Search Documents

By Kenneth S. Ritchie

THE discovery well of the world's -deepest oil producing structure, University 1-B of Group No. One Oil Corporation, in the Big Lake oil field, Reagan County, Texas, has had a remarkable record. The well is outstanding for the following reasons: (1) It is the world's pioneer well to produce. oil in commercial quantities from a structure 8500 ft. below the earth's . surface; (2) this well was the only. producer from the 8500-ft. pay for a period of 17 months and 24 days; (3) the flow of the discovery well has been free from-the customary changes at the casinghead, with the exception of putting on a back-pressure of 185 lb.; and, (4) the well's daily production of oil and gas increased rather steadily for 17 months and 18 days from an initial of 40 bbl. per day to a maximum of 2926 bbl. per day, and then six months later, after a period of decline and self-readjustment to subsurface changes caused by six more deep producers, the well set its real record for one day's production of oil at 2950 bbl

Jan 1, 1931

By B. Egeberg

IN A previous paper1 the authors dealt with the physical properties of cold-rolled and heat-treated Britannia metal of the approximate composition Sn, 91 per cent., Sb, 7 per cent. and Cu, 2 per cent. It was found that cold rolling to more than 50 per cent. reduction produced a continuous softening of the metal when measured by the Brinell machine, whereas the Shore instrument indicated increased hardness; that the strength of the material followed the Brinell hardness and that the metal therefore became weaker the more it was cold-rolled; and further, it was found that hardness and strength could be largely restored to the cold-rolled metal by "baking" for about one hour at any temperature, between 200° and 450° F., the melting point. The higher the baking temperature, the more effective was the heat treatment as far as increased hardness was concerned. It seemed to be of little importance whether the metal was soaked or not at the baking temperature for a great length of time and the rate of cooling seemed to be immaterial. The present paper deals with the same alloy and more particularly with the resistance towards various forms of stress - tensile, bend and deep drawing. The metallography of Britannia metal has in part also been covered and an explanation attempted for the abnormal behavior of this alloy.

Jan 1, 1929

By H. S. Bell

IT SEEMS unnecessary to dwell upon the advantages of the modern pipe still as compared with the older type of distillation equipment used by oil refiners. The relatively low installation cost, coupled with remarkable operating efficiencies of pipe stills, precludes the consideration of other types except in rare instances where some peculiarity of product or plant may have an influence. The question of the actual heat required to distil petroleum is quite involved. We have extensive data on the latent heats of the various hydrocarbons under different conditions of pressure. We also have information regarding the specific heats of various oils and the effect of temperature thereon. Because of the complexity of petroleum and of each fraction, it seems impossible to theoretically analyze the partial-pressure effect of the great number of hydrocarbons upon one another during distillation. If a distillation curve and percentage analysis of any crude or product are available, it is possible to construct a curve with ordinates representing per cent. distilled and B. t. u. per pound or per gallon, or other desired unit. To do so the crude is split into fractions, of 5 or 10 per cent. The boiling point and gravity of each fraction being determined, it is possible to evaluate the heat required. As each fraction is removed, the residue must be raised to a higher temperature and latent heat supplied for the successive fraction. As the calculations progress, the latent heats decrease while the specific heats increase. Such a curve is illustrated by Fig. 1 for a typical 39.9 B° North Texas crude.

Jan 1, 1928

By Richard T. Newcomb

Federal and utility industry research has largely ignored coal beneficiation techniques in the implementation of SOx control. This paper accepts the hypothesis that beneficiation cum scrubbing is the cheapest way for the vast majority of seams in the eastern coal provinces to comply with standards. Comparisons are based on point estimates of average beneficiation costs from a model of coal preparation (COBET) designed to simulate four levels of cleaning. The paper describes how economic theory can be applied to derive econometric supply functions from actual data on the geology of minable seams, washability and technical constraints. West Virginia is taken as an example of a producing region. Spatial supply functions are derived empirically from the engineering model simulations.

Jan 1, 1977

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 ½ times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.1,2 Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.4 Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the caprock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1952

By E. J. Roberts, E. B. Fitch

THE mechanism of classification by settling pools is most simply shown in the case of batch sedimentation such as was analyzed by Oden.1 The batch model will be considered, therefore, and it will be shown that the same mechanism applies to continuous operation. Classification in Batch Settling Pools: Consider a beaker or tank of slurry containing particles so dispersed that they can settle independently of one another under the influence of gravity. Originally all particle sizes are uniformly distributed throughout the suspension. All particles start immediately to settle towards the bottom at rates determined by their size, shape, and density—among other factors. Particles reaching the bottom settle out of suspension. After some given time the slurry above the deposited solids is siphoned off or otherwise removed, leaving the deposited solids behind. The deposited solids, together with entrained and any unremoved supernatant slurry, represent the underflow of a classifier. The slurry removed represents the overflow. There is a certain separation, size of particle which during the sedimentation has just time to settle from the top surface of the slurry to the level at which underflow and overflow are parted. All particles with a faster settling rate will have dropped to below this level, no matter where in the beaker they started from originally, and therefore will be absent from the overflow. Particles with a slower settling rate will not reach this level if they started from the top of the slurry, but a portion of them,

Jan 1, 1957

By A. E. WALKER

SOME eighty years have elapsed since the discovery of the Clifton magnetite deposit. For a few years about the time of the Civil War it was mined for iron ore. most of which was smelted on the property. Since risen the small exposures of ore in the old cut. test pits, and on the dumps have been examined by various prospectors. The M. A. Hanna Co. first became interested in the possibilities of the deposit when we discovered the large area of strong magnetic anomalies caused by the margnetite bed, indicating a size that would support a commercial operation. In 1940 we made a detailed magnetometer survey of the area. and the deposit was diamond-drilled. The main ore lied was found to be 1500 ft. long, to average 60 ft. thick, and to dip southeast at an angle of about 40 deg. The thickness of the bed is irregular in wavy folds both along the strike. and down the dip. Faults occur at both raids of the main deposit.

Jan 1, 1943

By AIME AIME

A PAPER recently presented before the Anthracite Section of the A. I. M. E. by S. J. Phil- lips, Mine Inspector, Fifth Anthracite District, Department of Mines of Pennsylvania, covering the water hazards in the anthracite coal mines of the Lackawanna River Valley, was especially timely because the conditions there are duplicated to a large extent in the Wyoming Valley, which is traversed by the Susquehanna River with its many large tributary streams. Also, in the southern anthracite field, where there are a number of large creeks, similar pumping problems and mine water hazards will in time be presented if mining is continued to its conclusion.

Jan 1, 1936

By Frank Milliken

IN September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1007 to 1019. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was dissemi-nated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was prob-ably less than 6o per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a com-plete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof com-prised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. 1, which gives percentages of tonnage and copper content.

Jan 1, 1940

By R. E. Cech

Metallographic observations on hydrogen-reduced nickel oxide crystals suggest that nucleation of nickel occurs at structural singularities in the oxide. The fully reduced structure contains micron-diameter, worm-like voids occupying 40 to 50 pct of the volume. The crystallographic orientation relationships between nickel oxide and nickel resulting from oxide reduction are recorded and discussed. THE process of reduction of oxide to metal is one of considerable complexity involving a chemical reduction reaction, mass transport of reducing agent to the point of reaction and of reaction product away from it, and finally a transformation whereby metal atoms released from the oxide rearrange to form a stable reduced phase. In addition, nucleation of the reduced phase affects the overall reaction kinetics. Thus far only the thermodynamic aspect of reduction has received the attention warranted by the importance of

Jan 1, 1960

By E. C. Potter

FUEL-OIL was first substituted for coal at these works in September, 1888. It was first applied in the converting-department to the battery of boilers, consisting of 14 tubular boilers, 16 feet in length by 5 feet in diameter. To operate these boilers with coal for 24 hours required 14 strikers, 3 ash-wheelers, 6 men unloading coal, and 2 water-tenders, making a total of 25 men. With fuel-oil the same boilers require for the same period 2 water-tenders and 4 men to attend to the burners, making a total of 6 men. This gives a saving of 19 men, which, at an average of $2 per day each, amounts to $38 per day. Comparing the consumption of oil with that of coal, we find that for the week ending January 5, 1889, with an ingot output of 6403 tons, 2731 barrels of fuel-oil were used as against a necessary consumption of coal for the same work of 848 tons, showing 3.22 barrels of fuel-oil to be equivalent to one ton of Indiana block-coal. Figuring oil at 60 cents per barrel, and coal at $2.15 per ton, we have as the cost of oil $1.93, as against $2.15 for its equivalent in coal. In December, 1888, the rail-mill battery of 26 boilers, of the same dimensions as those in the converting-department, was equipped for fuel-oil. For the week ending January 5, 1889, with a rail out-put of 5208 tons, 5987 barrels of oil were consumed, as against a necessary consumption of coal, to do the same work, of 1805 tons, showing 3.31 barrels of fuel-oil to be equivalent to one ton of Indiana block-coal, which at the costs named above would show $1.98 worth of fuel-oil to he equal to $2.15 worth of coal. The labor required to operate the rail-mill boilers for 24 hours, with coal as fuel,is: 26 stokers, 4 water-tenders, 6 ash-wheelers, 12 men unloading coal; total, 48 men. With oil as fuel, the same work requires 4 water-tenders and 6 men to attend to the burners; total, 10 men; a saving over coal of 38 men in 24 hours, which, at an average price of $2 per day, would be $76 per day. In the brief experience we have had with oil as fuel, we find that the efficiency of the boilers is somewhat increased and the repairs are

Jan 1, 1889

By R. R. Vandervoort, W. L. Barmore

Tensile creep experiments were conducted on high-purity, poly cvystalline rhenium from 1500" to 2300°C at stresses from 1500 to I0,OOO psi in a vacuum of 10-a torr. The apparent activation energy for creep was 60 kcal per mole, and the steady-state creep rate varied directly with stress to the 3.4 power. Dislocation substructure that developed during creep was studied by transmission electron microscopy. Possible rate-controlling deformation mechanisms are discussed. The creep behavior of most metals at elevated temperature can be represented by the following equation:&apos;&apos;&apos; t = Cf(s)(^)(s/E)nD [1] where i = steady-state creep rate, C = constant, f(s) = a function involving microstructure, s = applied stress, E = the average elastic modulus at test temperature, n = constant, D = diffusion coefficient According to this well-established relationship, metals with higher elastic moduli and lower diffusion coefficients should have greater creep resistance at the same stress and temperature and equivalent mi-crostructures. While no diffusion data are available, the diffusivity of rhenium should be less than that for most other refractory metals because of its high melting point and hcp crystal structure. The Sherby-Simnad relation for calculating atomic mobility in metallic systems3 predicts that the diffusion coefficient for rhenium is less than that experimentally determined for tungsten4 in the temperature region 1500. to 2200°C. At these temperatures the elastic modulus for tungsten5 is only slightly larger than the extrapolated modulus for rhenium.6 Thus, rhenium is a good possibility for a a high-temperature structural material, but few data on the creep of rhenium have been reported. This investigation was undertaken to study the high-tempera-ture deformation behavior of rhenium in detail. EXPERIMENTAL TECHNIQUES The material used in this study was consolidated from high-purity powder. After cold pressing the powder to a plate a in. thick, the billet was sintered in hydrogen at 2250°C for 24 hr. The plate was reduced to 0.100 in. by cold cross rolling with intermediate anneals at 1650°C for 20 min between passes. The plate was further reduced to 0.060 in. by unidirectional cold rolling with similar heat treatments between passes, and then finally stress-relieved in hydrogen at 1650°C for 30 min. Specimens tested at 1900°C and below were pretest-annealed at 1900°C for 2 50 hr. Specimens tested above 1900°C were pretest-annealed at 2400°C for 5 hr. The impurity content in the "as-received" plate was quite low, table I. Essentially no change in impurity levels was detected in specimens after creep testing. All creep tests and annealing treatments were conducted in a vacuum of 10-8 torr in a test furnace heated by a tungsten mesh element. The load was applied to the specimens through a bellows, and stresses were maintained to ±1 pct of the selected value by periodic corrections for changes in specimen cross-sectional area during creep and for changes in the bellows spring force due to load column extension. One-inch-diameter tungsten force rods were used in the hot zone of the furnace. Deformation at temperature was measured by optically tracking gage marks on the specimen. Temperature was measured by a calibrated optical pyrometer and was determined to ±5"C. Grain sizes were determined by the linear intercept method and specimens were examined in the "as-polished" condition, using polarized light. Specimens annealed at 1900°C had a grain size of 52 ± 5µ , and those annealed at 2400°C had a grain size of 148 * 11 µ. Pieces were cut from the gage section of creep-tested specimens and planed to a thickness of about 0.010 in. by spark discharge machining. Thin foils for viewing by transmission electron microscopy were obtained by electropolishing in a solution of 6:3:1 ethyl alcohol, perchloric acid, and butoxy ethanol, respectively, using the window technique. Bath temperature was —4OoC, and the cell potential was 35 v. The foils were examined in Siemens Elmiskop I, operating at 100 kv. RESULTS AND DISCUSSION In order to analyze the results from creep experiments, Eq. [I] is rewritten in the following form: <=Kf(s)ne-/RT [2] where K = constant, ?// = apparent activation energy for creep,

Jan 1, 1970

By Carl M. Fellman

LABOR disputes caused considerable turbulence in the coal mining industry during 1946. As an outcome of these disputes, a definitely fundamental change in safety procedure was instituted: establishment of safety regultions for coal mines through the agency of agreements between the miners&apos; union and the agency or agencies operating the coal mines. Although a temporary plan at present, the future will determine the. extent to which it may become permanent. Notwithstanding the turmoil in the industry extending through much of the year, the safety record for the first eleven months of 1946 was the best in the history of the industry for that period. The fatality rate for 1946 is lower than in any other year in the history of coal mining in the United States. This follows a pattern inasmuch as new low coal-mine fatality records were also made in 1945, 1944, and 1943. The five-year period 1942 to 1946 inclusive has a coal-mining fatality rate far lower than any other five-year period in the history of the industry. It is significant that this period exactly coincides with the operation of Federal coal mine inspection which got under way early in 1942.

Jan 1, 1947

By A. W. Gauger

SMELTING of iron ore, manufacture of steel, and the fabrication of ferrous metal products are all processes that require energy. Charcoal was adequate, to supply this energy for the relatively simple processes of the early iron-masters. In the fourth decade of the nineteenth century, anthracite and bituminous coal and later coke supplanted charcoal for the smelting of iron. So far as the chemical phases of the process were concerned, charcoal was an ideal iron-furnace fuel. It had practically no sulphur, and its ash, besides being low in quantity, consisted chiefly of lime and alkalies, thus supplying a part of the flux required for smelting the ore. The ash of coal and coke on the other hand, being largely silica, had itself to be fluxed with bases added to the charge. Physically, however, coke proved to have many advantages over charcoal, which could not be used in the furnaces of today. The chief reason, however, for the change from charcoal to coke was the impossibility of maintaining an adequate wood supply.

Jan 1, 1941

By Edward Griffith

The anthracite industry, which produces about 50 million net tons of coal annually, has been talked of as being able to last for another century; but if the water record of the past century continues into the expected century, this expectation of many years production still to come out of the remaining reserves will not be attained. The industry will be a submerged one in fact as well as in name. A recorded forecast of what has since occurred appears on page 34 of the Mine Inspectors&apos; reports of 1897: It should also be noticed that bodies of water had accumulated in parts of abandoned mines before duplicate surveys of the same were required by law; and as a result we have today to contend with bodies of water, the exact location and position of which are not correctly known. Since that date, 47 years ago, the implications of the foregoing comment have grown enormously. This is shown in Fig. I and in the following table showing flooded and partially flooded areas that have come into existence since the early 1930&apos;s in the northern anthracite field: Number of Year Flooded Areas 1932...................... 2 1933...................... 3 1934..................... 3 1935...................... 5 1936...................... 7 1937...................... 9 1938.................... 11 1939...................... 11 1940...................... 11 1941...................... 14 1942...................... 14 1944...................... 26 Similar conditions exist in other fields in the anthracite region. In the period between 1923 and 1940, abandonment of collieries in the southern field resulted in the flooding of approximately 60 sq. miles (30 per cent) of the field. The ahandonment of collieries in this field has imposed additional expense for pumping on the collieries still operating. This condition will be aggravated by the extension of developments and cause suspension of operations if economic conditions do not justify the assumption of additional pumping costs. During the years, the region&apos;s rainfall has not altered, but the quantity going inside the mines through breakages in the surface, brought about by extraction of the coal, has increased materially, as indicated by the ratio of tons of water pumped to tons of coal produced underground for one of the large companies in the northern anthracite field: Year Ratio 1920................. 8.4:1 1925.................. 10.6:I I930.................. II.4:I 1935................. 26.2:1 1940.................. 32.7: I 1942.................. 30.3:I The data in Table I shows the total amount of water pumped and its ratio to underground production for one of the large companies in the southern anthracite field, and shows a rapidly growing serious situation. Rainfall quickly affects the workings in all the fields. In mine inspection district 7 of the southern field the rainfall in 1935 was 92,083,000,000 gal. The total water pumped was 36,274,000,000 gal. (39.4 per cent of the rainfall). The operating mines

Jan 1, 1947

By Edward Griffith

The anthracite industry, which produces about 50 million net tons of coal annually, has been talked of as being able to last for another century; but if the water record of the past century continues into the expected century, this expectation of many years production still to come out of the remaining reserves will not be attained. The industry will be a submerged one in fact as well as in name. A recorded forecast of what has since occurred appears on page 34 of the Mine Inspectors&apos; reports of 1897: It should also be noticed that bodies of water had accumulated in parts of abandoned mines before duplicate surveys of the same were required by law; and as a result we have today to contend with bodies of water, the exact location and position of which are not correctly known. Since that date, 47 years ago, the implications of the foregoing comment have grown enormously. This is shown in Fig. I and in the following table showing flooded and partially flooded areas that have come into existence since the early 1930&apos;s in the northern anthracite field: Number of Year Flooded Areas 1932...................... 2 1933...................... 3 1934..................... 3 1935...................... 5 1936...................... 7 1937...................... 9 1938.................... 11 1939...................... 11 1940...................... 11 1941...................... 14 1942...................... 14 1944...................... 26 Similar conditions exist in other fields in the anthracite region. In the period between 1923 and 1940, abandonment of collieries in the southern field resulted in the flooding of approximately 60 sq. miles (30 per cent) of the field. The ahandonment of collieries in this field has imposed additional expense for pumping on the collieries still operating. This condition will be aggravated by the extension of developments and cause suspension of operations if economic conditions do not justify the assumption of additional pumping costs. During the years, the region&apos;s rainfall has not altered, but the quantity going inside the mines through breakages in the surface, brought about by extraction of the coal, has increased materially, as indicated by the ratio of tons of water pumped to tons of coal produced underground for one of the large companies in the northern anthracite field: Year Ratio 1920................. 8.4:1 1925.................. 10.6:I I930.................. II.4:I 1935................. 26.2:1 1940.................. 32.7: I 1942.................. 30.3:I The data in Table I shows the total amount of water pumped and its ratio to underground production for one of the large companies in the southern anthracite field, and shows a rapidly growing serious situation. Rainfall quickly affects the workings in all the fields. In mine inspection district 7 of the southern field the rainfall in 1935 was 92,083,000,000 gal. The total water pumped was 36,274,000,000 gal. (39.4 per cent of the rainfall). The operating mines

Jan 1, 1947

By John B. Hastings

THE occurrence of such a large amount of gold in the Hartsel granite, even though the surmised existence of similar areas is not new, brings freshly to mind the pegmatite type of magmatic differentiation lately brought again to attention by occurrences at Silver Peak, Nev., described by Spurr; and in Alaska, described by both Spurr and Brooks. In both localities graunitic rocks or dikes are thought to pass into metalliferous quartz-veins. An interesting association in this connection is the occurrence of diamonds in residual pegmatitic clay of San Juao de Chapado, Brazil, described by Derby :1 (P. 142) "Bodies of pegmatite are quite common in the older rocks of Brazil, both in the. diamond regions and elsewhere, occurring not only in the gneiss and granite, but in the schistose series as well. Those that have been examined are dike-like in their mode of occurrence and granitic in composition." (P. 143) "The question of the eruptive or secretionary origin of pegmatites has long been a subject of discussion among geologists. . . . The recent studies . . . seem to have clearly established that most if not all of them are essentially eruptive masses, though possibly modified in some way by aqueous agencies. Even before becoming acquainted with the literature of the subject this view had seemed to me to be the only acceptable one as regards the typical pegmatites of Brazil." What is pegmatite ? J. F. Kemp says ". . . veins or dikes-it is an open question which is the more correct term-are met formed of very coarsely crystalline aggregates of the same minerals that constitute granite. These are called pegmatite and in them is the home of graphic granite, the curious intergrowth of quartz and feldspar, such that a cross fracture of the blades of quartz suggests cuneiform characters. . . . In regard to the larger veins or dikes it seems improbable that true igneous fusion could have afforded such coarsely crystalline aggregates, and so we are forced to assume such abundance of steam and other vapors, i.e, mineralizers, as to almost, if not quite, imply solution."

Jan 5, 1908

By AIME AIME

DREAMS do come true at times, although it is evidently better to believe in engineers than to "believe in fairies" if most dreams are to be translated into fact. It was a fine dream that David H. Moffat had when he projected a railway directly west from Denver; a dream of opening a new empire in northwestern Colorado, and of quickening transportation from the Middle West to the Pacific slope. But Moffat had been a miner and had become a banker. He knew that dreams, untranslated into works, benefit no one and pleasure only the dreamer, so he employed an engineer, H. A. Sumner, to study and plan the route to be followed by the rails. Previous main lines had run to the north, the Union Pacific, or the south, the Santa Fe. The Denver and Rio Grande, it is true, wriggled its way bravely across Colorado but, in order to reach a point 74 miles in an airline west of- Denver, travelled 281 miles following two canyons and crossing Tennessee Pass at 10,240 ft. Valuable as such a road is, it could never accomplish what Moffat had in mind. It was known that no low pass could be found directly west of Denver but up to 9000 ft. the topog-

Jan 1, 1925

By E. L. Dougherty, J. W. Sheldon

A numerical method for computing the dynamical behavior of fluid- fluid interfaces is described. Results of studies made to assess the accuracy and economy of the method on a computer are reported. It is concluded that it is practical to obtain digital computer solutions for fluid- fluid interface problems with two space dimensions. PROBLEM DEFINITION We consider two-dimensional flow in a rectangle as shown in Fig. 1, where a fluid-fluid interface divides the rectangle into two regions. The pressure is specified along the lower boundary (the injection boundary) and upper boundary (the withdrawal boundary). There is to be no flow of fluid across the side boundaries, which are walls of symmetry for the flow, and px = 0 along these boundaries. The fluids are incompressible, the absolute permeability and porosity is constant, and each fluid has its own constant mobility. Thus, the pressure satisfies Laplace&apos;s equation in each region. Across the interface, pressure is continuous and the normal component of fluid flux is 1. These conditions are shown in Fig. 1. The velocity of a point on the interface in the direction of the normal from Fluid 1 into Fluid 2 is U,/ Q, where Un is the normal component of volumetric flux at the point on the interface, i.e., For brevity, we call the problem defined above "Problem A". Problem A is a simple example of a dynamical fluid-fluid interface problem. However, the same numerical methods which we use to solve Problem A can be extended to the solution of a large number of fluid-fluid interface problems which are mathematical models for various oil recovery processes,l hence our interest in Problem A. We define the interface by prescribing the x, y coordinates of a finite set of points. These points are called "interface mesh points" and are illustrated by triangles or asterisks in the figures. Fig. 2 is a procedural (flow) chart displaying the main steps in the solution. We comment briefly on some of these steps in this section and then give further details in subsequent sections. For mobility ratio greater than one it is well known that Problem A is unstable.*2 Small amplitude,

Jan 1, 1965

By B. L. Landrum, P. B. Crawford

The rise of a new laboratory model for studying tran-sient fluid flow problems, is described. The theory of he model is based on the analogy between the equa-ions which describe the flow of compressible fluids in porous media and the conduction of heal m solids. The "thermal model" is used to study the Iransient Pressure distributions during fluid displacement in five Standard well patterns. The studies indicate quantita-ively how die pressures change with lane at any poit in the reservoir. It was found that, in general, the equipressure contours are more radial about the wells early in the program than after steady-state conditions are established. In addition two studies of fractured five-spot patterns are presented to illustrate the opplicability of the model for a wide range of reservoir conditions. INTRODUCTION In reviewing the oil recovery techniques involving fluid displacement it was found that a very considerable quantity, if not all of the fluid within the pattern, mav be displaced (during a time-dependent or transient period rather than the usually applied steady-state conditions. Since the oil is displaced during a transient period, it was believed desirable to study the nature of the transients for several of the commonly used fluid displacement patterns. A literature review indicated fairly complete studies of the streamlines and isopotentials for steady-state: yet few data were available on the transient displacement process. Several simulated steady-state multiwell displacement programs were carefully mapped by Foster and Lodge on an electrical conducting sheet as early as 1875, hut the more recent work of Muskat provides the best source for steady-state phenomena having direct petroleum production applications. In order to study the transient phenomena a new lab-oratory model was developed which is based on the similarity of the equations that describe the flow of fluids and the conduction of heal. The equations describing heat flow were developed early in the nineteenth century. Regorous solutions tor most transient problems are in gcneral complex and usually limited to fairly restricted houndary conditions.2 the thermal model may be used to obtain approximate solutions for many transient problems without some of the restrictions required for analytical solution. The application of the analogy between heat conduc-. tion in solids. electrical flow and fluid flow, in a porous media has long been recognised. Techniques originally developed for the solution of heat conduction prol?lems have in many instances proved useful in ohtaining solutions to fluid flow prohlcms. Ir is not surpri5ing then that a heat conduction or thermal model might bf usefull in sludying transient fluid flow. As an example ol the problems suitable for the study with the thermal model, transient pressure distributions during fluid displacement programs are studied for the five-spot, line-drive, staggered line-diibe. seven-spot 211 two fractured patterns. A model was constructed of an iron plate of geometry similar to the reservoir patterns under study. The principle of mirror images as suggested by Bryan was employed in shaping the model. A temperature differential was obtained by soldering two sections of copper tubing to the plate at points analogous to the well location in the field. Hot and cold water was passed through the tubing. The temperature distribution, analogous to the pressure distribution in the field. was obtained a a function of time from thermocouplcs distributed over the plate.