Search Documents

By A. Rousselet, H. Gilbert-Tremblay, A. Berton

"Robex Resources interrupted production at the Nampala Mine in September 2014 following throughput and gold recovery results which were below expectations during the first months of operation. After a thorough plant audit, an important brainstorming took place in order to identify an economical path to resume production. It was clearly identified that a significant investment was necessary at the concentrator prior to restarting the plant, namely the addition of a ball mill and a new elution system.The mineral processing simulation software USIM PAC was used in order to simulate the grinding circuit in design. The simulations’ outputs allowed the ball mill characteristics and the surrounding classification devices to be designed with more accuracy. Many ball mills available from second hand retailers were therefore studied in the simulated circuit. The chosen ball mill, which was in perfect condition, had the advantage of being available for rapid delivery on site.The paper first describes the ball mill sizing method in comparison with the conventional Allis Chalmers method. It then describes the phase 2 concentrator start-up (that took place in 2016) with the commissioning of the ball mill, the classification circuit, the gravity concentration, the four (4) new carbon-in-leach (CIL) tanks, and the Zadra elution system (The phase 1 start-up took place in 2014). It finally provides production data compared to expected simulation data, as commercial production was reached in January 2017.IntroductionDesigning a new concentrator or new equipment within an existing concentrator requires significant efforts to identify possible bottlenecks and their causes (i.e. limiting equipment or sectors) and accurate sizing of major equipment can have a tremendous impact on the economy of the whole project. In the presented case study, the ball mill was the critical equipment and oversizing it could have brought the Capex to a level where the project would not have gone through. Inversely, undersizing the mill could have resulted in lower production and therefore no economic viability for the project once it is in operation.During engineering studies, equipment sizing often relies on a static mass balance and one-by-one sizing of all pieces of equipment. The sizing is then left to the equipment manufacturer or in the case of mills, evaluated with empirical models mostly relying on the Bond equations (Allis Chalmers method) [Rowland and Kjos, 1978]. This methodology shows the disadvantage of not considering interaction between equipment in a mineral processing circuit, especially when recirculation occurs. Also, it has the disadvantage of not using the more advanced grinding models that include the use of the whole particle size distribution as well as phenomenological components by only using limited parameters in the ore particle size distribution (i.e. the P80). This can be explained by the lack of data that sometimes needs to be gathered in order to tune the more advanced models but also by the conservative mindset in mineral concentration engineering which does not always favor the use of process simulation. In many aspects of process engineering, Soutex has demonstrated its affinity to using simulation in order to size equipment with more accuracy, consider process variability, simulate complex systems, and study supply chain management (Berton et al., 2015)."

Jan 1, 2018

By G. Eaton

Safety management is an important mortal and business function in construction. Contractors have traditionally tracked and reported lagging indicators, e.g. fatalities and lost-time accident rates, to measure their safety performance and stay in compliance with relevant regulations. Over the last several decades, contractors became more proactive in their approach to safety and developed programs that track leading indicators, e.g. safety audits and safety climate. In particular, safety climate measures workers? perception of safety management and its effectiveness in the workplace. Past literatures indicated that, while some industrial construction contractors ignore safety climate measures, others are limited by a lack of a formal means to measure safety climate. In this study, a survey approach is used to measure an industrial construction contractor?s safety climate through three key areas: management commitment, job control, and general safety climate. As a pilot study, a total of 214 individuals at a fabrication facility participated in the survey to verify the validity and effectiveness of the proposed survey approach. This survey study also confirms that job control and management commitment have a positive correlation and that worker demographics have an effect on respondents? perceptions of management commitment.

Aug 1, 2013

By A. L. Nunes, J. R. E. Garcia, G. Silva, U. Prasad, C. Rabe

"Drilling through the Guayabal shales, a gray calcareous shale, and the C1 to C100 formations, a well-cemented calcareous-sandstone in Corralillo field, Mexico, is a challenge due to severe wellbore instability problems. Additionally, there has been a history of ineffective reservoir stimulations by hydraulic fracturing. To predict and mitigate these subsurface issues, it is essential to characterize the mechanical properties and rocks strength for a better prediction of borehole stresses and collapse pressure during drilling. Various correlations can be used to estimate and/or determine the unconfined compressive strength but most of them are based on transit time and porosity.In this study, grain size distribution was combined with acoustic travel time, porosity and static Young’s modulus to develop a rock strength prediction model for the turbiditic sandstones of the Chicontepec basin. The main reason this combination of parameters was employed was because of the wide variations in rock strength estimated using traditional porosity-based correlations such as the McNally’s (1987), GMI-Jizba-E’s and Bradford’s (Bradford et al., 1987).To develop a new correlation, a geomechanical and microstructural campaign was initiated. Mineralogy by X-ray diffraction, pore and grain sizes by petrography, clay distribution by SEM and porosity by mercury intrusion porosimetry were measured. Static and dynamic Young’s moduli and Poisson’s ratios were acquired by triaxial and ultrasonic measurements on undisturbed sandstone samples from the Chicontepec basin. More than ten offset wells with wireline data, including transit time, porosity, density, resistivity and gamma ray, were used for reservoir and geomechanical characterizations.Our analyses lead us to propose a new correlation for predicting the uniaxial compressive strength (UCS) of sandstones of the Chicontepec Basin as a function of transit time and grain diameter, both of which can be derived independently from destructive laboratory tests. Our results also highlight the importance and value adding of a combined approach incorporating grain size analysis in the rock strength prediction. The UCS predicted using the transit-time and grain-size-based model presents a median value (P50) of 76 MPa, P10 of 55 MPa and P90 of 89 MPa."

Jan 1, 2015

By J. E. Udd

A core sample for this study was taken from the sulphide ore of the Geco Mine. The subsequent research was based on the assumption that a part of the scattering of strength-grade data could be correlated with variations in the chemical and/or mineralogical compositions of the samples. The results demonstrate clear relationships between strengths in tension and compression and the zinc-iron contents of the rocks.

Jan 1, 1977

By J. H. Fulton

Summary Considerable test work has been done with the detachable type of carbide bit. In general, these bits improved drilling operations, but at a bit cost .greater than was compensated for by the reduction in man-hours of labour. Too few bits continued in service for the possible drilling life of the carbide inserts, and technical improvements or lowered first cost, preferably .both, are indicated ?in order that the bits can be generally acceptable as an economical drilling tool. In ?preliminary test work, the drill rods .with ?one insert of the chisel-bit type appear to be more trouble-free, to have a longer life, and to give a somewhat lower bit cost per foot drilled, than other types. INTRODUCTION The object of this paper is to outline briefly the 'methods used and the results obtained in test work with tungsten carbide bits used in combination with the smaller bore, lighter weight rock drills. As various articles have appeared in the past few years giving the historical background ?and early development of carbide ?bits, this information will not be repeated. Table I lists the equipment used in the test work. The stopers weigh about 95 pounds and the jackhammers with airleg from 97 to 110pounds. The smaller rock drills are stated to deliver about 2,200 blows per minute at 1 to 30 rotation and to require 85 to 95 cubic feet of air at around 100 pounds pressure.

Jan 1, 1950

By A. G. Spencer, A. D. Taylor

This paper discusses some of the advantages and problems associated with the selection of large unit equipment for a metallurgical plant. A given flowsheet and material balance for an iron ore concentrator is assumed. Then two plant designs are developed, one utilizing a number of smaller-size equipment units and one utilizing the largest available equipment units. The mechanical and electrical problems are discussed and a comparison of capital costs is made. Finally, brief consideration is given to a plant de-sign using units larger than those which are currently available.

Jan 1, 1968

By M. F. Goudge

This paper is intended to call attention to the manifold uses of limestone in industry; to indicate the types of limestone desired by some of the large consuming industries; and to give some information on the resources of limestone in Canada, so that an idea may be obtained of the present and future possibilities for limestone production. The word limestone is used in the usual broad sense to include both high-calcium limestone and the highly magnesian variety known as dolomite, as well as all intermediate types. Lime is simply calcined limestone, and in this general paper its uses have been included with those of raw limestone. It is of interest, in dealing with this subject, to glance back over the early history of the utilization of limestone, for by so doing we see that limestone has been of importance to mankind since the beginning of civilization and has contributed in no small measure to the development of a number of the arts and sciences. One of the first uses, if not the first use, of limestone was in connection with the making of lime for plastering purposes. This use antedates civilization. In the day of the ancient Greeks and Romans, the art of plastering had been brought to a state of perfection that is not nearly approached by the modern artisan.

Jan 1, 1930

By John H. McKillop

Industrial minerals production in Newfoundland in--creased in gross value by a total of 175 per cent during the ten-year period from 1954 to 1964. The Province accounts for all of ?Canada's fluorspar production and contains one of the most important fluorspar districts in North America. It is also the only producer of pyrophyllite in Canada, and quite recently has become an important producer of asbestos fibre. Limestone, gypsum, brick shale, sand and gravel also ?Contribute appreciably to the expanding industrial minerals phase of the Province's rapidly growing mining industry. Geological diversity characterizes Newfoundland's industrial minerals: Pyrophyllite deposits were formed by contact metamorphism of predominantly volcanic Proterozoic rocks. Fluorspar deposits are fissure-filling veins having the characteristics of typical epithermal deposits. Chrysotile asbestos production comes from one of the Island's serpentinized ultrabasic belts. Limestone is produced at three localities; two of them in the extensive carbonate rocks of the west coast. Gypsum production comes from a thick evaporite (gypsum and anhydrite) sequence in the Carboniferous rocks of the St. George's Bay area. Introduction

Jan 1, 1965

By Jason Palmer

"Water in mining is the commodity that has driven the mining industry for decades. Often used frivolously, modern economic and social pressures are forcing change to use less water and to improve the quality of water and effluents. Used in many processes, water is ultimately consumed in tailings disposal and technologies which can increase the recovery of water are constantly being developed. Filtration and thickening are often seen as competing technologies for water recovery however new cases are developing that show significant advantages can be achieved by combining the two technologies to develop the most effective solution. Supported by case studies this paper investigates the merits of each of the technologies and which strategies of combining the two produce the best outcomes.INTRODUCTIONMineral processing applications generally require water for the processing of ores, whether utilising physical or chemical methods. Water is first added in the milling stage and additional water added as required throughout the circuit. Water losses from the circuit are principally associated with the tailings stream. Optimised water recovery is necessary both because it is a scarce commodity and to minimise the environmental impact.Water recovery is usually accomplished through a sedimentation or filtration processes. Water can be removed from the tailings impoundment by evaporation but this does not improve the mine’s water consumption. The water recovery methodology also determines the water quality; increasing water recovery concentrates solutes in the process water and may create recirculating loads of fine solids."

Jan 1, 2016

By G. Gabra, M. Nagamori, J. J. Panneton

"RESUMELa calcination contrôlée de 10 serpentine permet de produire de 10 magnésie active. Le degré de I'activation est mesure par 10 solubilité du magnésium dans les acides faibles tel que I'acide acétique, La serpentine contenue dans les résidus d'amiante du Québec peut donc être activée par calcination. Le teneur en magnésie active des rejets d'amiante calcinés est fonction de divers paramètres: température, temps de calcination, granulométrie, etc. Les rejets d'amiante de différentes provenances démontrent des comportements thermochimiques différents qui sont étudiés dans Ie présent travail au moyen d'ATD, de TG, de la diffraction des rayons X et de la lixivation par l'acide acétique. On constate qu'un maximum d'environ 80% de la magnésie totale peut être activé dans certains rejets d'amiante du Québec et Ie degré d'activation dépend de la provenance.vIntroductionOn sait depuis longtemps que la serpentine, Mg3Si2O5(OH)4, un silicate hydroxylé de magnésium, devient amorphe lorsqu'elle perd de I'eau d'hydratation entre 600 et 700 °C. La serpentine ainsi calcinée est alors dissociée en magnésie et en silice. Cette magnésie, dite active, est soluble dans un acide faible ou même dans les solutions de sels d'ammonium.Plusieurs precédés chimiques ont été proposés afin d'extraire sous forme de composés magnésiens la magnésie de la serpentine. La plupart de ces procédés comportent une activation par calcination de la serpentine préalablement à une Iixiviation par un acide ou par une solution d'un sel d'ammonium.Malgré la contamination par Ie fer et par d'autres éléments, les compositions chimiques des rejets de différentes mines d 'amiante du Québec, présentées au tableau 1, sont très proches de la serpentine typique. Puisque Ie degré d'activation de la magnésie varie grandement d'une serpentine à I'autre lors de la calcination, la première étape de la recherche sur la transformation chimique des rejets d'amiante du Québec se résume à une étude de leurs comportements thermochimiques."

Jan 1, 1982

By Allan F. Lawrence

"I AM SURE you do not expect from me any learned dissertation on the problems and opportunities of the mining industry. Y our program committee must have recognized my limitations when issuing the invitation to speak to you, because they very thoughtfully left the subject wide open.With the leeway thus granted, I hope that you will bear with me for a few minutes while I try to clarify the impressions of the mining industry that I have gained in the very short time I have held the Mines portfolio and some of the parts that government bas or should have in furthering its development.As I see it, it is the duty of the Mines Department, as an arm of the provincial government, to balance the proprietary rights of all the people against the interests to whom the privilege of developing our resources are, in a s e n s e, leased. To strike a fair balance is not always easy, nor is it possible always to satisfy both sides. Still, under the free enterprise democratie form of government to which I think we al! subscribe, no better way of handling the problem has yet been discovered."

Jan 1, 1968

By T. M. Korzekwa, R. L. Cavanagh

Following considerable experience with the beneficiation of Wabana iron ore by standard methods, a study was made of the benefits to be obtained by semi-reduction. The basis of the laboratory program was an extensive mineralogical and liberation investigation which guided subsequent work. Partial reduction and beneficiation on a laboratory scale was carried out on lump ore and fines. The reduced ore was magnetically concentrated and the concentrated fines were briquetted. Data are presented on reducibility, sizing vs reduction rate, magnetic cobbing and separation, and the elimination of phosphorus. Past work is reviewed briefly and comments are made on the relation of laboratory to pilot-scale tests.

Jan 1, 1967

By J. Keith Haddock

"IntroductionThe Bienfait Mine is operated by Bienfait Coal Company Ltd., one of the Luscar Limited group of companies. Situated 5 km southeast of the town of Bienfait, Saskatchewan, it can produce 2.0 million tonnes of lignite annually in addition to 158,000 tonnes of char from a carbonization plant located on the property. Geology The economically mineable coal seams of the Estevan area are found in the Ravenscrag Formation. The lignite-bearing sands, silts and clays were deposited in Early Tertiary age, in an inland sea centred in the Williston Basin of North Dakota. The top of the Ravenscrag is an erosional surface, overlain by Tertiary or Quarternary sands and gravels or glacial till. The regional structure is a gently plunging syncline which dips to the southeast at about 0.3 degrees. There are minor undulations in the Bienfait area which are due to differential subsidence during deposition. Sporadic faulting is probably a result of glacial pressures, and preglacial and glacial channels are responsible for washout zones and the abrupt irregular subcrop found in the area. There are two economic coal seams in the Bienfait area, an uppe; seam locally known as the Roche Percee, and a lower seam, the Estevan. Both seams have been extensively mined since lignite mining began in the area in the late 1800s. The Roche Percee remains only in a small portion of the Bienfait Mine and comprises a very minor portion of the reserves. It averages 1.74 m thick under 8.1 m of overburden. The till rests on top of the Roche Percee and due to weathering the seam is generally of poorer quality. The Estevan seam comprises the majority of reserves at Bienfait. The main seam which is being worked on consists of an upper bench averaging 2.75 m, a carbonaceous parting of 0.21 m, and a lower bench of 0.92 m. Overburden depth above this seam varies from 21.0 m to 38.0 m."

Jan 1, 1985

By J. W. Merks

"Simulation is the process of designing a computerized model, of a system or procedure, for the purpose of understanding its behaviour and developing strategies to control its operation. Simulation models are rapidly becoming an effective tool for mineral processing plants. Powerful software and fast hardware are more readily available than a basic understanding of the theory of mathematical probability and applied statistics that process simulation models demand.Simple spreadsheet software can be used to develop simulation models that take into account any set of conditions at a mineral processing plant. In addition to an unbiased estimate for each variable in the set on which two-and three-product formulas are based, reliable variance estimates for all variables are required. How to estimate variances, effectively and at the lowest possible cost, and how to compute variances for simple functions such as the metal content of a quantity of ore or concentrate, or more complex functions such as the percentage recovery at a mineral processing plant, are the key to useful simulation models.IntroductionSimulation models for systems and procedures have become one of the most powerful and effective applications for computers( 2.6). Simulations are applied to a wide range of scientific and engineering disciplines. Generally, a model is designed to investigate the effects of changes in and interactions between a set of variables before a system is in operation or a procedure is implemented, by simulating weeks, months, and even years of operation, in a few minutes of computer time. Along with practical and useful applications always comeabuse and misuse. For a simulation process cannot be more reliable than the methodology that was applied to design the model, to estimate variables and variances, to check performance, and to verify validity. A mineral processing plant is a dynamic system that changes continuously as a function of time but within probabilistic constraints that can be estimated by applying statistical tools and techniques to the variables and variances that interact in the system.A model should be designed to simulate not only the set of variables but also the variance for each variable. Models in which constant variances are used to generate normally distributed random numbers, are less realistic than models in which the variances are simulated first, and then used to simulate the variables."

Jan 1, 1991

By P. Dinham, G. C. Summerton, N. McCulloch, S. Dowling, D. C. Craig

"Development of a process for the treatment of a nickel copper matte rich in the minerals heazlewoodite, chalcocite and bornite has demonstrated significant base metal recoveries and metal separation efficiencies. The determination of chemical and mineralogical changes occurring in the individual leaching stages in laboratory experiments has enabled a better understanding of the complex leaching chemistry. The chemistry and mineralogy of the piloting and laboratory processes are discussed.INTRODUCTIONThe nickel-copper sulfide ores of the South African Bushveld Complex are among the most important Platinum Group Metal (PGM) bearing ores, and contain the world’s largest reserves of platinum. The treatment used in the recovery of PGMs from these ores includes three types of processes, namely ore concentration using physical techniques such as flotation and gravity separation, concentration by pyrometallurgical means, hydrometallurgical extraction of the base metals followed by the PGMs. Following milling of the ore, flotation involves the separation of high value minerals from gangue by taking advantage of the differences in their hydrophobicity. These differences are generally maximized through the use of a surfactant or wetting agent. Concentrates are then thermally treated and melted which brings about physical and chemical changes that enable the recovery of base metals and PGMs. The main aim of the smelting and converting process is to separate and eliminate the valuable metals from the bulk of the unwanted gangue and essentially all of the iron and to concentrate the metal VALUES (into a high grade converter matte. The matte can be further enriched by magnetic separation, producing a PGM-rich magnetic fraction and a base metal-rich non-magnetic fraction. The magnetic fraction is treated by hydrometallurgical processes to produce a PGM concentrate which is further refined to separate and purify the individual metals. The non-magnetic fraction is treated to produce marketable metal VALUES (such as nickel, copper, cobalt and to a lesser extent PGMs. The principal objective of any hydrometallurgical extractive process is to leach the desired elements selectively into an aqueous phase so as to separate them from the bulk of the material. (Crundwell, Moats, Ramachandran, Robinson and Davenport, 2011; Hundermark, Mncwango, de Villiers and Nelson, 2011)."

Jan 1, 2012

By M. Tiedtke, T. Crary, P. MacPhail, M. Ounpuu

"The SGS carbon-in-pulp (CIP) / carbon-in-leach (CIL) model was used to evaluate and optimize the carbon circuit at Alamos Gold’s Young-Davidson Mine. Plants samples (pulp and carbon) were tested in a series of small scale batch experiments to determine rates of gold leaching and adsorption on carbon from a combined flotation concentrate/tailing product. The testwork data, along with existing plant data were then used to model the performance of the existing CIL plant and optimize the circuit to improve performance and overall recovery. The primary purpose of the modelling exercise was to determine the most cost effective way to lower solution losses at the plant. The modelling was also used to learn how the various parameters in the CIL circuit affect solution losses and the gold inventory tied up on the carbon. This resulted in recommendations for minor changes in the CIL flowsheet, which were successfully implemented in the plant. The approach, results and plant changes are presented.INTRODUCTION This paper presents the details from testwork conducted on samples from Alamos Gold’s Young- Davidson gold mine which is located near the town of Matachewan, approximately 60 km west of Kirkland Lake in Northern Ontario, within the southwestern part of the Abitibi Greenstone Belt. The objective of the test program (completed by SGS Canada in 2013) was to investigate and model the combined flotation concentrate / tailing carbon-in-leach (CIL) circuit and suggest ways to improve gold recovery. The metallurgical test program included mineralogy, rheology, and carbon modelling testwork. Plant information was provided during the test program and used in the optimization process. Upon completion of the testwork, plant changes were recommended and implemented at site (October 2014). Plant results from 2014 to 2017 confirmed the modelling results."

Jan 1, 2018

By M. R. Campbell

"IntroductionON THE LAST DAY of December, 1951, a half-century of steel production was completed in the open hearth department of Dominion Iron & Steel, Limited, in Sydney, Nova Scotia.During that period, almost every known variation of basic steel making practice was used in working out a steel making process which would overcome the difficult metallurgical problems imposed by the use of Cape Breton coal and Wabana ore.This paper is presented as a brief review of these steel making practices, setting forth the fundamental metallurgical factors involved in their success or failure.Establishing the IndustryThe story of steel production at Sydney is closely interwoven with that of coal. The steel industry owes its inception to a desire on the part of the Dominion Coal Company, which was incorporated in 1893, to improve its marketing position by increasing sales of slack coal and providing a year-round demand for its product. Accordingly, the Dominion Iron and Steel Company, Limited, was incorporated on March 30th, 1899, with Mr. H. M. Whitney -who was President of the Dominion Coal Company -as its first President. The new Company was given powers to manufacture and process iron and steel, and to mine all minerals, including coal.A strong inducement to the industry was the bounty offered by the Dominion Government for the production of both iron and steel."

Jan 1, 1952

By P. Condori

Palabora Mining Copper (PMC) has two autogenous mills that have been in operation since 1976. The mills were originally designed to treat 30 000 t/d of open cast copper ore in a closed circuit with cyclones. As the ore body went deeper the open cast method of mining was changed to block caving, a consequence of this was the dolerite content (hardest barren material) increased significantly, increasing the production rate of pebbles and thus reducing the milling capacity. In order to cope with the increased ore hardness and to increase mill capacity, a second ball milling stage and pebble crushing were incorporated to the circuit. The above actions created new challenges to the circuit operation and bottlenecks in different areas of the milling circuit. This paper reports the holistic work performed on the Palabora autogenous milling circuit including the implementation of a mill constraint control scheme, the implementation of a pebble removal system from the circuit and a new circuit configuration. The achieved plant stability and increment of ore throughput are also reported in this paper.

Jan 1, 2012

By Wei Wang

The SMCO copper plant is located in DR Congo, and was designed by China NERIN Engineering Co., Ltd. The process is a typical hydrometallurgical plant with Leach-SX-EW, with the project treating the oxide minerals with agitation leaching, followed with three stage of solvent extraction and two stages of stripping, and using permanent SS cathodes to produce LME grade copper. Because of the special characteristic of the ore, what contains 2 different type of oxides (one high carbonate oxide and the other low carbonate), there are several new technical measures that have been developed and adopted for the plant. For example, different grinding, leaching, and filtering are used to treat different oxides. This paper, presents the project process, engineering design, construction and commissioning. The paper also describes some of the problems encountered during plant commissioning, such as the agitation leaching tank issues, and corrosion in the settler-mixer. This paper discusses some NERIN solutions to these problems, and explains the use of the CN filter, which is used to filter PLS to treat high level suspend solids, instead of the traditional sand filter. Finally, this paper also proposes steps / measures for further improvement for future plant operation.

Jan 1, 2014

By B. Damjanac, S. Maxwell, D. Chorney, M. Grob, F. Zhang, J. Hazzard

"A hybrid discrete-continuum numerical scheme is developed to study the behavior of hydraulic fractures crossing natural fractures. The fully coupled hybrid scheme utilizes a discrete element model for a core domain, within which the hydraulic fracture propagates and interacts with natural fractures, and a surrounding continuum domain to better approximate boundary effects. The results show that the behavior of hydraulic fractures crossing natural fractures is affected by a combination of factors. Nevertheless, three fundamental crossing scenarios can be identified from all of the simulations: no crossing, partial crossing, and direct crossing. Each crossing scenario has a distinct injection pressure history which may suggest guidelines for interpreting field hydraulic fracture injection data. Additionally, the capability for these models to generate synthetic microseismicity makes them appealing for the integration of microseismic field data with the reservoir geomechanics for ultimately providing a practical engineering tool for improvement of well completion and stimulation. The model is capable of examining and verifying four different shear deformation mechanisms associated with a propagating hydraulic fracture. The natural fracture can fail solely due to the stress perturbation of the passing hydraulic fracture or it can fail due to a combination of stress and pore pressure changes across different types of interaction scenarios. The simulations also illustrate that the level of fracturing complexity increases as the number and extent of the natural fractures increase. INTRODUCTIONAlthough hydraulic fracturing technique has been applied extensively as a reservoir stimulation technique in the oil and gas industry for over 60 years (Economides & Nolte, 2000), it is one of the key factors promoting the shale gas boom in the past decade (King, 2010; International Energy Agency, 2014). The hydraulic fracturing of shales can be differentiated from hydraulic fracturing of conventional reservoirs by the fact that shale formations often have a pre-existing discrete fracture networks which greatly impact the hydraulic fracture propagation. Based upon field production data as well as microseismic observations, it is believed that so called “fracture complexity” may result from interactions between a created hydraulic fracture and pre-existing natural fractures and planes of weakness (Warpinski, 2009; Maxwell & Cipolla, 2011)."

Jan 1, 2015