Search Documents

By Fu-Shen Zhang, Mengjun Chen, Jianxin Zhu

"A novel approach for foam glass preparation, namely vacuum-aided powder sintering technique, was preliminarily investigated in the present communication. The key point of which was to prepare foam glass at a negative pressure. Compared to normal powder sintering process, the new approach could benefit the foaming process by shorting the holding time, reducing the amount of foaming agent and especially decreasing relative density of the product. Optimum conditions were 750 °C, 1000 Pa, 5 min and 1 wt.% foaming agent, respectively.IntroductionFoam glass represents a highly valuable solution for thermal and acoustic insulation, since it possesses a generally higher mechanical, chemical and thermal stability than other foams'1'. The first industrial processing for foam glass production, the direct introduction of gases (""blowing"") into the special molten glass, can be dated back to the end of 1930s'2'. At present, almost all foam glasses is prepared by powder sintering technique instead of blowing,3 since it reduces the temperature by several hundred degrees. Moreover, as fine glass powders or similar powders can be used to substitute corresponding glasses by this technique, considerable attention has been focused on the production of foam glass by considering fully recycled glasses, coal fly ash, or other solid wastes as raw materials,4 especially CRT glasses'3' 5', on the point of environmental protection.In a previous report'6', when discussing the lead removal and recovery from CRT funnel glass by a pyrovacuum process, we found that foam glass could be prepared at a negative pressure. Therefore, in this communication, the similarities and differences between the powder sintering process for foam glass at normal and negative pressure was preliminarily discussed."

Jan 1, 2011

By Yogeshwar Sahai

Submerged gas injection into melts contained in furnaces, ladles, or similar transfer vessels is commonly used in industrial practice. In this review paper, conditions leading to gas bubble formation at the nozzle are first summarized. The increasing gas injection rates and other conditions, such as nozzle size, lead to regimes which are commonly known as "bubbling" and "jetting". These are explained. The gas/melt interactions result in energy transfer to the melt. In recent years, a large number of researchers have investigated the relationships between the energy density and the mixing times. Their work is reviewed, and the mixing mechanisms is described. Finally, computational approaches of modeling submerged gas injection are briefly presented.

Jan 1, 1993

By R. R. Odle

A laboratory and pilot-scale investigation of direct smelting of copper concentrates was conducted to determine the effect of concentrate analysis and the degree of roasting on the yield and quality of copper produced in a subsequent smelting step. A stoichiometric :mOdel of direct smelting is presented which predicts the? quantity of copper; slag, and white metal' prOduced'and the distribution of copper in these phases as a function? of the concentrate '(calcine) analysis.

Jan 1, 1983

By Zengjie Wang

Investigation on hydrochloric acid leaching of the ilmenite from Panzhihua, China was carried out to prepare synthetic rutile. The leaching parameters were optimized to obtain high content of TiO2 in the products. The experimental data suggest that an optimum leaching can be realized with 30% acid, a solid/liquid ratio of 1/4 at 95°C for 4h, and ore ground for -400 mesh size. After the acid leaching, an additional alkaline leaching process using hot NaOH solution was performed, and then the products was in grain form followed by heat treated at 900°C for 2h in order to extract Si and increase the particle size of synthetic rutile. The final product has a high content of TiO2 (about 95%), a low content of chlorine consuming elements (total CaO+MgO =0.07%) and a suitable particle size distribution for chlorination process.

Jan 1, 2008

By Julian Johnson

The effect of changing redox potential (Eh) on the high temperature sulfuric acid leaching of Western Australian dry-land nickel laterite ores has been investigated. In particular, the effect of added reductant (sulfur, sodium sulfite) or oxidant (potassium chromate) on Eh, leaching kinetics, metal extractions, acid utilisation and leach residues has been determined. Three separate ores - nonhonitic ores from Murrin Mumn and Bulong, and limonitic ore from Cawse - were used in the study. Sulfur addition varied from 0 to 7.8 kg/t ore. The total acid loading was kept constant at 430 kg/t (Murrin Murrin ore) and 330 kglt (Cawse ore), whilst acid loading for Bulong ore was varied according to the presence of either reductant or oxidant. The extraction of both nickel and cobalt from limonite ore remained unaffected when small amounts of sulfkr were added, but addition of even small amounts of reductant to nontronitic ore decreased both nickel and cobalt extraction. Increased manganese and iron dissolution were observed as the levels of reductant increased, accompanied by a decrease in chromium dissolution. As the iron dissolution increased, free acidity decreased, with a subsequent decrease in nickel extraction. In contrast, addition of oxidant lead to reduced iron and manganese dissolution and slower extraction of nickel and cobalt. Keywords: Limonite, Nonhonite, Eh, Nickel Extraction

Jan 1, 2004

By Vladimir Mindin

This paper presents results of thermodynamic investigations and experimental' studies of some essential for pyrometallurgy of sulfide concentrates topics. Among them: 1. Thermodynamic simulation and experimental investigations of roasting process, 2. Thermodynamic investigations of sulfur dioxide off-gases treatment technologies. 3. Investigations on "Mind in -Kiknadze" effect of suppression of sulfur dioxide formation during sulfide concentrates roasting in the vapor containing atmosphere. 4. Thermodynamic simulation and experimental investigations of sulfide concentrates and manganese containing materials co-roasting processes. Some essential aspects of thermodynamic simulation techniques are also discussed.

Jan 1, 1998

By J. F. Leroux

The Gaspé smelter at Murdochville, Quebec, Canada introduced concentrate injection into elongated Peirce-Smith converters sized 1.96m x 12.5m (13 ft. by 41 ft.) in 1996, and commissioned a large, converter-like bath smelting vessel in April 1998. The new vessel, which is sized 4.27m x 16.1 5m (14ft. by 53ft.) has several interesting features designed to effectively utilize bath smelting technology for the requirements of the Gaspé smelter. For example, the vessel can operate on concentrate injection at upwards of 60-80 tph rate on an instantaneous basis, can operate as a large Peirce-Smith converter, while it is also fitted with matte and slag tapholes much akin to Noranda Process reactor, and includes a novel cold charge addition system. The new technology will eventually allow the capacity of the plant to increase from about 300,000 tonnes of concentrate per year to over 350,000 tonnes of concentrate per year while improving sulfur capture.

Jan 1, 1999

By H. Y. Sohn

A novel solvent extraction process in which the emulsion is generated by bottom gas injection rather than mechanical stirring has been developed. This process has a number of advantages over the mixer-settler unit or the spray column in terms of simple equipment configuration and the ease of cleaning and process control while providing a large interfacial area for mass transfer. The equipment consists of a horizontal cylindrical vessel in which the two immiscible liquids flow countercurrently. High-strength gas jets are injected from the bottom at certain intervals along the length of the vessel. The gas jet creates a plume zone consisting of an emulsion of the two liquids which contains a large interfacial area for rapid mass transfer. The two liquids then disengage and flow in the opposite directions before entering another plume zone. Thus, the process combines the simplicity of a cylindrical vessel, having no moving parts, with the contacting efficiency of a mixer-settler. The gas can be recycled in a closed loop, thus eliminating mist and other emission problems. These advantages would be especially significant for treating large-volume/low-value liquid streams which contain hazardous substances and/or suspended solid particulates.

Jan 1, 1996

By Flávia Paulucci Cianga Silvas, Otávio da Fonseca Martins Gomes, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Jorge Alberto Soares Tenorio, Guilherme Apostólico Bortolini, Stoyan Gaydardzhiev

"Printed circuit boards (PCB) are particularly problematic to recycle because of the heterogeneous mix of organic materials, metals, and glass fiber. PCBs are found in almost every electroelectronic equipment and their recycling process involves a pre-treatment to separate the products which contain targeted metals. In this work, a physical processing involving sequential shredding and hanuner milling were used to obtain a comminuted sample from scrap printers PCBs. The thus prepared sample was analyzed for particle size distribution and by optical microscopy as well was subjected to pyrolysis, leachabilty and chemical composition determination by XRF. The metals concentration was determined by ICP and AAS. The PCBs have been also analyzed by SEM-EDS (micro-analysis and X-ray mapping). The results show that the studied PCBs are lead free, multilayer with 4 copper layers, have 45% of metals and the copper is present in significantly higher concentration than the rest of the metals.IntroductionThe global generation of e-waste (electrical and electronic equipment waste - WEEEs) grows at a rate of about 40 millions of tons per year [ l].Among this e-waste there are PCBs that are present in almost all electronic equipment. Their composition is heterogeneous and varies according to several factors, including: kind of EEE, when and where it was produced, fabrication technology [2], etc. In printers, the PCBs represent about 6.6- 8 wt.% [3].The PCBs treatment may include physical, pyrometallurgical, hydrometallurgical, ectrometallurgical and more recently bio-hydrometallurgical process. Normally there is a combination between these processes [2, 4, 5, 6, 7, 8, 9, 10].The diversity between the different PCBs composition complicates the recycling process since the composition of metal and others materials can vary according to the models. So characterization is an indispensable step before any processing of PCB to begin. Owing to the above said, the main goal of this work has been set to characterize representative samples of PCBs from printers through physical, chemical and microstructural analyses."

Jan 1, 2014

By A. V. Tarasov, A. D. Besser

A processing flowsheet has been developed for treating substandard lead-containing polymetallic bulk concentrates and intermediate flotation products containing precious metals, which comprises oxidizing roasting in a calcination kiln and electrothermic smelting generating low volumes of off-gas. The proposed flowsheet also incorporates a dust collection system and sulfur dioxide recovery from off-gas. It is proposed to implement this process by using a reaction smelting technique. For this purpose, the charge to be fed to the smelting furnace after its calcination in a drum-type rotary kiln must have a ratio of sulfide sulfur to sulfate sulfur of at least 1 :2. Electric smelting makes it possible to produce lead bullion that also collects the precious metals contained in the feed, as well as copper-lead matte and slag containing zinc. The recovery of lead into lead bullion and into matte is approximately 83% and 14%, respectively (thus the overall recovery is 97%); the total recovery of gold and silver into lead bullion and matte is 98%; th\lt of copper into matte is 89%; the recovery of zinc into slag is 96%; and that of sulfur into sulfuric acid or gypsum is 90%. After the recovery of zinc from slag, the latter can be utilized in the construction industry.

Jan 1, 2000

By Larry M. Southwick

The smelting of copper and other non-ferrous metals have made considerable advances over the last 125 years. Many of the ideas and processes currently in use were attempted early in the history of smelting and were unsuccessful. Often the cause was incomplete understanding of the metallurgy involved, inadequate refractories, poor materials of equipment fabrication or trying too many new ideas at once. With time, these problems get solved and the technologies become commercialized .These were processes whose time had not come when originally proposed, but did eventually. On the other hand, there have been some concepts whose time will never come. They were impossible then and they are impossible now. The people that dream these up were either crackpots (they didn't know what they were doing, but thought they did), or charlatans (they knew they didn't know what they were doing, but didn't care). Both rely on bad science to propose metallurgical absurdities. These too have their place in the development of technology, though mostly negative, and several examples will be discussed in this paper. Three from around the turn of the century will be covered, as well as one from this decade. The last demonstrates that the art of creating absurdities has not withered, even after ninety years of scientific sophistication, and some can even be patented. The first three reached field trials due to the gullibility of company management. The last arose from a fortuitous mis-operation of a plant which solved a problem, but the explanation and patent which arose are metallurgically impossible.

Jan 1, 1999

By Ahmad-Bitar¸ Riyad N., Shadia J. Ikhmayies

"CdSi-xTex thin films with O<x<0.3 were prepared on glass substrates by the annealing of CdS:In thin films produced by the spray pyrolysis technique. The annealing was performed in nitrogen atmosphere at 400 --,C in the presence of Te vapor. The compositions of the films were determined by energy dispersive X-ray detection (EDAX) measurements. Scanning electron microscopy (SEM) was used to investigate the morphology of the films. The transmittance of the films was measured at room temperature in the wavelength range 400-1100 nm and used to produce the absorbance of the films. The first derivative of the absorbance was used to estimate the optical bandgap energy Eg by using the minima in the first derivative. The relation between the bandgap energy and the fraction x was found to fit with a parabola and bandgaps in the range 2.196: =Eg: =2.480 e V were obtained. Urbach tailing in the bandgap was also investigated.IntroductionPolycrystalline thin film CdS/CdTe solar cells are promising candidates for low cost and high efficiency photovoltaic applications. The fabrication process of these cells involves the deposition of a p-type CdTe absorber layer on top of an n-type CdS one which acts as a window. The efficiency of the solar cell is affected by the method of preparation of both layers [1, 2].Interdiffusion processes taking place at the CdS/CdTe interface have largely been realized to significantly affect the device performance [3] by changing the bandgap of both CdTe and CdS which modifies the spectral response of the solar cell [ 4]. The formation of a mixed crystal or a graded layer causes a reduction in the lattice mismatch at the CdS/CdTe junction [5] which is about 9% [ 6] and then a reduction in the number of interfacial states and recombination centers, thus enhancing the solar cell performance [7, 8]. A complete understanding of the properties of the intermixed layers CdSxTe1-x that usually constitutes the interfacial region in the CdS/CdTe solar cell is essential. According to our knowledge, a lot of research was devoted to the investigation of the diffusion of S into CdTe [3-5, 9]; but little on the direct investigation of the diffusion of Te into CdS [6]."

Jan 1, 2011

By Mohamed Ahmed, A. Kawy

"Smelting of scrap copper and residual anodes and cathodes carried out in a reverberatory type furnace. In this, deoxidation process is carried out by wood, which acts as a resource of reduction gases such carbon monoxide, hydrogen and methane. Use of wood causes the formation of soot pollutants and efficiency of oxygen removal from copper is low leading to added costs in removing contaminants. This expensive problem was solved by using of reformed natural gas as a source of reduction gases (CO+ H2).IntroductionThree reverberatory furnaces were used for smelting of scrap copper and residual anodes and cathodes. Each furnace had a 7tpd capacity and was operated at 1183 °C.In this furnace, Step1-compressed air supplied by tubes from the side of the furnace to remove sulfur from copper matte by oxidation .The copper is also oxidized to copper oxide .[1]Step 2- copper from matte is deoxidized by a reductant. Typically deoxidation process is carried out using wood as a resource of carbon monoxide, hydrogen and methane which are the reduction gases. Use of wood causes the following:1- Forms soot pollutants2- Oxygen removal efficiency from copper is low; more contamination in copper matte increased energy in deoxidation3-the process is highly expensive.In the recent trends, this problem has been solved by using reformed natural gas as a source of reduction gases (CO+ H) .This results in 1-Reduced pollution during smelting.2- High efficiency in the removal of oxygen from copper to produce oxygen free copper. The surface of copper produced from this method is smooth which helps in forming and machining.3- Low cost and natural gas is more readily available in Egypt than wood."

Jan 1, 2010

By Norbert Steiner

For the desulfurization of weak SO2 gas streams, Degussa developed a process using dilute H2SO4 solution containing H2O, instead of conventional gas scrubbing with all solid absorbent medium (limestone, MgO). The process is based on fast reaction of H2O, with SO2 yielding H2SO4 up to 70% strength, depending on off-gas temperature. Compared to the conventional systems with typically < 95% efficiency, independent on the raw gas SO2 concentration, residual SO2 concentrations of less than 20 mg/Nm3 can be easily achieved, corresponding to nearly 100% removal. These features render the H2O, process a very attractive, low capital cost technology to retrofit existing conventional desulfurization plants.

Jan 1, 1996

By J. R. Sarazin

Density driven convection during solidification has been recognized for some time to result in macrosegregation particularly when lower density alloying elements are rejected into the interdendritic liquid. The resulting segregates are commonly referred to as channels, freckles or A-segregates. Buoyancy driven convection leading to channel formation has been examined in three model systems possessing somewhat different materials parameters. They are the Pb-Sn eutectic system, the transparent aqueous-salt NH C1-H 0 4 2 eutectic system and the transparent organic succinonitrile-ethanol monotectic system. Convection in these systems is controlled by a balance of buoyant and viscous forces, which are strong functions of composition and temperature. Composition, temperature and flow velocity were measured and elimination of channels through heavier ternary additions is discussed.

Jan 1, 1991

By Caisa Samuelsson

Experimental studies in laboratory-scale equipment have been carried out to study the vaporisation from dust generated during the copper converting process. In the present work the vaporisation of Zn, Pb, As, Sb, and Bi from a dust collected in the electrostatic precipitator after the copper converter were studied. The results show that Pb, Bi and As were vaporised to a high degree from the dust at a temperature above 900°C in a gas containing N2, SO2 and a small amount of H2. The vaporisation was high for these elements also in a gas containing N2, SO2 and 02 at temperatures above 1120°C. In an earlier study, thermodynamic calculations showed that it is possible to selectively condense metals at high temperature&apos; in a gas atmosphere generated during a copper converting process. The present study was carried out to verify the thermodynamic model. The results indicate that it should be possible for a selective condensation of Zn at high temperature. The temperature required for a selective condensation of Zn is dependent upon the gas atmosphere, e.g., the oxygen potential.

Jan 1, 1998

By Gervais Soucy, François Quesnel, Pierre Hovington, Wen Zhu, Karim Zaghib, Jocelyn Veilleux

The properties of lithium titanates anodes in Li-ion batteries are highly dependent on their secondary constituents. While their main phase is usually constituted of Li4Ti5O12, significant quantity of lithium titanates compounds of various stoichiometry are often present, due to either the processing, usage or aging of the material. These may go underreported, as many of these spectrums overlap or display low signal in X-ray diffraction (XRD). Samples of nanosized lithium titanates synthetized by inductive plasma were characterized by XRD and scanning electron microscopy (SEM), as they provide a regular yet typical crystallite size and shape including multiple phases. A Rietveld refinement was developed to extract the composition of these samples. Mass balance through further annealing and differential scanning calorimetry (DSC) enthalpy measurements from phase transformations were also used as identification and validation techniques.

Jan 1, 2015

By M. Soltanieh

The liquidus surface? and tie-lines in the nickel-cobalt-sulphur ternary system have been determined between 1<273-1573 K. The experiments were conducted by equlibrating the liquid sulphide with the metallic alloy phase. The liquid sulphide phase was sampled and chemically analyzed. The alloy was analyzed by electrol} microprobe. Combining the present results with the.avai1abl~ literature data, the thermodynamic properties of this system were calculated.

Jan 1, 1998

By Mark Kruzynski, Srinivas Garimella, James T. Wiswall

"A flue gas recirculation (FGR) system for a combustion fired aluminum melting furnace is experimentally investigated. The FGR system flows combustion air in a turbulent jet within the flue gas stream, and the turbulent jet flow is collected in a tube at a distance from the jet exit. Entrainment of the flue gases as well as heat transfer between the flue gases and the jet occurs over the length of the exposed jet. Heat transfer between the flue gases and the jet, and the amount of flue gas entrained into the jet (derived from temperature, flow rate and oxygen fraction measurements) were measured as a function of nozzle exit velocity and the distance between the nozzle exit and collection tube. In addition to flue gas entrainment, a fuel savings of up to 7%, due to heat transfer over the length of the jet, was projected from the measurements obtained.IntroductionFlue gas recirculation can be applied to aluminum melting furnaces to control combustion temperature. When coupled with a device to improve furnace efficiency by recovering heat from the furnace exhaust, flue gas recirculation provides a control technique that is integral to achieving the goals of reducing fuel consumption, increasing product yield, increasing the longevity of infrastructure, and reducing pollutant emissions. In particular, combustion temperature control can help reduce reactivity of the products of combustion with the molten metal surface and furnace refractory materials. Combustion temperature control can also help improve the life of heat exchangers used to recover energy lost to the environment in the flue gases, and reduce NOx formation in the combustion process. Flue gas recirculation can also dilute oxygen used in oxy-fuel combustion to reduce reactivity.Flue gas recirculation has been used since the 1970s to control flame temperatures in the automotive industry [1-3] and has successfully reduced NOx emissions. Many different flue gas recirculation approaches for high temperature melting such as melting aluminum and glass have been patented since the 1980s [4-12]. There has also been academic interest to determine the fundamental performance characteristics of flue gas recirculation in high temperature furnaces and in combustion [13-15]."

Jan 1, 2014

By I. J. Moon

The reduction behavior of hematite by H2 and H2-CO gas mixtures was investigated to elucidate the reduction mechanism at 800-950 °C. The hematite compacts were made by Cold Isostatic Pressing to produce compacts of uniform shape and size. The compacts were sintered at 1000° C for 30min, and showed a contraction of 29%. Mercury pressure porosimeter was used for measuring the total porosity, pore size distribution and pore surface area of the compacts. Reduction was measured by means of weight-loss technique using Cahn Balance (Model : TG-171, capacity log, accuracy f 10pg). Microscopic examination and X-ray analysis were used to correlate the structure of reduced compacts with the mechanisms of reduction. Neither chemical reaction control nor diffusion control is adequate in describing the complete course of reduction of the hematite compact. The reduction of hematite compacts was initially controlled by the chemical reaction at oxidelmetal interface. The reaction goes through a transition phase .where it is undergoing a mixed control, followed by the diffusion control towards the end of the reduction. The values of apparent activation energies for chemical reaction control were 3.48-8.43 kcal/mol depending on the gas compositions.

Jan 1, 1997