Search Documents

By Kenneth S. Ritchie

TOO often, many foremen; superintendents, managers, and executives, "The Bosses" of the oil and mining industries, do not fully realize: (1) How much personal actions '.on the job" may reduce their effectiveness in getting work done; and, (2) The importance of harmonious relations with their fellow men. Today. these qualities of personality in the people entrusted with the positions of responsibility are more important than ever with the shortages of labor so critical in vital war production. Likewise, many engineers do not fully realize that their work is essentially executive in character; i.e., other people do the actual labor. Without their help. the engineer's work would not be done. A clearer appreciation of this fact would increase their interest: (1) in the nontechnical aspects of their work. and, (2)in their relations with others, particularly the individuals in their own organization. Consequently, these engineers would be more successful in equipping themselves for greater responsibilities and increased remuneration.

Jan 1, 1944

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By H. C. Fowler, G. B. Shea

MODERN industry's incessant demands for increased operating efficiency and lower costs require that hazards attending all occupations be reduced to a minimum. Reduction of the inevitable losses that result from accidents and injury to the worker is one of the important economic problems confronting industry today and is the basis for the widespread safety movement. Dr. Charles E. Munroe, chief explosive chemist of the U. S. Bureau of Mines, is father of the statement, "The existence of a nuisance is evidence of an economic waste." This pointed expression of the internationally recognized scholar and explosives engineer has a direct relation to the prevention of accidents. Every injury and death in industry is a waste in human endeavor and a lessening of productive gain. Dr. Munroe has aptly paraphrased his previous summation with reference to wastes as follows: "A lost-time accident is evidence of an economic waste." That the economic waste entailed by occupational accidents is chargeable to industry is well substantiated by the fact that all but four states (Mississippi, South Carolina, Florida and Arkansas) now have workingmen's liability and compensation laws.

Jan 1, 1933

By J. R. Kyte, L. A. Rapoport

The material balance equation for partiai or complete 1:trter-drivc reser1,oir.s been re-arranged to include a pressure irrferferencr ternr. This pressure interfernce term was ohtained from the theory established hy Morinda. A .successful progranl deissed to solve the resrclritlg c,qrration in a few hours on a nleelitr .sizeti, digital compuier. No prior knowdelge of the properties of the eqrrifer is required in the solution. 7' ri~rl calculations areatle using various assumed con!binuiions of value of the constant expretsing the qquifer properties correspoinds to the best fit ohtained between observed and calculated field history. Details of the method of calculaion are illus trated by an example. INTKCDUCTICN A method 01' calculating the material balance equation for a partial water-drive reservoir completed in an aquifer has been described in the literature." Pressure interference i'rc,m other pools iocated in the same nquiucr is not taken into account in this solution. When present, the pres- sure interference effect must be included in order to make a complete performance analysis. A correction for this effect has been developed using the theory cstahlished by Mor-tada.' Manual calculation of the material balance for water-drive reservoirs is a formidable task. Such manual ca1culation when interference eflects are includcd would be impossible to completc in any reasonable time period. However, a medium-sized stored program, digltal conlputer can he used satisfactorily. The method is described in the following sections. THECKETICAL CONSIDEKATIOhS The material balance equation for a reservoir producing by partial or total water drive, as proposed by Van Everdingen, This relationship is linear for Z/a from which thc slopc, Z, and the intercept, N, can be obtained by the least-squares method from the data points. It is not necessary lo know the aquifer properties to uktain oplimum values tor 2nd IV. Various assumptions are made tor At,,: where 11 is production time, seconds (oilfield between the equal successive time intervals into which the history is divided. t,, h It, times the number of equal time periods from i.e.. the total dimen-sionless time interval from It is noted that the dinlensionless time interval, At,,, involves all the relevant aquifer properties. Accordingly, any assunlption of is an assumption of the combined aquifer properties which pertain to the solution of the equation. Deviations of the data points from a straight line arc calculated for each assumption of and the value of A, correspond ing to the minimunl deviation is chosen as the optimum solution. This method is described in Ref. 1 and 2. Thc material balance solution is usually made with an initial assumption that the reservoir being studied is located in an infinite aquifer from which there are no other withdrawals. Deviation of the points by amounts greater than can be attributed to inaccuracies in field data may be the result of: (1) boundary effects of a limited aquifer, (2) pressure interference from othcr pools completed in the .sarne aquifer, and (3) a combination of these effects. Differentiation of these effects can be made only on the basis of geologic data. Pressure interference from other fields will result in a pressure drop at the original oil-water boundary having an interference component, The measured instantaneous pressure drops at the oil-water

By Benjamin Smith Lyman

THE importance of topography to geology is so commonly underrated as to deserve to be pointed out again and again. The relation of topography to the different branches of geology may be seen best by a glance at them all. Geology is well understood to consist of the observation of facts about rocks as materials of the earth (geognosy), and the explanation of those facts (geognosy). The facts to observe are : I. GEOMETRICAL, as (1) structure, including the dip and strike at different points, the size, shape, and position of basins and saddles; (2) vertical section, that is, the thickness of rock groups and of their parts ; (3) horizontal or geographical position. 11. PHYSICAL, such as texture, whether sedimentary or crystalline ; and, if crystalline, whether granitic, porphyritic, amygdaloidal, globular, or concretionary ; whether compact or granular; coarse or fine; pervious or impervious; hard or soft; firm or tender; with cleavage or without ; massive or thin ; the microscopic structure ; also whether magnetic or not ; soluble or insoluble ; fusible or infusible ; and the constituent minerals. 111. CHEMICAL that is, the composition of the rocks and of their minerals and their affinities. IV. PALAENTOLOGICAL, as what kind of fossils are in the rocks,

By J. R. McWilliams

Several of the current concepts of brittle fracture involve consideration of the existence of defects or flaws. Griffith 1 observed that the tensile strength of brittle materials was several orders of magnitude less than might be expected from the calculated strength of the molecular bonds. He was able to show that the stress concentration at the tip of an elliptical crack is sufficient to raise the local stress level many fold. He therefore proposed that real materials do contain such stress risers in the form of minute cracks and that this accounts for the rather large difference between theoretical and actual strengths of brittle materials. The degree of stress magnification depends to a great extent upon the orientation of the crack with respect to the general stress system, and to the general geometry of the crack.

Jan 1, 1967

By Reno H. Sales

Our colleagues cannot in the future earn reputations and medals for achievements in milling and smelting ore and for successful management of mining companies, if some one doesn't keep finding and mining the ore to mill and smelt and to provide the basis for the good management. Good ore seems sometimes to be quite helpful to good management, and good ore is not as easy to find as it used to be. And there are still more reasons, why—when this honor had been decided upon and named for Mr. Daniel C. Jackling—it should be initially conferred on Reno H. Sales. . The terms of reference of the award are that it should be conferred upon an individual working in the fields of mining, geology, geophysics, who has made an outstanding contribution to the progress of technology in one or more of those fields. And in this initial year (the earlier years are the easiest) just that was done. I think I could get away with it amongst the old-timers of my generation if I say that this time they made the award to the individual, who made the outstanding contribution. But, as Al Smith used to say, "Let's look at the record." Really, the record is mixed up a little with extra-lateral litigation—the old-time "apex cases" under Section 2322 of the Revised Statutes. Reno Sales doesn't like such litigation, but there is little question that the urgency, generated by conflicting claims of intra-limital and extra-lateral rights, and consequent necessity for committing to records and maps the complications of Butte structure, did advance—and by several years—the first continuous, accurate, systematic, and scientific portrayal of the geological and mineralogical details of what is, after all, the most important and the most complicated copper district—at least in North America. Prior to Sales' time, some of the most eminent of geologists often waived details. One geologist took the judge to the window to show him the Rarus fault going through a notch in the Continental Divide. The entertaining testimony in the Bluebird litigation was as perfect in literary style as it was innocent of the criteria by which faulting and lack of continuity of vein structure are now recognized. At any rate, this need for an accurate record of structure was in the background—to whatever extent it was, or was not, the etiological agent—for formation of the Geological Department of the Amalgamated Copper Co. in and about the year 1900. Charles W. Goodale was at that time the head of the Boston & Montana, and John D. Ryan succeeded William Scallon as the president of Anaconda Copper Mining Co. in 1905. Horace V. Winchell, for years a specialist in extra-lateral litigation, was perhaps the man who at that date had the vision, the persuasive weight with the management, and the willingness to defend the idea of large current expenditures (as then viewed) for a complete and sys-

Jan 1, 1955

By G. H. Wigton

THE oxidized ores of the Chief Consolidated Mining Co., in the Tintic mining district, have never yielded to metallurgical treatment by any standard method except smelting. These ores occur in comparatively small, irregular, siliceous replacements in limestone, and carry silver, lead, and gold as the principal valuable metals. But smelting methods. are unsatisfactory, as the lead smelters heavily penalize the large amount of silica in the ore, and the copper smelters do not pay for the lead in the ore; therefore, an alternative treatment method was sought. In 1916, a metallurgical research department was organized under; the direction of the writer. Many standard metallurgical methods were investigated but, on oxidized ore, none yielded extraction great enough to make its use feasible. During some chloridizing-roasting experiments in 1916, made in an assay muffle, the writer noted that large proportions of the silver, lead, and gold were volatilized from certain oxidized ores. The possibility of volatilizing the metals and collecting them in the form of a concentrated fume was then studied. But, as it was shown that satisfactory chloride-volatilization would be limited to a furnace feed with a high fusing temperature of the non-volatilizable constituents, and as the results obtained in a rotary kiln with the admixture of common salt with the ground ore were inferior to muffle tests, further volatilization experiments were discontinued until 1920. During this interval, an experimental sulfidizing and flotation plant was operated. After the cessation of attempts to float the oxidized minerals, chloride-volatilization experiments were resumed. The highly infusible flotation. tailing from the operation of the flotation mill was used for furnace feed. The first tests made on flotation tailing mixed with 10 per cent. common salt showed -nearly complete lead and gold volatilization but considerably less volatilization of silver than in muffle tests. In attempts to increase the silver extraction, the percentage salt in the furnace feed was varied, and it soon became apparent that the use of smaller percentages of salt raised the fusion temperature of the furnace charge and thus,

Jan 8, 1925

By D. H. Gurinsky, D. G. Schweitzer

The empirical equilibrium constantsd the heat of reaction for the reduction have been determined from 300° to 500°C. The mechanisms of the oxidation of uranium and magnesium from dilute bismuth solutions have been investigated. The kinetics of some of the reactions were affected by air adsorbed on the uranium oxides. THE Liquid Metal Fuel Reactor studied at Brook-haven National Laboratory uses a solution of uranium in bismuth as the fuel. Corrosion and stability problems require that the fuel solution contain corrosion inhibitors and deoxidants. Of the additives tested, magnesium has been found to be the best deoxidant and zirconium the best corrosion inhibitor in bismuth. Some experiments1 indicate that magnesium may play a secondary role in increasing the effectiveness of zirconium in inhibiting corrosion. The work reported here was intended to determine the relative concentrations of Mg and U required to prevent oxidation of the uranium fuel in the event of an air leak. In addition, an attempt was made to identify some of the mechanisms of the oxidation and reduction reactions occurring in the liquid bismuth solutions. EXPERIMENTAL Apparatus and Procedure—The equipment shown in Fig. 1 was designed so that the reaction kinetics could be studied as functions of temperature, melt composition, pressure, and flow rate. At the start of a run, the 10-liter bell jar (F) is removed by opening the bottom Dresser fitting (L), and the bismuth and additives are placed in a pyrex crystallizing dish (I). The bell jar is replaced, the system is evacuated to 10-5 to 10-6 mm Hg and then the heater (J) is turned on. When the selected temperature is reached, the oxidizing gas is admitted to the system to the desired pressure as read on the manometer (D). Gas is introduced through the slide tube (Q) which has a pyrex frit (R) sealed to its bottom. Stirring is accomplished by immersing the end of the tube in the melt. To maintain a constant pressure under flow the input and evacuation rates must be equalized. To obtain this condition stopcock (C) is closed and flowmeters (B) are matched. The reaction is "stopped" by closing the inlet flowmeter and quickly evacuating the system. To obtain a liquid metal sample, the system is evacuated with the sampler positioned near the surface of the liquid. The sampler, Fig. 2, is then immersed until its thermocouple reading matches thermocouple (G) Fig. 1. The system is then pressurized with helium which forces the solution through the frit. Twenty to 30 min elapsed between the time the system was evacuated and sampled. During evacuation and pressurization of the system, the temperature variations did not exceed ± 5°C. While bubbling occurred the temperature remained constant to within 1/2 oC. The volume of the equipment was determined by adding a known volume of air at atmospheric pressure to the evacuated system and noting the resulting pressure.

Jan 1, 1962

By Fred D. Wright, Philip B. Bucky

FOREWORD By E. D. Gardner[$] THE present known petroleum reserves are limited, and unless important new fields are discovered the Nation will be dependent, in the not too distant future, upon imports or upon synthetic liquid fuels to supplement domestic petroleum supplies. As a national defense measure, it would appear desirable to develop a substitute source of liquid fuels within the borders of the country if new discoveries of petroleum should prove disappointing. Congress undoubtedly had this in mind when it passed the Synthetic Liquid Fuels Act (78th Congress, approved April 5, 1944). The act directed the Bureau of Mines to construct and operate demonstration plants for producing synthetic liquid fuels from coal and oil shale, and from forestry and agricultural products. As a part of this program, the Bureau of Mines has built a demonstration plant at Anvil Points, near Rifle, Colo., for retorting the oil shale, and has developed a mine to supply the plant with oil shale. At the beginning of mining operations, the physical qualities of the oil shale, which would have a bearing upon the selection of mining methods and practices for exploiting the deposits, were largely unknown. A comprehensive mining-research program has been set up to determine the best methods and practices to follow to obtain the lowest overall practicable mining cost for producing the oil shale on a large scale. Unusually low mining costs will be necessary for shale oil to be produced commercially. Consideration now is being given to exploiting a series of flat-lying beds 70 ft thick by a room-and-pillar method of three benches with the advance heading at the top. This report is one of a series giving the results obtained in research on mining problems. INTRODUCTION The structure and physical qualities of the oil shale indicate that the 70-ft interval of the oil-shale measure can be safely mined in open stopes; studies indicate that this method would be the most economical one to use.1 As labor will be a major item of expense, the largest equipment that could be operated efficiently in the workings would be required to obtain the lowest practicable mining cost. It was therefore desirable to know the maximum safe span of unsupported rooms and the size of pillars necessary to support the overburden. This paper describes the work done at the Columbia School of Mines Barodynamic Laboratory in determining the maximum safe unsupported roof spans and the minimum safe pillar dimensions for the oil-shale mine at Rifle, Colo.

Jan 1, 1947

By A. W. Ruff

The seismic wave produced by an explosive is very important in blasting. A true understanding of the wave is only important when considering possible structural damage to buildings located near the blast, but it is also of primary importance when considering rock fragmentation. Because of the importance of the seismic wave to fragmentation, a finda-mental study of the seismic wave and its effect was made at the Cananea Consolidated Copper Co.'s mine at Cananea, Sonora, Mexico. Strain gages were used to measure the strain in the rock when nearby explosive charges were detonated. The variance in the circuit voltage caused by changes in the resistance of the strain gage was measured with an oscilloscope and recorded with a Polaroid camera. CONFINED DRILLHOLE CHARGES To record the seismic wave from a confined drillhole explosive charge, a gage was cemented to the bottom of a 4-in diam drillhole. The horizontal gage hole and nine horizontal charge holes were drilled perpendicular to the center line of the 2-39 drift and 4 ft above the floor. The gage hole was 29 in. deep, and the charge holes were drilled so that each bottomed 1 in. deeper than the gage hole. The gage was installed with its axis horizontal and parallel to the 2-39 drift. The charge holes had the following horizontal distances from the gage: hole 3, 3 ft; hole 4, 4 ft; hole 5, 5 ft; hole 9, 9 ft; hole 10, 10 ft; hole 14, 14 ft; and hole 15, 15 ft. Figs. 1 and 2 show the relationships of the gage and the charge holes. Charges of 80 pct special gelatin, which weighed 50, 100, and 150 g were exploded in the charge holes and the seismic waves were recorded. All charges were stemmed with 200 g of mud and detonated with an electric blasting cap. Fig. 3 shows the recorded seismic waves. The reflected components of the waves were too weak to be objectional on these records. Table I shows the data taken from the wave forms. The approximate average velocity of a wave with a 9-ft travel distance was 12,900 fps. Since different charge weights were used, it was necessary to scale the data. The scaled maximum compress ion-strain data and the scaled maximum tens ion-strain data are shown in Figs. 4 and 5, respectively. Figs. 6 and 7 show the strain-distance data from Figs. 4 and 5 converted to a 1-lb charge. The results showed that the wave consisted of an initial compression pulse followed by a tension pulse. The amplitude of the tension pulse approached the amplitude of the compression pulse as the distance between the gage and the shot increased. The decay rate of the seismic wave is very important in the evaluation of the blasting characteristics of a rock. When high-amplitude stresses are produced, as in rock fragmentation, the rate of decay is much more rapid than when small amplitude stresses are produced. In underground mine blasting, the burdens are usually not greater than 6 ft and the decay is very rapid. The rapid seismic-wave decay rate in the fragmentation range means that in practice, if the minimum weight of powder is used to break a specified burden, only a very

Jan 1, 1961

By S. E. Bronisz, R. E. Tate

s-plutonium samples possessing a strong growth texture have been produced by allowing them to transform under pressure from p to a. A fiber texture with [010] parallel to the pressure axis results. The textured samples are expected to be useful in determining the effects of crystallographic orientation on the physical properties of a plutonium, and initial results of measurements of resistivity and mechanical properties are described. THE crystal structure of a plutonium1 is mono-clinic, P21/m, and many of the metal's properties should reflect the crystallographic anisotropy. Unfortunately, it has not yet been possible to grow useful sizes of single crystals of a plutonium. Therefore, few of plutonium's orientation-sensitive properties have been determined as a function of crystallographic orientation. One way to gain information about at least some of the orientation-dependent properties is to study a highly textured sample. Such samples have been produced by cold rolling a plutonium,2 but they are necessarily very small in one dimension. We have now successfully used two other techniques to produce highly textured samples, not limited to small thicknesses. METHODS OF PRODUCING PREFERRED ORIENTATION The texture is produced by causing the plutonium to transform from ß to a while under pressure. It was observed by Gardner3 that applying a compres-sive load during the transformation resulted in the formation of columnar grains of a plutonium, and Cramer4 observed a similar structure in some diffusion couples rolled in the P phase. Neither of these workers, however, investigated the subject beyond these observations. The more flexible of the two methods developed is that of compressive loading. The technique is to enclose a sample of plutonium in a die assembly before applying the load. It is possible, of course, to dispense with the die and simply press the sample between two platens. In this case, however, the unrestrained sample deforms during the pressing, making it difficult to maintain the load and to control the final sample thickness. This compressive loading technique has been used on specimens ranging from 1/4 to 3 in. diameter, with height-to-diameter ratios ranging from 5 : l to 1:6. The procedure begins with loading the sample, a right cylinder of a plutonium, into the pressing die. Plastic deformation of the sample while it is being pressed is minimized by machining the sample so that its diameter is nearly the same as that of the die barrel. Then the loaded die assembly is placed in a vacuum pressing can that fits on a hydraulic press. After a vacuum is achieved the die assembly is heated to 180°C and equilibrated. The load is then applied and the specimen and die are allowed to cool to about 40° to 50°C before the pressure is removed. The resulting sample is composed of rod-shaped a -plutonium grains, the rod axes being parallel to the cylinder axis and the pressing direction. Photomicrographs of the oriented structure are shown in Fig. 1. Although most of the specimen is composed of grains whose rod axes are parallel to the cylinder axis, a thin, peripheral layer consists of rod-shaped grains whose rod axes are perpendicular to the cylinder axis. Presumably, the highly plastic nature of p plutonium leads to approximately hydrostatic conditions during the initial stages of the P — a transformation under pressure. At this time, the grains in the peripheral layer would have grown parallel to the local force direction. During the latter stages of the transformation, the accompanying volume contraction would have eliminated the radial forces, leaving only the axial force and resulting in the growth of the observed structure. The growth texture did not form without the application of pressure. Attempts were made to produce the texture by repeating the standard temperature cycle without

Jan 1, 1965

By Harold L. Overton, Leonard B. Lipson

The first paper in this series1 outlined practical methods for applying the theory of steady-state flow of an ideal Bingham plastic liquid through a circular pipe and axially through a stationary concentric annulus to the enginekring analysis of friction loss problems. In the present paper the properties of another useful rheological model, the pseudoplastic generalized Newtonian liquid, are considered. The terminology applied to the rheological models is derived from the following classification of rheological models. The term "generalized Newtonian" is a class designation applied to models which do not have yield points but which exhibit a dependence on shear rate. The term "pseudoplastic" applies to a sub-group of models within this class which exhibit a decrease in "viscosity" with increasing shear rate. The term "power model" refers to a mathematical model proposed for describing the behavior of the pseudoplastic liquid. This model is of interest since certain of the salt saturated, oil emulsion, and "low solids" drilling fluids, inverted emulsion- and oil-base drilling fluids, aqueous gels, gelled crudes and blocking agents employed in hydraulic fracturing operations are of this type. The present treatment considers the equations describing steady-state Poiseuille flow through a circular pipe and a stationary concentric annul us, and Couette flow between concentric rotating cylinders for a particular pseudoplastic model. As in the previous paper' it is demonstrated how these equations can be applied to engineering calculations of friction losses. Graphical procedures for recovering the various flow curves and cxample calculations are included. A method for simplifying turbulent-flow correlations is also proposed. PROPERTIES OF PSEUDOPLASTIC GENERALIZED NEWTONIAN LIQUID In contrast to the Bingham plastic the generalized Newtonian liquid is yield point-free. However, in the flow region the relation between stress and rate of shear is not linear as it is with ordinary Newtonian fluids. If the stress increases with shear rate at a less than linear rate the system is called pseudoplastic. While there is no yield point in this system, the Bingham advocates' coined the term pseudoplastic to distinguish this kind of behavior from Bingham plastic behavior. For the pseudoplastic a plot of flow rate vs friction loss or rpm vs torque, from pipe flow or rotational viscometer measurements, respectively, generally has three qualities: (1) it can be clearly extrapolated toward the origin; (2) there is very little slope at the origin. This accounts for the high apparent viscosities at low mixing and pumping rates; and (3) the flow curve possesses a continuous curvature which gradually diminishes as the shear increases. Rheological measurements on a pseudoplastic liquid can be easily misinterpreted as indicating Bingham plastic behavior. A typical case in point is illustrated in Fig. 1. These data were obtained from measurements on an oil-emulsion mud using a commercially available rotational-type viscometer (Model 35 Fann V-G meter). Applying the "two-point"* method3 gives a plastic viscosity of 17 cp and a yield point of 24 lb/100 ft2; at the same time weighting material settles very easily in this system. This illustrates that it is not possible to distinguish between the pseudoplastic and the Bingham plastic from only two data points. It is possible to determine qualitatively which model is more appropriate by a combination of dynamic and static measurements. Experience indicates that the simplest criterion for the Bingham plastic liquid is that the calculated dynamic yield point should be of the same magnitude as the measured gel strengths. For the oil-emulsion drilling fluid illustrated in Fig. 1, a value of 4 lb/100 ft2 was obtained for gel strengths measured

By AIME AIME

A LUSTY baby of the Institute, the Coal Division, showed that it had acquired a full set of teeth and was capable of man's work at the Division meeting at Fairmont, W. Va., on March 26 and 27. At this second of a series of field meetings, the first of which was held in Pittsburgh last fall, the industry in the East was represented from top to bottom and good humor and enthusiasm were the predominant notes. West Virginians are always good hosts and this meeting would have proved the statement to any inclined to doubt it. The spacious auditorium of the Fairmont Hotel was arranged for the technical sessions, the hotel being headquarters for the meeting. About a hundred and twenty-five representatives were registered and in attendance when Thomas G. Fear, chairman, opened the morning session at 10 o'clock Mr. Fear first introduced Howard Eavenson, vice-chairman of the morning program, who, as chairman of the Coal Division, had labored long and cheerfully to make the meeting successful. Mr. Eavenson talked briefly on what the organization was doing, pointing out that these field meetings were designed to bring the members into closer touch with the parent Institute and give the younger engineers in the field a better opportunity to participate in the work the Institute is doing. He congratulated the various committees for their work in promoting the meeting.

Jan 1, 1931

By E. J. Dulis, A. Kasak, R. C. Westgren

The potential of uirought tungsten- and tantaluw-rich alloys of the W-Ta-Mo-Cb system was investigated for high-strength structural applications above 2500° F. Appreciable strengthening of tung-sten and tantalum—essentially attributable to solid-solzction effects—was obtained with binary, ternary, and quaternary alloys. Tensile strengths as high as 67,000 psi were achieved at 3000 OF. ThE quest for wrought structural materials which possess good strength properties at temperatures above 2000°F has led to a considerable research effort during the past decade. In addition to exploring the potential of various high-melting-point refractory metals (such as molybdenum, columbium, tantalum, and tungsten) for very high-temperature structural applications, alloy-development programs have been undertaken to achieve greater strengths than could be achieved with unalloyed refractory metals. The methods of strengthening refractory metal alloys have included both solid-solution and dispersion strengthening. General relationships among the relevant properties (melting point, recrystallization temperature, and high-temperature strength) of refractory metals indicate that the highest strengths at temperatures of 2500°F or higher would be obtained with tungsten-or tantalum-base alloys. Therefore, the present investigation was undertaken to determine the high-temperature strength potential of solid-solution strengthened alloys based on the binary system W-Ta; to effect further strengthening, minor additions of molybdenum and columbium (at the 6 and 12 pct levels) were made. The portion of the W-Ta-Mo-Cb quaternary alloy system of interest is shown schematically in Fig. 1. The component metals—W, Ta, Mo, and Cb—have a bcc structure at all temperatures, and their binary systems are mutually completely soluble.' Complete solid solubility in the W-Ta-Mo and W-Ta-Cb alloy systems has been demonstrated,' and, therefore, it was expected that the quarternary alloys of the system would also exhibit complete solid solubility at all temperatures. In the virtual absence of contamination by interstitial elements, all the alloys would be truly solid-solution strengthened. Twenty specific compositions of this investigation included binary, ternary, and quaternary alloys of the W-Ta-Mo-Cb system as well as unalloyed tungsten and tantalum. The compositions are shown in Table I. EXPERIMENTAL PROCEDURE Consumable-electrode vacuum-arc melting with ac power was used to produce small laboratory-sized, cylindrically shaped ingots (1-1/4 in. in diameter and 2 to 3-1/2 in. long) of the twenty compositions. A furnace was specially constructed to melt as many as four electrode rods simultaneously into molds lined with tungsten or tantalum sheet. High-purity rods of tungsten, tantalum, molybdenum, and columbium were used for consumable electrodes; the diameter of each rod was determined by the desired weight percentage of the component metal in a given alloy. The details of the construction and operation of the melting furnace will be discussed in another p~blication.

Jan 1, 1964

By AIME AIME

THE graduating class whom I am particularly addressing are going into the world at least a month earlier than normal, because of the war. You have been free to choose your work. You have chosen to be mining engineers. The principal importance of your engineering education to date has been in teaching you how to think and how through books to have ready access to the accumulated experience of previous generations, as well as the current experience of the day. You should by now have acquired something of the engineering point of view, the open skeptical mind. the power to observe, experiment, and draw conclusions, form theories and test these by further experiment, and weigh the inherent probability of conclusions drawn by others. I am asking you today to consider certain facts and the conclusions I am drawing from those facts.

Jan 1, 1942

By R. L. Wilcox, M. L. Fuller

Most commercial alloys undergo changes in phase composition after casting. This is a natural result of the fact that the alloys are not in a state of phase equilibrium as cast and phase changes will therefore take place, with more or less rapidity, in an attempt to attain equilibrium. The practical aspect of aging in zinc-Alloy die castings concerns the changes in physical properties and in dimensions that may accompany aging phase changes. Harmful alterations have been reduced to a minimum and zinc-alloy die castings are being produced today that are so stable with respect to dimensions and physical properties that they are entirely suitable for most practical purposes1. In the first paper2 of this series, and in this paper, aging phase changes of zinc-alloy die castings have been investigated and the possible influence of these changes on dimensional changes of the castings has been evaluated and compared with the dimensional changes actually experienced. The change of dimensions has been selected for practical comparison in these papers because the effect of phase changes on the dimensions of a casting is directly calculable from X-ray crystal-analysis data of the phase structure. The die-casting alloys considered contain, in addition to zinc, 4 per cent of aluminum, about 0.03 per cent magnesium, and from 0 to 3 per cent of copper. It was shown in the former paper that the eutectoidal decomposition of the beta aluminum-zinc phase, while intrinsically capable of causing a considerable shrinkage, can have very little effect on the observed shrinkage of die castings because it takes place within a few days of aging, whereas the observed shrinkage continues for five weeks. It was therefore concluded that the other existing phase change, namely, the segregation of secondary phase from the zinc-base solid solution, must account for the major portion of the shrinkage.

Jan 1, 1936

APPROXIMATELY 26 percent of the total ore production to date from the largest single deposit of copper-bearing material in the world was mined during the war years, 1942 to 1945, at Chile Exporation Company's great open-pit mine at Chuquicamata, Chile. About 18 percent of the total waste removed during the life of the mine was handled in the same period. The total of ore and waste represents approximately 24 percent of the total material that has been excavated from the pit. This is more than was removed in the first fourteen years of operation from 1914 through 1927. The pit at Chuquicamata is 17/8 miles long, 1/2 mile wide, and has a present vertical extent of 817 ft between the top of the highest bench and the lowest bench being worked. However, when

Jan 1, 1948

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster's New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process, or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, "Why automate?" Automation, automatic control devices, and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with the minimum amount of instruments needed merely to guide operators. Processes were manually con- trolled by the operator on the basis of simple temperature, pressure, flow, and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material throughput, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins, or producing a new and salable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure and (2) units which both measure and control a process variable.

Jan 1, 1979

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,' E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940