Search Documents

By Clifford J. Roblee

In this paper, various seismic indicators are evaluated for ability to discern fractures induced into a rock mass by blasting. This is accomplished by presenting results from in situ crosshole seismic studies performed prior to and after a sequence of controlled blasts within limestone and dolomite rock near Austin, TX. Indicators investigated are compression (P-) and shear (S-) wave travel times, first peak and maximum amplitudes, first arrival rise rate, and the linear spectrum of the received signal. Compression wave travel time yielded the most consistent results, while the various amplitude indicators yielded the poorest results for the equipment configuration utilized. In addition, this study documents magnitudes of change in seismic measurements which occurred following blasting. Both P- and S-wave travel times exhibited a wide range of variation due to blasting. Near blast centers below the surficial fractured rock, velocity decreases of about 10% were noted, significantly less than the 50% decrease observed for previously fractured near-surface rock through which the explosive energy was vented. Signal amplitude measurements also varied in magnitude but were less consistent.

Jan 1, 1989

By Duk-Won Park

The excavation of a longwall panel causes a continuous stress redistribution in the surrounding strata for every face advancement. The understanding of the behavior of rock to high level of stresses is instrumental to the structural design of underground mines. In order to achieve a realistic analysis of the behavior of strata, the three-dimensional finite element method is frequently used. Also the model developed for the analysis has to be designed large enough to represent the influenced strata in the study area and a sufficient number of elements has to be used to provide detailed information on the stresses and displacements. Due to the size of the model and its numerical solution the CRAY X-MP/24 supercomputer has been used for this study. The mine site selected for the analysis is a coal mine located in the Black Warrior Basin in Alabama. The mine has two longwall sections at a depth of 2,000 feet with various dimensions of chain pillars, including yield pillars. Various research programs at this mine have been carried out by Park et. al. ( 1984 ). Therefore data were already available on the geology, and physical properties of rock and coal. In addition a rock testing program has been carried out to obtain rock mass classification parameters. The progressive failure technique has been utilized to simulate stress redistributions. The failure criterion after Hoek and Brown ( 1980 ) which is based on rock mass behavior was used for the iterative technique. Simulated stress redistributions are therefore very realistic. In order to automate the process involved in the application of progressive failure technique, a computer program has been developed. The combination of a large scale three-dimensional finite element model and the automation of progressive failure simulation provided a tool that can generate a large amount of information related to the behavior of rock and coal as a response to a longwall mining operation.

Jan 1, 1989

By Ernest A. Curth

An estimated 49 billion tons or 29 percent, of the coal reserve base to a depth of 1,000 feet in the eastern United States fall in the 28- to 42-inch range. Often left out as a consequence of selective mining, it is a paramarginal source that will become increasingly important. At present, all active thin seam longwalls are located in the Eastern Coal Province, and a number of operations have been suspended due to the erosion of the market for metallurgical coal. Extensive premining studies, appropriate mine planning, reliable equipment that is designed with ergonomics in mind, adequate roof support, intensive training, and strong face discipline are the ingredients that provided a measure of consistency in production for the last 10 to 16 years, particularly in the Pennsylvania bituminous coalfield where single drum shearers dominate. Plows, which were found to be very productive in suitable strata in Europe, are used in the Pocahontas field. Low seam four- and six-legged shields have been introduced recently. The future holds automation at progressive levels. The first step is batch control with the benefits of quickly applied roof support and reduction of workmen exposure to environmental hazards.

Jan 1, 1981

By Hamid Maleki

A novel ground control program has been developed at Plateau Mining Company through five years of geotechnical investigations. The study was initiated to determine the causes for roof stability problems and to develop alternative support and monitoring systems for increased safety and productivity. From systematic roof fall observations, extensive geologic mapping, roof drilling and monitoring ground movements along gate entries of four longwall panels, a sand- stone channel system was detected and shown to impact roof stability. In particular, underlying mudstones up to seven feet thick experienced instability due to differential compaction and load transfer from the gob. Roof bolter operators were trained to report roof lithology for mapping channel positions into the roof and for selective use of longer bolts. This boosted operator morale, and improved ground conditions. Monitoring rates of roof movement is used in these areas for detection of instability and for application of secondary support: This has significantly increased safety and productivity.

Jan 1, 1987

By D. A. Payne

Large excavations, such as Iongwall panels, result in extensive vertical stress redistribution in the surrounding strata. The large abutment stresses developed may produce damage to pre-existing or planned excavations in the same seam or in seams above and below the workings. Knowledge of the magnitude and location of these stresses is therefore important in the design of mine openings; pillar sizes for panel and pillar layouts, roof supports in longwall gateroads and workings over or above pre-existing or planned extraction in adjacent seams. In an attempt to reduce costs, the Cape Breton Development Corporation (CBDC), a Federal Crown Corporation responsible for operating two retreat longwall coal mines, examined the potential for either interpanel barrier pillar width reduction or entire pillar elimination by the adoption of dual life gateroads for the longwall panels. In order to assess the potential for reduced interpanel barrier widths or total elimination, an investigation of the redistribution of vertical stresses around longwall panels in the Sydney Coalfield was established. The study was conducted jointly by the Cape Breton Coal Research Laboratory (CBCRL), of CANMET (a division of Natural Resources Canada) and the Denver Research Center (DRC) of the United States Bureau of Mines. The program included monitoring of vertical stress changes around longwall panels and gateroad behaviour in two seams. USBM-style hydraulic borehole pressure cells connected to chart recorders for continuous monitoring were deployed at four sites, two at Lingan Colliery and two at Phalen Colliery. This report describes the investigations conducted at Phalen Colliery. Contoured plots of stress redistribution around two sites are presented.

Jan 1, 1995

By Dennis Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson's effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.

Jan 1, 2003

By Mao Bai

Mining in situations where there exists a potential hazard from inundation has always existed in coal mining, and often reserves were left unmined in favor of reserves with no such hazard. However, increased pressure on expanding the minable reserves and on producing low-sulfur coal, has made mining under water hazards necessary in many parts of the world. Recent joint efforts by the authors to develop case-history data bases of mining under water hazards has allowed the bringing together of Chinese and United States experience and guidelines for such mining. In China, mining under water hazards has been successfully accomplished for a number of years, allowing the development of a good data base from which to draw guidelines. In the United States, much more limited experience, and the longer delay in adopting longwall mining compared to the rest of the world, has forced reliance on a more limited data base and European experience. In the United States (and Canada), the data base is continuing to increase as more operations start-up. Developing a generally-applicable set of guidelines for international use, based upon extensive Chinese and other experience, appears feasible. The Chinese and United States experiences are detailed by case histories.

Jan 1, 1995

By Chris Mark

Pillar recovery continues to be a significant ground control hazard. During the past decade, 10 miners were killed during pillar extraction operations in southern West Virginia. Studies conducted during the past decade have identified a number of "risk factors" that can be used to evaluate pillar extraction plans: Cut sequence Final stump Timber or Mobile Roof Supports Roof bolting Intersection span Depth of cover Roof quality Age of workings For each of these factors, rock mechanics science suggests which alternative would be expected to be more risky. For example, numerical models were used to evaluate different cut sequences, and indicated that less roof convergence occurred with the outside lift method than with the Christmas tree in the particular environment simulated. For many of the risk factors, accident statistics confirm the science. One finding was that currently almost 70% of the retreat coal in southern WV is being mined with MRS. In contrast, timber supports were used in 70% of the past decade's pillaring fatalities. This paper discusses each of the risk factors in turn, presents the relevant accident statistics, and shows how the risk factors can be combined to estimate the overall hazard. It also addresses the use of pillar design to minimize the risk of global stability hazards including squeezes. massive collapses, and bumps.

Jan 1, 2002

By David J. Reddish

Longwall systems are inflexible in layout, intolerant of disruption and represent a substantial investment. It is therefore essential drat all understanding of the likely strata behaviour and support requirements is obtained prior to panel development. For many tears rock mechanics engineers have applied numerical modelling based kill finite element techniques to the design of the support and layout of underground excavations. Whilst such design methodology has worked well in civil engineering and hard rock situations, it has been less reliable when applied to excavation design in the soft rocks of the coal measures. This lack of reliability has been identified largely as being the result of the utilisation of unsatisfactory input data, This paper describes the results of an ongoing research programme at the University of Nottingham in which a novel rock mass rating system known as the UK Coal Mine Classification system was developed to enable the prediction of the strata properties that are required as input parameters for use in numerical modelling of the deformation of soft rocks around excavations such as roadways and longwall faces in coal mines. The paper describes the development of the system. the way in which classifications are applied to derive input data for numerical models and gives two case studies ill which deformations and stress re-distributions around coal mine excavations have been simulated by numerical modelling using the FLAC finite difference code.

Jan 1, 2000

By Eric R. Bauer

Skin failures of roof and rib in underground coal mines continue to be a significant safety hazard for mine workers. Skin failures do not usually involve failure of the support systems but result from rock or coal spalling from between the support elements. For instance in 1997, over 800 miners were injured by roof and rib falls, of which 98 pet were the result of skin failures. Also, nearly 80 pct of the roof and rib failure injuries occurred at or near the working faces in development sections. The face area is a zone where the potential for skin failure accidents and injuries and roof and rib failures, in general, is high because of mining activity, ground readjustment due to changing stress conditions, and the higher exposure of mine workers. In addition, failures occur where the roof and rib are unsupported. This paper features a review of the roof and rib accident statistics resulting from skin failure, highlighting the incidences by average days lost, in-mine location, state, MSHA District, and worker activity at the time of injury. A detailed analysis of recent fatalities caused by skin failure is included. Also discussed are the causes of roof and rib skin failures, current methods and support materials for skin surface control, as well as a historical literature review of skin failures and control methods.

Jan 1, 1999

By Salah Badr

Longwall mine layouts with their entries, chain pillars, face support systems, advancing mining faces and compacting gobs represent a geomechanically complex mining operation. Geomechanical aspects are further complicated if mining occurs at depths exceeding 350 m, as stresses induced adjacent to the excavations exceed the unconfined strength of the coal and result in fracturing of the sidewalls of entries and chain pillars during development. Traditional methods of geomechanical analysis, whether empirical or numerical, are unable to represent such behavior satisfactorily. Achieving some meaningful results requires explicit representation of the three-dimensional boundary conditions and implementation of appropriate constitutive models for the rock mass. This paper describes a numerical modeling methodology for deep longwall mines operation using the FLAC3D finite difference de, which incorporates a strain softening constitutive law for modeling failure of coal. An important aspect of the modeling method includes accounting for stress relief provided to the pillars and entries due to the increasing load applied to the compacting gob.

Jan 1, 2003

By Thomas Barczak

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water¬to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water¬solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

Jan 1, 2003

By Mario G. Karfakis

Mining related subsidence is a major concern over abandoned shallow coal mines. Many of the subsidence prone areas are presently used or will be used in the future for residential housing development. Concern over mine subsidence is inhibiting the development of surface land uses on previously mined area. This concern prompted public officials to realize the need to develop guidelines which can be used to assess and reduce the risk of mine subsidence damage to building and other improvements. Subsidence and the associated ground movements must be defined before one can relate them to building damage. Surface movements resulting from underground coal mining occurs in two phases termed as: active subsidence and residual subsidence. Active subsidence refers to all surface movements occur in^ simultaneously with the mining operations, while residual subsidence is-that part of the surface deformation which occurs following the cessation of mining. Residual subsidence is the major concern over abandoned mine lands. The duration of residual subsidence is of particular importance from the standpoint of damage at the surface to structures built after the mine has been abandoned. Time spans during which surface subsidence may occur, vary markedly with the mining method being used. In total extraction methods, such as longwalls, subsidence is induced rapidly, beginning almost immediately after mining. Subsidence concurrent with coal extraction is desirable for a safe longwall mining operation. Usually subsidence is complete within a relatively short time. The remaining settlement occurs as residual subsidence due to the gradual compaction of the subsided ground. The relative proportion of the residual subsidence movements is dependent upon the presence of remnant pillars and roadside packs. rate of face advance and depth of workings. In partial extraction methods, such as with room-and-pillar systems. major occurrences of surface subsidence may be delayed for decades until the support pillars and/or the roof have substantially deteriorated and collapsed. The actual time involved depends on a number of factors such as the strength of coal, roof, and floor, extent of fracturing. presence of water, depth of workings, pillar size and percentage extraction. Consequently residual subsidence is more likely to occur over abandoned room-and-pillar mines. The following sections define subsidence over abandoned mines, review the proposed mechanisms, identify the controlling factors and examine the prediction methods.

Jan 1, 1987

By M. O. Serbousek

In 1975 the Bureau of Mines Spokane Research Center began a series of laboratory and field tests to investigate the feasibility of developing a substitute for the organic chemicals used in resin roof-bolting systems. An inorganic system, comprised of calcinated gypsum, an accelerator, and microcapsules of water was developed and patented by the Bureau in 1977. The system has several advantages including economics, non- toxicity, nonallergenic, inflammability, and is not based on petroleum products. Two roof-bolting systems utilizing inorganic cements are under development at the Spokane Research Center--a cartridge system, using the microcapsules of water and accelerator, and a slurry system, using a mix-inject method which combines dry powder cement with water for simultaneous injection into a predrilled roof-bolt hole. Several underground field tests have been conducted in eastern coal mines. Test results indicate that inorganic cartridge systems are adequately supporting mine roof in several test sections. Economic potential for the bolt systems appears favorable.

Jan 1, 1981

By Craig Collins

The objective was to develop a Real Time Drilling Display System for Rotary Roof Bolting using Analyzing Software to display mapped holes as they are being drilled in real time. The Analyzing Software was developed to analyze and interpret drill sensor data produced during a rotary drilled roof bolt hole by using algorithms and drill sensor data trends to find and locate roof separations or voids. After this software was validated through lab and field testing, its application needed to be tested in a production environment. However, the current method used to record the drill sensor data proved to be cumbersome for the mine to use on a continuous production basis. With different more practical mediums being explored and considered, a Drilling Display System was developed that will both map holes in real time and record the data for later review. With the Analyzing Software's current level of accuracy and with the convenience offered by the real time Drilling Display, the Drill Display System was implemented along with a test mine's current roof control plan and tested as a roof separation "Early Warning System". After installing the Drilling Display System onto a machine, input and suggestions from the mine environment were considered and design changes were made. The real world application provided a design direction that made the information produced by the Analyzing Software both convenient and significant for the test mine. Also, using the Drilling Display System increased the number of drilled holes that were both mapped and recorded. The results from studying these recorded data files lead to refinements in the current algorithms used by the Analyzing Software which increased the overall accuracy and capability of the system A fairly accurate representation of void or separation locations in the mine roof can be determined fromsensor data recorded during production bolting cycle. The immediate feedback on the local roof condition that the Drilling Display System provides, amounts to a quicker and safer alternative to the scratch hole and the video bore-scope examinations that arc performed after the bolting is completed. This project has shown that making the alternative method of examining the roof condition practical for the mine to use is just as important as the accuracy of its results. Based on the results of this field test, this or other methods of reviewing the analyzed drill hole data will be explored.

Jan 1, 2004

By David Newman

Coal refuse impoundments and underground mines are frequently sited in close vertical and horizontal proximity in the valleys of the Southern Appalachian coalfield. The steep V-shaped valleys provide the volume necessary for slurry storage against a coarse refuse embankment that is constructed across the valley mouth. The presence of coal outcrops on the valley walls provides economic access to mineable coal seams that may be located under several thousand feet of overburden beneath the adjacent ridges. In some instances where the underground mine precedes the slurry impoundment, the type of mining (partial or complete extraction) and pillar centers were selected without consideration for the potential future use of the valley as an impounding structure. The high standard established for the design and stability analysis of the coarse refuse embankments is clearly illustrated by the absence of an embankment failure in the thirty-one years since Buffalo Creek. However, the recent Martin County slurry spill focused attention on a thorough geotechnical analysis to prevent a connection between the flowable slurry and the mine void. The overburden, roof, pillar, floor, and outcrop barrier stability are examined to quantify the break through potential. The strength and physical properties of the consolidated fine refuse are also important since this material is often the most well-defined and quantifiable barrier separating the slurry and mine void. Because each site is unique, the appropriate analysis ranges from the calculation of roof, pillar, and floor safety factors to detailed numerical modeling of the mine workings and the determination of ground deformation and strains resulting from mine subsidence. The method of refuse disposal may be altered to slurry cells where the accuracy of the mine maps, extent of mining, type of mining (development or retreat) cannot be reliably verified or the break through analysis does not produce an acceptable level of risk. Case histories from the Southern Appalachian coalfield are used to illustrate the application of methodologies to quantify the break through potential of coal refuse impoundments.

Jan 1, 2003

By Daniel W. H. Su

Surface subsidence induced by multiple-panel coal extraction was calculated with finite element stress analysis. The use of nonlinear material behavior and GAP elements, which provide a realistic representation of shearing along existing planes of weakness, allows the finite element program to accurately reproduce observed subsidence profiles. A reduction factor of 1/6 is applied to the measured rock strength and modulus for use in the finite element model. The models satisfactorily predict a significant change in maximum subsidence and subsidence profile associated with an increase from subcritical to near critical panel width. Modeled shearing along planes of weakness is in good agreement with available time domain reflectometry field observations and is demon¬strated to have a very profound effect on the maximum subsidence and the shape of the subsidence profile. When both material nonlinearity and planes of weakness are incorporated, the finite element model appears to possess great potential for accurately predicting surface subsidence and subsurface strata deformation in environments where little subsidence information is available.

Jan 1, 1990

By D. W. H. Su

This paper describes geomechanical criteria employed by Consol Energy for selecting mine-specific longwall face supports in the past decade. The criteria include immediate and main roof rock characteristics, floor rock characteristics, critical tip-to-face distance and shield operating range. Detailed roof rock properties from high-density core holes as well as in-mine scope holes are used to evaluate the set load density and shield stiffness required to control the immediate roof and the yield load density required to absorb the load density developed from main roof weighting. Detailed floor rock properties from core holes and in-mine floor bearing capacity tests are used to specify the maximum peak toe pressure as calculated by the Jackson method. The critical tip-to-face distance is evaluated based on the immediate roof rock strength, layering and thickness. The shield operating range is evaluated based on main bench thickness, the presence of thick draw slate, the potential of minor roof falls at the face and transportation restriction. Three case examples representing three different geologic conditions are presented to illustrate the successful application of these geomechanical criteria for selecting longwall face supports within Consol Energy in the past decade.

Jan 1, 2004

By Gexin Sun

This paper presents the physical modelling results of subsurface fracture development associated with longwall mining operations and an application of image processing techniques to interpretion of the results. Physical modelling results have been obtained by employing a large sand and plaster model loaded purely by gravity as a means of fracturing the subsurface strata above the longwall excavation. The results have shown fracture development and crack propagation as a longwall face advances and demonstrated that the strength of stratified rocks, the presence and position of a weak band-, and the extraction thickness, have significant effects upon the overall fracture patterns above the excavation. Binary images of fracture patterns were scanned from the black and white photographs of the tested models using an image analyser coupled to a video camera. These images were manipulated by a custom written C program which allows the images to be processed in both vertical and horizontal direction. The images were filtered to quantitatively differentiate between vertical and horizontal fracture intensities. The vertical fracture intensity is particularly important as vertical fractures are considered to provide the main avenues for surface and subsurface water inflow into the excavation. The use of the image analysis techniques has shown a promising improvement in image enhancement and in model results interpretation in a quantitative manner. The numerical nature of the image analysis results will allow further statistical comparison with other modelling techniques to be undertaken and significantly increase the scope for use of the modelling technique results.

Jan 1, 1992

By Jinsheng Chen

For underground openings, many factors can cause roof failure and thus roof falls. The most common factors related to Mother Nature are weak roof lithology, geological structures, and an abnormal in-situ stress field. Theoretically, any underground opening can be successfully supported under any geological and mining conditions if the opening width is limited and the roof supporting system is well designed. However, roof control cost must be taken into account. In practice, to minimize the roof control cost, different roof control plans have to be considered to take care of the uncertainty or variation in geological and mining conditions. For most underground mines, it is unsafe or economically unrealistic to use one fixed roof control plan for the entire mine. Therefore, local, abnormal geological and mining conditions must be identified and a site- or area-specific roof control plan must be employed. This study tries to identify the major factors that have significant impact on entry roof stability by analyzing the historical roof fall data at Rofomex mine. Finally, the appropriate roof control plans or roof bolting systems for different geological and mining conditions are recommended.

Jan 1, 2011