Search Documents

By Oscar Weiss

An aerial magnetometer survey was carried out by the author's geophysical organization over the Vredefort dome, where Witwatersrand beds are wrapped around a granite plug 25 to 30 miles in diameter. The well- known magnetic shales of the Lower Witwatersrand system (to be referred to as LWW) give strong negative anomalies over the out-cropping portion of the dome. This is unusual as these same shales -cause positive anomalies over large areas near Johannesburg and along a strike of 130 miles between the East Rand and Klerksdorp. It is suggested that the negative polarization is caused by heat and stresses connected with the doming. This negative polarization of sedimentary beds, which usually cause positive anomalies, is a good example of how "magnetic lows" can be caused by "structural highs." Significant magnetic anomalies should be tested by gravity and seismic methods irrespective of the sign of the anomalies.

Jan 1, 1949

By Edward H. Robie

MANY engineers currently are working harder than usual, in part because of the demands being made upon them for increased production in the war effort, and in part because engineers are in short supply so that there is more to do for those who are available. In some instances the question has come up as to what additional payment, if any, should properly be made for overtime work, and to what extent is such payment legally permitted under the rules of the Salary Stabilization Board. Most engineers employed in an executive, administrative, or outside salesman capacity are not paid for overtime. They are paid for doing a job instead of for the hours they put in, and are free to do all the unpaid home work they feel they should do after dinner, as well as to do a bit of thinking and worrying during wakeful hours in bed. But engineers employed in a strictly professional capacity normally have standard office hours. Some employers pay for overtime and some don't. Their practice as it existed on Jan. 25, 1951 may be continued. In the absence of such practice at that time, the Salary Stabilization Board says that the engineer may now receive additional compensation up to his straight-time rate for an extended work week. No formal approval of the Board is required. "A professional engineer," in the mind of the Board, "is a person employed in a professional capacity, who, by reason of his special knowledge of the mathematical and physical sciences and the principles and methods of engineering analysis and design, acquired by professional education and practical experience, is qualified to practice engineering." Inducted Engineers A letter from a young man just inducted into the service and fearful that his engineering training is not going to be utilized reached us last week from Fort Riley, Kan. The AIME, cooperating with the other Founder Societies, is doing what it can, through the Engineering Manpower Commission, to see that engineers are not being wasted in the military establishment. So we passed this young man's letter along to T. A. Marshall Jr., executive secretary of that Commission. Mr. Marshall tells us that the normal procedure now being followed by the Army in handling Selective Service inductees is to have them first complete 16 weeks of basic training before assignment to specialized categories. During that time they are classified. If one has an engineering degree he should be classified as scientific and engineering personnel at the end of the basic training period. He should then be transferred to a technical detachment and assigned an MOS (Military Occupational Specialties) reflecting his education. If a young man is looking for a commission, it might be added that the current policy in the Army is to transfer to OCS (Officer Candidate School) applicants for commissions in the infantry only. The local unit commander can give information on this point, based upon the aptitude shown in tests. In view of the current shortage of engineers, it is believed that a young man should seriously consider remaining in enlisted status unless he can obtain a commission in a branch of the service that can make full use of his technical skills. His work may thus be more to his liking even if his uniform is not. New York or Atlantic City? In which place is it preferable to hold the annual meeting of a professional society like the AIME-New York or Atlantic City? That is, a winter meeting. The American Society of Mechanical Engineers has held its recent meetings at Atlantic City, with increasing attendance and satisfaction. The American Institute of Chemical Engineers chose Atlantic City for its recent December annual meeting. Only twice has the AIME ever met in this famous seashore resort: in 1898 and 1904. Chief advantages of going to Atlantic City over New York are that technical sessions are better attended, there being little else to do there in Winter; the cost to members is less, and hotel facilities are better adapted to a large meeting. As to cost, take a banquet, for instance. The Chalfonte-Haddon Hall, which caters especially to winter conventions, charges about $7 for a banquet dinner of standard quality. A similar dinner at the Statler in New York would cost about $8.50, and about $10.50 at the Waldorf-Astoria. (The charge for tickets is somewhat greater than this because of the cost of music, programs, flowers, and other incidentals.) Rooms, too, are somewhat less at Atlantic City, two in a room being accommodated for about $7 per day each, compared with $7 to $10 at a headquarters hotel in New York. On the other hand, AIME headquarters is put to some extra expense for staff travel, food and lodging, and members living in New York and environs are forced to pay a hotel bill. New York, of course, has more varied amusements to offer, plenty of big stores, and the glamour of a big city. The choice may be discussed at the forthcoming meeting in New York. In the meantime if any reader cares to express an opinion one way or the other we shall be glad to hear it. College Scholarships Most parents of children in the later stages of high school find it necessary to give some consideration to the cost of a college education. Although salaries have increased substantially it seems that the cost of the necessities of life, such as food, housing, and maintaining the family automobile, have gone up even more, so the problem of financing the children's education is as acute as ever. Many overlook the possibility of scholarships, or feel that only a student at or near the top of his class has a chance to get one. As a matter of fact, close to 150,000 scholarships and more than 15,000 fellowships, worth some $42,000,000, are available in 1200 American colleges and universities. Those who are interested should send 55¢ to the Superintendent of Documents, Government Printing Office, Washington 25, D. C. for a 248-page publication just issued by the U. S. Office of Education, entitled "Scholarships and Fellowships Available at Institutions of Higher Education."

Jan 1, 1952

By AIME AIME

PRESIDENT BASSETT'S gavel called the Annual Business Meeting to order shortly after 10 a. m. on Tuesday. On motion of Eugene McAuliffe, reading of the minutes was dispensed with and Mr. Bassett read his annual report of the year's activities as follows : During the year I have visited eighteen of the twenty- seven sections, making an average of GG 2/3 per cent. The invitation to come again has always been extended, but in only one case have I been able to visit the same section twice. Chicago entertained the president twice during 1930. Mrs. Bassett accompanied me on visits to ten sections. Everywhere we have found the most cordial hospitality and a gratifying enthusiasm for the Institute. If anyone had fault to find with the management or felt dissatisfied with what was being done, it was carefully concealed. I am happy to report to you an agreeable, helpful and progressive spirit in each of the sections visited.

Jan 1, 1931

By T. R. A. Davey

IN 1947 the author became interested in the fundamental aspects of the desilverizing of lead by zinc, conducted some experimental work, and searched the technical literature for all available fundamental data. Since then a revival of interest in the subject in Europe resulted in the appearance of quite a number of papers. It became evident that it would be more profitable to collect together and examine thoroughly the results of various workers, than to attempt to duplicate the experimental determinations. There are many inconsistencies in the various publications, and it is opportune to review at this time the present status of knowledge on the Ag-Pb-Zn system. There is also a need for a clear description, in fundamental terms, of the various desilverizing procedures. This paper is presented in four sections: 1—There is an historical review of the origins of the Parkes process, of the results of many attempts to find a satisfactory fundamental explanation for the phenomena, and of the modifications proposed to date. 2—A diagram of the Ag-Pb-Zn system is presented. This is believed to be free of obvious inconsistencies or theoretical impossibilities, although thermodynamic analysis subsequently may reveal errors. 3—The fundamental bases of the various desilverizing procedures, which have been used up to the present day, are described; and a new method is suggested for desilverizing a continuous flow of softened bullion in which the bullion is stirred at a low temperature in two stages producing desilverized lead at least as low in silver as that from the Williams continuous process and a crust which, on liquation, yields a very high-silver Ag-Zn alloy. 4—A suggestion is made for the revival of de-golding practice, following a recently published account which does not seem to have attracted the attention it deserves. The terms "eutectic trough" and "peritectic fold" as used in this paper are synonymous with "line of binary eutectic crystallization" and "line of binary peritectic crystallization" as used by Masing.' The German literature on ternary and higher systems is rather extensive and a fairly general system of nomenclature has arisen, whereas in English usage the corresponding terms are not as well established. For this reason the meanings of terms used in this paper, together with the equivalent German terms, are given as follows: 1—Eutectic trough—eutektische rinne: line at which a liquid precipitates two solids S1 and S2 simultaneously. If the composition of a liquid which is cooling reaches this line, it then follows the course of this line until a eutectic point is reached, or until all the liquid is exhausted. The tangent to the eutec-tic trough cuts the line joining S1S2. 2—Peritectic fold—peritektische rinne: line at which a solid S1 and a liquid L transform into another solid S2. If the composition of a liquid which is precipitating S1 reaches the line, on further cooling only S2 is precipitated. The liquid composition moves from one phase region (L + S1) into the other (L + S2), and does not follow the course of the boundary. The tangent to the peritectic fold cuts the line S1S2 produced nearer S,. 3—Liquid miscibility gap, or conjugate solution region—mischungslucke: the region within which two liquid phases coexist in equilibrium over a certain range of temperature. A system whose composition is represented by a point in this region comprises one liquid at high temperature; then as the temperature is progressively reduced, two liquids, one liquid and one solid, one liquid and two solids, and finally three solids. 4—Liquid miscibility gap boundary—begrenzung der flussigen mischungsliicke: the line along which the surface of the miscibility gap dome, considered as a solid model, intersects the surrounding liquidus surfaces. 5—Tie lines—konoden: lines joining points representing the compositions of two liquids, a liquid and a solid, or two solids, in equilibrium. In binary systems the only tie lines customarily drawn are those through invariant points, e.g., through the eutectics of the Pb-Zn and Ag-Pb systems, or the various peritectics of the Ag-Zn system, as in Figs. 1 to 3. In ternary systems it is desirable to draw sufficient tie lines to indicate the slopes of all possible tie lines. 6—Ternary eutectic point—ternares eutektikum: point at which liquid transforms isothermally to three solids, S1, S2, and S Such a point can lie only within the triangle 7—Invariant peritectic (transformation) point— nonvariante peritektische umsetzungspunkt: (a) — On the miscibility gap boundary, the point at which two liquids and two solids react isothermally so that L, + S, + L, + S2. (b)—On the eutectic trough, the point at which a liquid and three solids react iso-thermally so that L + S, + S2 + S3. Such a point must lie on that side of the line joining S,S which is further from S,. (c)—A further possibility, not found in this ternary system, is that the point is at the intersection of two peritectic folds when the reaction concerned is L + S, + S, + S Historical Introduction Karsten discovered in 1842 that silver and gold may be separated from lead by the addition of zinc.2 Ten years later Parkes used this fact to develop the well known desilverizing process which bears his

Jan 1, 1955

By C. A. Herbert, C. M. Young

WithIn the past few years, considerable development has been made in the coal-mining industry in Illinois and Indiana and it is the purpose of the authors to record its most important phases. Perhaps the two most striking features are the entry into the producing fields of certain large consumers of coal and the magnitude of some of the new operations. Mines are now being equipped by the Chicago & Northwestern R. R., the Chicago, Burlington & Quincy R. R., the Standard Oil Co., of Indiana, and the Union Electric Light & Power Co. of St. Louis. Besides, the U. S. Steel Corpn. has increased its coal-mining activities by commencing operations on its large holdings northeast of Benton, Franklin CO., Ill. Until recent years, the supply of coal has commonly been adequate and prices have generally been favorable, especially to large consumers, as the magnitude of their purchases enabled them to obtain satisfactory quotations from producers. In fact, most consumers of coal have believed that they could buy their fuel more satisfactorily in the open market than they could produce it themselves. The entry of the United States into the war was accompanied by various disarrangements of industrial conditions, and a demand for coal in excess of the supply seemed likely to be experienced for an indefinite period. Under these circumstances it seemed that the greatest assurance of a supply of fuel was its production by the operation of mines. In the case of the Chicago & Northwestern R. R. and the U. S. Steel Corpn. the production of coal has been carried on for many years with satisfactory results, but the C. B. & Q. R. R., the Union Electric Light & Power Co. and the Standard Oil Co. of Indiana had not been producers of coal, at least in this district. Apparently the most impressive feature of the newest mines is their capacity, for in some cases it is planned that production shall be in the neighborhood of 1000 tons per hr. There are mines now in this field having nearly that output, but these were not planned for such output; in fact, when the shafts were sunk and the machinery installed it was generally supposed that the daily outputs would be only in the neighborhood of 4000 to 5000 tons. Incidentally, there has risen

Jan 1, 1920

By M. B. Hopkins

FOR years the expression "except rubber, tin, and manganese" has appeared in practically every discussion of the natural resources of the United States. Knowledge that natural rubber is not produced in the United States has now spread from the relatively few who have reason to be interested in the country's basic raw material supplies to all those who ride in automobiles, which means everybody. This "everybody" reads in the daily papers that we have a stock pile of natural rubber and that plenty of synthetic rubber is just around the corner. Statistics as to the United States' rubber requirements and sources of supply are of interest to him only to arrive at an answer to the question : "After taking care of rubber requirements for military purposes, will there be rubber for my automobile and the many other rubber articles I want?" More than 30,000 different rubber articles are manufactured in addition to the tires and tubes which use up about 70 per cent of the rubber supply.

Jan 1, 1942

By Hermann Bach, Walther Hänig, Willi Gehrhardt, Ernst Theurich, Walter Langner

With the construction of the Magdeburg zinc works, the Georg von Giesche's Erben Mining Co. of Breslau has to a certain extent completed the program of reconstruction which it set as its goal after the boundaries of Upper Silesia were drawn by the Treaty of Versailles. During its history, covering.more than two centuries, zinc and lead mining has been its chief activity. Through the new boundaries established, it lost to Poland all its mines and smelters, including five distillation smelters. Of its extensive properties, there remained only an apparently unimportant and unexplored portion of the old Bleischarley ore field which, however, happily made possible the resumption of its old business. In 1925 the Deutsch-Bleischarley shaft-only a few kilometers from the old Bleischarley shaft—was sunk and developed, and in May 1926 production of lead and zinc ore was resumed. As facilities for smelting were lacking, the ore was at first delivered to the neighboring smelters, which had now become Polish. Realization of the plan to build its own zinc works had to be postponed at first for lack of capital. In the meantime, however, plans for the new works were worked out in all details. After extensive experimentation in a semicommercial pilot plant it was decided, at the end of 1928 and the beginning of 1929, to use the electrolytic process and, for economic reasons, to place the works at Magdeburg. With zinc at the approximate price level that had ruled since the Deutsch-Bleischarley mine had begun working, it was hoped that the plan could be completed in 1930 with the company's own resources. However, falling metal prices, already noticeable in 1929, made this impossible, and further postponement for a time became necessary. Finally, at the end of July 1933, the funds for building the works became available, in the form of a loan granted under the first employment

Jan 1, 1937

By E. L. Anders

The Mile Six pool is located on the La Brea-Parinas Cullcession of International Petroleum Co., Ltd., in northwestern Peru on the west coast of South America. The reservoir pressure in this pool has been maintained within 200 psi of its initial value throughout its history, and gravity drainage has played an important role in the production behavior. It has now produced 95 per cent of its estimated ultimate recovery. It is estimated that this interesting oil pool will ultimately produce 67 per cent of the initial oil in place and that the resulting residual oil saturation may be as low as 19 per cent of the pore volume (29 per cent of the hydrocarbon pore volume). An evaluation of reservoir rock and fluid characteristics and ultimate oil recovery is presented. INTRODUCTION This study of Mile Six pool was made to evaluate its performance according to latest available information. The production performance of this pool has been discussed in various articles in the past. and the reported behavior has been used as an example for application of computation procedures for gravity drainage depletion' and as an illustration of field behavior under gravity drainage or expanding gas cap drive. There have been wide variations in reported values of initial oil in place, reservoir oil volume factor. connate-water sauration, volume of effective sand, and ultimate recovery because of the paucity of reliable basic data. These various factors have been determined as accurately as practicable with the latest available information, and this evaluation is presented herein. The production history of Mile Six is an excellent example of gravity drainage depleion with effective pressure maintenance by gar injection. GENERAL Mile Six pool was discovered by cable-tool drilling in November. 1927. when well 1996 was completed in the Parinas sand. After slow development with cable tools and sporadic production. the pool was opened to continuous pro(iuction in November. 1933. and develpment was completed with rotary rigs. Pressure maintenance was started in December, 1933. by returning gas to upstructure wells. Most of the development was 'completed by 1937, but some additional wells were drilled in the period 1939-1947. and several old wells were deepened. A total of 46 oil and gas wells and 4 dry holes were drilled on approximately 7-acre spacing. Of the producers. 21 are now flowing. 2 are pumping. 44 are gas input wells. 3 are abandoned. I is a gas well shut in. and 15 are shut in because of non-commercial production or high gas-oil ratio. The locations of all wells are shown on the map of Fig. I. Total oil production on Dec. 31. 1952, was 30,867,373 bbl: cumulative gas production was 22,023,777 Mcf; and 26,410,946 Mcf of gas had been returned to the reservoir. These figures do not include oil and gas lost ill a blowout in January. 1940. GEOLOGICAL DESCRIPTION Mile Six pool is located on the northern end of a structural spur projecting from the La Brea-Negritos uplift.' The spur is probably a reflection of a basement structure. It plunges gently to the north, i broken into a complex series of fault blocks. and contain.; the Verdun Alto. Section Sixteen. and Mile Six pools. The Parinas handstone (lower Eocene!. which is the producing formation in Mile Six. occurs at an average depth of 2,200 ft in the pool and dips north and east at from 15' to 20". The pool covers an area of approximately 350 acres. Mile Six is downfaulted about 600 ft from Section Sixteen pool to the soutb. and a major fault forms its western boundarv. The north and east boundaries are formed by the intersection of the sand top with the water-oil contact which occurs at approximately 2.440 ft subsea. An original gas-oil contact probably existed at about 1.875 ft subsea. Fig. 1 presents the latest structural interpretation of the pool. and Fig. 2 is an isopach map showing thickness of the total Parinas formation above the original water-oil contact. The heavy lints of Fig. 1 are contours on the sand top, and the fine lines are contours on the fault planes. This type of straight-line structural map was developed 1)) International's geologists to reflect structural conditions where the bedding planes dip and have no curvature. 'The La Brea-Parinas Concession is highly faulted by normal fault.. The beds are flat wherever exposed. The Parinas formation is approximately 635 ft thick. and it is etimated that 62 percent II the formation is effective sand. The original oil zone was about 565 ft thick. Fig. 211 presents an electric log showing typical Parinas sand development ill Mile Six pool. The Parinas band in Mile Six i. a well-sorted. medium- to-coal-se-grained. cross-bedded sand with minor lenses of shale and small lenses and pockets of pebble conglomerate. The sand grains are subangular to rounded and consist chiefly of quartz with feldspars. biotite hornblende, and augite as accessory minerals. Because of faulting of the Parinas- formation to the east and north of the pool. there is probably l possibility of a significant, natural water drive in Mile six. The faults within the pool. as indicated in Figs. 1 and 2. are of smaller disI,laceInent and seem to act only , partial barriers to fluid movement within the reservoir. RESERVOIR CHARACTERISTICS Core analysis data are available from five wells. The data were obtained from three wells (Nos. 3401. 3586 and 3719) at the time of their completion and from well 1996 when the original liner was sidetracked and the well was deepened ill 1946. Data from well 2779 were obtained in 1943 from old cores taken when the well was deepened in 1934. From these core analyses. the average porosity was estimated to be 22.6 per cent. and the average permeability to dry ail. was estimated to be 780 and Measured productility indices varied from 3.1 to 71.4 B/D per psi differential. Specific productivity indices varied approximately from 0.1 to 0.3 B./D per psi per ft of sand.

Jan 1, 1953

Discussion of the paper of EDGAR L. NEWHOUSE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin: No. 92, August, 1914, pp. 1801 to. 1806. G. C. RIDDELL, East Helena, Mont.-As nearly as I can recall at the present moment, there are only four or five large plants on the continent where the lead on charge is carried in the neighborhood of 40 per cent. These are at Herculaneum, Collinsville, and Federal, Ill.; Trail, B.. C.; and East Helena, Mont. Our object at the latter point is to smelt a maximum amount of Coeur d'Alêne lead sulphides in as compact and self-fluxing a charge as possible, and to this end we are now smelting a mixture that at times carries up to 42 per cent. lead. The monotony of producing the 7,000 tons of bullion shipped each month to. the Omaha and Chicago refineries is relieved somewhat by the fact that the 15,000 tons monthly of Coeur d'Alêne ores that are com-ing to us carry enough zinc to provide the one-half slag used with from 6.5 to 7.5 per cent. zinc clay after day. During the month of March, 1914, three lead furnaces in continous operation, each 136 in. long, averaged 249 tons per furnace clay, exclusive of coke and slag shells, which is smelting at the rate of 5.5 tons per square foot of tuyère area. The

Jan 11, 1914

Bernard MacDonald, Guanajuato, Mexico (communication to the Secretary*):—Mr. Iceyes's paper is very interesting to me because of my personal experience with the development of the ore-deposits of Lake Valley.

Jan 1, 1909

J. S. UNGER, ? Pittsburgh, Pa. (written discussion ?).-Firebricks intended for, the same purpose, but supplied by different manufacturers, may be of entirely different clays, contain different proportions of flint, calcined and plastic clays; the particles may vary widely in size; the water used to make the brick will vary; the pressure in molding will vary, depend-ing on whether the brick is hand made or power pressed; and the degree of burning in the same kiln will differ. These variables affect the melting point and the strength of the brick when heated. An important property, of a firebrick is its ability to resist heat and, at the same time, weight or load without serious deformation. The soft-ening point and the melting point of a firebrick may be several hundred degrees apart, and two bricks may show considerable difference in their softening points, but the melting points may be approximately the same. Bricks are not usually employed at temperatures close to their melting points. If they must withstand very high temperatures, the firebrick is discarded and a brick of more refractory material is used. Under these conditions' it is doubtful whether the determination of the melting point of a brick has much practical value. If the determination of the melting point is necessary, the test should he made on a portion of the original brick and not on a specially prepared sample. A small triangular pyramid with a base about 1 1/2 in. and 3 in. high can be sawed from the corner of the brick with a thin-bladed car-borundum wheel, without injuring or destroying the size of particles, the bond, or degree of burning of the original brick. This specimen can then he compared with standard Seger cones or tested by any other method desired.

Jan 12, 1919

By Leo Wolrnan

IN the relations that exist between capital and labor in this country, there is a bright as well as a dark side. After many years of distressing conditions of labor and a plentiful supply of propaganda, it is doubtful that the doctrine of the class struggle, however defined and stated, has been embraced by any influential and numerous elements of our population. Extreme and uncivilized methods of conflict, whether they be the labor spy as used by the employer or the sit-down strike by organized, labor, have come to be abandoned as the result of the pressure of sober and distinterested public opinion. Unwise terms of our law of trade unions and the unbridled zeal of its administrators show some slight signs of being revised in the light of 'experience and the protests of the law's own beneficiaries. At the point where labor policy touches economic conditions, the two powerful factions in the American labor movement appear to look with a less friendly eye on the bewildering succession of economic experiments and to have a deep nostalgia for a simpler and more prosperous economy.

Jan 1, 1938

By Robert I. Jaffee, Bruce W. Gonser

RECENT work by the authors1 established the constitutional diagram of the gold-germanium system. Of particular interest in the simple euctectiferous system was the eutectic alloy at 12 per cent Ge, which melted at the very low temperature of 356°C. and had an unusually fine eutectic structure. It was of interest to investigate the effect of third components on the melting point, microstructure, and strength of this alloy, and in this work the effect of copper is discussed rather completely, with less complete data on the effects of silver, platinum, nickel, and zinc. No reference in the literature has been found on ternary systems with gold-germanium. MATERIALS AND ALLOYING As in the work on the binary system, gold-germanium, the germanium used in this investigation was the cyanide-reduced, 99.9 per cent product, produced by the Eagle-Picher Co. Fine gold sheet from Handy and Harmon, pure platinum sheet from the American Platinum Works, copper magnet wire from Anaconda, nickel wire assaying 99.6 per cent Ni, and electrolytic zinc were used for alloying. To make the alloys, charges of the pure metals were put in a graphite crucible and melted in an atmosphere of pure hydrogen. The temperature was brought up to about 1050°C., and the metal allowed to freeze in the crucible. Except with alloys containing zinc, melting losses were consistently less than a few milligrams. When zinc was a component, weight losses up to half the weight of the zinc present were incurred, and the alloy compositions were calculated by assuming the entire weight loss to be that of zinc. In all other cases the composition of the alloys could safely be taken as that of the charge. The ingots, as solidified, were segregated, the heavier primary phases being at the bottom and sides of the ingots and the lighter primary phases at the top, but by sectioning the entire ingot vertically for microscopic examination, this factor could be evaluated. Ingots for microscopic examination weighed one gram, and those for thermal analysis weighed three grams. THERMAL ANALYSIS In this work, the eutectic line composition and thermal arrests were desired, and, after microscopic exploration had established the position of the eutectic line at a given percentage of the third component, a thermal analysis was run at that composition. The method of thermal analysis used in the work on the binary Au-Ge system,1 a method particularly well suited for a small quantity of material, was used in this work. Clearly defined arrests were obtained, although with some alloys containing platinum

Jan 1, 1946

By AIME AIME

AT FOUR O'CLOCK members gathered in the auditorium for the annual business meeting of the Institute which, according to its charter, must be held on the third Tuesday of February each year. President Turner presided and after the usual formal action on minutes announced that he would create a precedent by transferring the President's annual address (which by tradition has always been delivered at the banquet on Wednesday evening) to the business meeting, and, furthermore, would only present a brief abstract of it. Since it appears in full on pages 127-131 of this issue it can be followed with the careful attention its thoughtful analysis of current conditions deserves.

Jan 1, 1933

By B. G. Klugh

(New York Meeting, February, 1912). IN a paper before the Institute at Wilkes-Barre, Pa., June 1911,1 Mr. James Gayley discussed the application of this process to iron-bearing materials. The same author2 described the results of operations at the plant at Birdsboro, Pa. The purpose of the present paper is to present further discussion of some technical details involved in the operation of this plant, and of the theoretical and practical relations of this product to blast-furnace practice. Since Oct. 1, 1911, the Birdsboro plant has been in operation at the blast-furnace of the E. & G. Brooke Iron Co. The results have been highly satisfactory, although the material treated, being chiefly the flue-dust currently made by the furnace or taken from the accumulated stock-pile, was excessively high, and yet not uniform, in carbon, so that the desirable control or regularity of the amount of fuel in the mixture treated could not be maintained. Nothing could more forcibly demonstrate the flexibility of the process than the fact that, under these conditions, the sinter produced was, in all cases, of excellent quality. The Dwight & Lloyd process, as such, and its present highly-developed mechanical appliances were described by Mr. Gayley in the paper above mentioned. While the repetition of some particulars will be unavoidable in this paper, it will be confined to features bearing upon the metallurgical principles involved. According to the principle of the process, the finely-divided iron-bearing material to be sintered is intimately mixed with

May 1, 1912

By D. Harrington

ANNUAL or necessary inspections and investigations of coal mines for various purposes were made possible through the Federal Coal Mine Inspection Act of May 7, 1941, which authorized entry to the Secretary of the Interior through the Bureau of Mines. Primary object of these inspections is to obtain information pertaining to health and safety conditions. Among the purposes for which the data are to be used, are annual reports to Congress, the publication of inspection reports, and the compilation and publication of statistics. The act states that inspections and investigations shall be made by employees of the Bureau of Mines, who shall co-operate with other bureaus of the U. S. Department of the Interior, as well as with the official mine-inspection, safety cr health agencies of the several states and territories. The act specifies that a coal-mine inspector shall have "the basic qualifica-

Jan 1, 1946

By Sherwin F. Kelly

SINCE we used Chief Buehler's name last year to give our annual report a semblance of respectability, we can follow the good precedent thus established by telling of the work his Missouri State organization has been carrying on, as reported by H. S. McQueen. Considerable value is set upon their magrletorneter working which has covered over 13,000 sq. mi.), for the indications it gives of the major structural features of the region. Numerous geological problems have been tackled Ly resistivity techniques, among which are the locating and outlining of filled sink deposits of sulphides, of iron ore, and of fire clay; tracing of faults and solution channels; mapping of the preglacial structural pattern; measurement of depth of overburden; and

Jan 1, 1937

By E. H. Griswold, C. E. Beecher

DURING 1931 the petroleum industry has faced the most hazardous periods of its existence, caused by large potentials, overproduction, and demoralized markets. Two state governors actually resorted to the use of the militia in an effort to restore a semi-stabilized condition within the industry, to prevent waste of the states' natural resources, and to restore prices to a level that would yield the states a reasonable tax revenue. These conditions have made it necessary to put into effect most. stringent economies and have produced a spirit of cooperation between companies to an extent that never before existed. The necessity for unified action on such matters as proration and the advantages to be gained by unit operation are being realized by the oil industry as a whole. Fewer wells have been drilled and wildcat operations almost eliminated: development and operation costs have been greatly reduced and more attention is being paid to efficient recovery methods. The net work of oil pipe- lines has grown rapidly especially in the area of East Texas. The construction and operation of natural gas and gasoline pipelines into areas far distant from the source of supply has been one of the outstanding accomplishments. Refining efficiency has continued to increase and the public is being supplied with a better grade of gasoline at a lower price. The unreasonable tax which state politicians have succeeded in placing on gasoline has encouraged tax evasion and unfair competition by un- scrupulous dealers and has misled the public as to the true price of gasoline.

Jan 1, 1932

By H. P. Greenwald

THE Committee on Rock-Dusting was formed after the fall meeting of the Coal Division in Chicago in 1938. Its primary task was to study the recommended American practice for rock- dusting coal mines to prevent coal-dust explosions as approved by the American Engineering Standards Committee. After approximately two years' work he committee concluded that although certain portions of the recommended practice could well be revised, information needed for a logical revision was not at hand, and it was inadvisable, therefore, to make revisions

Jan 1, 1943

By C. M. Young

The safety lamp is the most common and convenient apparatus for detecting inflammable gases in mines, the presence of gas being shown by a blue flame, called the cap, if the wick has been lowered to suppress the luminous flame. The height of the cap increases with the proportion of gas and with the temperature of the lamp flame. Lamps of the Wolf type, the fuel of which is benzine, have a hotter flame than lamps in which vegetable oils are used, such as the Davy, and the Clanny, and are more sensitive than the latter and their many modifications. The Piehler alcohol lamp gives a still higher cap while the Clowes hydrogen lamp is most sensitive of all. While the effect of the temperature of the source of ignition is well known, the writer knows of no previous attempt to correlate the change of this temperature with change of the height of the cap produced, In order to determine the height of the cap at various temperatures, it was necessary to have a source of ignition the temperature of which could be accurately controlled over a considerable range. This condition was met by a coil of wire of high fusing point heated by an electric current controlled by a variable resistance. The use of a coil offered the further advantage of freedom from complications due to the flame of a burning fuel. Such a flame, being itself of variable height, would to some extent raise or lower the elevation of the base of the cap and therefore add to the difficulty of determining the height of the cap. Besides this, the presence of a small cap from the lamp fuel, commonly known as the "fuel cap," would interfere with the observation of small gas caps. After some experiment, a coil was made of platinum wire, No. 26, diameter 0.016 in. The coil was 17/64 in. (6.746 mm.) in outside diameter and had eight full turns in a length of 1/2 in. (12.69 mm.). This was connected to an electric circuit through an adjustable resistance, as shown in Fig. 1. In order to measure the temperature, a thermocouple was inserted in the center of the coil; the leads passed out at the ends and were ccnducted to a millivoltmeter. It is probable that the current of air passing upward through the coil resulted in the indication of a tempera-

Jan 1, 1920