammack

"A fundamental component of the Hoek–Brown empirical rock failure criterion is assessing an appropriate mi constant. In developing their empirical criterion Hoek and Brown normalised triaxial test results by dividing the principal stresses at failure by the uniaxial compressive strength to provide mi values for typical rock types. Experience shows that Hoek triaxial tests for individual lithology types commonly have a large inherent scatter. In addition, tests are often conducted on core from random locations, which although being of one parent rock type, display variations in density as well as minor variations in grain size and alteration.This paper presents experience from projects the authors have been involved in which large sample populations of triaxial and UCS tests on similar rock types were available. Geophysical logging data was also available for some projects. The methods used to estimate the compressive strength for each sample and the effects on normalising the data sets are described. The variability of the data and uncertainties and assumptions involved in the process of assigning a mi value from the normalised data are also discussed."

Jan 1, 2015

By P. V. Amosov, V. A. Masloboev, D. V. Makarov, S. G. Seleznev, A. A. Baklanov

"The development of industry and intensive use of natural resources leads to a significant decrease in the share of reserves of rich ores, deposits of which have nearly all been exploited. Large amounts of displaced rock mass are accumulated, significant emissions of gas and dust from mining, dust from dumps and tailing pits, ingress of chemicals and toxic elements in surface and groundwater all can have negative effects on existing ecosystems and human health. Especially dangerous is the impact in Arctic regions with extreme climate conditions. The maintenance of overburden dumps and tailings dams requires significant capital and material costs. In this paper, some mining enterprises of the Murmansk region, in the Russian Federation, consider the environmental problems of the industry and propose some solutions.INTRODUCTIONThe safety of environment during the extraction and processing of minerals is a very acute problem throughout the whole world. The problem acquires a specific character in the Russian Federation. There, rather poor minerals, often existing in unconventional forms and including several mineral components are processed. The Russian mineral base has a specific geographical location; most of the deposits under operation are located in the Subarctic or Arctic regions, as well as in Siberia and in the Far East. Vast amounts of rock waste and tailings pose serious economic and ecological problems in mining regions. The operation of overburden heaps and tailings requires considerable capital and material costs. The dumps withdraw vast lands from potential commercial use. Large amounts of mined rock disturb the existing geological balance; emissions of gas and dust which accompany the mining operations, dusting of waste heaps and tailings, emissions of reagents and heavy metals into natural surface and ground waters all can produce negative effects on existing ecosystems and human health."

Jan 1, 2016

By A. H. Lang

"The Cordilleran region of western Canada includes most of British Columbia and the Yukon and pares of Alberta and the Northwest Territories. The western part of this region was for about 50 years the principal mineral producing area of the Dominion. It lost this distinction in 1907 when production from the mines of the Canadian Shield took the lead, but it continues to provide about 15 percent of the total Canadian production. In 1945 the total mineral production of British Columbia and the Yukon was valued at $65,302,900, of which about 80 percent was derived from metals.This paper is intended to serve as an introduction co the more derailed Cordilleran papers. Part I includes a brief synopsis of the complex geology and diverse types of mineralization in the region and Parr II collates the main structural principles exemplified in the derailed papers, and draws some conclusions regarding the application of this information to prospecting."

Jan 1, 1954

By S. P. Lowe

Introduction In the following pages a general description is presented of the concentrator and cyanide plant of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, together with some account of the steps which have led to the adoption of the present practice. For an account of the preliminary test-work and pilot-mill operation, the reader is referred to a recent paper by R. E. Phelan on the History of Flin Flon Mine up to Construction (1). Additional notes may be found in a paper which the writer presented at the Annual Meeting of the Institute in 1930 (2). The first ore was crushed in the present plant on July 1st, 1930, and the first ball-mill was started one month later, on August 1st. Since that time, production has been continuous with the exception of one month lost during a strike in the summer of 1934. There have been no major changes in equipment or methods of treatment since the present plant was built, but many minor changes have contributed to the improvement in results obtained and to the increase in capacity to the large tonnage now being milled. The accompanying flow-sheets indicate the equipment used in the several plants, with the average life and repair cost. As originally built, the concentrator was to treat 3,000 tons per day, but the capacity has been increased to 4,400 tons. The methods adopted to make possible this increase in tonnage will be referred to below. It was the intention to produce two classes of ore: (1) a heavy sulphide, and (2) a disseminated ore. The mill was consequently divided into two sections, each adapted for most efficient treatment of one particular type of ore. However, it was soon found that it would be impossible to mine the two classes of ore separately, so it was decided to treat open-pit ore, which varies greatly in character, in the sulphide section, and underground ore, which is fairly constant, in the disseminated section. This segregation is still maintained.

Jan 1, 1935

By K. J. Fair, G. Van Weert, J. E. Schneider

"IntroductionCyanidation is the principal process for extracting gold from ores . Many primary gold ores, however, are partially or totally refractory in the conventional cyanidation process.Considerable success has been achieved with new gold leaching techniques, such as intensive cyanidation, pressure cyanidation, carbon-in-leach cyanidation, etc. These techniques however, do not offer substantial gains in gold extraction from refractory pyrites.The more drastic pretreatment processes such as roasting, chemical oxidation, autoclave oxidation, and bacterial oxidation all utilize oxidation to break down the structures of pyrite and arsenopyrite. This generally renders the gold amenable to cyanidation.Comparative cost studies indicate that the oldest commercial pretreatment method, i.e. high temperature roasting, is currently the least expensive option if the sulphuric acid can be sold. It operates with air at atmospheric pressure and is characterized by fast reaction rates. For an alternative hydrometallurgical con centrate treatment method to be competitive, it too should operate with air at atmospheric pressure and with fast reaction rates. The NITROX process meets these conditions."

Jan 1, 1986

By M. R. Coffin

Since the plant startup in 1972, the leaching and jarosite precipitation circuits at the zinc plant of the Kidd Metallurgical Division have been reconfigured several times to improve overall performance, and/or to respond to market conditions. For the most part, the circuit changes have been driven by two market factors: the price of zinc and the price of silver. Until recently, circuit modifications undertaken to improve zinc extraction and recovery came at the expense of silver recovery, and vice versa. In 2004, the plant was modified once again to produce a precious metals-bearing residue, but additional leaching circuits were added to ensure that zinc extraction and recovery did not suffer as a consequence. The development of the zinc plant of the Kidd Metallurgical Division is updated in this paper, with a focus on the recent circuit modifications and associated control strategies that were implemented to maximize zinc and precious metals recoveries, and control the quality of the jarosite residue.

Jan 1, 2006