Search Documents

By Ken Roosa

Blue Circle Atlantic of Ravena, New York, operates a four million ton per year quarry. The quarry management objective is to maximize crusher throughput tonnage while optimizing the aggregate cost to drill, blast, dig, haul, and crush a ton of rock. To meet this objective, Blue Circle,s blasting program combines, large diameter production blastholes with medium diameter satellite blastholes.

Jan 1, 1989

By S Lukovic, Robert Briton, Calvin J. Konya

Investigators have reported that charges which are decoupled from the borehole wall produce different fragmentation then those which are fully coupled. The difference in effect could be as a result of energy doss during transmission across the air gap or it could be due to the change in detonation characteristics of the explosive as a result of the change in confinement on the charge during detonation. In order to better understand the phenomena of decoupling, a research project was conducted at the United States Bureau of Mines Station, near Pittsburgh, Pennsylvania. It was decided to use shock and bubble energy tests along with simultaneous velocity measurement to determine the mechanics of decoupling and energy transmission. Two explosives were selected for the test, one dynamite and one water gel. Test results indicated that decoupling could both boost the total energy output of the explosive and that further decoupling would drop the energy output.

Jan 1, 1987

By Charles H. Dowding, Catherine T. Aimone

Rock particle sizes were measured at fourteen steep-slope Appalachian coal mines during production blasting. The distribution of rock sizes shows the effects of inter-hole timing, sequence of hole initiation, as well as charge distribution within each shot. Blast design parameters were selected to: (1) minimize displacement of broken rock conforming to throw control required of mining methods, (2) minimize seismic effects, and (3) create breakage at a cost economical to mining operations.

Jan 1, 1983

By Lawrence W. Hallanger

Anaheim Bay, located at Seal Beach, California, is the site of the Huntington Harbor development of waterfront homes and marine facilities. The main entrance to Anaheim Bay is a relatively narrow channel connecting the bay with the Pacific Ocean which runs under California State Highway One. During the development of Huntington Harbor the old highway bridge was replaced with a new, higher bridge to allow for boat passage through the channel. At that time only the main span decking of the old bridge was removed, leaving the support pillars and the approach ramps in place (see Figure 1). The narrowness of this channel, plus the increasing boat traffic created a situation in which public demand for the removal of the old bridge became significant. Because the bridge was located within the boundaries of the Seal Beach Naval Weapons Station (see Figure 2) the Navy became involved in the bridge removal. Eventually the task was assigned to the Naval Amphibious Construction Battalion One and work began in early 1974.

Jan 1, 1975

By U. Steiner

Electronic detonators have been in commercial use for a decade, with an excellent safety record. This paper lists known incidents involving electronic detonators. Typical standards required by regulatory bodies for static electricity and electromagnetic fields are reviewed. The performance of some detonators is compared to these standards; in general the minimum standards are easily exceeded. The general resistance of electronic detonators to extraneous electrical energy that can be derived from the body of test results is compared to danger levels for exposure of humans to these energies; it is shown that electronic detonators can safely tolerate higher electrical energies than people can. This comparison includes comparable data for electric detonators, which are shown to be more vulnerable to extraneous electrical energy than people are. Electronic detonators also bring significant safety benefits in blasting due to their testability, two-way communications, reliability, programmability and precision. The links between these attributes and enhanced safety are discussed with examples from actual blasting. Although electronic detonators are usually more vulnerable to extraneous electricity than non-electric initiation systems, the paper shows that the net safety benefit in handling and blasting is in favor of electronic detonators, which are the safest initiation system that has ever been offered to the mining industry.

Jan 1, 2010

By Gregory P. Lorsbach

Significant information about any blast is contained within the seismic signal generated by the blast. In this study, standard digital signal processing techniques are utilized to extract source parameter information from a seismic signal recorded at distances commonly used in compliance monitoring. Specifically, digital seismic data was analyzed using the cross-correladon and autocorrelation functions for the purpose of determining delay timing. The initial results are interpreted to indicate that: 1) Individual delays can be identified analytically but not visually for short delay periods and large source to receiver distances, 2) Delay timing can be resolved to a few milliseconds, and 3) Results can be obtained from data collected at a minimal number of locations.

Jan 1, 1991

By Walt Meglasson

"Developing technologies in demolition equipment and processes have produced a newsophistication within the demolition industry. Yet, with increasing frequency, owners,architects, engineers, and contractors reject out of hand one of the safest and most effectivetools in the demolition industry today, specifically the use of explosives and blastingtechniques in man_made structure removal. The use of explosives in any application mustbe considered as a tool, no more or less dangerous than any other type of tool, when usedproperly. Accordingly, importance must be attached to recognizing the skill, integrity, andcare of those who use it. Massive amounts of information and help are available to assistthe rock blaster, ranging from the practical to the highly theoretical, but very littleinformation exists to guide anyone considering unleashing the power of explosives instructural demolition blasting. The planning and work required to execute such projects iscomplex, and the recognition of the different applications explosives can be applied to isthe first step."

Jan 1, 1993

By Christian Dye

"The following paper focuses on the developing relationship between the members of theInternational Society of Explosive Engineers (ISEE), and the mining students from the BritishColumbia Institute of Technology (BCIT). During the past two years mining students and theISEE members have worked closely in developing a student chapter within the society and onFebruary 1st 2015, the first Canadian Student Chapter was recognized at the annual generalmeeting in New Orleans. This paper discusses the benefits that both the industry and studentsgain with a strong relationship. The mining students recognize the importance for filling the rolesof retiring members of the society and industry. Prior to 2015 the school had only offered a twoyear diploma program in mining and mineral exploration methods. That included a brief sectionin the use of explosives in the mining industry. In September of 2015 students were recruited forthe first ever Bachelors in Mining and Mineral Resource Engineering program. This engineeringdegree includes a full four month course in advanced blasting and rock fragmentation. Studentssuccessfully completing the diploma program will have an entry level of technical understandingin how blasting is conducted. The students successfully completing the bachelor degree will havean in depth technical understanding of explosives and rock fragmentation. Having this uniqueand dynamic multi-level program provides the explosives industry with a pool of talent that canbe used to fill positions with graduates for all levels of the blasting industry."

Jan 1, 2016

By María Virginia Ramírez, Alejandro Alarcón, Alea Reyes

Reactive grounds (presence of FeS2, CuFeS2) can create hazards in a mine; misfires to premature deflagration or detonation of loaded blast holes. This occurs because some minerals can react to ANFObased explosives. Due to a high potential event that occurred in The Mine in 2013, The Mine and the Explosive Provider (“The Company”) are conducting a soil characterization of the areas containing reactive sulfides. This study was planned along with The Mine and it is being developed by a multidisciplinary team.

Jan 1, 2018

By S S. Kahlon

India is a large and growth market for explosives and accessories, which has dramatically changed from complete import dependence to self sufficiency, and now has an exportable surplus. The largest single user is coal mining which is continuing to show a healthy growth with opencast mining becoming increasingly dominant. The explosives industry has kept pace with mining and today all the well renowned explosives technologies of the world are available in the country. While slurry explosives are popular in large diameter, NG based explosives continue to be preferrred in small diameter usage. Emulsion explosives have had a good market response. ANFO usage is limited due to local reasons. As the mine size is increasing, the demand for bulk-on-site explosives is growing. Prices of explosives and accessories are cheap compared to international levels. The user industry is mainly Government owned mines whose profitability is not satisfactory. Explosives industry is over licensed in terms of manufacturing capacity, which is likely to put pressure on the viability of some of the explosives manufacturing units. Scope exists for optimization of blasting parameters through the use of computerized blasting models. The explosives industry is faced with new challenges and opportunities.

Jan 1, 1987

By Pierre Mousset-Jones, Geraint W. Harris, Robert Karlin, Jaak Daemen

In order to minimize the ore dilution induced by blast movement in surface mines it is necessary to quantify such movement. This will make it possible to more accurately locate the grade boundaries on the surface of a blasted rockpile prior to excavation. This paper describes the development and testing of a method to accurately measure the direction and magnitude of sub-surface blast movement. The technique involves the use of magnetic "radiometry, using a cesium vapor "radiometer and real-time differentially corrected, GPS system, to locate the post-blast position of magnetically enhanced target objects, whose pre-blast locations are known, without disturbance of the blasted rock. The objective is to design an accurate and efficient technique which can be integrated into a mines production cycle.

Jan 1, 1997

By Lewis L. Oriard

Ground vibrations associated with blasting are generally in a higher frequency range and of shorter duration than those generated by earthquakes, and the intensity scales for earthquakes cannot be applied directly to blasting vibrations without modification. Further, the profession does not need an intensity scale merely to estimate vibration intensity. If the blasting in question was not monitored instrumentally, it is a simple matter to estimate the range of intensities based on published prediction formulae or data from various sources such as Oriard (1), Nicholls et al (2), Hendron and Oriard (3), Siskind et al (4), and others. However, the profession has a serious need, for purposes of evaluating damage claims, to understand the relationships between vibration intensities and the levels of observed effects. The criteria for threshold damage do not apply to typical cases which usually involve structural damage. If the damage in question would have required ground vibration with a particle velocity of, say, 20-120 ips, damage is not verified by showing that the vibration merely approached a suggested limit to avoid threshold damage. That is not the question. This paper provides some guidelines for comparing severity of damage to intensity of vibration which would be required to cause such damage, much as is done when determining earthquake intensities. In addition, this paper includes a discussion of strain amplitudes induced by environmental forces, the predominant causes of damage to structures. Also, certain popular myths regarding blasting damage are discussed in the paper. Due to space limitations, the paper will not include a discussion of airblast effects.

Jan 1, 1989

By Don Thompson

The Minntac Mine drills and blasts approximately 75 million long tons of taconite per year. This requires drilling one million feet of 1 6-inch diameter holes. We are in the process of replacing our old generation rotary blasthole drills (Gardner-Denver 120's and Bucyrus-Erie 61R's) with new generation rotary blasthole drills (Bucyrus-Erie 59R's and P&H 120A's).

Jan 1, 1998

By Hideaki Kitajima, Ryo Sakamoto, Katsuya Sasaki, Maehata Hidehiko

The Electric Discharge Impulse Crushing System (EDICS) is a technology for carrying out crushing by using electrical power and nitromethane. It is designed for construction tasks such as splitting of concrete and rocks.The EDICS consists of an electric discharge generator that supplies a high-voltage high-current pulse, a cartridge that generates power by using electric discharge energy, and cables that connect the electric discharge generator and the cartridge. The cartridge contains a thin metal wire that evaporates because of the electric discharge energy and a nitromethane that reacts with this evaporated metal wire. The cartridge can be used to generate a high pressure on the order of gigapascals within a time interval of several hundred microseconds, and crushing power equivalent to that generated by explosives is generated during this period. In recent years, the EDICS has been widely used in Japan because of its good performance and favorable characteristics.

Jan 1, 2011

By Jim Peterson, Ricardo Freire, Mason Biernat

Variable nature of rock and face conditions, varying execution and changing nature of blasting are making ongoing optimization challenging. Intelligent planning and on-going analytics are required to mitigate variability and convert blasting into a predictable outcome by use of technology. Blasting operations generate a huge amount of data which can be used intelligently for optimization. In this paper, details are provided of a system which is used for blasting data collection in the field – Key details around blast parameters, explosives, initiating system details, video, photographs, vibration and fragmentation are collected in a cloud-based platform. Data can also be collected through a mobility device in the field (even without internet connectivity) and synchronized with cloud-based system. Also, data from various sources can be imported in excel formats in the software including from upstream and downstream processes from blasting. App also gives indication about exceeding of vibration, air blast overpressure, fragment size etc. Thus, making it possible to perform QA-QC before charging and deciding initiation timing and sequence at the blasting site. The data can be processed and analyzed to spot trends, help predict events, and formulate strategies at the design and execution stage. Data gathering of blast parameters, explosive used processing and analysis can be used to optimize operational efficiency, improve safety and environmental controls.

Jan 1, 2019

By Cam B. Grundstrom

This paper will describe blast design modifications that have been made at the Island Copper Mine, near Port Hardy, British Columbia. To date, two additional designs have been implemented in an effort to reduce final wall damage and increase productivity. The typical blast patterns in use at Island Copper were monitored in an effort to build up data to which new designs could be compared.

Jan 1, 1994

By AK Chakraborty, AK Raina

Burden of drill hole is third most sensitive parameter effecting the ground vibration in blasting apart from maximum charge per delay and distance. Various types of burdens can be seen in practical bench blasting situations. Burden can be expressed as drilled burden and initiation burden. Drill holes may have various front row burdens (toe burden), which may be different from the designed burden. In order to ascertain the impact of front row burden as well as the initiation burden on intensity of ground vibration and air overpressure experiments were conducted in sandstone overburden benches of an opencast coal mine and limestone quarry. Blast trials were carried out in cognisance of both drill and initiation burden while keeping all other parameters constant. Effect of front row burden was also extensively studied by keeping almost all other parameters constant. The results of the study reveal that there is substantial influence of front row burden on the vibration and air overpressure. The statistical analysis of vibration and air overpressure data with drilled burden and initiation burden gives significant evidence that the level of peak particle velocity of vibration (Vmax)) is reduced by reducing effective burden with modification of initiation. Data analysis carried out for air overpressure versus initiation burden shows that reducing effective burden with modification of initiation results in increasing the level of P. The study reveals a qualitative assessment of the influence of burden on the blast induced vibration and air overpressure. The study also recommends to modify the initiation pattern to reduce the effective burden in order to reduce the vibration, without disturbing the fragmentation.

Jan 1, 2004

By Jason Baird, Philip Mulligan

This report details the preliminary calculations governing the underwater collapse of an oil pipe via explosive lensing. An explosive lens changes the detonation wave produced by an explosive by changing the geometric conditions of the explosive (Zukas and Walters, 1998). Multiple lenses can be focused on a central location, generating a series of precise detonation waves collapsing in on a specific point. This report will assume a spherical-shaped, single explosive charge and explain how the authors determined the explosive charge size needed to seal a metal pipe while focusing on one explosive charge acting on part of the pipe. Future calculations will analyze the combination of multiple explosive charges acting on the pipe as a whole.

Jan 1, 2013

By Syed Haq, Kyle Optt, David Campo, Doug Anderson

Limitations on allowable levels of vibration from construction activities generally consider either annoyance or damage. While activities such as drilling and roller compaction primarily create annoyance, the major concern for blasting is usually damage. Many years of research have developed correlations between peak particle velocity and either threshold or structural damage. We emphasize the term “correlation” for two reasons. First, peak particle velocity is only a single-valued representation of a vibration waveform, and does not characterize it completely. Second, a given peak particle velocity by itself, even a particle velocity waveform, will not damage anything – strain does. Why not measure strain all the time? Strain is very localized, and can vary substantially over short distances, so choosing the appropriate strain measurement can be difficult. Measurement of strain is appropriate when either the behavior of a specific structural element is needed, or the overall response of a structure can be adequately represented by a well-selected strain measurement. We will discuss the appropriateness of both particle velocity and strain as deformation and damage descriptors, in general. We will also describe a specific case history, from a tunnel project in New Jersey, correlating strain with peak particle velocity. Finally, we will make recommendations for the choice of measurement type for some common situations.

Jan 1, 2004

By Stuart Brashear, Steven Bell, Donald Smith

This Limestone site required the removal of a bench containing high quality rock located in close proximity to sump and pit pump. The sump and associated electrical box were below the bench that needed to be blasted and located only 70 feet (21.33 meters) away. It was proposed to blast material needed without moving or disturbing the pump or electrical junction box. The area to be blasted was flown with a drone and stitched into a 3D orthographic model. Proprietary blast design software was used to create a blast design solution that would allow for a series of blasts that would provide required fragmentation and muckpile development and not disturb the sump or electrical box. A drill patten was created for each blast using the burden heat map and 3D face profiles created from the 3D orthographic model. Timing contour lines and muckpile displacement predictions were used to create timing sequences for proper face movement away from the sump and electrical box. The shot designs were laid out with a GPS system to insure hole location accuracy. All holes were remeasured for proper face burdens using the 3D model and Boretrak®® data collected after drilling operations were completed to insure hole locations were within face burden tolerances as derived by the burden heat map. After each drill log was reviewed, a charge loading scenario was created for each hole. The timing design created, for each shot and was reviewed and adjusted as needed with regard to desired muckpile displacement away from the sump and electrical box. Blasting results were satisfactory, with fragmentation and muckpile development consistent with the calculated throw from the blast model, with no rock hitting the pump or box and no rocks striking the sump water and disturbing the pump motor.

Jan 21, 2025