Search Documents

By H. Wotruba, J. Heizmann

"The use of shotcrete is a mandatory means for rock support and therefore for safety in many underground mining operations. If shotcrete gets into the flotation feed though, it can negatively influence the flotation process. This especially occurs when sublevel stoping, cut-and-fill or room-and-pillar methods are applied because as the mining face moves on, formerly applied shotcrete layers are mined together with the ore.As shotcrete does not differ significantly from fluorspar ore in its physical properties it gets moved through the comminution process and is fed to the flotation plant like the ore. To prove the influence of shotcrete on the flotation process, a laboratory test series was conducted at the Unit of Mineral Processing (AMR) of the RWTH Aachen University. The shotcrete grade of the flotation feed was varied between 0 and 10% through addition of pure shotcrete. Flotation parameters and also reagent dosage were held constant apart from the addition of the pH regulator, which was dosed to reach a constant pH of 8 at the flotation start. Results showed that with increasing shotcrete grades in the flotation feed the fluorspar recovery as well as general mass recovery decreased. The enrichment factor of Fluorspar also decreased with increasing shotcrete grades in the feed.In an effort to eliminate the shotcrete contamination of the flotation feed, a feasibility study for use of sensor-based sorting prior to the comminution process was conducted. Rock sorting not only reduces the bad influence of shotcrete on the flotation process, but also reduces comminution costs. INTRODUCTIONShotcrete is used in underground mining on a regular basis. It is used for rock support and therefore to increase safety in the underground mining environment. In mineral processing the presence of shotcrete can cause difficulties for example in the concentration processes. In flotation the highly sensitive reagent mixtures can be disturbed by the chemical activity of shotcrete and therefore recovery rates and selectivity of the process can suffer.Shotcrete is a special form of concrete which is applied pneumatically with high velocities and is compressed by its impact energy. Since the process is especially suitable for work in difficult environments and overhead areas, it is established in underground mining for many years. Shotcrete is not only applied in pre-processing of the mines, but particularly of use for cut and fill, as well as room and pillar mining methods. There it is used to secure excavation chambers. When the mine face is secured with shotcrete and subsequently the mining continues, the applied shotcrete will automatically be mixed with the ore."

Jan 1, 2016

By Lloyd W. Trevoy

Titanium and zirconium heavy minerals occur in the tailings streams from processing plants which use the hot-water extraction process for recovery of bitumen from tar sand. In a research program conducted by Syncrude Canada Limited, the crude tailings stream was upgraded to produce quality zircon and titanium mineral products. To process the tailings through conventional upgrading equipment, bitumen residues must first be removed from the mineral grains. Then, by gravity separation, fines and coarse sand grains were removed and a 71% heavy minerals concentrate was prepared which was further separated by high-tension equipment into zircon and titanium minerals concentrates. The zircon concentrate was upgraded by gravity, magnetic and high-tension cleaning to produce a high-quality 98% zircon product. The titanium minerals concentrate was separated into rutile, leucoxene and ilmenite fractions. Heavy minerals distribution in tar sand drilling core samples has been evaluated for various locations on Syncrude Lease 17, and expected annual production levels of heavy minerals have been estimated. A preliminary evaluation has been made of the potential for zircon, leucoxene and rutile production and for further upgrading of ilmenite and leucoxene to synthetic rutile for titanium dioxide pigment production.

Jan 1, 1978

By E. Onal, C. Craddock, A. Chapman, M. R. Endsley

ABSTRACT Mining equipment operators must interpret and respond to complex information delivered by technology-centric rather than user-centric systems. The ability to achieve high situation awareness (SA) in the face of this data overload is a key challenge to effective decision-making and information exploitation. Incidents attributed to human error that compromise safety and result in loss of revenue, or even life, are often the result of system designs that overload human cognitive capabilities. This paper defines SA as it relates to the operation of mining equipment and describes the design and preliminary evaluation of a new electric shovel operator user interfa

Jan 1, 2013

By M. Rudolph, T. Leißner, TU Bergakademie Freiberg, C. Mämpel, R. Möckel, M. Embrechts, T. Leistner

Tin-mining activities have taken place in the region of the German Erzgebirge (Ore Mountains) for over hundreds of years up until 1991. For long times, gravity separation processes used to be the dominating beneficiation approach in those mining districts to recover cassiterite, the main tin-bearing mineral. For fine (< 100 µm) and very fine (< 20 µm) particles these approaches might not represent effective techniques, significant valuable materials could not be recovered and reported to tailings, where it was subsequently disposed. Thus, there are substantial amounts of cassiterite still present in these tailings disposals, most of it as very fine particles with already high degrees of liberation. That fact brings these tailings disposals into focus for potential reprocessing using beneficiation approaches, which are more sensitive to fine and very fine particles. In this paper we present results concerning the laboratory-scale treatment of material from exemplary heaps of the former Altenberg and Ehrenfriedersdorf mining sites using various flotation methods (including conventional froth flotation and oil-assisted flotation). Different size ranges of the material were previously prepared in order to investigate their response to the different techniques. For the study, special emphasis is put on agglomeration flotation, an oil-assisted flotation method. Therefore, an aliphatic oil phase of alkane basis is used to either selectively aggregate or collect the cassiterite particles. Recovery and flotation performance results are presented with respect to different process parameters: various collectors (including sulphosuccinamates and phosphonic acids) and depressants (including sodium fluorosilicate and oxalic acid) regime, oil dosage, agitation time and pulp density during oil/pulp agitation. Furthermore, the oil/particle aggregation behavior is analyzed via particle image analysis and, additionally, collector adsorption characteristics are investigated by contact angle measurements and zeta potential analysis. The data obtained is correlated with the testwork results achieved in order to interpret the flotation response of very fine cassiterite particles.

Jan 1, 2016

By G. P. van Greunen

"The rehabilitation of underground excavations has been undertaken as long as mining has existed. The conventional methods have proven to be dangerous, time consuming and expensive. During the construction of Styldrift Mine at Royal Bafokeng Platinum several vertical and horizontal excavations had to be rehabilitated. With a zero tolerance attitude towards working in unsafe conditions, together with a non-negotiable timeline to construct and ramp up the mine, the project team could not rehabilitate these excavations using conventional methods. This paper details the approach used to rehabilitate excavations using remote methods and how it was adapted to suit varying operating conditions and requirements - ensuring that no person ever entered an unsafe excavation before it was fully rehabilitated and safe. INTRODUCTION Styldrift Mine is an expansion project of the Royal Bafokeng Platinum group. It is located in South Africa in the North West Province some 10 km south of the Sun City resort (Figure 1). The mine consists of a twin shaft system (Main Shaft and Services Shaft). Capital construction of the shaft and associated infrastructure started in 2009 and is projected to be completed during 2020. The designed steady state production capacity of the shaft is 230 ktpm of Merensky ore. Production ramp-up commenced in 2017 with steady state production set to be achieved 36 months later in the fourth quarter 2020.Merensky Reef was intersected at a depth of 600 m below surface and the shaft design has a mean mining depth of 630 m. The project was approved for execution in 2008 on the basis of a suitable mine design and bankable feasibility study. One of the main excavations that required rehabilitation was an underground reef silo, Silo 4. It is a key piece of infrastructure on the critical path to allow steady state production at Styldrift Mine to be achieved. During construction excessive scaling within the silo along its 64m length necessitated urgent rehabilitation to be able to meet the ramp-up schedule. The criticality and urgency of these excavations prompted the project team to reduce the risk of failure while ensuring safe and cost-effective rehabilitation. This paper will focus on the rehabilitation of Silo 4 while capturing the essence of the learnings of all the excavations that were rehabilitated remotely."

Jan 1, 2019

By Paul L. Broughton

"IntroductionThe coal deposits, all of lignite rank, of economic interest in Saskatchewan are associated with the Ravenscrag Formation (Paleocene). Several Cretaceous formations have less significant lignite accumulations (Broughton, Irvine and W'hitaker, 1974). The Swan River Group (lower Cretaceous) and Judith River Formation (upper Cretaceous) have the only coalbearing strata in the shallow subsurface of central Saskatchewan. The Swan River Group coalfield is relatively small and underlies only 15 sq km of the surface approximately 40 km south of La Ronge, Saskatchewan. An estimated 36 billion short tons are within 45 m of the surface. No reserve estimates are known to have been calculated for the coal-bearing Judith River Formation exposed at the surface in the vicinity of the South Saskatchewan River valley in west-central Saskatchewan. Although no coalfields have been delineated, lignite beds up to 1.8 m thick have been intersected in test holes. The coal-bearing upper Cretaceous and lower Tertiary strata of the northern Williston Basin extends the full width of southern Saskatchewan for 650 km, and from the United States border 120 km north to 50° latitude (Fig. 1). Only the coalfields of the Ravenscrag Formation, because of their economic interest, will be considered further. There are four major coalfields. They are, from east to west: Estevan, Willow Bunch, Wood Mountain and Shaunavon (Cypress) coalfields. Cumulative lignite seam thickness for each basin is 10 -15 m (Figs. 2 and 3). The origin of each coal basin, resource calculations, seam stratigraphy, and mining activity are discussed. Regional Setting The Williston Basin is an ellipsoidal depression in the Precambrian basement, centered in western North Dakota and marginal to the exposed craton of northern Saskatchewan and central Manitoba (Fig. 1). The sediments of the basin range from Cambrian to Pleistocene in age and have a maximum known thickness of 4614 min western North Dakota. A maximum of 3200 m is recorded in southern Saskatchewan. Most structural deformation is late Cretaceous to early Tertiary (Paleocene) in age, coinciding with the Laramide Orogeny. The pre-Laramide Williston Basin, with a depocenter near Williston, North Dakota, began developing during the middle Ordovician, or possibly earlier."

Jan 1, 1985

By Liu Liu

In the recent 10 years the rapid development of Chinese steel industry has attracted the attention of the world. The technological progress of converter steelmaking has played an important role in this process. First of all, slag splashing has been extensively adopted by Chinese steel companies in various sizes of converters from largest to smallest ones, and even including those using special hot metal containing V and Ti. Remarkable metallurgical results have been achieved. Up to now the average converter campaign life has reached nearly 10,000 heats, and the longest exceeds 30,000 heats in three melt shops. Based on this process, the long-life combined-blowing converter steelmaking technology has been developed. Slag splashing has been used to form a gas permeable "slag mushroom" on the top of bottom nozzles to protect the nozzles. In order to keep the effective bottom blowing, furnace bottom thickness control technique has been developed to prevent the furnace bottom growth. It makes the service life of bottom nozzle the same as the converter campaign life (average 10,000 heats and longest > 30,000 heats). The complete combined blowing was ensured through out the furnace campaign. Concentration product [C][0] is in the range of 0.0023 ~ 0.0030%, the T.Fe in the slag is lowered by 4 ~ 6%, and the [0] in steel is decreased by 100 ~ 250 ppm.

Jan 1, 2004

By A. A. McCloskey

APPROXIMA TEL Y 95 percent of Waite-Amulet&apos;s Lower A orebody will be mined by diamond-drill stoping. This method of stoping was developed, and has been successfully applied, at the Noranda mine in recent years(1) and is now used in several base-metal and gold mines in north-western Quebec and in other parts of Canada, South Africa, and Australia. The purpose of this paper is to deal with the features of the Lower A ore-body which led&apos; to the adoption of this method of stoping, and in addition to give a general description of stope layout, stope development, main haulage development, chutes and grizzlies, diamond drilling for stope blasting, diamond drilling and equipment, primary blasting, secondary blasting, haulage and loading, ore pockets, pumping and drainage,. and shafts at Waite Amulet. Figure 1 is an isometric projection of the orebody, illustrating the mining system. The factors that led to the adoption of diamond-drill stoping of Lower A orebody are as follows: (1) Safety.0 (2) Size and shape of the orebody, and depth of the orebody below surface. (3) Strength of the hanging-wall, footwall, and sulphide ore. (4) Continuous ring-drilling from sub-level drifts, with no delay for blasting. (5) Large-tonnage blasts at the end of Saturday afternoon shift, after ali men are out of the mine. (6) Sub-levels may be retreated from top to bottom simultaneously, or lower sub-levels may be retreated first without any change in the ring-drilling la yout. (7) Large stopes up to 100 feet wide can be mined, leaving substantial pillars up to 60 feet in width, which may be partially recovered by âiamond~drill stoping or by other stoping methods. (8) A large tonnage may be drilled-off in advance of blasting, but only a supply of unoxidized ore for flotation treatment is blasted. (9) Better ventilation during working shifts. (10) Gravity flow of all broken ore to grizzlies located in the footwall of the orebody. (11) Electric blasting by a crew of two men.

Jan 1, 1941

By S P. Giambra

The 50,000-ton-per-day Concentrator and Crushing Plant, complete with its related water supply, tailings disposal and concentrate handling systems, was started up in a five-month period, with the entire plant obtaining its design capacity six months after the first mill became operational. Individual mill lines, with their spiral circuits, achieved design capacities within a week after the first treatment of ore through each mill. Construction and start-up proceeded together in many areas of the plant, and considerable organization and cooperation between the Owner, the Engineer and the Contractors permitted a smooth transition from construction to operation. PLANT DESCRIPTION THE Carol Lake Plant of the Iron Ore Company of Canada l1as been well described in various technical magazines. The purpose of this paper is to present a brief outline of the start-up of the con-centration complex. This start-up was accomplished in a period of five months, with the plant producing one million tons of concentrate and achieving its design-rated tonnage less than six months after the first ore was treated.

Jan 1, 1963

By K. G. Chipman

IN 1936, the Department of Mines and Resources was formed by the amalgamation of the former Departments of Mines, Interior, Indian Affairs, and Immigration. In the amalgamation, the Geological Survey and the Topographical Survey became the major divisions of the Bureau of Geology and Topography, which is a part of the Mines and Geology Branch which, in turn, is a part of the Department of Mines and Resources. The Topographical Survey was formed by combining the former Topographical Division of the Geological Survey and the air and ground mapping sections of the former Topographical and Air Survey Bureau of the Department of the Interior. The latter organization, previous to 1933, had been known as the Topographical Surveys Branch of the Department of the Interior. The amalgamation of 1936 definitely placed on the Topographical Survey the responsibility for the original mapping required for the development of our natural resources. The war has brought upon us the situation where all work has had to be in the furtherance of the war effort. With decreased staff and limited appropriations, the mapping on those scales which are directly concerned with the natural resources has been confined to the search for oil and strategic minerals. The reconstruction period will produce a different situation, with different problems. The past is behind us and it is necessary to prepare for the future. First, we should consider briefly a few general principles in the making and using of maps, then take stock of what we have, see what the needs are, and consider how we are to meet these needs.

Jan 1, 1944

By W J. Riva

This paper reviews the circumstances that led to the development and construction of a commercial-scale vertical shaft carbonizer at Conmore, Alberta. This form coking process may be regarded as having potential application in other areas. Coal pelletizing offers a promising method of decreasing coal agglomeration costs under certain circumstances. Pellets can be rolled easily from -35-mesh coal, provided that a minimum of -200-mesh coal is present. Bentonite was found to be the best binder and was most effective when added in amounts of about 2 per cent. The water content of the coal pellets was observed to vary from 18 to 23 per cent. As a by-product of this investigation, it seems possible that fine coal could be converted into stoker feed by this process. A short investigation of the effect of heating rate on the carbonization of pellets was conducted. The low maximum heating rates in certain temperature ranges, necessary to avoid crack formation in the pellets as reported by other

Jan 1, 1964

By L. M. Dwarkin

Introduction Avital factor in the success of any coal mining operation is the method of roof support employed. A coal seam in? place has been described as the filling in a geological sandwich and the process of mining as the art of snatching the filling from the midst of the sandwich. The difficulty of this task can be appreciated -in the realization of the tremendous weight bearing on a coal seam due to overlying strata; a weight that can exert pressures of several thousand pounds per square inch. Over the years that mining has been carried on, methods have been evolved by arduous trial and error, making possible the successful extraction of billions of tons of coal. However, these time-proven methods are not enough. The constant demand for faster and cheaper production, the necessity of mining under increasingly difficult conditions, and the requirement for higher standards of safety, call for ever better and more efficient roof support. A recent and very promising development in answer to this need is that of Roof Bolting. Roof Support in General Before proceeding to the subject proper, a brief discussion of the older roof support methods is of value in illuminating the difficulties involved and the problems to be solved.

Jan 1, 1951

By A. Lloyd, Montgomery, J. Jorgesen, W. J.

"Coals are ranked according to their degree of metamorphism or progressive change in the natural series from lignite to anthracite. The reader is referred to ASTM Standard D-388, ""Standard Classification of Coals by Rank"" for a detailed description of the system in use throughout North America including Canada.Fixed carbon and calorific value (expressed in Btu/ lb) calculated to the mineral-matter-free basis have been chosen as the main characteristics from which rank is established. Higher rank coals are classified according to fixed carbon content, lower rank coals according to the calorific value on a ""moist"" mineral-matter-free basis. Certain adjacent groups are differentiated according to their agglomerating (caking) properties. ""Moist"" refers to inherent moisture. Referring to Table 1, coals having calorific values greater than 14,000 Btu/lb on a moist mineral-matter-free basis and fixed carbon of 69% or more on a dry mineral-matter-free basis are classified according to fixed carbon. Coals having calorific values of less than 14,000 Btu/lb on a moist mineralmatter-free basis are classified according to calorific value on a moist mineral-matter-free basis. Agglomerating coals having 69 to 86% fixed carbon on the dry mineral-matter-free basis are classified in the low or medium volatile group of the bituminous class according to their volatile matter content. Agglomerating coals having calorific values between 10,500 and 11,500 Btu/lb are classified in the high volatile C bituminous coal group; nonagglomerating coals in the same calorific value range are classified in the sub-bituminous A coal group."

Jan 1, 1985

By Karl Hoover, Cassandra Spence, Brent Bachewich, Jaakko Levanaho

"Since year 2000 the gold recovery into copper concentrate at Hudson Bay Mining and Smelting has reduced considerably during the summer months. This initiated a testwork program in the fall 2003 to find reasons and solutions for such change. During the testwork mineralogical factors, water quality effects and different reagents were evaluated. The reason for the lower recovery appeared to be the sensitivity of some collectors to pulp temperature. As a result of the work different collectors are being used in the mill in the summer than in the winter. A modification to the water system was also made to provide cooler water to the mill in the summer months.INTRODUCTIONHudson Bay Mining and Smelting (HBMS) is located in Northern Manitoba, just on the border of Manitoba and Saskatchewan. The complex consist of four different mines, Callinan, Trout Lake, Konuto Lake and 777 mine including copper smelter and zinc hydrometallurgical plants producing metallic copper and zinc. Gold is a very important byproduct providing about 30% of the mine revenue. In early 1990s when the company was facing declining ore reserves and was starting to gradually close down the operations, the 777’th exploration drill hole discovered a new orebody, which initiated a $0.5 billion expansion program. The main projects were a new 777 hoist with underground development and a new zinc cell house. About $30 million was used to increase the mill throughput to the present 2.27 million tonnes or 2.5 million short tons per year. The expansion programs were finished by the end of the year 2003.Historically the gold recovery at HBMS has varied between 60 and 70%. The recovery has been somewhat lower during the summer months. Gold recovery improvement projects were conducted throughout the 1990s, but were not focused on the seasonal gold recovery variance. However, since 2000, when the water system modifications to meet the increased water demand were completed, the gold recovery during the summer has been much lower than in the past. In August 2003 gold recovery fell below 30%, which initiated a metallurgical research program to discover the reasons behind the low gold recovery in the summer."

Jan 1, 2005

By C. Pelley, S. Kelebek, T. Katsabanis, B. Nanthakumar

"As part of a larger investigation on generation of fines from mining activities and their effect on downstream operations, ore samples from Onaping area stockpiles of Falconbridge Ltd were studied. Batch flotation tests were conducted on the stockpile samples and fresh ore samples to explore the effect of stockpiling on grade-recovery performance. Head grade and particle size distribution of the samples from stockpiles were adjusted so that the samples compared are similar to each other. In additional tests, fresh ore samples were blended with stockpile samples at various percentages, representing 27.4, 50.2 and 81.5% of stockpile samples.The samples from stockpiles produced inferior nickel grade-recovery curves compared to fresh ore. The poorer grade-recovery performance was attributable to two factors. First, a significant dilution effect was observed due to the nearly complete flotation of pyrrhotite. Secondly, while pyrrhotite from stockpiled ore became highly floatable, the same stockpiling conditions caused nickel losses that were attributable to non-floatability of some pentlandite.In the case of blending, there was generally insignificant difference in the nickel grade-recovery between fresh and blended samples when the blending cases involved 27.4 and 50.2% stockpile samples. However, an increase in pyrrhotite recovery was observed for both blending cases. At 81.5% blending case, degraded grade-recovery was significant primarily due to the nearly complete flotation of pyrrhotite. There was a small, but noticeable amount of nickel loss for this case. However, for lower ratios of blending this loss was negligible.The increase in pyrrhotite recovery was partly attributed to its activation by Cu and Ni ions. Formation of a significant amount of elemental sulphur was also apparent from analysis of stockpiled samples. It can be concluded that pyrrhotite is mildly oxidized under stockpiling conditions while part of the pentlandite undergoes a more severe oxidation."

Jan 1, 2006

By W. N. B. Armstrong

CORROSION of metals, for the purpose of this talk, may be divided into two general classes, namely, atmospheric and chemical. Atmospheric corrosion is caused by the natural agents -water, air, salt, and temperature -as well as by the agents arising from industrial operations which pollute the atmosphere. Chemical corrosion affects metals in refineries and chemical plants where severe conditions exist due to .acids, alkalies, salts, solvents, gases, ?steam, etc. A special condition is encountered on road equipment and motor vehicles due to the large amounts of corrosive salts which are used on our roads in the winter. Exposure to corrosive conditions such as those referred to above causes metal to be destroyed and, therefore, it has to be protected. The non-metallic or organic coatings used to protect the metal are themselves destroyed ultimately by these same conditions. Since all types of organic coatings do not have the same kind and degree of resistance to degradation, a particular kind of -coating must be used for a particular set of conditions in order to obtain the maximum benefit. In ?addition to the above mentioned agents, organic coatings are degraded ?by sun-light, which is probably the severest single factor in the breakdown of organic coatings exposed outdoors. We can divide organic coatings, in a general way, into the following classes: (1) Conventional coatings, and (2) Special coatings.

Jan 1, 1958

By C. R. Fast, G. C. Howard

The loss of fluid to the formation adjacent a fracture governs the areal extent of the fracture and the success of hydraulic fracturing as a production stimulation technique. The three flow mechanisms which control this loss are the result of the viscosity of the fracturing fluid and the permeability of the formation to the fracturing fluid, its wall building properties, and the combined effects of viscosity and compressibility of the reservoir fluid. The effects of these flow mechanisms can be evaluated in terms of a fracturing fluid coefficient, the fundamental concepts of which are developed in the paper. The fracturing fluid coefficient, which may be used in calculating the areal extent of fracturing, affords a direct measure of the effectiveness of fracturing fluids. The area of hydraulically created fractures is in-creased as the coefficient is de-creased. The fifteen-fold variation noted in this coefficient for the commercially available fracturing fluids tested resulted in a six-fold difference m the calculated areal extent of the fracture system.

Jan 1, 1961

By Sanjiv Dhanjal

"Often mineralogy dictates the physical properties of a material rather than chemistry. This in turn affects how that material behaves in a process plant, and whether optimum conditions for refining one mineral are different to those for refining another. For example how does refining copper from chalcopyrite differ to refining copper from bornite?Minerals are naturally occurring inorganic solids that have a definite chemical composition and an ordered atomic (crystalline) structure. X-ray diffraction is a common and highly developed method to identify and quantify minerals. X-rays are fired onto a material and the mineral is identified by the angles where the diffracted X-rays are in phase.Most X-ray analyzers are laboratory based. A sample is prepared and analyzed by a detector that travels in an arc to collect the diffraction pattern. COSMA has a curved detector which picks up the complete x-ray pattern instantaneously. Therefore, material is collected and transported through the machine where is it is analyzed continuously.COSMA measures about 0.5 tons of material per day, while laboratory analyzers measure a few grams at a time. Real time data trends are produced allowing for improved process evaluation and automatic control. The COSMA on-line system has taken X-ray diffraction out of the laboratory into the field.There are a number of systems in operation in cement production. It is recognized that on-line mineral analysis has a role in many other processes. This paper presents the technology and invites further discussion should the technology be beneficial to members of the audience.INTRODUCTIONThis article describes COSMA, a system that provides direct and continuous on-line mineral analysis using X-ray diffraction in the field. While X-ray diffraction is a common technique used in mineral analysis, the time from sampling to analysis can be hours and plant operators typically do not get the data in time to control a process or respond to an upset. COSMA provides rapid measurement, analysis and feedback of data, in real time. This provides powerful information that can be used to optimize operation, thereby reducing costs and increasing quality."

Jan 1, 2009

By D. Roy Eccles

A multi-element geochemical response, with contrasts of up to 29 times background, was obtained in soil above the Mountain Lake Diatreme, northwestern Alberta. The overall geochemical signature is indicative of an ultramafic source; geochemical responses contain elevated concentrations of Co, Cr,O, Cu and Ni with the presence of high Ba, Ga, HI, PO,, Rb, Ta, Ti and light rare earth elements suggestive ofa kimberlite or lamproite body. The shape, or morphology, of the enzyme leach-based geochemical signature over the Mountain Lake Diatreme combines moderately strong to strong oxidation halos, or a rabbit's- ear geochemical profile, with a sharply-defined apical geochemical profile. Because some Alberta diatremes discovered to date form positive topographic highs, the resultant geochemical signature may express the soil development profile that forms directly on top of kimberlitic and lamproitic bodies. The enzyme leach technique, which has proven to be a useful tool in base metal, precious metal and petroleum exploration, may have a significant impact on exploration for kimberlite, lamproite and related rocks in Alberta by providing industry with a useful and cost effective tool to probe blind and/or buried anomalies identified by airborne and ground magnetic surveys in areas of glacial overburden.

Jan 1, 2001

By R. Grau

"After commissioning and start-up of the first 500m3 TankCell® flotation cell in 2014, the over 300m3 mechanical flotation cells have earned their place in large-scale flotation operations. These 500 to 630m3 cells, designed for projects with large throughputs, are proven to provide savings in project capital and operational expenditure through savings in foot print, energy consumption, and less equipment to install and maintain. Addition to savings in different phases of a project, these cells provides operational flexibility and has shown improvements in metallurgical performance. In this paper a case study from Kevitsa TankCell® e500 installation and Buenavista del Cobre TankCell® e630 installations will be given.INTRODUCTION After development (Grönstrand and Bourke, 2008), characterization (Morales et al. 2009; Yanez et al. 2009; Grönstrand at al. 2009), validation (Elgueta et al. 2009; Coleman and Dixon, 2010), and more than 350 industrial installations of the Outotec TankCell® e300 flotation cell, the well proven energy efficient TankCell® product family introduced the TankCell® e500 forced-air flotation cell late June 2012 (Outotec.com, 2012). The introduction of the 500 m3 flotation cell followed by introduction of a 630 m3 flotation cell, TankCell® e630, in October 2014 (Outotec.com, 2014). These large flotation cells are designed for projects with high throughputs where the number of cells needed for operation with smaller equipment would become large. The benefits of this size of flotation cells comes from the lower capital expenditures due to lower equipment costs, savings in plant footprint, less installation work with less auxiliary equipment, lower energy consumption, and less units per installation resulting in less components, spare parts and maintenance.The first TankCell® e500 was commissioned and taken into operation in October 2014 at FQML Kevitsa Cu-Ni-PGE concentrator, nowadays owned by New Boliden. The first TankCell e630 was taken into operation in January 2018 at GrupoMexico’s Buenavista del Cobre Cu-Mo concentrator. The start-ups of the first TankCell® e500 and TankCell® e630 followed with test work where the hydrodynamic performances of the cells were characterized and metallurgical performance studied. The results of the TankCell® e500 test work were presented in detail by Mattsson et al (2015a; 2015b) and TankCell® e630 by Grau et al. 2018. In this paper the metallurgical improvements achieved with the large cell installations will be presented."

Jan 1, 2019