Search Documents

The merging of flash smelting with spray converting in one single furnace is proposed as a continuous copper making process. The proposed process is expected to produce blister copper, clean slag and gas with high sulfur dioxide concentration. Some high grade matte is an intermediate product recycled within the proposed furnace, spray-atomized and converted. The thermodynamic equilibria of the simultaneous oxidations which take place during copper smelting and converting are discussed in order to establish the gradient of oxygen potential along the furnace required for smooth operation. The proposed process is a dynamic system designed to reach equilibrium only close to the slag skimming end of the furnace. The process feasibility is based on the predesigned significant difference between the rates of converting reactions in a finely dispersed system and the rates of deconverting reactions between immiscible liquid phases of restricted interface area. The converting of small stationary droplets of matte, in a silica saturated system, was studied in the laboratory for extremely short oxidation times (10 to 120 seconds). These experiments led to some interesting observations on reaction mechanisms and kinetic trends. The droplet size and the matte grade affected very strongly the oxidation rate and the proportion of the different products obtained.

Jan 1, 1976

By Florian Kongoli

The optimal operation of the blast furnace depends considerably on the properties of the sinter fed into the furnace. As a result, the optimization of the sintering processes has a direct effect on the overall effectiveness of the iron making processes. In order to produce a good sinter special care needs to be taken in order to assure it has a good permeability and reducibility and it is able to retain these properties for a certain time. If the sinter starts to melt down early in the upper part of the blast furnace, where its solid state reduction is essential, permeability decreases, the gas channels get blocked, reductibility diminishes and serious problems may also follow. Among the factors that influences the above mentioned sinter properties are the oxygen potential and fluxing components. Nevertheless, their effect on the phase relations during sintering and sinter reduction conditions has not yet entirely clarified and confusion exists in literature. This quantification becomes even more important today where many new minor components such as Al2O3 and MgO enter the sinter through raw materials. This work quantifies the effect of oxygen potential and fluxing components such as alumina and magnesia on the liquidus and phase relations of the sinter primary melts in the iron rich portion of CaO-FeO-Fe2O3-SiO2 system at sintering conditions. This is carried out by the means of new type of industrial diagrams in the form of Fe/CaO vs. SiO2 that can directly help the optimization of the sintering processes.

Jan 1, 2006

By A. J. Paul

Traditionally, 16"/50 caliber projectile shells have been fabricated from forged steel. The Naval Surface Warfare Center (NAVSWC) has determined that cost savings of approximately 60% (-$4.7M/year) as well as improved shell fragmentation can be achieved by casting these shells from austempered ductile iron. One of the technical concerns arising out of this material substitution is the role of the casting process in controlling the quality of the cast shells. Optimizing the process through proper orientation of the mold, placement of chills, superheat, etc., can minimize shrinkage porosity and, consequently, flaw size. For this purpose, the mold filling and subsequent solidification of the projectiles was simulated using a 3-D, fully transient, coupled fluid flow and heat transfer model based on finite differences. Several casting orientations were investigated and the casting parameters were varied to optimize the process and minimize casting defects. A comprehensive software tool, which was developed using state-of- the-art visualization techniques, has been used to analyze the process of casting. Emphasis is placed on the use of this visualization tool as an aid to the foundry engineer for process optimization.

Jan 1, 1992

By Mitsuru Tanahashi

In order to develop an effective process for the production of a solar-grade silicon (SOG-Si) from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at 1773 K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten MG-Si followed by oxygen gas injection into the melt (Two-stage connecting process). II) II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

By Krzyszof Borowiec

With the aim of determining the thermodynamic conditions for sulfation of impurity elements, in particular magnesium, in titaniferous slags the equilibrium gas composition for the sulfation reaction: MO + so2 + 1/2 02 = MS04 has been studied by an EMF technique with a solid zro2 + Cao electrolyte. Here M denotes the impurity elements: Mg, Ca and Mn, and the following _oxide systems have been studied: Ti02-MgO-Fe2 o 3 , Ti02-MnO-Mn2 o 3 , and Ti02 -CaO-Si02 , all in the . temperature range 700-1000ºc. Reproducible EMF values were obtained by adding small amounts of -Na2so4 to the oxide-sulfate mixture. From the observed results the Gibbs energy of formation of the phases Mg 2Ti04 , MgTi03 , MgTi 2o 5 , MnTi03 , CaTi03 , and CaTiSio5 , as well as the activity of MgTi05 in the solid solution with Fe2Ti05 have been calculated. The results show that, from a thermodynamic viewpoint, sulfation of these impurities in titaniferous stags i:s favorable- at around and below 800ºC.

Jan 1, 1985

By D. M. Jones

In May 1999 the first campaign of the BHP San Manuel flash smelting furnace (FSF) will be concluded after having set world records for both campaign length and tonnage smelted for an Outokumpu copper flash smelting furnace. This paper reviews planned process and equipment modifications including: The installation of a new 36,000 mt concentrate storage facility; replacement of the existing dryer electrostatic precipitator with a baghouse; modification of the FSF dry charge bin and feed system to achieve mass flow and uniform feed to the concentrate burner; modifications to the FSF and its ancillary cooling systems; modifications to the waste heat boiler and offgas handling system to increase gas handling capacity and improve process efficiency;- and improvements to the FSF fugitive gas collection system. A brief review of the planning and execution of the scheduled 45 day shutdown is also given.

Jan 1, 1999

By Elizabeth M. Ho

Oxidants are added in uranium leaching in acid media to convert iron(II) in solution to iron(III). Iron(III) has an important role in the leaching of uranium by acting as an electron transfer agent for the oxidation of uranium(IV) to uranium(VI). The oxidation of iron(II) to iron(III) in sulfate solutions using sulfur dioxide/oxygen (SO2/O2) was carried out under typical uranium leaching conditions (pH 1-2, 20-50°C) to confirm literature trends and this work was then extended to the use of SO2/O2 in the leaching of uranium ore. The oxidation rate was found to be dependent on the initial SO2/O2 volumetric ratio and the oxygen mass transfer rate, but was independent of the initial iron(III) concentration above about 200 ppm at pH 2. The presence of 55 ppm organic extractant (Alamine 336) decreased the reaction rate. The oxygen mass transfer coefficient (kLa) for the mixing tank system was measured and was found to decrease with increasing solids density in a 1 g L-1 MgSO4.7H2O solution.

Jan 1, 2003

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

Acid mist generation is a major concern in zinc, copper and nickel electrowinning industries and there is a strong environmental drive to control its emission into the work environment. Foaming reagents are typically added to the electrolyte to alleviate this problem. In zinc electrowinning, Licorice and Saponin are examples of foaming reagents used for this purpose. In order for the foaming reagent to be effective, its foaming behavior must be determined. In this work, a test procedure was developed to study the foaming characteristics of various surfactants for use as foaming agents to control acid mist in aqueous metal electrowinning. This new test was termed as "mini-flotation test" and it was used to study the foaming behavior of a large number of reagents in an industrial zinc sulfate electrolyte under simulated zinc electrowinning conditions (gas sparging). In addition, the influence of important process parameters such as current density, electrolyte temperature, reagent addition level and sulfuric acid concentration on the foaming characteristics of the electrolyte for each surfactant were investigated. The results of this study have identified the most important factors that influence foam formation, growth and stability. This method could be used as a process control for reagent addition in the cellhouse by generating a calibration curve for the optimum electrolyte conditions.

Jan 1, 1997

By Girley Ferreira Rodrigues, Crocce Denise Romano Espinosa, Victor Bridi Telles, Eduardo Junca, Jorge Alberto Soares Tenorio

"Steel sector is responsible for the generation of solid waste, liquid and gaseous effluents. The Solid waste are mainly composed of slag, dust, sludge and scrap. The industry generates approximately 650kg of solid waste per tonne of steel. Approximately 10% of this waste is in the form of dust and mud. The basic oxygen furnace dust is a waste generate by steel sector. Each tonne of produced steel generates 10 to 20 kg dust. Thus, the aim of this paper is study the reduction of pellets made with BOF dust using hydrogen and study kinetic during the reduction. The tests were performed in a netzsch thermobalance to obtain the data of lost mass. This loss mass is coming from iron oxides present in the BOF dust.IntroductionThe generation of solid waste is a problem for many companies in the steel sector. The main solid wastes generated are slag, dust, sludge and scrap [1]. Beyond solid waste liquid and gaseous effluents are also generated.The basic oxygen furnace is responsible for 60% of all steel produced. This sector is the second largest generator of solid waste from an integrated steel mill, contributing with 27% of solid waste generated in a plant ( 5-7 million tons of waste generated annually worldwide) [2,3,4]."

Jan 1, 2013

By Robert D. Pehlke

"The evolution of oxygen steelmaking is reviewed and new operating processes are described. The developments which could impact this technology are summarized. Staged and continuous steelmaking are considered in the light of new technologies. The future opportunities for oxygen steelmaking processes are overviewed. IntroductionThe use of oxygen in steelmaking was originally brought on the scene by the development of pneumatic steelmaking. Sir Henry Bessemer in England originally conceptualized the use of gaseous oxygen in steelmaking, and then he and William Kelly in Eddyville, Kentucky independently developed the original pneumatic process which involved blowing air through a bath of molten pig iron to oxidize the carbon and silicon and produce steel. This process and many following processes, including those which would use pure oxygen gas, have been proposed.Beginning with the first commercial oxygen steelmaking vessels at Linz, Austria in 1952, the world steelmaking industry has adopted this style of processing. In general, the process has involved the use of steel scrap in amounts from 20 to 35% of the metallic charge with molten pig iron produced in blast furnaces making up the remainder. The impurities in the charge are oxidized through the use of oxygen gas injected into the steelmaking vessel.However, currently being adopted into commerical practice and on the horizon are a number of advances in this process which include the use of iron ores as a source of iron and oxygen, the use of an all scrap charge, incorporation of pre-reduced iron, the use of auxillary fuels to change the balance of cold and liquid iron-base charge materials and numerous refining techniques."

Jan 1, 1988

By Xiao Long, Ting Wu, Lilong Zhu, Qian Wang, Shengping He

"During the continuous casting of peritectic steel slabs, mould fluxes with high crystallization capacity are usually chosen for improving slab surface quality. However, the lubrication condition of casting shell also could be deteriorated. Since precipitation of crystals within liquid slag film can change the composition and property of liquid slag over solid-liquid slag film interface region, its impacts on continuous casting process also are not clear. In order to clear this phenomenon, an experiment method was put forward, and mould fluxes for peritectic steel slabs continuous casting were selected and examined. The results reveal that after crystals have been separated, the crystallization capacity of leftover liquid slag increased with different levels, which could deteriorate the lubrication condition of casting shell and cause a series of problems. Thereby, mould fluxes with high crystallization capacity at beginning for heat transfer control and then weaker after crystallization should be considered in the future.IntroductionIn the continuous casting of peritectic steel slabs, contradiction between heat transfer control and slab shell lubrication by mould fluxes has been treated as a key problem for maintaining a smooth manufacturing process [ 1]. Strong and uneven horizontal heat flux over the meniscus region will cause uneven solidification of casting shell, especially for peritectic steel slab with enormous volume change caused by phase transition. All of those could cause surface defects like longitudinal crack [2-4]."

Jan 1, 2013

By M. Potesser

After the primary or secondary lead production the bullion lead is remelted and charged into a vessel with following refining process. The removing of arsenic, antimony and tin takes place by salt slags or oxidizing gases like air or pure oxygen. Due to the increasing lead price, Messer Austria GmbH in cooperation with the institute of Nonferrous Metallurgy at the University of Leoben have developed a new process named OXIPOT for the refining of tin, arsenic and antimony. The OXIPOT process is in principle based on purging technology with a ceramic or steel purging device. This leads to an increased retention time of the refining products due to the deeper bath level and an optimized specific reaction volume concerning the bubble size. This paper describes the process, pilot plant, and thermodynamic calculations for the optimization concerning the selectivity of element removal.

Jan 1, 2008

By Tatsuro Ariyama, Michitaka Sato, Atsushi Sakai, Sumiyuki Kishimoto, Ryota Murai

"In order to achieve high pulverized coal injection operation in a blast furnace, optimization of the injection lance arrangement was carried out using an experimental furnace and mathematical models. To increase the injection rate of pulverized coal, it is required to raise the combustion efficiency of pulverized coal. It became clear that multi-point injection and the lance arrangement to avoid interference among the coal streams injected were so effective in increasing combustion efficiency. With these findings, the eccentric double lance arrangement has been newly developed.At NKK, Fukuyama No.4 Blast Furnace, after the improvement of the lance arrangement, the maximum injection rate reached up to 230 kg/thm and an average monthly record of 218 kg/thm was successfully achieved.IntroductionFrom the viewpoints of reducing the production cost of pig iron and prolonging coke oven life, high pulverized coal injection over 200 kglthm is actively pursued by ironmaking industries[1-2].Coal particles injected into the blast furnace are consumed by combustion in the raceway and also in-furnace reaction like solution-loss reaction (C + CO2 = 2CO). The amount of coal consumed by the latter process is determined by the carbon balance in the blast furnace and there is a limit. Therefore, to increase the injection rate, it is desirable to improve the combustion efficiency in the raceway. For these purposes, the optimization of the lance arrangement was examined by a hot model and mathematical models."

Jan 1, 1996

By William J. Mallio

Substantial differences between in situ and conventional technology require that in situ ore grade be established for deposit as distinct from the total contained metal value. Establishing an in situ ore grade involves determining the fraction' of the contained metal that can be leached by the fluid. This depends on the proportion of the ore minerals that occur on fluid flow paths as defined by the permeability distribution. Mechanisms involved in the in situ mining of sulfides are: oxidation of the sulfur, solution of the metals, complexing of the released metals, and a transport to a recovery point. Metal ions may be delayed or lost due to inefficiencies in these pro-cess steps or by reactions of the metal ions in solution with the rock. These reactions can involve precipitation of new phases, exchange of the metals of the interest with Ca or Na in clays or zeolites, retention of metals in oxidized mineral grains, or secondary enrichment of other sulfides along the paths of the solution flow. The efficiency of solution of metals and potential loss or delay mechanisms are controlled by local equilibria (the Eh, pH conditions) present in different parts of the ore zone. Permeability distribution in the rock mass and the coincidence of ore minerais with flow channels must be determined before a deposit can be judged suitable for in situ mining. Laboratory studies indicate that the natural permeability system is dependent on the degree of cementation of veins by late generation hydrothermal activities. The major conclusions of the study are:, 1. Deposit selection is critical; suitable deposit types include deep lying sedimentary deposits, selected zones of porphyry systems and vein controlled hydrothermal deposits; 2. Adequate laboratory and geochemical analyses should be undertaken through quantitative petrographic study and permeability mapping; and 3. Economic incentives for in situ mining must consider limitations of recovery caused by inefficiencies in dissolution and transport associated with particular deposits.

Jan 1, 1981

By L. Trincado

Mantoverde is a heap leach-SX-EW plant that was commissioned in December 1995 at a production rate of 42,130 ton of copper per year and 5.4 million ton of ore per year. Copper production has steadily been increased to 57,290 ton in 2002. Forecast copper production for 2003 is 60,000 ton for an ore treatment rate of 8.5 million ton. Several improvements in the heap leach process have been implemented. The main process improvements are related to the optimization of heap height, particle size, irrigation rate and leach cycle, in addition to a better heap drainage design and a solution management system. A first dump leach operation was started in 1999 at a production rate of 1,922 ton of copper. A second dump leach operation was started in early 2002 at a production rate of 2,805 ton of copper. Dump leach production will be increased over time to as much as 24,000 ton of copper. The main heap leach process improvements, as compared to the original plant design, as well as the main dump leach operating parameters are discussed in this paper.

Jan 1, 2003

By L. G. Wiseman

The raw materials processed, highlights of technology used, and products produced at INCO's Copper Cliff Nickel Refinery in Ontario, Canada, are described in this paper. INCO's Bessemer matte separation process yields various nickel and copper products and intermediates. The latter presents the main supply of raw materials for the Refinery. Key features in the Refinery are Top Blown Rotary Converters and the INCO Pressure Carbonyl (IPC) process. Process improvements made since the commissioning of the Refinery in 1973 are also discussed. The Refinery produces a variety of nickel products, including nickel powders. Residue after carbonylation presents an important intermediate enriched in precious metals and cobalt that serves as feed to downstream operations for recovery of the residue's metal values. Also discussed are detection, measurement and control procedures which ensure safe operation.

Jan 1, 1988

By W. L. Cornell

Bulk sulfide concentrate produced from Missouri Pb ore concentrator tailings must be reground to liberate sulfide values for subsequent sepa-ration. Studies to determine grinding parameters for optimum liberation were carried out using optical microscopy coupled with image analysis. The major sulfide phases present in the ground mineral particulates are marca-site, pyrite, sphalerite, galena, chalcopyrite, siegenite. and bravoite. Results showed that the base metal minerals were liberated by grinding to 74 micrometers (200 mesh), but the siegenite and bravoite required grinding to 20 micrometers or less to achieve liberation. Both the experimental method and results are presented.

Jan 1, 1987

By D. G. C. Robertson

The thermodynamics and kinetics of the reactions involved in fuming zinc from oxide slags using coal or coke were first studied in 1955 and have been the subject of many investigations since that time. The key reaction is ZnO(in slag) + CO Zn(g) + COl. This paper will review the some of the recent work, and will add new insights obtained in experiments carried out by the authors. In the first series of experiments it was shown that the reaction 2Fe2+ + ZnO = 2Fe3+ + Zn(g) or 2FeO + ZnO = Fe2O3 + Zn(g) does not occur at an appreciable rate, as is expected from thermodynamic considerations. In the second series of experiments it was shown that zinc does not fume from the slag at a significant rate unless a reductant has been added. This again is in accord with thermodynamic considerations, but is in contradiction to some of the experimental results reported in the literature. A third series of experiments was carried out with excess coke being present, so that the rate of supply of reductant was not in any way controlling the rate. The kinetics of zinc oxide reaction were then found to be independent of the zinc oxide concentration, but increased with increasing basicity, and temperature. The presence of high concentrations of FeO in the slag also improves the kinetics. At low zinc oxide concentrations iron oxide reduction occurred in parallel with zinc oxide reduction. We propose that (under the conditions of this work) the kinetics were controlled by a chemical step, namely the rate of desorption of an adsorbed CO2 species. This is the same mechanism as reported by Belton and co-workers for the kinetics of the reduction of FeO. This explains why the reduction of metal oxides in slags by hydrogen is often faster than by CO.

Jan 1, 2003

By S. H. Castro

In 1997 Chile was the world's largest copper mine producer with around 3.4 million metric tomes of copper. Conventional technology (conminution-flotation- smelting-converting-electrorefining) for copper sulfide ores was used. For copper oxidized ores hydrometallurgical processes (heap leaching-solvent extraction- electrowinning) were employed. Consequently, the most important waste effluents include flotation tailings, gaseous emissions, smelter slags, acidic and alkaline wastewater, electrolytic sludges, solid residues from leaching, etc. The introduction of stricter environmental regulations are forcing the Chilean industry to minimise the generation of waste and promote cleaner production. Gas emissions such as SO2 and arsenic from smelters and process wastewater are the major problems at this stage. The environmental impact assessment of gas emissions in all six largest smelters namely Chuquicamata, Caletones, Potrenllos, Ventanas, Paipote and Chagres led to design a "decontamination plan." The implementation of this plan resulted in (i) the installation of sulfuric acid plants for SO2 abatement and (ii) the installation of electrostatic precipitators to remove arsenic oxides condensed from cooling gases. The aim of this paper is (i) to describe the type of waste associated to the various stages of the metallurgical processes and (ii) review the main abatement technologies used in medium and large size companies.

Jan 1, 1999

By D. B. Dreisinger, V. van der Pas

Zinc sulphate electrolyte used for zinc electrowinning must be purified for cObalt ions. The cobalt is removed in a cementation stage by the addition of zinc dust. Copper arid antimony are frequently used additives which enhance the cementation of cobalt. This paper aims at a better understanding of how copper and antimony promote the removal of cobalt. Initial experiments were done in a batch cementation reactor. Copper and antimony precipitated in the early stages of cementation indicating that a preferential substrate was formed. The individual role of copper and antimony was further investigated in an electrochemical cell. On a microsca1e, the , growth process, morphology and the composition of the precipitates were examined with SEM and XRD. It was found that cobalt could not be deposited in its pure form but as a cobalt-zinc alloy with zinc as the prime constituent. Copper increases the cathodic surface area of zinc dust by precipitating as numerous dendrites. Antimony acts as a cathodic surface onto which a cobalt-zinc alloy with an increased cobalt content is deposited.

Jan 1, 1997