Search Documents

OPEN-HEARTH refractories are not merely an accessory to the furnace. They themselves ore the furnace, to all intents and purposes. The steel work of the main structure is merely a frame which helps to support the refractories; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories with very little supporting structure. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a refractory- protected rod. The liquid is sometimes sent through an additional refractory-lined tun-dish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a non-conducting "hot top." These materials, from ladle to hot top inclusive, are often referred to as the "pouring-pit refractories." CAUSES OF FAILURE Compared with the equipment used in most industrial processes the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. The discussion here of the individual refractory materials will therefore keep uppermost the question "Why, how, and where does it fail?" The principal causes of failure of open-hearth refractories are, in their order of importance: 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spallimg. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. This is by far the most important cause of failure. Liquid iron oxide comes very near to being the

Jan 1, 1944

By George Newton

When Mr. Bailey asked us to present a paper describing our new BOF shop, he requested that we avoid a presentation heavily laden with detail and statistics. Not only have we attempted to do this, but also we have prepared a number of colour slides which, hopefully, will provide you with a graphic conception of the facility. The installation of the BOF facility at the Steel Co. of Canada's Hilton Works was delayed many years because of the remarkable production growth of the oxygen open hearth furnaces in No. 3 shop. However, in mid-1960 it became strongly evident that not only would increased ingot capacity be required, but also that N0.2 shop - with vintage non-oxygen open hearth furnaces - would have to clean its stacks in the near future, or be closed down. A decision to embark on the BOF facility was made in 1967 after an extended period of in-depth planning and assessment of industry trends.

Jan 1, 1972

By Mark Eisner

ONE'S JOB is the watershed down which the rest of one's life tends to flow write the Lynds in the first pages of their classic social study, "Middletown in Transition." Certainly engineers will confirm this statement after a check among those in their own profession with whose lives they are at all familiar. I have no hesitancy in acknowledging the truth of their observation for the men and women who are engaged in the profession of the law. It has been often remarked that American public life is overrun with members of the law profession. The highest public office in the land, that of President. has been occupied by lawyers almost to the exclusion of citizens of any of the other professions. Twenty-two Presidents of the United States out of the total of 31, were members of the bar. For the most part, members of Congress, the governors of the states, the state legislators and the mayors and other local leaders, men who occupy important positions of responsibility and public trust, have had legal training. Now this fact is no mere accident. Those who were fitted for the "job" of the practice of the law are favorably placed with respect to their participation in public life. Thus public service and public office is the watershed down which the "lawyer's" life tends to flow.

Jan 1, 1940

By B. Wilshire, P. W. Davis

It has been shown that grain-boundary migration during high-temperature creep can reduce or even prevent the formation of intercrystalline voids, giving a considerable increase in ductility.' A similar observation has been made in a recent investigation of the creep properties of various grades of nickel and nickel alloys. The results can be illustrated by the observations made on: a) Pure vacuum-cast nickel (99.993 pct Ni) b) Impure vacuum-cast nickel (99.97 pct Ni) c) Pure nickel containing internal voids (produced by a process of intering). d) A substitutional solid solution alloy of pure nickel containing 1.16 pct Sn. All the materials were given a high-temperature anneal (>850°C) to produce a stable grain size of 7 to 10 grains per linear mm. The apparatus and techniques used to obtain the present results have been described elsewhere.' In this series, grain growth was observed only in the highest-purity, vacuum-cast metal. Thus we may consider that in the other materials grain-boundary migration was prevented by either preexisting voids or solute atoms. The effect of migration on the creep ductility of the above materials can be seen from Fig. 1, which

Jan 1, 1962

By AIME AIME

THE Fall Meetings of the Institute of Metals Division and of the Iron and Steel Division were held in Cleveland from Tuesday, Oct. 20, to Thursday, Oct. 22, as a part of the National Metal Congress. The registration at the technical sessions was something over 450 and the attendance at the joint dinner of the two Divisions on Wednesday evening taxed the capacity of the dining room. The president of the British Institute of Metals, W. R. Barclay, consulting metallurgist to the Mond Nickel Co., Ltd.; of London, was in attendance at several of the technical sessions and was one of the after-dinner speakers at the banquet. He commented on the desirability of greater international amity and cooperation in these troubled times and of the role that technical societies, such as the A. I. M. E. and his own British Institute of Metals, can and indeed are playing in bringing this to pass, with their membership and contacts reaching to all parts of the world. He also referred to the new reciprocal membership arrangements in effect between the A.I.M.E. and the British Institute of Metals.

Jan 1, 1936

Preheating Feature of Leyner Oil Furnace for Heating Drill Steel The No. 3 Leyner oil-burning furnace, used for heating drill steel, is now made with a preheating chamber. By this addition it is claimed that the heating capacity and, effeciency of the furnace are increased about 50 per cent. This preheater is a section which fits between the body and cover of the furnace of the old design. It may be attached to an old furnace by simply changing a few bolts. Referring to the illustration, it will be seen that the lower chamber is used for the final heating and the upper one for preheating. The type of burner now furnished with this furnace is suitable for either high- or low-pressure air. It hats merely to be throttled for high pressures and when this is done, it, is as efficient as burners designed especially for high pressures and eliminates the noise common to such burners. This furnace burns petroleum or any of its oils, such a, gasoline, kerosene, distillate, etc. Oil heating has many advantages. The steel cannot be injured by absorbing injurious elements such as sulphur, phosphorus or other impurities which :ire present in nearly all coals, nor from unequal heating since the flame imparts a uniform temperature; further, o lie steel is in full view of the operator at all times.

Jan 3, 1916

By AIME AIME

MOST of the copper mines in Canada are favored by nature in having other metals besides, copper in their ore, which puts them in a most satisfactory competitive position. Noranda ore has an important gold content, Flin Flon gold and zinc, and International Nickel of course has nickel. All of the larger copper companies in Canada operated during 1.933 and the total production of copper exceeded that of the year before. The Britannia Mining and Smelting Co. worked out to succcessful conclusion a three-product flotation process for separating the copper, zinc and iron from its low-grade ore. Although the method and equipment is different from that used at the Flin Flon mine, the object is the same, that

Jan 1, 1934

By S. C. Lindsay, D. J. I. Evans

With each year that passes hydrometallurgical processes are being more widely used to recover base metals from ores and concentrates. Generally these processes involve liquid-solid separation of metal-bearing liquors from barren residues. This may be done by countercurrent decantation, thickening and filtration, or filtration or centrifuging only. Choice of method is governed by chemical and physical characteristics of the pulps; cost of labor, power, materials, and waste disposal; and even by the amount of capital available when building plans are under way. Since all these controlling factors change with time and location and with technological advances, the separation method must be re-evaluated when new plants or expansion programs are contemplated. At the Sherritt Gordon refinery in Fort Saskatchewan, Alberta, an ammonia pressure leaching process recovers nickel, copper, and cobalt from the nickel concentrate produced at Lynn Lake, Manitoba.' Pregnant liquors are separated from the barren leach residues in a thickener-filter liquid-solids circuit. The decision to use this type of separation was based on a summation of economic factors during the pilot plant and design stages. Although countercurrent decantation was not incorporated in the refinery flowsheet, the problems solved in thickening the leach residues and the experience gained in operating the commercial plant are pertinent to countercurrent decantation, particularly where it is applied to slow-settling leach slurries or slurries having a relatively high vapor pressure of a valuable, obnoxious, or poisonous vapor. The nickel sulfide concentrate is leached under pressure with air and ammonia to dissolve the nickel, copper, and cobalt and most of the sulfur, leaving a residue of iron and siliceous material to be discarded.2,3 During a subsequent distillation stage to recirculate part of the ammonia used for leaching, copper is recovered from the solution as a high-grade sulfide. After further purification to remove traces of copper and undesirable sulfur compounds, the nickel is precipitated by hydrogen under pressure at an elevated temperature. The cobalt, together with unreduced nickel, is precipitated as a mixed metal sulfide by hydrogen sulfide for eventual cobalt recovery. The end solution is then evaporated to produce a crystalline ammonium sulfate byproduct. As shown in Fig. 1, the nickel concentrate is leached in a continuous, two-stage, countercurrent circuit. In the first stage, or adjustment leach, the fresh concentrate is partially leached (60 pct) in the liquor produced in the second stage, or final leach. This system is necessary to produce a solution suitable for treatment in the copper sulfide precipitation step. Both stages are carried out at 170" to 180°F under a total pressure, with air, of 100 to 120 psig in large, horizontal, water-cooled autoclaves. The autoclaves are divided by overflow weirs into four compartments to give a certain amount of staging during leaching. In each compartment a relatively slow-speed (100 to 150 rpm) agitator maintains the nickel concentrate in suspension. Adjustment leaching, carried out in two autoclaves in parallel, is followed by a thickener-filter liquid-solids separation. Final leaching is done in two parallel trains of three autoclaves using aqueous ammonia to extract metal values from the adjustment leach residues. This too is followed by a thickener-filter circuit. Here the residues are repulped once with aqueous ammonia and twice with process water and refiltered after each repulping stage, to insure a maximum recovery of soluble metal, before being discarded to the tailings pond. The adjustment leach is followed by a seven-disk Dorr-Oliver American filter, with an agitator in the filter boot to keep the residues in suspension. Agitators have also been installed beneath the four ten-disk filters following the final leach thickener. Slurry Characteristics: A typical analysis of the Lynn Lake nickel concentrate, produced by differential flotation,' is given in Table I. The concentrate comprises 35 to 49 pct pentlandite, (Fe, Ni)S; 3 to 6 pct chalcopyrite, CuFeS,; 1 to 4 pct pyrite, FeS2; and 24 to 42 pct pyrrhotite, Fe1-2S (where x varies between 0 and 0.2) together with various siliceous minerals such as actinolite, hornblende, and talc. During leaching, the sulfur in the pentlandite, chalcopyrite, and part of the pyrrhotite is successively oxidized through the thiosulfate and poly-thionate radicals to sulfate and sulfamate." Simultaneously the nickel, copper, and cobalt are converted to soluble ammine complexes and the iron in the pentlandite, chalcopyrite, and part of the pyrrhotite is oxidized to a spongy hydrated iron oxide. The hydrated iron oxide is readily broken down by the agitation needed to sustain the concentrate in suspension and to maintain a satisfactory mass transfer of the oxygen from the air to the slurry. Table I shows typical chemical, screen, and

Jan 1, 1961

By S. H. Ward, R. A. Barker

THE Juniper Prospect is in Carleton County, N. B., at approximately 46" 31' north latitude, 67" 20' west longitude. During the summer of 1955 an area in west-central New Brunswick was selected for aerial electromagnetic prospecting with American Metal Co.'s helicopter-mounted equipment. Generalized, small-scale government geologic maps had suggested that this area was located along the western border of the northeast-trending granitic backbone of northwestern New Brunswick and might be underlain by the Ordovician-Silurian sediments and volcanics that are the host rocks for the recently discovered sul-fide deposits of the Bathurst-Newcastle district. The helicopter electromagnetic equipment located an anomalous conductive area, coincident with a small aeromagnetic closure, about five miles west of the town of Juniper. Subsequently 30 mining claims (total area about 6600 x 8000 ft) were staked and company personnel conducted geological, geophysical, and geochemical investigations on the property. The claims and immediately contiguous areas were mapped geologically, and an area of about 2000 x 4000 ft was soil-sampled and also surveyed by ground electromagnetic and gravity methods. Finally six diamond drillholes, totaling 3500 ft in length, were drilled to test the anomalous conditions discovered by the several exploration techniques used. The discovery of base metal sulfides during drilling was a technical success for the exploration methods, but the quantity of sulfides was too small to be profitably exploited.

Jan 1, 1959

By M. N. Brodie, John Chapman

INTRODUCTION - DEFINITION & HISTORICAL PERSPECTIVE While this symposium is concerned with comminution which, by definition, relates to all stages of size reduction of an ore body to a form suitable for mineral separation, the electrical drive aspect of the grinding section will receive most attention in contrast to the crushing, screening and materials handling elements of the process. The reason for this is that today's large mills, thirty feet diameter and upwards, present mechanical and electrical problems which require a degree of sophistication in their solution not previously required. The ability to satisfy these demands, so far as electrical technology is concerned, largely results from the development of semi-conductor devices. These can now handle typical electrical distribution power levels within remarkably s m all volumes and with high efficiency when compared with the motor-generator sets, mercury arc rectifiers, rotating amplifiers, magnetic amplifiers and vacuum tubes which were commonly used to provide speed and torque controls as recently as the early nineteen-sixties. The hardware available to the electrical engineer has changed dramatically whereby even the simplest control system formerly using hard-wired relays is now superseded by the program m able logic controller with its computer-like memory containing the sequence of operation, in other words, the software. Reverting now to the mineral process itself, it is assumed that the ore body has been mined using explosives and is delivered to the concentrating plant in its 'run of mine' form. The problem becomes one of reducing the material to a size which will permit an acceptable recovery of the mineral with the most economical use of energy. The size of 'run of mine' material will range from about minus five feet for high tonnage open pit operations to minus two feet for the smaller underground mine. The final reduction in size may range from minus ten mesh to minus two hundred mesh (exceptionally as fine as minus six hundred mesh) depending upon the concentration method and dissemination of the mineral values within the ore. There is no single circuit that satisfies all applications, but the pattern of metallurgical equipment use shown in Table 1 appears discernable from current practice, in general terms.

Jan 1, 1982

By J. A. Herrick

SOME time ago the writer needed a cheap, light, and portable hydraulic lift or crane, that would be universal in its application, and that might -be suspended from crane-arms, overhead tramways, beams, etc., and serve all the uses of ordinary hydraulic cranes. This was accomplished by the use of a closed cylinder of wrought-iron hydraulic pipe, provided at its top with the ordinary gland and stuffing-box, through the centre of which passed another similar pipe of slightly smaller diameter, forming in effect the ordinary plunger of the regular hydraulic crane. Over the top of this centre pipe or plunger or piston a disk of iron is placed with two arms projecting several inches from the rim, as may be required. Through these arms long iron rods pass, one on each. side, and are fastened in place by nuts screwed to a bearing immediately above and below the disk. These rods also pass through the enlarged head of the lift down through a casting which closes the bottom of the cylinder, which, at the same time, gives them a bearing, and they terminate at a point below the casting equal to the height of the lift of the crane. The rods at this point pass through a disk similar to the top disk and are similarly secured in place. A common hook arranged with a swivel passes through the centre of the disk, and on this hook the load is suspended. For a stationary hanging crane the apparatus is suspended by two rods passing through the head of the lift in similar manner to the two already described, at right angles to the first, and of sufficient length to let the first set play between them and rise to the full height which the plunger will allow. The second set of rods terminates in an iron disk similar to the one at the bottom of the first set, and a hook through this in turn suspends the entire apparatus. In order to adapt the lift to an overhead tramway, single or double, in place of the suspending rods, a projection or offset is arranged on each side of the head of the lift and a journal cast in, allowing the lift to be suspended on pivots arranged as follows

Jan 1, 1879

By J. A. Herrick

Some time ago the writer needed a cheap, light, and portable hydraulic lift or crane, that would be universal in its application, and that might .be suspended from crane-arms, overhead tramways, beams, etc., and serve all the uses of ordinary hydraulic cranes. This was accomplished by the use of a closed cylinder of wroughtiron hydraulic pipe, provided at its top with the ordinary gland and stuffing-box, through the centre of which passed another similar pipe of slightly smaller diameter, forming in effect the ordinary plunger of the regular hydraulic crane. Over the top of this centre pipe or plunger or piston a disk of iron is placed with two arms projecting several inches from the rim, as may be required. Through these arms long iron rods pass, one on each side, and are fastened in place by nuts screwed to a bearing immediately above and below the disk. These rods also pass through the enlarged head of the lift down through a casting which closes the bottom of the cylinder, which, at the same time, gives them a bearing, and they terminate at a point below the casting equal to the height of the lift of the crane. The rods at this point pass through a disk similar to the top disk and are similarly secured in place. A common hook arranged with a swivel passes through the centre of the disk, and on this hook the load is suspended. For a stationary hanging crane the apparatus is suspended by two rods passing through the head of the lift in similar manner to the two already described, at right' angles to the first, and of sufficient length to let the first set play between them and rise to the full height which the plunger will allow. The second set of rods terminates in an iron disk similar to the one at the bottom of the first set, and a hook through this in turn suspends the entire apparatus. In order to adapt the lift to an overhead tramway, single or double, in place of the suspending rods, a projection or offset is arranged on each side of the head of the lift and a journal cast in, allowing the lift to be suspended on pivots arranged as follows:

Jan 1, 1879

By Harry H. Power

INDUSTRY has the right to expect the petroleum engineering schools to supply more than the minimum technical qualifications necessary to obtain or discharge the responsibilities of a particular job. The basic training, social and economic orientation, should go far beyond these minimum requirements. Petroleum engineering students should also be well grounded in the history of the oil business so that they may understand the industry's progress since the advent of the Drake well. Furthermore, according to P. H. Bohart, the schools "have a definite duty to help the students form a workable philosophy of life, which includes an appreciation of the service of science to mankind, and a belief in the obligation of the individual who enters a profession to exalt himself by continuing his studies and growth so that he may never cease making contributions to the advancement of science and industry."

Jan 1, 1948

By W. G. Pfann

THE problem of forming points on wires that were from 0.002 in. to 0.010 in. in diam arose in the recent appearance of silicon and germanium point contact rectifiers as elements in microwave radar.1 In these devices a pointed tungsten wire makes a delicate contact with the surface of a semiconductor. Because the quality of such rectifiers is largely determined by the nature of this contact, considerable attention has been given to the formation of the metal point. Reproducibility of contour and freedom from burrs and even microscopic irregularities are considered essential. The operations involved must be simple and rapid enough for mass production. Previously tungsten wires had been provided with conical points by a grinding method which involved rotating a wire about its axis and causing it to bear at an oblique angle against a spinning abrasive disc. This was later complemented with an electrolytic polishing treatment which removed irregularities from the ground point and also rounded it off at the tip-a desirable feature. Finally, these operations were supplanted by the electrolytic pointing method described here. MECHANISM OF POINT FORMATION The wires to be pointed are partially immersed- in an electrolyte in a .vertical position whereupon they are provided with smooth rounded points entirely by electrochemical action. The process is independent of the depths to which the wires penetrate the electrolyte because the points are formed at the surface level. It may be used to point a single wire or many of them simultaneously and is applicable to wires of different diameters within a limited range. Solution of the immersed portion of a tungsten wire is accomplished by making it the positive electrode in an electrolytic cell, as shown in Fig I. While the wire is maintained at constant voltage the current through the cell falls continuously, principally because of the decrease in wetted area which results from solution of the tungsten. This increase in resistance occurs in a reproducible manner and is used as a control in the process. As the immersed portion of the wire dissolves, it remains cylindrical in shape except for the short section which is wetted by the meniscus. Here the rate of solution is lower and decreases as the top of the meniscus is approached. The result is the formation of a tapered section inside the meniscus. As solution continues, the cylindrical section either dissolves entirely or drops off just before complete solution, leaving only the taper which is now sharply pointed. Further action causes this point to become rounded and then quite blunt, until finally the end of the wire is almost plane. Fig 2 shows the stages in this development. Contour PF is most representative of those used in point contact rectifiers. Thus a variety of point

Jan 1, 1947

By WM. E. Mlligan

IN the last year, much information had become available as to the extent that zinc participated in the war effort. The importance of foreign zinc in this program had been indicated by Bateman (M&M April 1945) as of the order of 400,000 tons annually in zinc or contained zinc. Pehrson (M&M April 1945) reviewed the domestic ore-reserve situation with respect to most minerals and metals and showed the extent to which commercial zinc ores had become depleted in this country. This picture was further darkened by O.P.A. figures appearing in E.&M.J. July 1945 in which figures for total production during the three previous years were broken down into percentages produced under ceiling and various quota price categories. True, factors other than depleted ore reserves contributed to this picture. Among the more important of these, were shortage and high cost of labor, both skilled and unskilled, and the general difficulty and cost of maintaining adequate equipment and supplies. The cost of production in the Tri-State district was most affected.

Jan 1, 1946

By L. S. Darken

IN the study of reactions occurring in liquid iron, alone or in contact with a liquid oxide or slag phase, it has been found that the experimental data over a limited range of concentration can in some cases be repre-sented satisfactorily by the simple equilibrium expression K - (p1)p1 (p2)p2 . (R1)r1(R2)r2 . where (P) denotes the concentration of a product and (R) the concentra-tion of a reactant in the reaction r1R1 + r2R2 + . . . Some of the reactions for which it holds are listed in Table 1. For others, however, the simple equation apparently does not hold. This has been attributed to an improper method of expressing concentration (for instance, weight per cent instead of mol fraction); or it has been supposed that the solutions are not ideal in the sense that the activity of a com-ponent is not proportional to its true mol fraction, But it may be that the problem has been oversimplified by neglecting some molecular species actually present; that is, by considering only the ostensible simple com-ponents and thus leaving out of account possible compound formation. It is the purpose of the present paper to point out how, in a group of related cases, a reasonable consistent assumption relative to the presence of a compound makes it possible to express the experimental data satis-factorily by the simple equilibrium expression when this compound is taken into account, and to bring into harmony data referring to different reactions in liquid iron. There are several a priori reasons for believing that solutions in liquid iron should not deviate far from ideality, provided that the concentration of solute is not too great and is expressed in proper terms. The factors that commonly lead to nonideality in systems at ordinary temperature as ionization or the occurrence of polar and nonpolar molecules-are presumably less effective in metal and in slag systems at high temperature. Again, the type of equation commonly used to express the value of

Jan 1, 1940

By J. W. Halley, T. S. Washburn

RIMMING steels derive their name from their action during solidification in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop in the molds, are determined by the composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard, 1, 2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.7 The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors.6 Meyer,8 in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federations studied distribution in one billet and one ingot of rimmed steel.. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accurately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring conditions and furnace practice on the distribution, though there is still much to be done in this direction. The structure of a rimmed ingot that has been split by dynamiting and a schematic diagram of the zones in the ingot are illustrated in Fig. 1.

Jan 1, 1938

By J. W. Halley, T. S. Washburn

Rimming steels derive their name from their action during solidification in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop in the molds, are determined by the composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard,1,2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.? The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors6 Meyer: in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federation9 studied distribution in one billet and one ingot of rimmed steel. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accurately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring conditions and furnace practice on the distribution, though there is still much to be done in this direction. The structure of a rimmed ingot that has been split by dynamiting and a schematic diagram of the zones in the ingot are illustrated in Fig. 1.

Jan 1, 1938

By J. W. Halley, T. S. Washburn

Rimming steels derive their name from their action during solidification in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop in the molds, are determined by the composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard,1,2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.? The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors6 Meyer: in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federation9 studied distribution in one billet and one ingot of rimmed steel. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accurately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring conditions and furnace practice on the distribution, though there is still much to be done in this direction. The structure of a rimmed ingot that has been split by dynamiting and a schematic diagram of the zones in the ingot are illustrated in Fig. 1.

Jan 1, 1938

Coal - Surface Mining Coal Preparation Coal Utilization Research and Development Health and Safety

Jan 3, 1976