Search Documents

By Kenneth G. Thomas

This paper reviews the alkaline and acid gold autoclaving experiences gained at Barrick Gold Corporation. Alkaline autoclaving was operational at Barrick Mercur, Utah, U.S.A., on carbonaceous/sulphide refractory ore for eight years commencing in 1988. Acid autoclaves have been operational at Barrick Goldstrike, Nevada, U.S.A., on sulphide refractory ore since 1990 and now process 17,500 stpd of ore through six large autoclaves. Information is presented on operating costs, materials of construction, reagent requirements and flow sheet developments that reduced capital and operating costs.

Jan 1, 2000

By G. J. Abbaschian, A. B. Gokhale, M. M. Kunjapur

"A laboratory scale model furnace was constructed for obtaining radially inward oriented columnar grains in disc shaped castings. The furnace consisted of eleven circular, concentric, equispaced resistance heaters on each half of a split graphite mold. Water or air flowing through a copper pipe along the periphery of the disc constituted the heat sink. After filling the mold, the heaters were turned off consecutively in top and bottom pairs from the rim towards the center, causing the temperature gradients to move inward. Equiaxed structure was obtained at the center by turning off the inner coils together when desired. Sn:15%Pb alloy was used to cast integral blade disc castings using the above technique to obtain dual-property discs with a central equiaxed structure and an outer columnar grain structure projecting inwards from the blades to the rim. A numerical technique was used to predict the temperature profile in the disc during solidification, and good correlation was obtained with the experimentally measured temperature profiles. The corresponding heat transfer coefficient values obtained were h = 544 Wm- 2k-1 (0.013 cal/cm2- ° C-sec) for cooling between metal and chill and h' = 71 Wm- 2k-1 (0.0017 cal/cm2- ° C-sec) for the heat input from the hot mold to the liquid metal. BackgroundHigh temperature alloys used in the current generation of gas turbine engines have evolved through two main stages of development: in 1950's, the increase in the efficiency of gas turbines was paced by improvements in alloy design, which led to the development of Ni and Co-based superalloys (1). By mid-1960's, it was realized that improved alloy chemistry alone was inadequate in meeting the increasingly stringent service requirements. The focus of research then shifted from alloy development to process development, and resulted in the introduction of directional solidification (DS) techniques for the production of turbine blades and vanes (1,2).Under typical operating conditions, the blades and vanes are subjected to aerodynamic loading, while the blades are additionally subjected to high centrifugal loading and vibratory stresses. The primary material requirements for blades may be summarized as follows (1,3):•,High creep resistance•,Good high temperature tensile strength (typically in the range of•,275 to 550 MPa at temperatures in excess of 750°C)•,Resistance to both low cycle and high cycle fatigue (LCF and HCF)•,Resistance to erosion, corrosion, and oxidation•,Resistance to thermal fatigue"

Jan 1, 1986

By K. D. Peaslee, V. L. Richards, C. H. Rawlins, S. N. Lekakh

"Steel-making processes generate carbon dioxide air emissions and a slag co-product. The aim of this project was to develop a functional sequestration system using steelmaking slag to permanently capture carbon dioxide emitted in steelmaking offgas. A possible parallel benefit of this process would be rapid chemical stabilization of the slag minerals with reducing swelling or leaching.This paper summarizes the original results of the project, including mineralogical and structural features of carbon sequestration with steel making slag, mathematical modeling of reaction phenomena using a modified shrinking core model, METSIM modeling of several possible industrial applications, a thermo-gravimetrical study of the reaction between slags and different gases, and design and testing for a lab scale apparatus consisted of two reactors.1. IntroductionThe U.S. produces 9-14 Mt of steelmaking slag annually, which represents approximately 10-15 wt. % of crude steel output.1,2 Primary uses for steelmaking slag include high quality mineral aggregate, Portland cement, unconfined fill, soil conditioning, and pH neutralization of abandoned mine drainage.3,4 The key factor prescribing slag use is the alkaline-earth metal (e.g. Ca and Mg) oxides content, which contribute to overall basicity and cementitious strength. However, as-produced steelmaking slag is chemically unstable. Calcium and magnesium oxides readily form hydroxides and carbonates through reaction with atmospheric gases. Both hydroxide and carbonate formation produce substantial mechanical swelling leading to heave failure in confined construction applications, thus many states dictate stockpile aging for 3-6 months prior to commercial use.5,6 Sequestration of carbon dioxide is a natural corollary to forced carbonation. The conversion of CaO/MgO to carbonates serves both to stabilize the slag, and permanently capture and store the CO2."

Jan 1, 2008

By Yuanbo Zhang, Yongbin Yang, Guanghui Li, Zhengwei Yu, Yufeng Guo, Tao Jiang, Xiaohui Fan, Youming Hu

"Composite agglomeration process (CAP), as an innovative method for preparing blast furnace burden, was developed and has been put into operation in China. CAP is different from traditional agglomeration processes of iron-bearing materials involving sintering and pelletizing. Compared to the traditional agglomeration processes, CAP is characterized by several strengths such as permission of diverse iron-bearing materials in production, obvious improvement of permeability in the feed bed, decreasing the fuel consumption and remarkably increasing the productivity of sintering machine. Furthermore, the use of the composite agglomerates prepared with CAP is capable of obviating the negative effects caused by the differences in quality of sinter and pellets on the operation of blast furnaces. This paper mainly presents an overview of the principle and applications of CAP.Development Background and Principle of CAPhe traditional agglomeration processes including sintering and pelletizing have been the two predominant methods for preparing ironmaking burden from iron-bearing materials. Sintering is a way for agglomeration by heating the coarser fine ores (general granularity 0~10mm). The mechanical strength of irregular porous sinter is obtained by the solidification of molten phase at high temperature process. It has been shown that the production of high basicity sinter (R=1.8~2.2) is characterized by low energy consumption and high efficiency compared to low basicity sintering. Meantime, the finished high basicity sinter is characterized by good mechanical strength and metallurgical performance. Pelletizing is another way for agglomeration by firing wet green pellets, which are balled from the fine grained iron ores or concentrates. Based on the differences of chemical compositions, the finished pellets can be divided into acidic oxidized pellets, fluxed pellets, magnesium-bearing pellets, and so on. The acidic oxidized pellets are the dominant products of modern pelletizing."

Jan 1, 2012

By Keith M. Axler

This report addresses issues specific to the generation of hydrogen fluoride via reaction of calcium fluoride with sulfuric acid. This process has been established on a commercial scale and is under consideration for treatment of calcium fluoride residues from uranium processing. Magnesium fluoride slags are also available as a product of uranium processing. The technique of using sulfuric acid for the production of hydrogen fluoride from magnesium fluoride is also under consideration as a residue processing scheme. In the current study, thermodynamic modeling was used to investigate these chemical processing systems. The results presented herein reveal information relevant to the selection of processing temperatures and conditions. Details include predicted effects in system composition based on operating temperatures for both the calcium fluoride and the magnesium fluoride systems.

Jan 1, 1996

By Mathilde Guilpain

A wide variety of plants are able to extract nickel (Ni) from soils and accumulate this metal in their foliage. Hydrometallurgical processes have been developed to recover Ni in the form of metal or salts, starting from the plant A. murale. They include: (1) a combustion step, to obtain ash containing 15–20% Ni; (2) a leaching step; and (3) purification. That whole flowsheet has been thoroughly investigated, and the processes scaled up to the pilot scale. Another strategy is presented here, consisting of recovering Ni without burning the plant. Ni can be extracted from the dry plant by water leaching, but the leachate is a multi-element solution from which Ni has to be separated. Selective precipitation of Ni hydroxide is not possible since Ni is bound to organic ligands. In this work, the plant leachate is processed by adsorption on the chelating resin DOWEXTM M4195. The results showed that Ni was selectively retained whereas the other main cations were not. Nickel could be recovered at the elution step. This methodology needs to be further investigated but these initial results are very encouraging and open the possibility of Ni recovery by agromining.

By Denise C. R. Espinosa

Rechargeable lithium batteries are one of the most promISIng technology in battery development. Although Li ion batteries have been used as an alternative to the more polluting and less performing Ni-Cd batteries, Li ion batteries have limited life and their disposal is uncertain. It is imperative that valuables from wastes, such as lithium, should be recovered. The main objective of the present work was to characterize secondary lithium batteries for cellular phones. This was done using unit operations of mining processing, x-ray diffraction (XRD), chemical analyses and the rmogravimetric analysis (TG). The unit operations were hammer mill grinding, knife mill grinding, size separation and magnetic separation. After the hammer grinding process, the plastic cases were almost intact, however, they have released the cylindrical lithium batteries themselves and these parts correspond to 70% of the total battery weight.

Jan 1, 2001

By E. Fregeau-Wu

The major obstacle in recycling steelmaking slags to the blast furnace is their phosphorus content. Removal of the phosphorus, which is primarily associated with the silicate and phosphate phases, would allow for greater recycle of these slags for their iron, manganese, and lime contents. Calculations show that separation of the silicates from the oxide phases would remove nearly 90% of the phosphorus from the slag. The variable grain size of the as-received slag made liberation by fine grinding difficult. Therefore, slow-cooling experiments were undertaken to improve the grain size distribution. The grain size distributions were determined using in-situ image analysis. The samples were ground to their apparent liberation size and high gradient magnetic separation was used to separate the magnetic oxides from the nonmagnetic silicates and phosphates. Liberation analysis and modeling was performed on selected separation products for discussion of benefication characteristics.

Jan 1, 1995

By Ann M. Hagni

"Ceramic matrix composites are inorganic materials that are particularly resistant to heat and abrasion. A magnesia (MgO) and aluminum nitride (AlN) based composite is formed by exposing a magnesia preform to a metallic alloy block in a nitrogen atmosphere at 950°C. The metallic alloy, which is composed primarily of aluminum, is wicked into the preform. Aluminum nitride matrix is grown between MgO particles as the wicked metallic aluminum reacts with nitrogen. Unused metallic alloy, remnant metallic alloy (carcass), and composite produced after 8 hours, 50 hours, and 225 hours of processing are characterized mineralogically. Reflected light microscopy, transmitted light microscopy, scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffraction techniques reveal that in addition to anhedral to euhedral AhNi, AbSbSr, and Al crystallizing in the metallic alloy carcass, AIN and (Al,Si)N have formed as well. Nitride rings and nodules in the carcass may hinder AIN growth in the composite. Fine-grained residual AhNi and AhShSr are dispersed throughout the composite matrix. The nitride matrix is composed of AIN and (Al,Si)N. Rim replacement of MgO by spine! occurs in the composite. Aluminum nitrides in the metallic carcass cathodoluminesce deep violet-blue, unlike non-luminescent AIN in the composite matrix. This distinction in cathodoluminescence suggests a different mode of formation for composite AIN than for carcass AIN. Phase interpretations and textural characterizations deduced from the implementation of sophisticated mineralogical techniques have contributed to the understanding, and will aid in the improvement, of MgO/ AlN-based ceramic matrix compositeprocessing."

Jan 1, 1999

By Zhenbo Zhao

The processes and equipment for INLRFH (Isothermal Normalizing by Utilizing the Residual Forged Heat) of alloy carburizing steel products are presented. It is shown that four key parameters: namely (I) cooling rate before isothermal normalizing, (IT) the lowest cooling temperature before isothermal normalizing, (111) isothermal normalizing temperature and (IV) isothermal normalizing time, should be controlled. The prediction and calculation of these parameters can be achieved on the basis of components treated and the technical requirements of the steel parts by an on-line expert system. The cost-reductions due to the energy savings resulting from implementing this system for automotive parts heat-treatment are most promising.

Jan 1, 1999

By Toshiyuki Hashida, Victor M. Lopez-Hirata

"Small-punch tests and determination of fracture toughness JIC were conducted at 4 and 77 K on new cryogenic JN1, JJ1 and JK2 austenitic stainless steels, after isothermal aging. Equivalent fracture strain ?qf determined by measuring the reduction of thickness in the small-punch test specimen. A linear dependence of JIC on ?qf was found in these new materials. Regression analysis of experimental data produced the following linear relation JIC = 1304.1 ?qf + 8.09 [kJm-2]. An analysis of present work relation was pursued on the basis of material properties and evaluation method of he. Results showed that the slope value has a strong dependence on material yield strength and JIC evaluation method. This linear relation is useful for the evaluation of fracture toughness JIC, measuring the equivalent fracture strain ?qf by means of small-punch test. Thus it can be useful for assessing the degradation of fracture toughness in small areas such as, the heat-affected zone in welded components.IntroductionCryogenic structural materials for superconducting magnets of fusion nuclear reactor are required to possess a good combination of strength and toughness. The mechanical properties are required beyond the capability of conventional austenitic stainless steels [1]. New cryogenic JN1, JJ1 and JK2 austenitic stainless steels were developed by the Japan Atomic Energy Research Institute (JAERI) [1]. The structure of superconducting magnets is constructed by welding of 200 = thick plates of these steels, which are solution treated at high temperatures and then water-quenched to avoid intergranular precipitation. However, the welding process involves heating and cooling [2], which cause microstructural changes in both base metal and weld. In this heterogeneous microstructure, it is important to estimate the fracture toughness of these materials at cryogenic temperatures. Therefore, it is necessary to evaluate the effect of aging process on the fracture toughness behavior of these new steels. To determine the cryogenic fracture toughness, the elastic-plastic JIC value has been co=only used [2]; however, the specimen size is much larger than heat-affected zones in welded components. Small-punch (SP) testing method, employing miniature specimens, has permitted to evaluate the fracture toughness behavior at different temperatures in different nuclear reactor materials [3,4]. Mao et al. [5,6] and Misawa et al. [7] found a linear relation between JIC value and equivalent fracture strain ?qf, determined by SP method in non-ferrous alloys and ferritic steels at room temperature and austenitic stainless steels at 4 and 77 K, respectively. So that, this kind of correlation would be very useful to assess the fracture toughness JICe values by means of SP test in small zones of welded components."

Jan 1, 2012

By M. Sakamoto, S. Karaswa, Y. Yoneoka, Y. Ohmizo

"The Annaka Refinery has been processing leach residue by Waelz process for 17 years. Recently, the quantity of the leach residue has increased due to a decline in the quality ~f zinc concentrate. Meanwhile, negative factors (e.g. deterioration of water balance due to improved electrolytic power consumption rate) have increased· in the processing of the leach residue.We have implemented various measures in responses to this situation, while striving to increase ·processing capacity and achieve stable operation. AS we have largely completed our assessment of the efficacy of these measures, we report on our recent process improvements.IntroductionWe have been treating leach residue by the Waelz kiln process since 1981. At that time, treatment of only 50,000 tons of leach residue per year was anticipated. However, subsequent process improvements have revised this figure up to 75,000 to 80,000 tons per year.However, today's increased Fe zinc concentrate grade has resulted in increased amounts of leach residue. In addition, improvements have reduced electrolytic power consumption rate of zinc electrolysis, limiting the amount of water that can be used in ·the zinc refining processes and for deaning leach residue. Consequently, we encounter an increasing number of problems and factors adversely affecting leach residue treatment, including increases in water-soluble Zn (WsZn) and. S (S04) in leach residue.To solve these problems, we have taken several measures to ensure long-term continuous operation and treatment of this increased · amount of leach residue. This paper discusses these measures."

Jan 1, 2000

By Irshad A. Rana

In a modern copper smelter, the capital cost of a sulfuric acid plant constitutes the largest single cost item of the total investment. It is thus essential to properly size the acid plant in order to reduce its capital cost and enhance the economic viability of a new smelter project. Whereas the off-gas from a smelting furnace is continuous and generally uniform, the gas flow from the Peirce-Smith converters is intermittent with significant fluctuations. The converters off-gas volume is dependent upon a number of interrelating factors. The most significant factors are the matte feed grade, the system air infiltration, the converter's size and blowing rate, the maximum number of converters simultaneously blowing and the gas cooling system employed. The acid plant size, therefore, is heavily influenced by the converter off-gases. Several of these factors are discussed, and their impact in determining the acid plant size is explored.

Jan 1, 1993

By G. G. Richards

The zinc slag fuming process is used to recover zinc from molten iron-calcium silicate slags by treatment with pulverized coal and air. The rate of zinc fuming is controlled by the complex interaction of several kinetic factors including the rate of entrainment of coal in the slag, the extent of the coal-slag reaction and the rate of ferrous oxide oxidation to ferric oxide. This paper briefly outlines the mechanism of fuming and, on this basis, optimization of process parameters is discussed. Modelling analysis and recent industrial trials at Cominco show that coal entrainment in the slag, bath temperature, and bath depth are critical variables affecting process rate and efficiency. The first step in process optimization is to assess coal bypass of the bath. In general, changes which promote operation at a higher temperature, greater coal entrainment in the slag and extended residence time of the coal in the bath increase fuming performance. Coal entrainment is controlled by injection conditions whereas bath temperature is a function of coal combustion and ferrous oxide oxidation. Residence time of the coal is largely a function of bath depth. The implication of model predictions for continuous fuming is shown.

Jan 1, 1994

By Selim Coskun

In this study, tungsten matrix composites reinforced with 2 wt% TiC particles were mechanically alloyed (MA?d) for 3h, 6h, 12h and 24h. 1 wt% Ni is used as sintering aid which is added before and after mechanical alloying. Microstructural and phase characterizations of composite powders and sintered samples were carried out via SEM and XRD analyses. Furthermore, density and hardness measurements of as-consolidated and sintered samples were carried out. Additionally, DSC experiments were conducted to investigate the sintering behavior of the MA?d powders.

Jan 1, 2009

By Guoqiang Lv, Xi Yang, Wenhui Ma

Cast multicrystalline silicon ingots are widely used in photovoltaic manufacturing. A key issue to achieve high solar cell efficiencies is to attain an optimized temperature field during directional solidification (DS) process. This paper reports numerical investigation of multicrystalline silicon (mc-Si) ingot production using two major types of DS furnace. Specific examination is made on thermal distribution, interface shape and stress field. Evaluation is performed for the applicability of thermal system design to reduce thermal stress, improve crystal quality and enhance energy efficiency. The effects of procedure parameters and geometric configuration on temperature distribution are discussed as well to provide the viable solutions for systems optimization.

Jan 1, 2015

By G. C. Yao

Branch and needle-shaped intermetallic compounds of iron, silicon and aluminum normally exist in the molten aluminum. If a suitable amount of manganese metal is added into molten aluminum, the shape of the intermallic compound particles may become lumpish and spherical. According to the difference in electric and magnetic properties of these impurity particles and molten aluminum, these impurity intermetallic compound particles can be separated by applying an alternating magnetic field. In this experiment the alternating magnetic field was formed by a "c" type loop with AC (50Hz) current. The inner vacuum of the fireclay refractory separator is 25xl5xl30mm3 with a lateral baffle inside. The separator was put into the interspace of the "c" type loop. It was found that the longer the separation time, the larger the amount transferred of impurities. The amount of transferred impurities increases with the increase of separation time and intensity of magnetic field. The addition of manganese metal enhances significantly the efficiency of impurity separation

Jan 1, 2003

By Bruce H. Baker

Studies of used or unused refractory materials are excellent examples of applied mineralogy in industry. Refractory materials are mineral substances containing ceramic or chemical bonding systems. Knowledge of the mineral composition, bonding, and textural relationships often explains the resulting physical property values of a refractory and contributes to the interpretation of refractory wear mechanisms occurring in steel plant service.

Jan 1, 1982

By A. Mezei

A process has been developed to recover cobalt, gold and bismuth from the NICO deposit in Canada. The process consists of a bulk rougher flotation followed by an optional separation by flotation to produce a bismuth concentrate and a cobalt concentrate, grading on average 12.8 % Bi and 1.8% Co, respectively. Cobalt is leached by pressure oxidation at 97% efficiency, producing a pregnant solution suitable for further processing. Before optimization, about 38% of the bismuth is recovered in the selective concentrate, wherefrom it is recovered by ferric chloride leaching followed by cementation, at overall efficiencies exceeding 98%. The gold is recovered from the cobalt and bismuth leach residues by cyanidation, at 95% efficiency. Previous work described the results of the leaching of the concentrates, recovery of gold (Part I) and the recovery of bismuth (Part 11). This work describes the results of the cobalt recovery testwork and the resulting conceptual flowsheet. The sulfur dioxide-oxygen system was the most efficient for the oxidationlprecipitation of iron and arsenic from cobalt bearing pregnant leach solutions, producing purified solutions assaying <1 mg/L As and <8 mg/L Fe. The efficiency of cobalt solvent extraction (from the resulting purified PLS containing about 1 g/L Co) ranged from 9 1 to 98%; the co-extractions ranged from 88 to 100% for copper, from 28 to 33% for magnesium, from 6 to 7% for calcium and from 96 to 98% for zinc. Sulphide precipitation processes (using either sulfur dioxidelelemental sulfur or sodium sulfide) produced residual copper concentrations in the cobalt strip solution ranging from 0.1 to 2 mg/L Cu. About 90% of the calcium and magnesium were separated by scrubbing the organic with cobalt sulfate, producing residual concentrations of 12 mg/L Ca and from 180 to 330 mg/L Mg in typical feed solutions directed to cobalt carbonate precipitation tests. Cobalt carbonate precipitation efficiencies ranged from 75 to 78% when calcium and magnesium co- precipitations were restricted from 8 to 17% and 0.3 to 0.4%, respectively. The limits required by most stringent specifications on commercial grade cobalt carbonate products were met or exceeded.

Jan 1, 2002

By Boxun Lu, Juan Wei, Kun Chen, Wanlin Wang, Lejun Zhou

"Slag system is an indispensable part during the continuous casting process, and playing various important roles like absorbing inclusions, modifying heat transfer rate, preventing oxidation of molten steel, etc. to ensure the smooth process and excellent slab quality. However most slags contains more than 8% fluorides which tend to introduce a series of environmental and health problems. This study involves the research of the removal of fluorine through the chemical composition optimization. Through the studies of CCT, DHTT, XRD and SEM, it has been successfully founded that the crystalline phase of Ca11Si4B2O22 discovered in this study shows very similar crystallization property as Cuspidine (Ca4Si2O7F2), which is the most important crystalline phase in the current fluorine bearing slags. Moreover, the optimized free/low fluorine slag shows the opportunity to replace conventional high-fluorine mold slag for casting medium carbon steels that is regarded as the bottleneck of green slag development for continuous casting.IntroductionMold flux has been widely used in continuous casting to control heat transfer, lubricate the strand, absorb inclusions, provide insulation and prevent oxidation of the molten steel[1-3]. It usually contains fluorides, like CaF2, NaF etc., which are used to control the viscosity and solidification temperature of mold fluxes [4-5]. However, the presence of fluoride leads to corrosion of equipment, serious environmental pollution (toxic volatiles and water pollution), and high processing cost of cooling water[6-7]. Therefore, the study of low or free fluorine mold flux is of interest and attracts worldwide attention.S. Y. Choi et al. [4] used B2O3 as a substitute for cuspidine in steel B2PB2) however, B2O3 content was extremely high (up to 30 w%). Other studies have investigated F-free mold flux by adding or optimizing components as MgO, Li2O, B2O3 et al[8-11]. However, most of these focused on the melting and viscosity issues or for low or ultra-low carbon steels, where crystallization tendency is not significantly strong. Very few studies regarding to the development of low/free Fluorine mold flux for casting medium carbon (MC) steels have been conducted, due to the difficulty of the crystallization and heat transfer control without the formation of cuspidine."

Jan 1, 2014