Search Documents

By J. P. Harrison, J. A. Hudson.

ABSTRACT: When considering the rock stress component of rock mechanics design, the basic procedure is to consider the pre-existing stress-state in the rock mass and then estimate the disturbance to this stress state as a result of engineering excavation. Failure criteria are applied to the final stress state to establish whether failure will occur. However, during the evolution of the stress state, the failure locus may be reached before the anticipated failure state and, in this case, failure will occur unexpectedly. This indicates that the complete stress path (defined as the variations in magnitudes and orientations of the stress tensor components resulting from engineering-induced or natural changes) must be considered. We list a set of stress path principles with their corollaries and then introduce a new and powerful method for simultaneously illustrating changes in the six independent components of the stress tensor. This method plots the magnitudes of the principal stresses above their orientational paths on the hemispherical projection, to provide a three-dimensional stress path locus for each of the three principal stress components. In connection with this presentational device, we illustrate a number of concepts associated with the stress path in rock engineering. For example, we show how the minor principal stress approaches zero at an unsupported excavation face, the interchange of the trajectories of two principal stresses when their magnitudes become equal, and the influence of the bounds on the principal stresses given by strength criteria. RESUME: Si on s’interesse à la composante “contrainte” lors d’un dimensionnement en mécanique des roches, la méthode de base consiste à considérer l’état de contrainte pré-existant dans le massif rocheux, puis d’estimer la perturbation à cet état générée par l’excavation projetée. Des critères de rupture sont appliqués à l’état de contrainte final pour établir si une rupture va se produire. Cependant, lors de l’évolution de l’état de contrainte, la surface critique peut être atteinte ce qui provoquera une rupture anticipée et, dans ce cas, cette dernière sera inattendue. Cela indique que le chemin de contrainte complet (défini par les variations de l’intensité et de l’orientation des composantes du tenseur des contraintes liées à des causes anthropiques ou naturelles) doit être pris en compte. Nous présentons un ensemble de règles pour les chemins de contraintes ainsi que leurs corollaires et, ensuite, nous introduisons une méthode, nouvelle et puissante, pour présenter simultannement les changements des six composantes du tenseur des contraintes. Cette méthode consiste à tracer l’intensité des contraintes principales sur le chemin d’orientation des contraintes à l’aide d’une projection hémisphérique afin d’obtenir le lieu, en trois dimensions, de chaque contrainte principale. En relation avec cet outil de représentation, nous illustrons certains concepts associés au chemin de contrainte en ingénierie au rocher. Par exemple, nous montrons comment la contrainte mineure tend vers zero à la surface d’une excavation sans soutenement, le changement de direction des deux contraintes principales quand leur intensité deviennent égales, et l’influence des conditions aux limites sur les contraintes fournies par un critère de rupture. ZUSAMMENFASSUNG: Bei ingenieurmassigen Taetigkeiten in Felsgesteinen ist es noetig die ungestoerten Gesteins Stress Componenten, die vor einem anthropogen Eingriff im Gestein vorhanden waren, zu kennen und erst dann Vorhersagen ueber Stoerung des Stress Zustandes, der durch einen ingenieurmaessigen Eingriff hervorgerufen wird, herzuleiten. Kriterien fuer das Versagen werden im letzten Stadium, des Stress Zustandes angewendet, um zu erfahren ob ein Versagen wohl eintreten wird. Es ist jedoch zu beachten, dass waehrend des Stress Aufbaus ein oertliches Versagen eintreten kann, welches vor dem eigentlichen, erwarteten Versagens Zustand auftritt. Diese Moeglichkeit weist darauf hin, dass der gesammte “Stress Path” (definiert durch die Variationen der Stress Tensor Komponenten in Richtung und Groesse, hervorgerufen durch ingenieurmaessig hervorgerufene oder natuerlich Vorgaenge) betrachtet werden muss. Wir fuehren eine Liste der “Stress Path” Prinzipien auf und stellen dann eine neue und wirksame Methode zur gleichzeitigen Darstellung der sechs unabhaegigen Komponenten des Stress Tensors vor. Diese Methode stellt die Groesse der “Principal Stresses” in Abhaengigkeit von ihrem rauemlichen Weg auf einer hemispherischen Projektion dar und erlaubt hiermit eine drei dimensionale Darstellung fuer jeden Ort des “Stress Path’s” in die drei Haupt Stress Komponenten. Im Zusammenhang mit der hier gegebenen Darstellungsart, verdeutlichen wir eine Reihe von Konzepten in der Felsmechanik. Wir zeigen zum Beispiel, wie der “Minor Principal Stress” Null zustrebt an einer Wand von einer nicht abgestuetzten Ausschachtung, den Austausch von Trajektorien zweier “Principal Stresses” wenn ihre Groessen sich gleichen, und den Einfluss der Groesse von “Principal Stresses” bei gegebenen Kriterien des Festgkeits Versagens.

Jan 1, 2003

By M. M. Hajdasinski

The internal rate of return (IRR) is one of the most popular project evaluation criteria in the mineral industry, as well as in other industrial sectors. Analysis of its assumptions reveals, however, that this criterion does not function in the way it is supposed to. The search for a new criterion that would reflect the true rate of return (TRR) of an investment project or the true borrowing rate (TBR) of a borrowing project has led to the development of several approaches, yielding, for the same project, generally different values of the interest rate in question. Two of those approaches have been selected as the most representative and practical. Each has been presented in two variants, and subsequently analysed. As a result, it is shown that the various approaches to the TRR/TBR are all consistent with the net present value (NPV) criterion, and that each can serve as an independent project evaluation instrument, provided its assumptions can be regarded in a given situation as realistic enough.

Jan 1, 1987

By J. -M. Chautru

A geostatistical simulation of a typical mining site for polymetallic nodules in the North Pacific Ocean is presented. This is the first stage in the design of an industrial mining system. Two variables which have a major effect on the orebody's economic potential are considered, namely: the maximum slope of the ground inside a mining block of 50 x 100 m; and the average quantity of nodules on the same support. Two geostatistical problems have emerged in this study. The first is due to the lack of a change of support model for the maximum of a variable. A provisional solution, considering an experimentally accessible 'equivalent' support, is proposed. The second is due to a non-linear link between the two variables. To be able to take this into account in the simulation, we propose a new method based on the decomposition: X = E(X/Y) + Residue (X). Satisfactory results were obtained with this approach.

Jan 1, 1987

By C. C. E. Pretorius, V. M. Mathoho, A. van Zyl, R. J. Mostert

The in-service degradation of the mechanical properties of steel components through the damage mechanism of high temperature hydrogen attack (HTHA), is a topic of concern in the refining and green hydrogen industry. This damage mechanism occurs in susceptible steels operating in environments at high temperatures and hydrogen pressures. The current investigation deals with the indirect monitoring of mechanical degradation via tracking of the swelling strain in affected structures. An autoclave with an AISI 316 shell was utilized to simulate accelerated HTHA damage at 550 °C and 46 bar for exposure times ranging from zero to 700 hours. The progress of the HTHA damage was tracked using encapsulated high-temperature strain gauges. The correlation between the swelling strain and mechanical property degradation was studied to develop a methodology for the continuous monitoring of embrittlement. The tensile sample orientation of the carbon steel plate was included as a variable, i.e., samples parallel, transverse, or perpendicular to the plate rolling direction were included, since it has been shown that the sample orientation influences the HTHA damage features. For the through-thickness orientation, and upon exceeding a threshold value of exposure time, all tensile properties were severely degraded, with values in the order of a 90 per cent reduction being observed. It was found that the degradation of carbon steel mechanical properties can be correlated to the swelling strain measured during exposure. The critical point for mechanical property degradation in the plate through-thickness orientation, whereafter a severe decrease in the ductility of the material occurs, was found to be in the order of 1% of the total swelling strain measured during exposure, equivalent to 65 microstrain. This threshold was found to be significantly lower than that expected from the literature, where limits of 400 to 1000 microstrain were postulated.

Nov 27, 2024

By R. B. Khumalo, F. K. Mulenga

Sampling in a continuous flotation plant is always a challenge as these plants are meant for production and not research work. The continuous flotation operation used in this work produced three sets of data: the first was based on overall plant performance, done by sampling the feed, concentrate, and tails; the second was based on the roughers row cell-by-cell; the third set of results came from the cleaners/recleaners row cell-by-cell. The highest recovery results in all sets of data obtained lie in the particle size ranges of 40 μm and 100 μm, which is in agreement with results by other researchers in the same field. King’s theoretical (model) recovery proved to be able to fit the experimental data but there is still room for improvement as the sum of squared error ranged between 400– 1200. Data obtained in continuous flotation operation could be used with batch flotation test-work to characterize scale-up of flotation cells.

Jan 1, 2023

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 µm. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By M. H. Moys

Accurate models of mill power are becoming more necessary as the design, operational, and control requirements for grinding mills become more stringent. Models of mill power are reviewed briefly, and a new semi-phenomenological model is derived. The conventional torque-arm model for mill power is combined with a model of the tendency of the load in a mill to centrifuge at high speeds, to describe mill power that can be related to several design variables (such as mil geometry, mill speed, and liner design) and control variables (such as load volume, slurry rheology, and mill speed in the case of variable-speed milling). The semiphenomenological nature of the model allows rational conclusions to be reached concerning the effect of various aspects of mill-load behaviour on mill power. The model is shown to be capable of describing reality with much greater accuracy than is achieved by empirical models such as the Bond model.

Jan 1, 1993

By J. C. D. Gush

Paper written on project work carried out in partial fulfilment of Laboratory-scale testwork was undertaken to recover oxidic copper-cobalt minerals by froth flotation, which requires maintaining a certain sulphide level in the pulp. To improve control of the sulphide concentration, an electronic closed-loop system was designed that responds to the potential output of an ion-selective electrode. The PID control was improved by adding a pre-emptive control and a self-calibration feature; a data logging facility is also included. An inexpensive valve design was incorporated using locally available parts. The operating results of this control design are presented.

Jan 1, 2005

By M. Frenzel, K. Bachmann, M. Rudolph, R. Tolosana-Delgado, E. Schach, M. Buchmann, L. Pereiraa, K. G. van den Boogaart, N. Kupka

Geometallurgy - the science of predicting the behaviour of ores along the value chain based on their geological and mineralogical characteristics - has barely moved beyond process minerology studies. These studies typically link process behaviour to the mineralogical and microstructural characteristics of pristine or processed ores in a qualitative or semi-quantitative manner. Eventually, a trial-and-error optimisation of the operation is achieved. However, to deliver on its promise, geometallurgy should progress beyond this current approach to a fully quantitative understanding of process behaviour, including the various uncertainties involved, namely predictive geometallurgy. One of the barriers currently hindering this development is the neglect of most ore characterisation data obtained in geometallurgical studies. This is mostly due to the large extent of this information exceeding the capacity of conventional software. To address this challenge, we developed a data mining platform consisting of an SQL database, an R front-end in-house package, and back-ends to interpret data from several analytical instruments. This platform enables the use of the statistical and data mining power of the R open-source environment for any geometallurgical study. Potential applications range from ore characterisation to process understanding and forecasting, and from geostatistical prediction to operational control and optimisation. The scripting abilities of R allow for the: 1) processing of many streams in loops, thus freeing the user from repeating tedious click-and-drop tasks; 2) computation of virtually any derivate or aggregate quantity from the data; 3) distribution of the work among several processor clusters; and 4) keeping of a log file for the calculations done. This contribution presents the building blocks of this platform, and illustrates with several examples its potential to enable predictive geometallurgy. Keywords: Data mining, entropy, kernel methods, LASSO regression, predictive geometallurgy

Jan 1, 2020

By M. Yavuz

Determining the most convenient plant location is one of the most commonly encountered problems in engineering applications. This paper presents a fuzzy multiple attribute decision making (FMADM) model which is developed for the selection of the optimum plant location for natural stone factories in the mining industry. The criteria affecting the decision making process in natural stone industry were determined to solve the plant location problem in the FMADM model. To determine the optimum plant location for a new natural stone factory, which is planned to be established by a mining firm located in the Eskisehir region of Turkey, an analysis was carried out by incorporating the method and the analytic hierarchy process (AHP) method. The analysis shows that the Yager?s method can easily be applied to the selection of plant location in the natural stone and mining industry when the difficulties encountered in the application process of the AHP method is taken into account. Keywords: Natural stone, plant location, decision making, Yager?s method, analytic hierarchy process (AHP).

Jan 1, 2008

By F. Lanaro, K. Röshoff, R. Christiansson, L. Jing

This paper presents the results of a project for developing a methodology for empirically determining some of the mechanical properties of the rock mass at the Äspö Hard Rock Laboratory, Southern Sweden. Using the equations available in the literature, the deformation modulus, friction angle, cohesion and unconfined compressive strength of the rock mass were estimated. A comparison of the results using different classification methods (Q, RMR, GSI, RMi, Ramamurthy’s) was made to estimate the range of variations in the mechanical properties with the considerations of: i) the quality/quantity of the geological data; ii) the technique for partitioning of the rock mass into homogeneous domains; iii) the sensitivity and subjectivity of the empirical methods; and iv) the need for validating the empirical methods against a test case. Cet article présente les résultats d’un projet visant à établir une méthodologie, pour déterminer, de façon empirique, les propriétés mécaniques de la masse rocheuse. En utilisant les corrélations disponibles dans la littérature, quelques-unes des propriétés de la masse rocheuse ont pu être déterminées (module de déformation, angle de friction, cohésion, force de compression illimitée). Une comparaison des résultats obtenus par différentes méthodes (Q, RMR, GSI, RMi, de Ramamurthy) a permis d’établir une échelle de variations des propriétés mécaniques et de formuler une série de recommandations concernant : i) la qualité/quantité des données géologiques ; ii) la technique de partition de la masse rocheuse dans des domaines homogènes ; iii) la sensibilité et la subjectivité des méthodes empiriques ; iv) la nécessité de valider les méthodes empiriques à l’aide de nouvelles études de cas. Dieses Paper präsentiert die Ergebnisse eines Projekts mit dem Ziel, eine Methodik für die empirische Festhellung von mechanischen Eigenschaften im Gesteinmassiv zu etablieren. Durch Verwendung der in der Literatur zugänglichen Korrelationen, wurden einige Eigenschaften des Gesteinmassivs festgestellt (Entstellungsmodul, Reibungswinkel, Kohäsion, unbeschränkte Kompressionsstärke). Ein Vergleich der Ergebnisse unterschiedlicher Methoden (Q, RMR, GSI, RMi, Ramamurthy’s) wurde durchgeführt und dies erlaubte die Feststellung der Variationsskala von den mechanischen Eigenschaften, sowie eine Reihe Empfehlungen für: i) Qualität/Quantität der geologischen Dateien; ii) die Technik für Teilung des Gesteinmassivs in homogene Domäne; iii)die Empfindlichkeit und Subjektivität der empirischen Methoden; iv) das Bedarf die empirische Methoden gegen neue Fallgeschichten zu validieren.

Jan 1, 2003

By C. P. Smyth

Large volumes of quantitative geochemical data, presenting a formidable interpretation task to geologists, are generated in the course of exploration drilling for new ore deposits. The incorporation of geological expertise into computer programs developed for the interpretation of this data would improve the speed and accuracy with which it is interpreted. A detailed analysis of the geochemical log interpretation problem, together with a survey of relevant research in Artificial Intelligence and petroleum well- logging techniques, confirms, that artificial intelligence, particularly as developed in the fields of expert systems and pattern recognition, provides techniques for implementing such data interpretation programs. In addition, it provides data analysis techniques significantly more powerful than those currently applied to geochemical data, and very appropriate to the hypothesise and test&apos; character of mineral exploration problem-solving. The conversion of raw borehole log data to meaningful higher level geochemical entities, in terms of which geological reasoning may take place, is a critical step in applying these techniques to log data analysis. A method of achieving this conversion as an exercise in signal-to-symbol transformation is presented.1

Jan 1, 1987

By S. K. Lahiri, K. C. Ghanta

Design of industrial slurry pipelines is usually performed by applying semi-empirical procedures, requiring a significant experimental study for each project. The mechanisms of suspension flow are not yet completely understood and existing predictive models cover only some aspects of uniform or closely graded particle slurry flows. This paper presents a computational technique for prediction of the velocity and concentration profile in slurry pipelines based on computational fluid dynamics. This model gives numerical solutions for the concentration and velocity distributions in the pipeline cross-section. The model prediction and experimental concentration and velocity profiles were found to be in good agreement. Keywords: pressure drop; concentration profile; particle diffusivity; slurry flow.

Jan 1, 2007

A modified germanium recovery process in conventional zinc metallurgy, based on the understanding that ferric hydroxide has strong ability to coprecipitate germanium element, was presented. The relaxed lab-scale experiments were conducted to evaluate its technological feasibility. The experimental results obtained show the new process has great competitive advantage over the conventional one.

Jan 1, 2008

By C. E. Dohm

The paper serves to show the importance of both a geological model and geostatistical model that support one another in mineral resource evaluation. It highlights the advantage of reference models for the geometry, the geological, statistical and geostatistical models of various orebody types and introduces a method for quantifying the combined uncertainty in these models. The example presented reveals how the above levels of information can be applied to add value to a resource evaluation process. It is a generic example in that it is the technique of combining uncertainty in the geological model (boundaries) as well as the grade model to assess the overall risk in the estimation of the resource. Data from the coal industry is used to illustrate the techniques. The geological uncertainty is considered via categorical simulations and these are combined with simulations of the variables (grades, thickness,) being estimated in the resource. The simulation techniques used are based on the application of GSLIB software1and a general discussion of the two simulation processes is included. In conclusion the paper demonstrates how the results of two types of conditional sequential simulation can be combined to produce confidence limits that take both uncertainties into consideration. This technique does not replace the resource estimation; it serves as an additional tool to quantify confidence in the resource evaluation model. The topics considered in this contribution are in terms of continuous improvement of mineral resource evaluation.

Jan 1, 2003

By R. J. Davidson, M. V. Nkosi, V. Veronsee

When activated carbon is used for the recovery of gold and silver from Witwatersrand gold-plant solutions, severe fouling of the carbon by calcium carbonate is experienced. Also, difficulty is encountered in the retention of the adsorbed silver on the carbon because it is displaced by gold. The acidification of plant pregnant solutions before they are contacted with carbon was therefore investigated as a means of overcoming these shortcomings. The results from batch laboratory experiments on the effect of pH on gold adsorption from plant solutions and from synthetic solutions of high ionic strength indicated reaction rate optima in the region of pH 5 and below pH I. The effect of pH on the equilibrium capacity constant for gold adsorption onto activated carbon was also studied, using both a plant solution and a synthetic solution of high ionic strength. In the case of the plant solution, the results suggested only a marginal change in carbon capacity for gold in the pH range 12 to 6, with significant increases in capacity at lower pH values. In the case of the synthetic solution of high ionic strength, the capacity constant was found to increase steadily as the pH was lowered from 12 to I. It was also found that the gold adsorption capacity of the carbon was significantly better for the synthetic solution. No precipitation of gold from the pregnant solution (gold content approximately 6 g/t) was noted as the pH was decreased to values as low as ,. However, about 25 per cent of the 0,6 g/t silver content was found to have precipitated when a pH value of 3,0 was attained. Further substantial precipitation of silver took place as the pH was lowered further. The investigation was extended by the passing of suitably acidified gold-plant solutions through one or more columns containing activated carbon. Preliminary results showed that the particle size of the carbon had a significant effect on the rate of gold adsorption. No displacement of adsorbed silver by gold was observed to take place at an influent pH of 5. In a typical continuous &apos;merry-go-round&apos; operation involving three columns in which gold was eluted from the lead column every 48 hours, effluent values averaging 0,001 g/t gold could be consistently achieved under simulated plant-operating conditions. The results were obtained at relatively high velocities of influent solution, resulting in very little hold-up of gold in the carbon-recovery circuit. More than 99,9 per cent of the gold and more than 99,8 per cent of the silver was recovered in the adsorption circuit, while the elution data indicated an average elution recovery of 99,8 per cent of the adsorbed gold and 98,2 per cent of the adsorbed silver. Elution of the carbon was carried out at 91 QC. This involved pretreatment of the carbon with a sodium cyanide solution, followed by elution with deionized water. At a loading flowrate of 66 bed volumes per hour, the indicated take-up of metals on the carbon in the lead column was as follows; 53 k g/t gold, 6 k g/t silver, 57 k g/t copper, 14 k g/t nickel, and I k g/t zinc. Only a trace of cobalt was adsorbed. At an elution rate of 1,7 bed volumes per hour, the lead column was found to be completely stripped in under 5 hours, with concentrations of gold in the eluate reaching 6 to 7 g/l. Besides the excellent adsorption and elution results obtained when acidified pregnant solution was used, no fouling of the carbon was indicated, and the pressure drop across the three columns was considered to be well within practical limits. When compared with conventional zinc precipitation, the carbon process would appear to have considerable economic merit, with strong indications that significant savings would be possible both in capital and operating costs. Further pilot-plant experiments, preferably on a gold plant, would be required before a meaningful cost comparison could be made with the existing process.

Jan 1, 1979

By N. R. Shoko, J. Chirasha

Refractory design remains the most fundamental factor in furnace construction. Refractory design details and proven technology consideration is of paramount importance to come up with an optimum furnace life and to maintain productivity in the life span of the furnace lining. The failure to produce a technically or operationally durable refractory design lining could give rise to pre-mature deterioration of the refractory lining and furnace shell. The premature failure of the furnace lining will lead to extensive heat losses, furnace bath shift, change in taphole orientation and alteration of the Pitch Circle Diameter. A combination of these were experienced at Zimbabwe Alloys? new high carbon ferrochrome furnace. The Zimbabwe Alloys experience has shown an excellent furnace performance in the first two years of operation although signs of an anomaly showed within the first six months of the new furnace. Production slowed down due to induced problems from refractory failure causing furnace distortions impacting on the availability of the furnace and smelting capacity. This paper presents the lessons learnt, measures taken to deal with the premature failure and constraints within which the situation was managed.

Jan 1, 2007

By J. M. Stewart

The purpose of my few comments is to try to create a healthy perspective to constructively link considerations of the sessions to follow to those of the earlier sessions. I propose to do this by considering some of the issues and priorities related to the development of backfill systems and technology for South African gold mines.

Jan 1, 1988

By F. R. Deist, R. P. Plewman

Discussion: A. Hazell (Associate Member) and T. J. Kotze (Graduate Member): The authors must be congratulated on the development of a versatile computer programme for determining the stresses and displacements resulting from mining operations. As a design tool it will no doubt take its rightful place together with the analogue computer. Union Corporation made use of this digital computer programme whilst still in its development stage to determine the stress distributions which were causing the unexpected failure of the Marievale sub-incline shaft. Two features arising from this investigation may be of interest to members, namely: A. The solution to the problem of stabilizing a rectangular inclined shaft, which turned out to be contrary to accepted mining practice, and B. A comparison between the results obtained with the pure digital system and the analogue computer. A. The shaft is nine ft high and 20 ft wide, dipping at 9° to the horizontal and crossing the bedding planes. Fig. 1 is a plan and Fig. 2 is a section of the sub-incline shaft pillar area showing the relative positions of the shaft and reef as well as their respective dips. The deepest point in the shaft is 3 300 ft below surface and the requirement of a stress free ground surface may not be satisfied. It also means that the original gravitational stresses are low. A 900 ft wide pillar was left to protect the bottom section of the shaft, the top section being understoped years ago. Extraction of the pillar was started at the beginning of last year, mining operations being carried out in the accepted manner, starting beneath the shaft and mining outwards. The approach did, however, turn out to be the wrong one, because failure of the shaft was noticed soon afterwards. Even small movements were serious in this case due to the low clearance between the skips and the shaft supports. During October, 1968, failure between benchmarks 8 and 10 (see Fig. 1) became so excessive that hoisting speeds had to be reduced. Failure continued to occur and, by the end of March, 1969, failure had propagated up the shaft as far as benchmark 7, and down as far as benchmark 12. As this shaft had a tight hoisting schedule it was imperative that a quick solution be found to arrest the failure.

By C. M. Rule

High pressure grinding rolls (HPGR) technology has come a long way in its application for comminution duty in hard rock mineral processing in the last three years. Several major projects in copper, nickel, gold, molybdenum, platinum, and iron ore have opted for this technology. Advances in wear abatement technology have established the HPGR as a reliable machine with the required high utilization and availability. The HPGR captures the imagination as the next step change improvement in ore processing, based on the following benefits: ?Energy efficiency (potentially 10?30% more efficient)?very topical in an increasingly ?green? society, and in times of rapidly increasing energy costs and availability concerns. 2008 has shown this to be especially important in Southern Africa ?High (and stable) throughput with a relatively small footprint ?Lower operation cost ?Liberation benefits ?Creative ?mine-to-metal? system improvements made possible by HPGR. The platinum industry, renowned for its historically conservative approach, has not been left behind with two significant new HPGR installations, one in Platreef application and one in UG2 application, commissioned in 2008. While the decision for the Platreef application was driven primarily by comminution circuit capacity and design imperatives, the UG2 application seeks to develop a flowsheet that will have a significant recovery benefit in addition to capacity increase and reduced operating cost. The Platreef application of HPGR also provides the opportunity to introduce a novel comminution flowsheet and to demonstrate exceptionally low wear rates treating very hard, abrasive and variable ore types. The HPGR lends itself for inclusion in existing SABC circuits to increase the capacity of the plant and mills. With current PGM prices many operations are attracted to the HPGR technology benefits. The HPGR clearly has the potential to transform entrenched opinion and provide decision makers with significant alternative comminution options. This paper aims to provide an overview of the current applications and to speculate on the transforming stimulus that the HPGR exerts on industry.

Jan 1, 2009