Search Documents

By Xinghui Meng

The leaching behavior of platinum powder in .iodide solutions under oxygen pressure in an autoclave was investigated. Ammonium salts were added to the leaching solution at neutral pH as a key lixiviant for platinum. The effect of temperature, partial pressure of oxygen, concentration of iodide and of arttmonium salts on the dissolution rate of platinum was examined. Under experimental conditions, the leaching behavior of platinum powder exhibited a complex reaction mechanism. A precipitate was found during the leaching process and was identified to be platinum ammine iodide, Pt(NH3hI4. The dissolution rate was controlled by a series of chemical reactions, the equilibrium concentration of the platinum ammine iodide being responsible for the ultimate limit to the recovery.

Jan 1, 1996

By Jose R. Parga

In mining operations, cyanidation is the ,predominant method by which gold and silver are recovered from their ores and it is recognized that cyanide consumption can be a major factor that contributes to the operating costs for such operations. Also after extraction and recovery of precious metals a certain amount of cyanide is delivered to the tailings pond and must be considered with respect is environmental problems due to the toxicity of cyanides. In this regard, the Air-Sparged Hydrocyclone (ASH) has been used as a reactor for the treatment of cyanide solutions in two ways; first for cyanide recovery by acidulation using the Mexican modification of the Mills-Crowe process and second for cyanide destruction by oxidation with the use of chlorine dioxide (ClO2). In both cases, excellent performance can be achieved using the high capacity ASH system.

Jan 1, 1998

By Keiji Okumura, Jiayi Shan, Jian Yang, Masamichi Sano

"A new method of deoxidation and desulfurization of molten iron with magnesium vapor has been developed. An immersion tube, which was filled with pellets of the mixture of magnesia and carbon powders, was put into the molten iron. Magnesium vapor produced by carbothermic reduction of magnesia inside the tube was injected directly into the molten iron with argon carrier gas. The effects of temperature and carrier gas flow rate on deoxidation and desulfurization were investigated. A mathematical model of the reactions was developed. The rates of deoxidation and desulfurization were controlled by mass transfers of magnesium vapor in the gas-phase and oxygen and sulfur in the liquid-phase. This method may offer high efficiency for magnesium deoxidation and desulfurization of molten iron.IntroductionMagnesium is a strong refining agent in steel-making processes1 • At steelmaking temperatures, magnesium has a very low solubility in liquid iron, and a very high vapour pressure2 • Deoxidation and desulfurization with magnesium take place essentially through the interaction of magnesium vapor with oxygen and sulfur dissolved in molten iron, and magnesium can change chemical composition of nonmetallic inclusions3 • However, addition of magnesium to the steel bath is dangerous and does not give high efficiency in the refining process4 • Furthermore, as a refining agent, the price of magnesium is higher than aluminium and CaO fluxes. In the present study, a new method of the deoxidation and desulfurization of molten iron was developed using magnesium vapour in-situ produced by carbothermic reduction of magnesium oxide. Pellets made of mixture of magnesia and carbon powders were charged into an immersion tube, which was made of alumina or graphite. The magnesium vapor was injected directly into the melt. The effects of pellet mass, experimental temperature and carrier gas flow rate were studied on the refining rate. A mathematical model of the refining reaction was proposed on the basis of the experimental results."

Jan 1, 2000

By Andreas Siegmund

During the decade of the nineties the conventional method of primary lead smelting (sinter machine/blast furnace) was successfully challenged by the introduction of novel direct and continuous smelting processes. In combination with a significant shift in market structure, as well as more stringent government regulations these modem technological innovations like the QSL, Kivcet, and Isa/Ausmelt processes became more than major competitors. They have proven to be economically and environmentally viable. The intensification of the metallurgical reaction by applying oxygen enriched or pure oxygen bath or flash smelting principles resulted in cost savings and a higher flexibility with respect to raw materials and additives usage. By synchronizing individual auxiliary plant sections with the smelting process a virtually waste-free production and low-emission mode of operation with nearly optimum energy exploitation is achieved. The primary lead industry will gradually substitute the sinter -blast furnace operation with novel high-energy efficient technologies in the new millennium.

Jan 1, 2003

By Donald P. Ziegler, James F. Klausner, Srinivas S. Garimella

"By 2015, nearly half the world's population will live in ""water stressed"" areas. Production of fresh water utilizing waste heat from industrial processes has been identified globally as a research priority.About 15% of the electricity required to produce aluminum is lost as waste heat in the off-gas. However, the low temperature (low grade) of the heat limits reuse. The off-gases contain 50-150 ppm SO2 ; tightening regulations coupled with increasing coke sulfur levels are motivating SO2 control, for which seawater scrubbing is attractive for smelters with suitable access.We describe a process that produces fresh water, utilizing the waste heat while scrubbing SO2 . It uses direct contact between seawater and off-gas to humidify the off-gas. The vapor is subsequently condensed. In smelter trials, a unit treating a slip stream produced high quality water in the anticipated quantity, attaining over 95% SO2 scrubbing. Future work involves scaling the process to be economically attractive.BackgroundPopulation growth, coupled with industrialization and urbanization, are increasing demand for water. Water scarcity already affects every continent. Around 1.2 billion people, or almost one-fifth of the world's population, live in areas of water scarcity, and 500 million people are approaching this situation. By 2025, 1.8 billion people will be living in countries or regions with absolute water scarcity, and two-thirds of the world's population could be living under water stressed conditions (< 1,700 m3 per person annually) [1]. An assessment by the U.S. General Accounting Office revealed that under normal conditions, by 2013, water managers in 36 states in the USA anticipate water shortages, and that the number might grow to 46 states under drought conditions [2].The obvious choice to alleviate water scarcity is the 97% of available water in the oceans, which is saline and requires desalination for use in biological, agricultural and industrial applications. Technologies developed for desalination include Thermal Distillation, Reverse Osmosis (RO), Electro-Dialysis, and Vacuum Freezing. Distillation and RO are the most commercially prominent. Thermal distillation technologies include Multiple Effect Distillation (MED) and Multi-Stage Flashing (MSF). The report commissioned by the World Bank [3] is one of the many excellent references on desalination technologies. According to the International Desalination Association working paper [4], there were more than 17,348 industrial scale desalination plants installed or contracted by 2004. The total production from these plants is on the order of 8.3 billion imperial gallons per day. RO provides 47.2% of the total capacity. The leading thermal process, MSF, provides 36.5% of the total capacity. Although MSF and RO technologies currently provide the most cost effective means for desalination, their drawback is that they are very energy intensive, and whether or not they remain cost effective strongly depends on energy prices and energy supply."

Jan 1, 2012

By A. P. Pavia

Investigation on profitable ways to recover significant quantities of silver remaining dissolved in highly concentrated chloride solutions frequently pass through the development of solvent extraction (SX) routes. In this work, the general pathways involving Ag(I) extraction by dibutylthiourea (DBT) or tetraethylthiuram disulfide (disulfiram, DSF), from concentrated acidic chloride solutions, are investigated. With this purpose, the dependence of Ag(I) distribution coefficient on ligand and chloride concentrations has been analysed. Furthermore, in order to check whether there is some protonation at any site of DBT or DSF after contact with adequate chloride phases, lH NMR has also been used. The collected spectroscopic data suggest that anionic Ag(I) extraction reactions are not likely to occur. Based on the overall results achieved, proposals for the most probable Ag(I) extraction reactions are made.

Jan 1, 2001

By G. Upadhya

Of late, solidification modeling has progressed considerably to emerge as a viable simulation tool for the foundry engineer. A wide variety of tools exist in the commercial market to cater to the various needs of the design/ foundry engineer. In fact, recent developments in the area of solidification modeling have been so rapid that a comprehensive review of the state-of-the-art is very much needed. In this paper, an attempt is made to summarize the various issues of solidification modeling, at the same time addressing the historical evolution of the subject. The various phenomenological issues covered in this paper include: heat transfer, fluid flow during mold-filling, solidification kinetics and microstructural evolution, quick-analysis schemes for approximations, porosity prediction models, and the phenomena of fluid flow in the mushy zone. Modeling issues related to the development of solidification stresses which lead to defects such as hot tears and the development of artificial intelligence concepts in the area of rigging design are also discussed. Due emphasis is given to the various phenomena which add to the complexity of the whole subject, and the various alternatives available for solving a particular problem. For example, the heat transfer problem can be approached by the use of simple modulus schemes or by solving the conduction equation to obtain a more accurate temperature distribution. Similarly the microstructural evolution can be handled in a deterministic way by use of nucleation and growth models, or in a probabilistic way by use of empirical models. The main goal of this paper is to put the multi-faceted problem of solidification modeling in proper perspective so that it can serve as a guide for future developments in this area.

Jan 1, 1994

By J. Kevin Cotchen

The results of "submerged arc" electric furnace processing of a variety of materials is discussed with respect to the process and products, including the characteristics of the products (e.g. TCLP or Toxicity Characteristics Leaching Procedure). The materials melted include slags and wastes containing various metal oxides including copper, tin, lead, zinc, chrome, nickel and other associated elements. The findings of these tests are compared to those reported in the literature for other operations treating similar "wastes".

Jan 1, 1992

By Jianxin Zhang

A process, in which arsenic in the residue is transformed directly into scorodite and copper dissolves into the solution simultaneously, was studied. The process was carried out in acidic ferrous sulfate solution under oxygen pressure. The optimum conditions of the process were determined as follows: the initial H2SO4 concentration of 10 g/L; liquid/solid ratio of 10; Fe/As molar ratio in the feedstock of 1; the addition of calcium lignosulphonate was 1% of sludge; oxygen pressure, temperature and reaction time were 1.5 MPa, 150 °C and 6 h, respectively. Under these conditions, arsenic transformed to crystalline scorodite in size of 5–10 μm, and the transformation efficiency reached 97.60%; meanwhile, the copper was leached with a high efficiency of 93.34%. The stability of the leaching residue was evaluated by TCLP testing, and the results indicated the concentration of arsenic in the leaching solution was extremely low as 0.04 mg/L and met the standard of safe stockpile.

By Patricio Ruz, Gabriel Riveros, Carolina Ramirez, Andrzej Warczok, Rober Treimer

"Continuous converting of copper matte produces slag with high cuprous oxide content. The corrosion of chrome-magnesite refractories with slag of high cuprous oxide content is a major problem. Properties of olivine type of slag make the slag very attractive for matte smelting and converting.Analysis of phenomena determining the slag infiltration into the porosity of a refractory and dissolution of refractory components in the slag allowed for better understanding of the mechanisms of refractory destruction.The results of laboratory scale tests of the olivine slag infiltration into open porosity and corrosion showed dominating effects of slag temperature and cuprous oxide content. The optical and X-ray examination of slag samples permitted the definition of the mechanism of formation of new phases and refractory deterioration. 71"

Jan 1, 2009

By Nural Kuyucak

Acid mine drainage (AMD) occurs at operating and abandoned mine sites as a result of oxidation of sulphide minerals, and is characterized by low pH and heavy metal contamination (e.g. Fe, Zn, Cu, Cd, Al, Mn). It usually requires treatment before release in order to meet regulatory requirements. Chemical methods, such as lime neutralization and sulphide precipitation, are commonly used to treat AMD. However, the conventional processes require high capital and operating costs, and constant attention for many years into the future. In addition, the amount of sludge produced by conventional lime treatment processes poses an increasingly significant disposal problems at decommissioned mining operations. There is, therefore, an urgent need to develop passive, cost-effective processes for mitigating AMD and seepages originating from tailings and waste rock areas. Noranda Technology Centre (NTC) has been evaluating various methods being developed by other institutions, and exploring new ideas, to achieve passive in situ processes for treating AMD. These methods include anoxic limestone (ALS), lime-organic mixture (LOM), biosorbents (BIOS) and biotrench (BT). Current investigations at NTC involve preliminary bench-scale testing. Based on the outcome of the bench tests, a field test will be performed at a selected site. Details of the bench tests are discussed in the paper. Key Words: Acid mine drainage, treatment, metals removal, passive treatment, anoxic lime, limestone, biological treatment, sulphate reducing bacteria, biosorption, biosorbent

Jan 1, 1993

By M. M. Swan

A stratiform gold occurrence of Precambrian age located 20 miles southeast of Prescott, Arizona, within the Agua Fria Mining District, displays chemical, mineralogical, structural and lithological patterns indicative of a distal, exhalative volcanogenic environment. Metavolcanic and metasedimentary rocks of the Proterozoic Yavapai Series (1775-1820 m.y.) host the mineralization and are&apos;characterized by greenschist grade metamorphism, steeply-plunging penetrative folds and steeply-dipping schistosity. Mineralization is confined to a 100m thick stratigraphic section that is comprised of a series of thin auriferous massive sulfide beds and intercalated schist .containing disseminated sulfides. The mineralization extends more than 4km along strike. Coincident with, and largely confined to the mineralized strata, are anomalous amounts of As, Sb, Cu, Pb, Zn and Ag and associated silicification, sericitization and carbonatization. This exhalative mineralized system is interpreted to have been deposited in a paleo topographic low on the distal flank of a submarine rhyolite dome and to represent the final episode of a Precambrian volcanic cycle.

Jan 1, 1981

By Peter K. Everett

One of the major driving forces behind the development of the Intec Copper Process has been the increasingly stringent regulations governing SO2 emissions and, in some parts of the world, a declining H2SO4 market. Other incentives include operating cost (9.2 US c/lb Cu), capital cost (US $1400/annual tonne Cu compared with smelter cost of US$3-4000/annual tonne Cu) and the ability to treat low grade and contaminated concentrates. With such advantageous features, widespread use of the process is expected over time, leading to the production of large amounts of residues containing around 25% elemental sulfur, together with approximately 50-60 % akaganeite (FeOOH) and the ganggue minerals originally present in the concentrate feed. This paper briefly describes the Intec process chemistry involved in the formation of elemental sulfur, thereby avoiding atmospheric sulfur dioxide pollution, and the investigations to be carried out either to extract it or to turn the residue into a valuable by-product while minimising any adverse environmental effects, The process is being developed jointly by a group of fifteen major international mining companies.

Jan 1, 1996

By Hiroyuki Sano

A closed recycling process for the low-grade scrap of Al-based composite materials was developed. In this process flux treatment with water-soluble halide is a key technique. In the present work, flux treatment conditions were discussed from the viewpoint of the separation and the recovery of the base material, reinforcement and flux. Optimum separation condition was obtained for the NaCl-KCI-KF flux treatment. The recovered aluminum alloy can be recycled for various usages. The recovered SiC particles cannot be reused as reinforcement because of the coexistence of the contamination, therefore it is necessary to eliminate these contaminates or to find another use. The recovered flux is reusable with supplemental addition of fluoride.

Jan 1, 2003

By Hu Long

Pyrite, as the host mineral in refractory gold ores and concentrates, has been treated by pressure oxidation in sulfuric acid solutions at temperatures above 180°C to liberate gold prior to cyanidation since the 1980&apos;s. However, no data is available on the kinetics of pyrite during acid pressure oxidation over the temperature range of 180 to 230°C which is the range employed by most commercial plants. The dissolution of pyrite (FeS,) in sulfuric acid solution under oxygen pressure was investigated at temperatures ranging from 170 to 230°C. The effects of temperature, particle size, agitation speed, oxygen partial pressure, and pulp density were evaluated. The effects of foreign ion addition and the concentration of sulfuric acid were also examined. The apparent activation energy was estimated to be 42.6 kJ/mol in the temperature range 170 to 230°C. The reaction orders with respect to particle size and oxygen partial pressure were found to be -1.5 and 0.5 at 210°C, respectively. Experimental evidence suggests that the kinetics are limited by the surface chemical reaction initially, and then also to some extent by the diffusion of ferrous ions away from the particle surface.

Jan 1, 1999

By Sharif Jahanshahi

Calcium ferrite slags are often associated with Professor Yazawa due to his pioneering work on the thermodynamics of this type of melts. Over the past years CSIRO has invested some effort in studying physico-chemical properties of such melts to fill in some gaps in our knowledge and explore opportunities for application of the understanding developed. These investigations cover thermodynamics, transport properties of calcium ferrite based slags, as well as the kinetics of reactions of such slags with refractories. The present paper provides an overview of some of these studies and highlights some of the interesting behavior of such melts. The oxidation state of copper and arsenic in calcium ferrite based slags are predominantly Cu+ and As3+, respectively, at oxygen potentials below 10.1 atm. The concentration ofCu2+ in such slags becomes significant at oxygen potentials of greater than 10&apos;1 atm at 1300 ?C. The activities of CuOo.s and AsOl.S in calcium ferrite slags show strong deviations from the Raoultian Law, while that of CoO is very close to ideal behaviour with respect to pure solid CoO. Addition of Si02 to calcium ferrite slags can have significant effects on the activities of FeO and Fe2O3 and hence the stability of magnetite phase. Transfer of oxygen in calcium ferrite slags is fast with diffusivity of 2xlO?3 cm2/s at 1350 °C and activation energy of 16 kcal/mol Presence of solid phases, such as magnetite, has pronounced effect on the viscosity of calcium ferrite slags. The observed dependence on solid loading and shear rate indicates deviation from Newtonian behaviour. The interfacial tension between copper mattes and calcium ferrite slags is strongly dependent on the matte grade, with the determined values being much lower than the corresponding ones for interfacial tension between similar mattes and iron silicate slags. MgO, Cr2O3 and MgCr2O4 have low solubility in calcium ferrite slags and their solubility increases with increasing copper oxide content of the slag at 1300 °c. The oxidation state of the slag has strong effects on phase transformation, dissolution rate and disintegration of refractories in calcium ferrite slags. Other key factors with major impact on slag-refractory interactions include viscosity and surface tension of slags as well as the contact angle between slag and refractory material.

Jan 1, 2003

By J. B. W. Bailey

The Noranda Horne smelter in Quebec, Canada has change considerably during the last two decades to accommodate varying custom concentrate receipts, closure of the Horne mine, better working conditions, environmental programmes, new technology and increased energy and labour costs. This paper highlights the reasons for changing the smelter from two calcine charged and one wet charge reverberatory furnaces fired by coal to a smelter using. tonnage oxygen oil, natural gas and coal in a single wet charged reverberatory furnace and a Noranda Process continuous Reactor. The current operation 1 described, including three major topics; the use of oxygen/fuel burners on the charge banks of the reverberatory furnace which has increase the smelting rate from 680 to 1100 tonnes of concentrate per day; the oxygen enrichment of the Noranda Process converting air to achieve smelting rates of over 1800 tonnes of concentrate per day; the converting of the mixture of 73 percent copper matte produced from the Noranda Process and the 33 percent copper matte produced from the reverberatory furnace.

Jan 1, 1983

By Dimitrios Fillippou

Magnesium hydroxide is used in a number of industrial applications, from the neutralisation of acid effluents to the production of pharmaceuticals. High-quality magnesium hydroxide powders can be produced by hydrating slow-reacting magnesia in dilute magnesium acetate solutions. The process of magnesia hydration shows many similarities with a typical hydrometallurgical leaching operation; however, its kinetics are crucial not only for process design and control, but also for the production of powders with a desirable particle morphology. This article shows the results of an experimental work whereby industrial heavily-burned magnesia powders were hydrated in 0.01 to 0.1 mol/L magnesium acetate solutions at temperatures ranging between 333 and 363 K. Examination of the magnesium hydroxide produced and the analysis of the kinetic data suggest that the hydration of heavily-burned magnesia in magnesium acetate solutions is a dissolution-precipitation process controlled by the dissolution of magnesia particles. The activation energy was estimated to be 60 kJ/mol, while the reaction order with respect to magnesium acetate concentration was found to be about one.

Jan 1, 1999

By Dale T. Peters

Conductivity, both electrical and thermal, are attributes accounting for about 70% of the applications of copper and its alloys. This paper presents results of on-going research into two new applications that depend on copper&apos;s excellent conductivity. The Copper Development Association (CDA), together with materials and motor company partners, is working toward a solution to the key problem preventing pressure die casting copper for the conductor bar/end ring structure of the induction motor rotor, i.e., lack of a durable high-temperature mold material. Work is showing that a combination of high- temperature materials and elevated temperature processing gives much improved mold life compared to die steels. Substitution of copper for aluminum in the rotor can result in a 20% decrease in electrical losses in motors consuming 35% of electrical power generated in the U.S. The second development uses the excellent thermal conductivity of several high-strength high-copper alloys to simultaneously improve productivity and part quality in the injection molding of plastic parts.

Jan 1, 1999

By S. Z. El-Tawil, K. A. El-Barawy, M. B. Morsi, M. M. Nasr, Z. I. Zaki

"Tue sulphatization of zinc concentrate produced from heated zinc concentrate of Um Ghieg area, eastern desert by ammonium sulphate as sulphatizing agent is carried out at different conditions to achieve the appreciable formation of soluble sulphates. The maximum zinc recovery as soluble sulphate equfils to 95% upon using 1.5 stoichiometry ammonium sulphate at 600 °C for one hour. Tue obtained leached zinc sulphate solution is subjected· to purification process to prepare high pure zinc metal and zmc compounds such as pure zinc sulphate, zinc caibonate and zinc oxide. The products obtained are analyzed chemically and identified by X-ray analysisTue mechanism and kinetics of the sulphatization process of zinc concentrate are considered where the activation energy is calculated and equals to 33.3 K.J.mol""1 A process flowsheet for the overall sulphatization process of zinc concentrate by ammonium sulphate is proposed.IntroductionConsiderable reserves of zinc ores are present in Um Ghieg area eastern desert, Egypt. The possibility of extraction zinc from these ores and preparing its valuable compounds by choosing a more feasible technology become of vital importance. An attention is focused on the sulphatizing roasting processes (1-9) to achieve the appreciable formation of soluble sulphates. Previous publications are reported in our division by El. Tawil and others (10-16) using ammonium sulphate as sulphatizing agent for the successful treatment of nonferrous bearing materials.Therefore, the present work aims to study the different factors affecting the sulphatizing roasting process of local zinc coocentrate by anunonium sulphate to extract completely zinc and preparing its main compounds. Tue mechanism and kinetics of the different chemical reactloos that 1ake place in the process are considered."

Jan 1, 2000