Search Documents

With the proving of a mineable orebody at Orlando in May 1961, Peko Mines N.L. was faced with the decision of whether to mill the ore on site or to haul it 25 miles to central facilities at Peko. Orlando was a relatively small orebody, so that it was decided to haul, although no reliable assessment of possible ore haulage costs was available.The necessity for a good haul road was recognised from the beginning and a 17 mile, 12 ft wide, single seal bitumen road was constructed, to link the mine to the Stuart Highway and Peko. The initial selection of 20 ton capacity diesel-powered end-tipping ore carts was made, with the best information available at the time.Since then some 130,000 tons of ore have been carted over a period of 3 years, and this paper presents the experiences of this haulage operation and the lessons learned.A second mine has just been brought into operation at Ivanhoe, 19 miles from Peko. For this haul it was decided to use an ore haulage vehicle of the side tipping road train type, which would cart some 70 tons, or more than three times the load of the vehicles initially selected.Only about 5,000 tons had been hauled at the date of this paper, but preliminary figures indicate a cost 01 1· 65d./ton-mile as against 2·47d. for the smaller vehicles.It would appear that the road haulage of ore from small outlying mines to a central plant can be highly economical, if certain basic rules concerning haul roads and vehicle selection are followed. This paper does not try to determine the maximum tonnages and haul distances which would finally make road hauling uneconomical...

Jan 1, 1966

By E C. F Hamman

Sunrise Dam Gold Mine is a large open pit mine 730 km NE of Perth, Western Australia. Contract mining commenced in the open pit in September 1996 in lake clays and saprolites with the first fresh rock mined late 1999, and the underground starting the first decline in October 2003. By May 2007, over 150 million cubic metres of material had been mined and the pit was 360 m deep with 80 m remaining before reaching the planned final depth in early 2008. A final cut-back in the northwest will commence in late 2007 with open pit mining in the Mega Pit expected to conclude in late 2010. The challenges of developing the pit can be divided into three phases:Soft materials û mining was in multiple staged pits and cut-backs in lake clays, saprolites, weathered material. The varying characteristics had a significant impact on mining methods and slope stability. Structural û mining was gradually exposing more fresh rock and the drive was to understand how major structures and lithological contacts impact on local and large-scale stability. This had a significant influence on mine design and scheduling. Slope angles û achieving the final slope angle is critical. This is done through application of high standards of final wall establishment and proactive geotechnical hazard identification and management. This includes dealing with the rapid rate of descent, interaction with underground excavations and managing rock fall risk. The paper discusses each of these phases, highlighting the geotechnical controls implemented to date, looking at their success and impact on mining.

Jan 1, 2007

By A Kurniawan, A Sjadat and M Akhasyah

PT Freeport Indonesia’s Deep Ore Zone (DOZ) is a block cave mining operation that has been in production for 15 years. DOZ is located approximately 900 m below surface and has an average production rate of more than 5000 t/d. The footprint of the extraction level will ultimately be 900 m long and average more than 200 m wide. The undercut level is located 20 m above the extraction level.While developing Panel 1K on the northern portion of the extraction level, a major geotechnical problem was encountered when there was a change in lithology and an associated fault intersection. A large collapse of the hanging wall of the extraction level drifts occurred in the area of the fault intersection between February and March 2011. This was followed by a collapse of one of the undercut level drifts directly above the extraction level in May 2011.It was suggested that the best approach to mitigate risk during rehabilitation was to systematically open up the failed area under the protection of a steel set support system. To achieve this, approximately 60 t of grout was injected from the undercut level to fill the voids created when the rock mass between the two levels failed. A ground penetrating radar system was used to survey the condition of the rock mass between the two levels before and after the injection of grout. After the grout injection phase was completed to a satisfactory level of confidence, rehabilitation activities started on the extraction level by taking out the now consolidated material from inside the drift in 2 m advances from under steel sets initially constructed in secured ground.Controlled blasting was the key aspect to the success of the initiative to open up just enough of the drift to systematically support the rock mass before the next set was installed. The systematic support consisted of in-cycle shotcrete sprayed over mesh pinned to the exposed rock, as effectively as possible, with splitsets before spiling the next advance’s protection canopy with rebar. Once secure, a combination of steel set and pumped concrete was installed as the final support. This final support provided a safe platform to repeat the process until the failed zone was safely traversed.CITATION:Kurniawan, A, Sjadat, A and Akhasyah, M, 2016. Rehabilitation of the collapsed panel 1K north in the Deep Ore Zone block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 763–768 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By X Feng, X Zhang, W Sun, Y Zhe, K Hou, B Zhao, H Liu

Pulang Copper Mine, being China's largest newly built mine using block caving, boasts an annual production capacity of 12.5 million tons. Production level and roadway stability hold the key to the successful application of block caving. However, with Tong Kuangyu being the only mine in China which has applied such a method, we currently lack relevant experience in the successful application of the method. This paper has studied the influence of different rock mass zonings, fault thickness, fault dip angles, on-site construction quality on the production level, roadway stability of block caving through numerical simulation and analysed the roadway stability in different kinds of support solutions so as to ensure the successful application of block caving in Pulang Copper Mine. The results have shown that the existing support method in Pulang Copper Mine can meet the requirement of roadway support in zone II and III, but could not satisfy the demand in terms of support strength in the relatively fragmented zone I area. When roadway passes through the fault, the deformation of surrounding rock and plastic zone of roadway will gradually decrease with the increase of fault dip angle; the deformation of surrounding rock and plastic zone of roadway will gradually increase with the increase of fault thickness. An ideal support effect can be achieved through the joint support of grouting and bolting when roadway passes through the fault. In the measured model of on-site construction, there is stress concentration in the intersection between the access and transverse drift of ore removal. Therefore, the stability of the roadway can be improved by improving the construction quality. CITATION:Sun, W, Hou, K, Zhang, X, Feng, X, Liu, H, Zhe, Y and Zhao, B, 2018. Research on supporting technology for production level roadways of block caving in Pulang Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 95–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Goldfields (Tasmania) Limited operates a small, high-grade underground gold mine on the West Coast of Tasmania, 30 kilometres north of Queenstown. The main orebody, Zone 96, was discovered in 1989, with major development work commencing in 1993. The mine was officially opened in July, 1996. Initial production came from a shallow orebody known as the Sill Zone, some 50 - 150 m below surface, which was accessed by a 1 in 8 decline. Zone 96 lies between 350 m and 550 m below the surface and is accessed by a 402 m deep, 3.2 m diameter internal shaft from the collar level located 100 m below surface. The main ore extraction system in Zone 96 is mechanised cut and fill, using high density paste fill. Run of mine ore and waste are hoisted in a single 5.5 tonne overturning skip, then trucked from the underground collar to the gold plant ROM pad or waste dump, respectively. Ground conditions in the mine vary with orientation and proximity to major faults. The gold is contained in a sequence of strongly altered volcanic rocks adjacent to the Henty Fault. Most of the gold is contained in massive quartz, ranging in width from 0.5 m to 7 m, which has been subjected to substantial faulting. Average mineable grade is about 27 grams gold per tonne. Ore reserves in 1996 proved an initial mine life of approximately 4.5 years at 90 000 ounces gold per annum, with significant potential for additional resources from extensions to Zone 96 and adjacent zones. The lease is located in an environmentally sensitive area and a very high standard of environmental management is an essential part of the operation. This paper describes the relevant aspects of mining at Henty including grade control, ground support, backfill placement and environmental management.

Jan 1, 1998

By D Lalor, N Goodman

The increasing demand for batteries is resulting in the development of large-scale projects for the production of key battery metals such as nickel and vanadium. Several of these projects plan to extract the battery metals from the ore via chemical roasting, leaving large volumes of waste iron oxides after fuming and/or leaching of the battery metals. These iron oxide wastes can be smelted in a HIsmelt furnace using biochar as the reductant, to produce clean, green pig iron with net zero carbon emissions. This green pig iron can then be added to basic oxygen or electric arc steelmaking furnaces to produce green, net zero carbon, steel. This paper describes the flow sheets and the economics for potential projects producing green pig iron via HIsmelt using waste iron oxides from nickel and vanadium production plants.

Sep 18, 2023

By K A. Bunker, A D. Campbell, E Ah Mu, A R. Penney

The Ernest Henry mine is a transverse sublevel cave (SLC), which is relatively unique due to the 45 degree inclination of the orebody. To economically recover ore, each sublevel is horizontally offset from the previous level by around 25 m, depending on the orebody geometry. Mine development, slotting and initial production within this zone occurs in a high stress abutment that increases in magnitude at depth. These areas are seismically active and close to the hanging wall where cave propagation is yet to initiate. High stress conditions and the close proximity to the cave seismogenic zone results in challenging geotechnical conditions in the step out zone of each level and requires management of hazards including stress driven rockfalls, rock bursts and pillar failure.This paper outlines how these hazards were forecast using numerical modelling and geotechnical monitoring. Risk management techniques included dynamic ground support design, development of a new mine layout and extraction sequence as well as delayed re-entry into seismically active areas. Ongoing monitoring, instrumentation measurements and field observations were used to track the effectiveness of the controls.Future production levels are forecast to experience increasing stress and seismicity, which will increase demand on excavations and installed ground support. Ensuring the techniques and controls for monitoring, measuring and mitigating stress and seismic hazards are enforced is essential for continued safe production.CITATION:Campbell, A D, Bunker, K A, Ah Mu, E and Penney, A R, 2016. Managing stress and seismicity in an inclined sublevel cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 319–328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Haukka M. T

A new low-dilution fusion method which has been successfully used for accurate determination of the major oxide components of silicate rocks, is applicable to rapid, accurate determination of trace or minor eiements in mineral exploration samples. Limit of detection is in many cases less than 5 ppm. Either rapid, approximate measurement and calculation methods (suitable for geochemical exploration), or more accurate methods (applicable to orebody evaluation studies) may be used.Rapid methods are described for nickel in rocks and sulphides containing 10 ppm to >2 per cent Ni, and for gallium. The rarely-determined element gallium is an example of a constituent which may be easily investigatedby XRF using the LiB02 fusion disc, which is a permanent, easily-stored analytical sample available for later rapid or accurate analyses. The method is applicable to over 30 elements at levels encountered in mineral exploration.

Jan 1, 1978

By J Seppelt, B Akerstrom, J Bubnich, D Seaman, T Waters

The Cadia Hill concentrator at Newcrest’s Cadia Operations has undergone several modifications and upgrades to treat an increased throughput rate of harder ore from the Cadia East block cave mine.Subsequent to the commissioning of the expanded circuit, the flotation cleaner block has undergone a systematic optimisation programme tackling all facets of circuit operation. This included debottlenecking circuit constraints and installation of Jameson cell technology to enhance copper and gold recovery while rejecting fluorine and gangue from the concentrate.This paper outlines the improvements over the course of the project and results obtained from the implemented actions.CITATION:Akerstrom, B, Seppelt, J, Waters, T, Bubnich, J and Seaman, D, 2018. Cleaner circuit optimisation at Cadia Operations, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 457–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Some Otago quartz veins display spectacular open-space filling textures indicative of shallow formation. Fluid inclusions in some such veins show that fluid immiscibility occured before or during mineral deposition. This immiscibility or 'boiling' occured at depths ranging from about 3 km to within as little as about 100 metres of the paleo-surface. Temperatures of mineralization range from 190 - 250¦C. Metals deposited in these veins include: Au(+Ag), Hg, Sb and As. Hydrothermal alteration is confined to minor silicifation of immediate wall-rock schist, less than about two metres from the veins. These veins have some similarities to classical epithermal systems elsewhere in the world, although wall-rock alteration is much less developed in Otago. From analogy to these classical epithermal systems, it is speculated that gold mineralisation may be found beneath Otago stibnite and cinnabar localities.

Jan 1, 1987

By L Snyman, S Webster and J Samosir

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant, which produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment and recover the ore.The E48 extraction level is located approximately 581 m below surface and consists of ten extraction drives and 214 drawpoints. Several stress measurements carried out at various levels in both E26 and E48 indicated a low underground regional stress environment and a low to moderate stress state in the E48 orebody. The E48 block used a post undercut strategy that was initiated in 2009, with production commencing in September 2010 and cave-through to the surface occurring approximately four months later in January 2011. Changes to the cut-off grade and fixed prices meant that Northparkes was able to develop an additional two drives to the north of the existing cave and one additional drive to the south. Modelling of the cavability of the additional drives indicated that the cave would not readily propagate to sufficient height of draw to mobilise the ore and tended to arch over to the existing cave shape. Based on modelling and a desire to reduce the risk of the project, preconditioning was adopted. Along with the requirement of safely hydrofracturing an active cave, a measure of the success of the preconditioning was desired. Few block cave operations have developed extension drives adjacent to existing caves.This paper summarises the lessons learnt from the development of this extension project, with a specific focus on ground control and monitoring.CITATION:Snyman, L, Webster, S and Samosir, J, 2016. E48 cave extension at Northparkes, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 111–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Application of the Anaconda Simplified Work Index for Multiple Test Sizes Vale uses Bond Work Index measurements extensively in a number of applications. The Bond Work Index is usually a good parameter for checking scale up procedures when sizing ball mills, as well as the basis for variability analysis whenever drill core data is available. It is typical to measure between 100 and 150 Bond Work Indexes, depending on the deposit characteristics. The Bond procedure is relatively complex and time costly. It also requires relatively large amounts of sample, which are very expensive to be obtained. The benefits of the Anaconda simplified procedure are: considerably smaller sample requirements and laboratory time. This makes it very much attractive at Vale's development centre, including geometallurgical mapping, operation efficiency control, mine to mill, etc. The Anaconda simplified procedure was implemented and evaluated at Vale's Development Centre using a number of ores and several samples of each ore totalling more than 190 measurements. The Anaconda simplified method was calibrated for several test sieves and a correlation for any test size was determined for Vale's test mill. The calibration was also extended for two sample top sizes. The relative error of the simplified procedure was found to be in the range of nine per cent which is within the expected error Bond standard procedure. The implementation of the Anaconda method at Vale's development center has been used with great success over the past years in several green field, brown field projects and operating plants.

Sep 13, 2010

By T Ireland

The Project Hobson tunnel excavation was the first use in New Zealand of an earth pressure balance (EPB) tunnel boring machine (TBM). The tunnelling on the project was very successful and break-through was achieved three weeks ahead of program, demonstrating that tunnelling can be undertaken in Auckland with a high degree of cost certainty.Project Hobson involved the replacement of an existing 90 year old above ground sewer that crosses Hobson Bay in Auckland, New Zealand, and which had reached the end of its economic life, with a 3 km long, 3.7 m internal diameter segmentally lined bored tunnel. The NZD$ 118 M project has provided several environmental benefi ts to the Owner, Watercare Services Ltd and the local community:· provide capacity to meet projected growth in the region,· virtually eliminate wastewater overflows into Hobson Bay and the Waitemata Harbour, and· remove an obtrusive visual feature and open up the bay for recreational purposes.Auckland’s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20 km of the city centre.The paper describes the design and construction challenges for the projects, including TBM performance, ‘sticky spoil’ management, and risks associated with basalt lava flows and two paleovalleys. The paper also highlights the reasons for the success of the project, including a rigorous approach to risk management during design, and effective planning during construction. Other useful data such as the effect on the watertable caused by closed face tunnelling, and ‘faceloss’ estimates derived from settlement arrays are included in the paper.Project Hobson also saw the successful implementation of a Geotechnical Baseline Report – one of the first uses of this type of document in Australasia.

Mar 8, 2011

GOLD has played a part in the development of Australia. The total yield exceeds SIX hundred million pounds sterling, while the glamour of gold-mining and the unfailing demand for the product have enhanced its influence. The production is still considerable, but the yield is less than one-quarter of that twenty years previously, while the number of men employed has dropped from 70,000 to 11,000. Not only has there been a marked decline in production, but it is anticipated that thisdecline will continue, and continue more markedly. It is therefore desirable to ascertain the causes of the decline and inquire into means for diminishing or preventing it.The problem under discussion is far from being only local. Finlay states: The grand feature of the history of the business has been the progress of an economic cycle unfavourable to gold milling. The USA yield fell from $101,000,000 to $44,000,000.South Afriea has for some time produced one-half of the world's gold; yet in the Mining and Scientific Press of 11th February, IH22, General Smuts is quoted as saying that if the premium disappeared entirely 24 out of 34 mines would shut down. The solution, however, might be either general eg, a great advance in the metallurgy of gold; or local eg, a bonus; but before discussing any of the proposed solutions it will be advantageous to review the situation.STATISTICS OF THE PAST AND PRESENT PRODUCTION OF THE WORLD AND OF AUSTRALIAThe inquirer soon finds that there is a good deal of uncertainty, and that much care is needed in collating figures. In some cases a considerable part of the output is not officially reported, and returns...

Jan 1, 1924

By J T. Sharp, M A. Styler, D McGowan, P W. Mayne

Static liquefaction is a geotechnical hazard in mine tailings facilities. Soils that are contractive in shear are susceptible to static liquefaction. Tailings facilities are dynamic structures, typically growing in height each year. Dilative tailings may become contractive under increased effective stress. In this paper we show that Cone Penetration Test (CPT) data can be used to estimate the future state of in-place tailings under changes in effective stress. Susceptibility to static liquefaction is typically evaluated with the CPT by using a clean-sand equivalent normalized cone tip resistance (Qtn,cs) or by estimating the state parameter (?). An alternative approach is to evaluate the soil-state using the yield-stress-ratio (YSR = ?’y/?’v0). If the YSR equals one it is on the normal consolidation line and the soil-state is contractive. YSR values greater than three are typically dense of the critical state line (CSL) and the soil-state is dilative. In this paper we review how to calculate Qtn,cs, ?, and ?’y; and how the YSR can be used to screen for contractive soil behaviour. Unlike Qtn,cs and ?, it is very simple to estimate how the YSR will change due to an increase in overburden stress. This YSR approach was evaluated at three locations that saw increases in overburden of 10 m, 20 m, and 25 m. We show that the ?’y calculations are consistent and the increase in effective stress moves the soil state towards looser soil states. CITATION:Styler, M A, Mayne, P W, McGowan, D and Sharp, J T, 2018. Predicting changes in static liquefaction susceptibility using cone penetration test results, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 317–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By D Kentwell

For deposits where a full assay suite of elements/oxides is available and where several variables are critical to the evaluation of the deposit, it is desirable for the estimated block values of all elements/oxides to sum to 100 per cent of the weight per cent. This is difficult to achieve in practice and the estimation methods used need to be designed to minimise bias of the key elements/oxides by ensuring that block estimates are consistent with the individual assays and that the estimated totals are as close as possible to 100 per cent.This paper presents a case study of two domains within a magnetite hematite deposit, one with a high level of drilling classified as Measured and one with a lower density of drilling classified as Indicated. Several estimation methods were tested to evaluate their ability to maintain consistency of the proportions of each element/oxide and sum to 100 per cent. The following methods were evaluated: ordinary kriging, co-kriging, inverse distance and min/max autocorrelation factors (MAF) all as implemented in the Geovariances Isatis software.The comparisons showed that the MAF method produced the most robust estimates in terms of block totals and that grades and tonnages at the reporting cut-off were not significantly different between methods. At an individual block scale all methods produce artefacts that are less than desirable but can only be remedied by additional drilling.CITATION:Kentwell, D, 2015. Comparison of min/max autocorrelation factors, kriging, co-kriging and inverse distance block totals – a magnetite hematite case study, in Proceedings Iron Ore 2015, pp 465–474 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

A recent Evening Post Headline read 'Officialdoms Inertia Risking Millions in Growth Strategy'. The article beneath that headline outlined the difficulties encountered by the Government's growth strategy projects and included the paragraph 'public efforts by Government to brush up communication of the widespread nature of its growth strategy is believed to have been matched by efforts in private by some ministers to overcome their frustration at the constant delay while reports and paper work are moved between departments and through the system'. The article went on to point out that these delays could cost New Zealand millions of dollars in lost overseas exchange savings. We as responsible citizens should be appalled or at least concerned that such costly delays should or even could occur. But those on the outside of the system who spend much of their working life prodding, reminding, pleading, cajoling, even begging, the bureaucracy should be excused a smirk or a smile or even a good belly laugh. The Minister is usually a part of the bureaucracy passing judgment on someone else's proposals. This time the Government has plans of its own. Plans which it wishes to see implemented as rapidly as possible and even with the assistance of the precautionary National Development Act with its 'fast track' provisions those plans have got bogged down in the bureaucratic machine which this Government has done as much as any other to create. In the circumstances, the thought of Her Majesty's Ministers frustrated at the constant delay while reports and paper work are moved between departments and through the system is not unpleasing.

Jan 1, 1982

In an earlier paper (Stanton, 1953) a brief account was given of the geological environment and structure of the Lloyd Copper Mine orebody, Burraga, N.S.W. The present paper is concerned with the chemical and mineralogical features of the ore from this mine.Investigation has been made difficult because of inaccessibility of the workings, which have been fallen in for many years. The exact positions within the orebody of the specimens described in this paper are known in only a few cases. The specimens examined are from the collections of the Mining and Australian Museums, Sydney, and from material collected by the writer from the upper parts of the mine and from various dumps about the old workings.However, no significant variations in the nature (as distinct from grade) of the ore have been mentioned in the old reports, or by Carne (1908) or Kenny (1928), so it is likely that the specimens examined are reasonably representative of the orebody as a whole.CHEMICAL CONSTITUTIONThe ore is of simple and apparently very uniform composition.It is essentially a copper ore, with minor amounts of zinc and very minor amounts of lead. Plotting of copper against zinc shows a more or less sympathetic relationship between these at least as far as 20 per cent. copper - the highest grade assayed during the present investigation. The trend of the plots indicates a Cu/Zn ratio of about 15/1 to this point. Lead is very low and extremely sporadic, showing no clear relationships with the other metals.MINERAL COMPOSITIONThe principal non-opaque minerals are quartz and sericite, and these are accompanied by smaller quantities of muscovite, calcite and biotite. Quartz is the most abundant mineral, occurring both as a C'onstituent of the country rock a quartz-sericite schist-and as veins. All quartz aggre...

Jan 1, 1955

By C Garlick, O Gregory, H Rogers, B I. Winters, Z C. Ye

BHP New Zealand Steel produces iron from titaniferous ironsand by a direct reduction process comprising multihearth furnaces/rotary kilns/electric iron melters. The electric iron melter is a six-in-line rectangular submerged-arc furnace which takes the partially reduced ironsand (80 per cent metallisation) from the rotary kiln and completes the reduction process to produce iron of nominally three per cent carbon. As the melter operates at around 1500¦C and under very hostile conditions, it is near-impossible to obtain any basic operating parameters such as the velocity and temperature distribution in the slag and in the molten iron. As a first attempt to understand the operating conditions inside the melter, a scaled room-temperature model using wax and water to represent the slag and iron, was constructed. This paper will report on some of the preliminary model results on the temperature distribution.

Jan 1, 1995

Laboratory flotation tests on sized fractions of a certain number of selected minerals with homologous fatty acid derivatives (i.e. sodium salts and amine acetates) confirm that the higher homologues are more efficient collectors than the lower. Tests were carried out on sized material and finer size fractions floated at lower collector concentrations.It is suggested that selective flotation is best achieved with the reagent which most readily floats the most friable mineral in the ore, and that grade of product will be improved with the lowest usable homologue.INTRODUCTIONFlotation of non-sulphide minerals with fatty acids as collectors is usually less selective than the flotation of sulphide minerals with xanthate collectors. It is common to use the gradation in collecting power of homologous series of xanthates, as well as the more specific effects of activators and depressants, to achieve the separation of sulphides.The original aim of the work was to ascertain whether sodium salts of fatty acids (anionic) and fatty amine aceta:tes (cationic) could be selected from a homologous series to achieve better selectivity in separation of nonsulphide minerals by flotation. Subsequently the importance of friability of minerals in selective flotation was observed and the aim was expanded to develop a more practical approach to the testing of ore.MATERIALS USEDMineralsA series of massive mineral specimens, as pure as could be obtained, was procured. The specimens were cleaned by removing extraneous material, and then crushed and dry...

Jan 1, 1965