Search Documents

By The Staff

THE object of the work was to increase the capacity of the plant and, if possible, to reduce costs of the actual unit grinding while doing so. The accompanying assays of an infra-sizer analysis of the cyanide tail (Table l) illustrate the problem in hand. The cyanide tail is a combination of two products, gangue and FeS2. The assay alters by virtue of a change in gold value due to grinding and the relative quantity of FeS2 in the sizes, which itself varies with the grind. The disposal tail is the residue after the cyanide tail is scavenged by flotation, most of the pyrite being removed for roasting. It presents a somewhat different problem, since grinding gangue is all gain, but -10 micron FeS2 does not float nearly as well as + 10 product. This results in compromise in the final size to be aimed at. Extra grinding has hardly any appreciable effect on the gold extraction from the FeS2. (See Milling Investigations Into the Ore as Occurring at the Lake Shore Mine; Trans. C.l.M.M., Vol. XXXIX, 1936).

Jan 1, 1940

By G. S. Farnham

Abstract This paper lists the interests of the Physical Metallurgy and Chemical Research laboratories of the Metallgesellschaft, which were visited by the authors, members of a group of Canadian investigators sent to Germany by the Department of Reconstruction in 1945. The Physical Metallurgy Research Laboratory The following information was obtained from Professor E. Schmid, Chief of the laboratories. It is understood that Dr. Schmid is a former Nazi and was to be removed from his post in November (1945). Aluminium Research The laboratories investigated the corrosion resistance of the high-strength aluminium-magnesium-zinc alloys. The same test procedure as used by V.L.W. was followed and Dr. Schmid co-operated closely with Dr. Brenner on this project. Intercrystalline corrosion was combatted by additions of chromium, titanium, or vanadium, and the work in this field parallels that of Dr. Brenner of V.L.W. * Dr. Schmid reports that Bollenrath and Siebert believe that corrosion difficulties with these alloys can be overcome to some extent by heat treatment. He himself was of opinion that the correct answer lay not only in correct alloying but also in correct heat treatment. The heat treatment involved either interrupted quenching or a change in quenching rate from a solution temperature of 500°C. The procedure is either a slower cooling from solution temperature or an interrupted cooling with a holding period at l50°C. Work had been done on piston alloys, the 11-13% Si, 1% Ni, 1% Cu, and 1% Mg being the favoured material. This is called Lo-Ex and is similar to Mahle 124 or KS1275.

Jan 1, 1946

By Dave Rose, Jacques McMullen

"The Detour Lake mine is located 200 km northeast of Timmins, Ontario, Canada.The mill processes a free milling gold ore using both a gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 tpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The Detour Lake mine has one of the largest gyratory crusher in the world (60"" x 113"") and over the years, many improvements have been made to this crusher with the result of improving plant throughput. This paper will present how choke feeding the gyratory crusher has been found to be one of the main influences on crusher product particle size and plant throughput. It will explain how the effect of choke feeding the gyratory was measured and from that, the various changes made to improve choke feeding of the gyratory crusher.IntroductionOre is hauled from the open pit mine and dumped directly into a single 60"" x 113"" primary gyratory crusher. The live capacity of both the feed and discharge hoppers of the gyratory crusher are designed for two (2) truck loads each, assuming a nominal payload of 300 tonnes per truck. The surge bin under the primary crusher feeds an apron feeder that controls the ore feed rate at approximately 4,200 tph onto a 227 metres long x 1.52 metres wide belt conveyor with a nominal capacity of 4,200 tph.The primary crusher is operated at an open side setting of 172 millimetres to produce a F80 feed to the secondary crushing circuit of 135 millimetres."

Jan 1, 2017

By T. Strong

"Selectively recovering pentlandite from high levels of pyrrhotite presents a technical and operational challenge. The liberation characteristics and also the chemical environment is critical to performing a successful separation. Reviewing the mineralogy to understand the characteristics of the ore and the plant flotation behavior is fundamental to designing a successful improvement program.At Savannah Nickel the challenges presented by a falling nickel price required a rethink of the flowsheet to improve the project economics through improving the concentrate grade and recoveries. Glencore Technology reviewed the plant performance and proposed and tested solutions to improve the grade performance of the concentrator with the support of the plant team. A pilot plant comprising a M20 IsamillTM followed by an L500/1 Jameson Cell was operated on various plant streams. In addition to the pilot plant, flotation surveys and a plant based laboratory program was used to supplement the plant understanding and within two weeks significant improvements were identified and demonstrated. The combination of the pilot operation and the plant based laboratory program was able to quickly demonstrate the improvements and test with equipment that is fully scaleable from pilot plant to full scale.IntroductionPanoramic Resources Limited is a Western Australian mining company formed in 2001 for the purpose of developing the Savannah Nickel Project in the East Kimberley region of Western Australia. Panoramic successfully commissioned the $65 million Savannah Project in late 2004. The process plant at Savannah comprises a single stage crusher, SAG mill, flotation, thickening and filtering stages to produce a bulk nickel, copper, cobalt concentrate. Metallurgical recoveries average 86-89% for nickel, 94-97% for copper and 89-92% for cobalt. The plant was originally designed for a throughput of 750,000 tonnes per annum, but has consistently outperformed the design specifications.Due to low nickel prices the Savannah Nickel mine and processing plant were placed into care and maintenance in May 2016. Prior to suspending production Glencore Technology was engaged to investigate options to improve the concentrate grade. With the discovery of Savannah North in 2014 and the Savannah North Scoping Study demonstrating LoM ~8 years and Mining Inventory of 6.07Mt @ 1.26% Ni, 0.64% Cu and 0.09% Co significant future potential exists. By completing pilot plant studies prior to shutting down, the plant engineering studies can be completed and the plant readied for restart by the time the nickel price improves."

Jan 1, 2017

By Iain Sommerville, Hugh Mountford, Dawid D. Smith, Claude Dube, Brett Hixson

JW Aluminum use lean and Six Sigma techniques to continuously improve their target of reliable, repeatable and reproducible (3R) manufacturing. Six Sigma’s second stage gate, known as "Measure" involves identification and qualifying appropriate measuring systems. Metal quality (inclusions) are known in the industry to be an important element in 3R casting. The measurement of inclusions at JW Aluminum historically depended on outside vendors. In order to establish real time inclusion measurement ability within JW Aluminum, inclusion measurement systems in the marketplace were investigated. The qualification of a MetalVision MV20/20 ultrasonic inclusion analyzer are discussed as well as the subsequent application of the system in melting and casting improvement projects.

Jan 1, 2015

By J. E. Shigley

The gemological properties that allow natural emeralds and blue sapphires to be distinguished from other gemstones are summarized in this paper. A variety of synthetic and laboratory-treated emeralds and blue sapphires are also encountered in the jewelry industry today. Gemologists distinguish these latter materials from their natural counterparts based primarily upon features seen with magnification, such as inclusions and/or growth zoning. In some cases, however, these observations and standard gem-testing methods are insufficient, and the use of non-destructive analytical methods, such as optical spectroscopy and chemical analysis, are required for positive identification. The commercial value of synthetic and treated gems are much less, and can be insignificant in comparison to that of an important untreated natural gemstone. Identification of synthetic and treated gem material is essential to maintaining integrity in the jewelry industry. Loss of consumer confidence in the gemstones sold at the jewelry counter could have a negative impact on the exploration and mining of natural emerald and blue sapphire.

Jan 1, 1998

By S. Rivard

"This paper demonstrates the selection of grinding circuit technology for a number of recent projects including discussion of the key drivers and the role of energy efficiency. Decreasing head grades combined with a strong and sustained increase in operating costs has forced miners to examine increased project size, increased equipment capacity and efficiency improvements in order to reduce their unit operating costs and improve overall project economics. Comminution energy consumption, safety and capital cost considerations play a critical role in the success of projects. This paper presents some key guidelines for a successful and cost effective comminution circuit design and includes a case study on three projects, outlining the issues and the drivers which led to the ultimate circuit selection and the critical role that energy efficiency played.IntroductionComminution circuits for minerals processing are selected based on their suitability and efficiency in reducing run-of-mine ore to the desired feed size for the downstream process. The input material (ore) properties and downstream process requirements are the key determinants and there are standard approaches for each circumstance.The minerals processing industry has been a fast adaptor of efficiency improvements based on increasing capacity of equipment (e.g. trucks, crushers, mills, pumps) but less successful in adapting radically new technologies that disrupt incumbent flowsheets or processes.The installed power of grinding mills has increased linearly over the past 25 years (Meka & Lane, 2010) and pumps and classification equipment have kept pace. The autogenous grinding (AG) and semi- autogenous grinding (SAG) mills displaced stage crushing as a dominant method of coarse rock breakage in many applications causing crusher manufactures to increase the capacity of cone crushers to meet the competitive demand.Examples of new comminution technology in the 20th and 21st centuries are the development and adoption of cyclone classification in the 1940s (Newtech, 2016), AG milling in the late 1950s, vertical grinding mills in the 1980s, high pressure grinding rolls (HPGRs) also in the 1980s and ultrafine milling technology in the 1990s (Meka & Lane, 2010)."

Jan 1, 2017

By Patrick Frenette

The Goldex Mine is an underground gold mine using a unique mining method where a single very large stope is being created. In order to maintain stability of the walls and roof of the stope which is 450m, 250m high and up to 120m thick, ore is left in the stope as long as possible and acts as backfill would do. At many occasions during the mining sequence, the walls will be exposed on height ranging from 30 meters up to 250 meters. A monitoring system comprising in-stope laser surveys, a seismic system and an array of extensometers and sloughmeters all remotely connected to surface is used to observe the shape and evolution of the stope. This paper will focus on the results obtained following some of the large blasts and on the long term monitoring of the stope.

May 1, 2011

By Adrian Daniel

"Dating back to 1934, Con Mine is located directly south to the city of Yellowknife in the NWT, Canada. With mill operations ceasing in 2004, a challenging surface remediation situation resulted which required the treatment of close to 40,000 m3 of Arsenic impacted material.Through much of the period of 1941 to 1970, Con Mine treated their refractory arsenopyrite ore through the use of an Edwards Heath roaster. With mounting environmental pressure and through Canadian governmental studies during 1950 to 1970, attention was directed to the Arsenic Trioxide material being collected by two Doyle scrubbers on the Con’s roaster stack. In 1970, the roaster was decommissioned leaving the resulting Arsenic material in two containment areas on surface.As a result of Con Mine entering into remediation in 2004, the Con’s autoclave, commissioned in 1992, was dedicated to the immobilization of high impacted Arsenic material through the combination of excess Iron under high temperature and oxygen overpressure. Examined, herein, is the history and chemistry of the Con Mine autoclave as well as the two stages of chemistry for the Water Treatment Plant used to remove arsenic, heavy metals and WAD cyanide from tailings water. Simplified capping plans of the tailing containment areas and a high arsenic impacted area are also presented.INTRODUCTION TO CON MINECon Mine (Con) is situated just south of the City of Yellowknife in the North West Territories (NWT) Canada and is bounded locally by Yellowknife Bay (North Extension of Great Slave Lake) to the east and Kam Lake to the west (Figure 6). The discovery of gold at Con was made in 1934 and mineral rights were acquired by Consolidated Mining and Smelting Limited (Cominco) and Falconbridge soon thereafter. Nerco Minerals Limited (Nerco) took control in 1986 and in 1993, was subsequently sold to, Miramar Mining Corporation which in turn was purchased by friendly takeover involving Newmont Mining in November 2007 as a result of acquiring the Miramar’s Hope Bay project. Con’s underground operations ceased in September 2003 and have since entered into the remediation of the site. The current surface lease holdings are about 340 Hectares (Table 1) which sits on top of the Archean-aged Yellowknife Greenstone Belt."

Jan 1, 2009

By Louis J. Cabri

"Mineralogical evaluation of ores containing platinum-group elements (PGE) is fraught with difficulties because of the low grades (often 1-3 g/t PGE), dispersal of PGE (usually as finegrained platinum-group minerals [PGM]), as well as occurring in solid solution in some base metal sulphides (BMS) such as pentlandite and pyrrhotite. Mineral processors not only need to know how the PGE are distributed, that is, their mineralogical distribution, but the grain sizes of the PGM, and especially the associated minerals.After obtaining a representative ground sample, common approaches include studying a large number of polished or polished thin sections, concentration of the PGM and sulphides by different gravity methods (e.g., heavy liquids, elutriation, micro-panning) and study of the produced concentrates. Unfortunately, these methods often do not produce concentrations that are sufficiently representative of a particular ore. The newly developed patented technology of hydroseparation (Rudashevsky et al., 2002) is especially effective at making concentrations of PGM over a wide range of concentrations (down to <300 ppb Pt+Pd+Au) and size fractions, including <45µm (down to a few micrometres in size), a size range not possible by other techniques. This water-based environmentally friendly laboratory technique provides a large amount of data from samples, which can range from 5 to 1000g, giving confidence to extrapolation of results to bench-scale and larger test work, especially when combined with quantitative image analysis to determine modal percent of major minerals and mineral liberation data, needed to predict the minimum (K80) and optimum (K40) grinds. INTRODUCTIONThe invention of the electron microprobe in the early 1960’s and scanning electron microscopes (SEM) with energy dispersive spectrometers (EDS) in the 1970’s presented mineralogists with powerful tools permitting them to obtain chemical and surface area data on minute amounts of minerals in situ, in a non-destructive manner. An area of process mineralogy that has very much benefited from this new technology was the characterization and understanding of PGM species, resulting in rapid growth of newly characterized species (Figure 1). Recognition of the first PGM may be ascribed to the Spanish explorer Ulloa in 1748, who described native platinum from South America. The second PGM (laurite, RuS2) was only recognised in 1866 by Wöhler in placer samples from Borneo (now Kalimantan) and the third (sperrylite, PtAs2) by Wells in 1889 from the Sudbury Ni-Cu sulphide deposits. The discovery of the important Pt-Pd deposits in the Bushveld Igneous Complex led to the characterization of the important Pt-Pd sulphides (cooperite, PtS2 in 1928 and braggite, (Pt,Pd)S2 in 1932). By the early 1960’s, only about 20 PGM were recognised, and many later proved to be poorly or incompletely characterized. Thus, the introduction of electron probe microanalysis (EPMA) led to a 50% increase of known PGM, as shown in a 1972 review on PGM (Cabri, 1972). At the time of the next review in 1981 (Cabri, 1981) the number of known PGM had grown to 75 and as of 2002, it had increased to 109 (Cabri, 2002). However, it is the author’s experience that less than about 25 PGM may be considered to be “common”, i.e., found in many different deposit types, as shown in Table 1, but usually only some of these occur in any one particular deposit."

Jan 1, 2004

By V. K. Alves, P. Lacoste-Bouchet

"In order to improve ball milling efficiency in pellet plants, Companhia Vale de Rio Doce (CVRD), experiments new technologies in Santa Luzia (M.G. – Brazil) research center facility. Pilot grinding tests have been conducted with small grinding media, size distributed from 5 to 12 mm (millpebs). Tests have been conducted on an ore from CVRD’s Usina 5 Nibrasco, in Vitória, Brazil. A sample of the regrind circuit feed was obtained and used in comparative grinding tests with two types of grinding charges: 100% balls and a blend of 70% balls and 30% millpebs by weight. According to the balls charge, the grinding media mixture has showed the following benefits: reduction of the power draw, increase of the mill capacity, reduction of the circulating load and a slight increase of the ore blaine. Following the results obtained, CVRD is going to further explore the regrinding potential of millpebs.INTRODUCTIONCompanhnia Vale de Rio Doce (CVRD) is the largest mining company in Brazil. CVRD is involved in iron, base metals, gold and bauxite industries. Moreover, CVRD operates several pelletizing plants in Brazil and in other countries.CVRD’s Center for Mineral Development (CDM) is equipped with a comminution laboratory where studies are carried out that are aimed at the optimization of existing plants at several mining sites as well as the technical and economical feasibility of new projects. The laboratory is equipped with a complete pilot plant with several mills and classifiers, enabling continuous grinding tests in grinding circuits of almost any capacity and characteristics.In January 2004, CVRD undertook to conduct pilot tests at CDM for evaluating the effect of small grinding media on ball milling efficiency. Generally speaking, it is not unusual for operators to add oversize grinding media in a conventional regrind mill. This fact originates mainly from prohibitive prices of grinding media below 25 mm due to a production capacity decrease of grinding media producers. The size of the grinding media is an important variable affecting ball milling efficiency. Use of oversize balls decreases the number of contact surface between which particles can be caught and broken."

Jan 1, 2005

By J. F. Archibald

A research effort has been undertaken, under Workplace Safety and Insurance Board of Ontario (WSIB) sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials [thin, spray-on liners (TSLs)], typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and bolt-and-mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field-scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen’s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validate that thin, spray-on linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

Jan 1, 2004

By J. A. Finch, J. Vergouw

"Flotation selectivity becomes progressively more difficult to achieve with decreasing particle size. One of the possible problems is agglomeration, i.e. particles clustering together. One mechanism derives from the surface charge all particles develop in water. Agglomeration driven by surface charge is known as coagulation. One form is coagulation between particles of two different minerals of opposite charge. Another is coagulation between particles of the same mineral when conditions are such that the charge approaches zero.The paper describes the method of measuring charge and a new automated settling technique for measuring agglomeration. The phenomena are illustrated with galena and pyrite. Methods of assessing the importance of agglomeration in the plant environment are still to be developed.IntroductionFine particles can agglomerate (i.e. adhere to each other) under certain conditions. This is counter-productive for any physical separation process, including flotation. One cause of agglomeration derives from the surface charge that all particles develop in water. Agglomeration due to surface charge effects is referred to as coagulation. There are two forms of coagulation. If the surface charge is brought to near zero then the force of repulsion is lost and particles coagulate. This usually applies to particles of one mineral type and the technical tenn is homocoagulation. On the other hand, if two particles have opposite charge there is an attractive force. Since the particles in this case are usually different minerals this is known as heterocoagulation.Both types of coagulation can cause minerals to be misplaced. In the case of heterocoagulation this is fairly obvious. One example that may be familiar is slime coating (fines of one mineral coating larger particles of another) But even homocoagulation can be a problem an agglomerate of the same mineral particles can entrap particles of another mineral."

Jan 1, 1997

By Simon D. Handelsman

?Artisanalmining ?Application of human energy (e.g. pick & shovel) directly to produce minerals ?majority no technical skills and lack adequate working tools ?Small-scale mining ?Application of modern technology for limited scale mineral production Significance of ArtisanalMining ?15 million people in artisanaland small scale gold mining ?55 developing countries ?Use of mercury damages health of 100 million people

May 1, 2006

By H. Brodie Hicks

"THE REVIVAL of the Mayo mining camp, with particular reference to the activities of United Keno Hill Mines, Limited, has been one •of the more spectacular and also one of the most important of the post-war developments in the Canadian mining field. The geological location of the camp, coupled with other natural disadvantages, have in the past limited the mining area to small-scale, highgrading operations, but the post-war improvement in metal prices has now broadened the possibilities and has led to the considerable success achieved by United Keno Hill Mines, Limited, and the present boom-type development by a whole host of newcomers to the field.LocationYukon which has an area of 207,000 square miles, is showing ever increasing possibilities as a mineral source of great value and more and more attention is being focussed on the Territory. The accompanying generalized map (Figure 1) shows the main transportation routes and mining districts.The Mayo Mining District comprises roughly the eastern two thirds of Yukon Territory lying north of McMillan river and south of the Peel. The district was one of the first in the Territory in which placer gold was discovered, but the occurrences proved of minor importance. Other minerals reported include ores of tungsten, tin, antimony, and several other metals, but of primary importance have been the ores containing silver-lead-zinc-cadmium now being developed and mined in the Keno area. Similar ores have been found over a very considerable area, extending some 50 miles north, 15 miles east, 30 miles west, and 10 miles south of the townsite of Keno Hills, Keno City, a total area of 2,700 square miles."

Jan 1, 1952

By Tim Hughes, A. H. (Sandy) Gray, Jennifer Abols

"The selective recovery of gold and silver from solutions containing other metals such as copper is possible using AuRIX®100 resin in conjunction with the Gekko Resin Column. Selectivity is driven by controlling the solution pH, which enables activities such as loading copper, gold and silver and then selectively stripping copper before gold and silver. Alternatively gold and silver can be loaded and the copper left in solution. The selective loading of gold while reducing the silver loading has also been demonstrated opening the possibility of producing high grade gold doré from high grade silver pregnant leach solutions. This paper reviews the AuRIX®100 resin and Gekko Resin Column Technologies, discusses the uses of AuRIX®100 in the recovery of gold and silver and the chemistry relating to several projects for which AuRIX®100 is being tested.INTRODUCTIONGekko SystemsGekko Systems specializes in the design, development and distribution of innovative mineral processing equipment and systems with a particular focus on gravity separation for the gold and diamond industries. The company, which has been around since 1996, has five main products: the InLine Pressure Jig, the InLine Spinner, the InLine Leach Reactor (ILR), Gekko Resin Column and Modular Systems.The InLine Leach Reactor is an intensive cyanidation reactor that uses high cyanide (0.5 – 2 % NaCN) and high oxidant (20 ppm dissolved oxygen as O2 or hydrogen peroxide) to dissolve gold from medium and high-grade gravity or flotation concentrates. The ILR, which typically replaces a shaking table in the gold room, is available in both batch and continuous models. There are 42 installations worldwide. Further details on this technology can be found in papers written by Gray et al (2003) and Longley, McCallum and Katsikaros (2003). By replacing a shaking table with an ILR, the overall gravity and plant recoveries can be increased significantly. Other advantages include reduced security risks, lower operating costs, reduced operator involvement due to the automatic process and increased safety for gold room operators."

Jan 1, 2006

By C. M. Anson

This paper describes the progresses used in the manufacture of steel wheel-centres, tyres and axles at the works of the Commonwealth Steel Products Co., Newcastle, N.S.W., Australia. The plant is adjacent to the Northern railway and consists of three main buildings, namely: the foundry, the forging and rolling shop, and the machine shop. The foundry contains a 6-ton Heroult electric furnace, together with all necessary mechanical appliances for moulding. Reheating furnaces, steam hammers and tyre rolling mill are installed in the forging shop. The machine shop contains lathes, boring machines, and hydraulic presses. Until this plant commenced operations all wheels used in Australia were imported, previ.ous to the war, from England and Germany, and latterly from England only. Besides being of great benefit to the country in that there is now a domestic source of supply of these articles, there is also the advantage of retaining the home market; and in addition, a small portion of the population are now engaged in highly technical occupations requiring a great degree of skill. The plant began to operate in October 1919, and by 1921 was in a fair way to meet the domestic demand for those articles of railroad equipment which it manufactures.

Jan 1, 1925

By Dominic Fragomeni

"The mineral processing industry has had a long history of innovation that is recognized but not often celebrated. These include significant advances in mineral measurement, testing, comminution, mineral separation and process control technologies that have transformed mineral assemblages into ore.This presentation presents some of the major mineral processing innovations and the impact they have had on our industry. As we look to the future, it is critical that we innovate and change. We will explore some examples of the next developments and how they can be catalyzed in the face of risk management, lower metal price cycles, resource constraints, inertia and the challenge of short term value delivery."

Jan 1, 2017

By M. C. Pietrobon

"A common problem in assessing the applicability of laboratory flotation data is determining how closely conditions during laboratory testing of the ore matches those that occur in a plant. Typical laboratory based investigations do not consider factors such as water quality, pulp temperature and the pulp chemical environment during both grinding and conditioning on laboratory flotation performance. Disregarding these important factors may seriously compromise the validity of conclusions based solely on laboratory experimental results. Furthermore, considering these factors during the flowsheet design stage in the development of new ore resources may reduce financial risk associated with building a new plant. A methodology is described here which embraces these factors in an attempt to bridge the gap between laboratory and plant. The methodology should be considered a vital first step in all laboratory based experimental programs and has implications for fundamental studies on the flotation behaviour of single minerals. This methodology increases the confidence with which findings of laboratory based studies can be transferred to the plant and highlights the effect of variables which may be accessible to manipulation in the plant.Pulp chemical parameters, such as pulp dissolved oxygen demand, pH, Eh, mineral oxidation and solution composition were manipulated in the laboratory by adjusting the duration of gas purging after grinding, the process water input and pulp temperature. A key finding was that matching of the laboratory pulp chemistry to the plant pulp chemistry was dependent upon oxidation after grinding. In turn, mineral oxidation was dependent upon the pH in grinding, water composition and the duration of oxygen purging after grinding. The methodology closely matched the dissolved oxygen demand and surface chemistry of laboratory and plant pulps."

Jan 1, 2002

By Alfred W. G. Wilson

THE state of development of its iron and steel industries serves as a 1eading index to the general condition of a nation&apos;s business affairs. In this paper, the authors present an economic study of the progress of this group of industries in Canada for the decade 1927-1936. The statistical data and most of the tables which accompany this article have been com-piled by John Casey, Statistician, Bureau of Mines; the text and some of the computations have been prepared by the seni0r author. The principal source of statistical information has been the publications of the Dominion Bureau of Statistics; where other sources have been consulted, they are noted in the text. All weights are given in short tons. Records for the years 1913 and 1918 are also presented in the group of tables dealing with iron ore and pig iron; they will serve as a basis for comparison with nearly normal years in the two decades prior to 1927-36, which included the abnorma1 years of the Great War. GENERAL REVIEW At the beginning of the decade under review, this group of industries had returned to almost normal production, as determined by pre-war conditions. Iron ore consumption showed a steady increase between 1927 and 1930; a marked decline began in 1930 and reached its culmination in 1932, when the recorded consumption of ore was 293,353 to11s, about 16 per cent of the average consumption during the first four years of the decade; the last four years of the decade show a gradual increase in consumption; the amount of ore used in 1936 was still slightly below the amount used ten years before, in 1927 (see Table 1, top).

Jan 1, 1938