Search Documents

By John D. Bardill

A cooperative project between the Bureau of Mines, Department of the Interior, and the Montana School of Mines, investigating results of hydraulic systems for transporting sand slurries for emplacement, was begun in August 1955. In such circumstances, the Bureau provides funds for a fellowship leading to a Master of Science degree as well as available instruments, tools, supplies and equipment. The School provides the ore-beneficiating laboratory with its equipment for use as a pilot plant. The success of a hydraulic backfilling method employing mill tailings depends largely upon the physical characteristics of the tailings. One of these characteristics is size distribution, especially in the finer size ranges. When being emplaced underground, almost impervious layers of slimes separate from some types of mill tailings containing a high percentage of slimes and settle on the top of the sand fill. These coatings may be so dense that the water in the slurry cannot percolate through them for proper drainage. Successive layers of fill in a stope, each with an impervious coating on top, sometimes build up a hydrostatic head, creating pressure on the bulkheads. This may cause breaks in the lining material, inducing sand runs and flooding the level and sumps below. Deleterious slimes flocculated and disseminated throughout the sands should help prevent the formation of impervious slime layers, increasing percolation and settling rates.

Jan 1, 1960

By W. W. Adams

Coal mining in the United States established a good safety record in 1939. The death and injury rates per man-hour of exposure to risk were favorable compared with most previous years, and the number of persons killed or injured in proportion to the quantity of coal mined was also lower than in any other year for which figures are available. Moreover, productivity per man-hour was higher than ever before. The number of man-hours of work performed increased 9 percent over 1938, but there was a slight decrease in the number of men employed. Reports from operating companies showed 539,375 men employed during the year, and the period of operation averaged 179 workdays per man. Man-hours of work numbered more than 678 million. Accidents to the workers resulted in 1,078 fatalities and 54,015 nonfatal disabling injuries, causing disability of the employee for more than the remainder of the clay on which the accident occurred. For each million man-hours of exposure of the employees to mining hazards the fatality rate was 1.59 compared with 1.78 for 1938, and the injury rate was 79.65 compared with 82.61 for 1938. Production of coal averaged 0.661 ton per man-hour compared with 0.637 ton in 1938. The weighted average length of the workday was 7.03 hours or virtually the same as the previous year's average of 7.04 hours. Measured in man-hours, the average period of employment per man was 1,257 hours in 1939 and 1,147 hours in 1938.

Jan 1, 1942

By R. Pelton, Z. Dai, S. Yang

ABSTRACT Hydrophobic polystyrene nanoparticles were evaluated as potential flotation collectors for pentlandite. The flotation of hydrophilic glass beads demonstrated the nanoparticles’ ability to induce flotation. Deposition of nanoparticles on glass surfaces increased the contact angle and enhanced adhesion of the beads to air bubbles. High flotation recoveries were achieved when 5–10% of the bead surfaces were covered with nanoparticles. Surface functionalization—the addition of vinylimidazole to polystyrene nanoparticle surfaces—caused the nanoparticles to selectively deposit onto pentlandite surfaces in the presence of Mg-Si slimes. Ongoing work includes attempts to identify specific applications where nanoparticle collectors might be cost effective. _ KEYWORDS Flotation, Nanoparticle collector, Coverage

Jan 1, 2014

By James D. Bliss

Sedimentary deposits of pluvial Lake Bonneville are an important source of sand and gravel suitable for aggregate and construction in Utah. Data on Lake Bonneville basin sand and gravel deposit thickness, volume, grain size, percent of fines, and durability were statistically analyzed to detect variations associated with geologic domains, geographic location, Lake Bonneville shorelines, and sand and gravel deposit type, and to construct quantitative deposit models. Analysis showed several trends; (1) sand and gravel in younger shorelines was slightly more durable and the deposits considerably larger in volume, (2) younger shore- lines are also more likely to contain more than one genetic deposit type, (3) the volume of terrace deposits is larger than beach deposits, (4) terraces and beaches are generally thicker than spits and bars, (5) the northern part of the Bonneville Basin contains slightly more durable sand and gravel than the southern part of the basin and is more likely to contain deposits composed of more than one genetic deposit type, aid (6) the Wasatch domain deposits are composed of more than one genetic deposit type more often than deposits of the Basin and Range domain. Three additional conclusions with immediate economic significance are; (1) the median sand and gravel deposit in the Wasatch domain, 360,000 m3 (275,000 yd3), is three times larger than that of the Basin and Range domain (120,000 m3 [90,000 yd3]), (2) the median deposit thickness in the Wasatch domain, 5.8 m (19.0 ft), is nearly twice that of the Basin and Range domain (3 m [lo ft]), and (3) the Wasatch domain also contains slightly larger diameter gravel. These three conclusions are significant because the trend for sand and gravel development in the Bonneville Basin is to move from the Wasatch domain to the Basin and Range domain. Smaller, thinner deposits with smaller diameter gravel will require more surface area to mine than would have been necessary in the Wasatch domain. The result is a higher cost for sand and gravel in construction projects in the Salt Lake City area, especially since the gravel must also be hauled farther.

Jan 1, 2001

O. S. GARRETSON, Buffalo, N. Y.: If I may judge from the half-tone illustration engraved from a photograph of this medal and accompanying Dr. Prazer's paper, I do not think the cast ing is exceptionally fine. I have often made castings of simi lar character which I think were equally good. For instance, I have taken a coin, moulded it directly in fine sand, and cast from it in Scotch (or the equally good, if not better, Ameri can Scotch ") foundry-iron a copy quite as sharp and smooth as the original. The secret is in using very fine sifted sand. In fact, I have used for this purpose the dust which had accumulated on the beams overhead in my foundry, riddling it with a very fine sieve before using it. ['NOTE BY THE SECRETARY.—After the session at which these remarks were made by him, Mr. Garretson cast at his Buffalo foundry, in the presence of a number of members of the Institute, copies of the bronze pin furnished to visiting members by the Local Committee of the Buffalo meeting. The accom panying illustration, Fig. I, has been reproduced from a photograph of such a casting, made in green sand, under the conditions of ordinary foundry-practice, and not subsequently polished in any .way. I can also certify that the photo graphic negative was not touched, to improve its clearness of definition, before the production of the " half-tone" plate from which Fig. 1 has been printed. As, in the case of the Kytchtym medal, it was the thin, ribbon-like sprue, rather than the low-relief features of the medal itself, which indicated the fluidity of the metal and the sharpness of the casting, so in this work of Mr. Garretson it is the long and slender pin which offers the strongest evidence of these qualities. It is scarcely neccssary to point out that the filling in the mould of a long and nar row opening, such as this pin presents, is the severest test that could be imposed upon the casting, and that the sharpness of the point of the pin in the casting is striking evidence of the success with which this test has been met. The Pittsburgh Testing Laboratory .has made for the American Manufacturer measurements of this casting and an analysis of the sprue. The thickness of the main casting is from 0.049 to 0.068 inch. That of the tag bearing the stamped number is 0.024 inch. The analysis, which represents the iron ordinarily employed by Mr. Garretson for thin castings, is as follows :

Jan 1, 1899

By E. G. Kearnery

Introduction It is believed that the present paper will be of some interest, not because of any outstanding features of Renabie milling practice but because Renabie is the first gold mining property in a newly explored area - in Leeson and Rennie townships, Sudbury district, Ontario - to reach the production stage. The Renabie mill was originally designed by the General Engineering Company (Canada), Limited, as a 300-ton plant and went into operation in June, 1947, treating an average of only 128 tons a day for the balance of that year. Toward the end of 1948 the capacity of the plant was expanded to 450 tons a day, and the tonnage treated was gradually increased from the 1947 figure to the point where 420 tons a day was averaged for the first nine months of 1949. Description of Ore In general, the outstanding gangue component of Renabie ore is white quartz, which comprises at least 80 per cent of its total bulk and in some sections considerably more. Virtually all the gold occurs in very finely divided state; only very rarely has free gold coarser than 325 mesh been observed. The ore has a very low sulphide content, ranging from about 0.50 to 1.00 per cent by weight. The gold occurs both free in the gangue and ? locked in sulphides, the proportion of one to the other varying considerably from one orebody to the other. Pyrite is by far the most abundant sulphide, followed by galena, which, however, appears to be entirely absent in some of the orebodies. Minor amounts of pyrrhotite, chalcopyrite, chalcocite, and sphalerite have been noted. The ore appears to be entirely free, or almost so, of minerals containing arsenic, antimony, or molybdenum, and in general it could be described as free milling. The various hindrances to extraction of the gold which have been met with are believed to be due largely to the very finely divided state of the metal and to its intimate association with the sulphides and gangue. The ore contains silver, with the gold-silver ratio about 3:1.

Jan 1, 1950

By R. Stauffer, S. Lindsay

"Sherritt Gordon Mines Limited utilizes pressure hydro-metallurgical techniques to recover nickel, copper and cobalt from su1phidic concentrates, mattes and various other metal-bearing materials.A brief description of the nickel refinery operation is given. In the nickel refinery process, an ammonia pressure leach is employed to treat the feed materials to dissolve the non-ferrous metals as their respective ammine complexes. The resulting leach solution goes through a series of steps which removes copper as copper sulphide and further purifies the solution prior to nickel precipitation by hydrogen reduction. The reduction end solution, containing the cobalt which was originally present in the leach solution as well as residual nickel, is treated with hydrogen sulphide. The resulting nickel-cobalt sulphide precipitate feeds the soluble cobaltic ammine process, which separates the nickel and cobalt and recovers the cobalt as a pure powder.A detailed description of the cobalt recovery process is given. Included are the various steps, comprising: acid leaching of the mixed sulphides, solution purification, ammine complex formation and cobaltous oxidation, two-stage nickel precipitation, cobalt conversion and reduction. A brief description of cobalt powder handling is included, along with typical physical properties and chemical analyses of the cobalt product. In general, the purpose of this paper is to describe the present plant practices employed in the recovery of cobalt as a by-product of the nickel refinery operations."

Jan 1, 1967

R. W. Raymond, New York, N. Y,:—Since the presentation of my note on this subject at the New York Meeting, Professor Louis has pointed out an error in my statement of his conception of " pitch "—namely, he understands the pitch, in the restricted sense which he proposes, to be the angle of inclination of the axis of an ore-body, measured on the vertical plane drawn through the body; whereas, I represented him as proposing to define " pitch " as the angle of inclination of an oblique body, measured on the plane of the dip, in the direction of the strike. The difference will appear upon consideration of the accompanying isometric projection, Fig. 1, in which ABCD represents the plane of the inclosing ore-deposit (vein or bed), and AC the axis of the oblique ore-shoot. ABE is the angle of the dip, as universally understood; and ACE

Jan 1, 1909

By Richard E. Thill

Engineering properties of rock are essential in most phases of mining from site reconnaissance through mineral processing. Review of the literature indicates, however, that property data is scarce for most coal measure rocks in the United States. The Bureau of Mines, U.S. Department of the Interior, has undertaken a wide-ranging testing program to provide more complete property data for coal strata in the U.S. coal basins. The property data are expected to have application in geophysical exploration, the development of pre- mining and hazard detection probes and instrumentation, mine design, engineering and rock mass classification, subsidence engineering, and ground control. This paper describes the comprehensive program encompassing in situ geological, geophysical, and geotechnical properties and laboratory determinations of acoustic, electromagnetic, physical, mechanical, and index properties and discusses results for 500 ft of coal measures at a minesite in the Northern Appalachian, Eastern Coal Province.

Jan 1, 1982

By Frederic P. Dewey

The Bureau of the Mint of the United States Treasury maintains 13 ofEces for the purchase of gold-bullion, and this paper describes an investigation to establish the reasonable differences in the assay-results at the various institutions which may be commercially allowable in the settlements between them. Beginning with the comparative assay of proof-gold at the Philadelphia mint and the Utrecht mint, which shows 0.00002 as the closest agreement now possible, nine tables of comparative results, taken from the regular work of the service, are given..These tables begin with very fine gold, produced in an electrolytic refinery, showing close agreement in the assay-results, and follow through decreasing gold fineness and increasing amounts and complexity of base metals to very impure and complex bars produced at cyanide-mills, some of which give widely-varying results. Next is given a series of results on samples, prepared and sent out to various laboratories in the service, to test the influence of different metals and various combinations upon the agreement of the assay-results ; 11 samples were sent out and each one was assayed from 44 to 71 times, making a total of 623 assays. To these ire added 107 assays of identical samples of coin-gold. On a previous occasion,' I have endeavored to show the degree of accuracy that may be expected in the ordinary everyday analysis of various materials, and on another occasion,2

Jan 1, 1910

By William G. Schultz

Sylvite of Canada, a wholly owned subsidiary of Hudson Bay Mining and Smelting Co., operates an 8000 TPD potash mine and refinery located nine miles North East of Rocanville, Saskatchewan. Prior to Hudson Bay's entry in 1968 into potash mining and refining, it was one of the more traditional and conservative Canadian Mining Companies whose principal business had been for many years a successful copper-zinc mining and smelting operation located at Flin Flon, Manitoba. The potash reserves being mined by Sylvite were acquired through the acquisition of Francana Oil and Gas. This acquisition was at the time when several major potash mines were being developed or had recently been brought into production in the Province. These mines are owned by either very substantial Canadian Mining Companies or Multi-National Mining Companies with considerable potash mining experience. At that time, it became very apparent because of the new mines coming into production, potash mining and refining would quickly become a very competitive industry. Because of long term considerations, Hudson Bay decided to proceed with the development of its potash reserves, recognizing the Mine and Refinery would have to be the most advanced available in order to successfully operate. This report deals with the mining operation at Sylvite and the degree of success Sylvite has achieved.

Jan 1, 1972

By Robert F. Shurtz

This paper suggests that pre-occupation with the random process model notised by geostatisticians may result in neglect of more promising techniques, especially since the random process model does not appear to be essential to current geostatistical procedures. This point of view is emphasized pictorially. To emphasize the potential of new techniques a simple application of the conventional Brownian function is described. The probabilities estimated in this truly random way are different from those estimated by Kriging

Jan 1, 1980

Jan 1, 1991

By Walter Nuñez

La finalización de la estimación de reservas de un modelo de mina cuestiona la asertividad del modelo de Mina para la planeación minera. En ese sentido, el presente texto señala la Reconciliación como la comparación real histórica de tonelaje, leyes y contenido fino estimado, entre el modelo de mina y planta concentradora. La reconciliación permite conocer y ajustar mediante el uso de factores, la planeación mensual y anual de los siguientes años de la operación minera, y así cumplir con los compromisos mensuales asumidos de envío de contenido fino desde mina. Así también se muestra el proceso que sigue la explotación minera a tajo abierto en Toquepala, las variables que influyen en la variación de la reconciliación y algunas pautas a considerar para minimizar estos errores de reconciliación entre mina y concentradora.

Sep 19, 2006

By J. B. Gayle

In a modern blast furnace, production depends, to a large extent, on the rate at which the furnace gases can be forced through the charge. Since these gases must make their way through the voids between particles of coke, ore, and limestone, the size and size distribution of the stock-column materials are of considerable importance. Also, because the coke pieces support the weight of the overburden and provide the majority of the voids through which the gases pass, their ability to withstand the shattering and abrading forces to which they are subjected should be related to the maximum obtainable production for any particular furnace. Although the wide acceptance of this point of view is indicated by the ever-increasing demand for stronger and more uniform blast-furnace cokes, economic considerations demand that a quantitative evaluation of the relation between coke quality and blast-furnace performance be made available to the industry at the earliest possible date. The following studies of size-distribution patterns and breakage processes were, therefore, conducted as a part of a preliminary investigation intended as a basis for future studies of the relation between coke quality and blast-furnace performance. The major findings may be summarized as follows: 1. New evidence for the presence of two independent distributions of sizes in run-of-oven cokes has been obtained, and a method for characterizing and estimating the relative importance of the individual distributions has been demonstrated. This method has also been used to study the different types of degradation taking place during the tumbler test.

Jan 1, 1954

By Matheus Teixeira Fraga

É comum o uso de modelos matemáticos no intuito de prever a qualidade do coque, sendo a maioria dos modelos atualmente disponíveis baseada nas propriedades dos carvões. Para este trabalho foram feitas misturas binárias e ternárias de carvões com variados teores de matéria volátil, a fim de se produzir coque em escala laboratorial. A reatividade ao CO2 em termobalança e resistência mecânica em tambores foi avaliada. Dois modelos para previsão de indicadores de qualidade do coque foram avaliados, o modelo aditivo e o modelo de interação. A partir da metodologia desenvolvida em laboratório foi possível produzir, avaliar e comparar coques feitos a partir de diferentes carvões e misturas. O modelo aditivo mostrou uma boa capacidade de prever a reatividade dos coques. No entanto, para os índices derivados dos testes de tambores os valores calculados mostram uma diferença importante em relação aos experimentais, indicando interação dos carvões no processo de carbonização. Nos resultados do modelo de interações, os valores calculados para reatividade e resistência mecânica, se comparados com os resultados do modelo aditivo, mostraram uma melhora na capacidade de previsão da qualidade do coque. O modelo de interações se apresenta como uma ferramenta interessante na seleção e mistura de carvões.

Aug 17, 2017

By Loughnan FC

There are some thirteen laboratories in Australia in which coal petrological work is carried out on a consistent and routine basis. Applied coal petrological research is conducted by several institutions in different disciplines which can be grouped into four main categories:

Jan 1, 1989

By S. James Campbell

Ladies and Gentlemen: Never in the history of our mining industry has the emphasis on public relations been accelerated as much as it has in the last few years. Knowing of your keen interest in this subject I consider it a great privilege that your program committee has asked me here to discuss the crushed stone segment of our industry approach to this important part of our daily business lives. As you are aware, crushed stone operations are present in almost every segment of the country wherever aggregates for construction projects are required. The tonnage of crushed stone produced is second only to sand and gravel - another source of aggregates - and this together with sand and gravel amounts to over half of the tonnage of all mined products in the United States. What is unique about this industry that will be of interest to all of you in analyzing how they have approached Public Relations? The fact that it is so wide-spread is of course obvious, but perhaps a more significant nature of this segment of the mining industry that has brought it more in the limelight of public interest and on a larger scale is the location of a large part of the quarries quite close into the urban area and population centers where you have the greatest demand for aggregate products.

Jan 1, 1969

By J. J. Forbes

The original organic act establishing the Federal Bureau of Mines in 1910 and the amended act of 1913 indicated that promotion of the health and safety of mine workers was to be ore of the chief functions4/ of the Bureau. Many of the field and laboratory studies pursued by the Bureau are designed to improve conditions under dish minors must work. As the Bureau has no legal authority to enforce safety rules, it must rely upon cooperation of employer, employees, State mining or other departments, and labor organizations for success in promulgating its finding and making recommendations. The staff of the Safety Division, which is essentially a service organization of the Bureau, is composed of 28 safety instructors, 29 engineers, 18 clersk, and 7 others engaged in promotion of an educational program in an effort to improve conditions in the mining industry. The work is directed from 14 safety stations in the United States and 1 in Alaska. The work of the personnel, of the mine safety car that operates in. the anthracite region of Pennsylvania was supervised and directed by the district engineer in charge of the Wilkes-Barre (Pa.) Safety Station.

Jan 1, 1940

By John B. Ivey

This is a geologic study of the U.S. Bureau of Mines Oil Shale Tract in the Piceance Creek Basin of Rio Blanco County, Colorado for the preparation of a set of detailed surface geologic maps, measurement and identification of joint attitudes and frequencies, and the classification and mapping of the soils of the area.

Jan 1, 1978