Search Documents

By R. K. Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a cascading pillar failure, occurs when one pillar in the mine layout fails, transferring its load to neighbouring pillars and causing them to fail in succession. Recent examples of this kind of failure in coal, metal and non-metal mines in the USA are documented. Mining engineers can limit the danger presented by these failures through improved design practice. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This is used as a basis for three design approaches to control cascading pillar failure: containment with barrier pillars during pillar splitting; prevention with panel pillars of high width-to-height ratio and small-centre mining; and full extraction by retreat mining

Jun 19, 1905

Errors in ore reserve estimation can occur during drilling and sampling, sample preparation and analysis, geological logging and modelling, database construction, statistical or geostatistical evaluation, selection of economic parameters, selection of ore reserve method and assessment of mining constraints. Core sample recovery can be a major source of error, and it is proposed that the modelling of grade, metal accumulation and thickness should be accompanied by the modelling of core recovery (or core loss) so that for each ore block a weighted block recovery factor is obtained. This gives a good indicator of the reliability of a reserve estimate. It is suggested that a resource reliability rating (RRR) system be established to quantify what is meant by geological assurance and to combine this with an estimate of the precision of estimation as gained by geostatistical analysis. Proven and probable minable reserves would be those with an RRR better than 50% and a precision of estimation better than 20%

Dec 1, 1996

By P. J. Baguley

The model has been developed on the basis of the observation that the partitioning behaviour of a particle is related to its calculated terminal velocity. It utilises a theoretical calculation of the terminal velocity of each particle class. This is then correlated with the observed partition data for a plant separator using empirically-derived functions of operating conditions which take into account effects such as bath turbulence, holes in drum lifters and feed arrangements. The model successfully decouples the effects of medium density and viscosity and is appropriate for any bath-type separator. The correlation between calculated terminal velocity and actual partitioning behaviour was established and modelled using data obtained from two Wemco drums treating Fe and Mn ores. The model can be used to predict the prevailing size-by-size partition curves and the separation (product grades/recoveries) given the washability of the feed and operating conditions. Simulations are used to show that, for the treatment of Fe ore, there is a maximum medium density beyond which product grades fall and that this maximum decreases as the proportion of magnetite in the medium increases. This is attributed to the dominant effect of viscosity at higher medium solids concentrations

Jun 18, 1905

By P. H. Davenport, L. W. Nolan

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Geochemical mapping provides a direct approach to delineating areas of epigenetic mineralisation and for relating the regional distribution of this mineralisation to an overall tectonostratigraphic and structural framework, as well as to extensive areas of hydrothermal alteration. Organic lake sediment is a widely available and effective sampling medium for regional geochemical mapping in Newfoundland, that has proved to be valuable in Au, Sb and W exploration

Jul 1, 1991

By Xuejing Xie, Tianxiang Ren

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Standardised stream-sediment sampling procedures have been used in mountainous and hilly terrains. Special sampling procedures were developed for application in remote environments, such as high mountains, desert, semi-desert, karst and loess-covered regions. The diversified analytical methods used in more than 20 analytical laboratories participating in the project have been unified into two multi-element, multi-method analytical systems. A unified data monitoring procedure was developed based on primary and secondary standard samples. To date the project has covered about 4 000 000 km2 and the aim is to complete the coverage within the present decade

May 1, 1991

By A. D. Mukherjee, H. N. Bhattacharya

Middle Proterozoic sulphide ore mineralisation occurs in isolated blocks of the NE-SW trending Delhi fold belt composed of Delhi Supergroup rocks. The Ajari-Basantgarh-Pipela belt forms part of the longest, widest and westernmost tectonic unit of the Delhi fold belt and consists of amphibolites, metapelites, quartzites and carbonates. The metapelite lenses and associated amphibolites host pyritic copper mineralisation. Mineralisation takes the form of sheet-like bodies consisting of ore lenses of various sizes interlayered with host or associated rocks. Massive, banded and disseminated varieties of ore are found. Pyrite is dominant with subordinate chalcopyrite and sphalerite. Pyrrhotite, galena, cubanite, mackinawite, marcasite and freibergite constitute the minor minerals. The characteristic features of the ores suggest a possible correlation with Besshi-type deposits, and the closely associated amphibolites are interpreted as low-K tholeiites of a fore-arc setting

Jun 19, 1905

By P. Grainger, P. G. Kalaugher

Paper presented at conference and first published in preprint volume of: Risk assessment in the extractive industries, held in University of Exeter, 23-24 March 1994. London: IMM, 1994. Large, unpredicted ground movements resulting from open cast or underground mining present risks to the safety and economy of extractive industries. As large, sudden failures are usually preceded by small displacements at a much slower rate, the detection and monitoring of these minor changes to the ground surface provides a means of assessing the risks. It is recommended that a visual approach is often preferable to surveying or fixed instrumental measurements. An optical system has been devised, incorporating a 35 mm camera, which allows an immediate comparison on site between a colour transparency taken on a previous inspection and the scene it represents. The observer fuses the transparency stereoscopically with the directly viewed scene. The impression is close to that of normal vision except that differences in detail which have occurred since the transparency was taken are immediately obvious, enabling a qualitative assessment of changes to be made on site. If repeat photography is required it can be taken with exactly the same alignment and coverage. The two images are then available for office analysis using simple micro-photogrammetry

Apr 1, 1996

By S Durucan, A Korre

The application of simple methods of statistical analysis, coupled with geostatistical analysis and geographic information systems, can only summarise and give an outline of the spatial distribution of the parameters measured. Spatial analysis of the components or factors calculated, through principal component analysis or factor analysis, allows assessment of the geographical distribution of the dominant processes contributing to soil composition and/or contamination. Neither of these tools, however, distinguishes between the different sources of pollution. The application of canonical correlation to the data, driven by expert appraisal of the potential pollution sources, allows their quantitative and spatial assessment while GIS provides the environment in which to organise and present the results. The methodology is illustrated by its application to soil-contamination data from the Lavrio area in Greece, where silver-bearing orebodies have been mined for more than 25 centuries

Jun 21, 1905

By T. Ogasawara, J. P. Barbosa, A. J. Monhemius, F. T. Da Silvia

A thermodynamic analysis of the sulphation of rare-earth phosphates and the water-leaching of rare-earth sulphates was used to guide experimental work on the sulphation and leaching of concentrates from Pitinga. It was concluded that the sulphuric acid digestion of xenotime is technically feasible and could be used industrially to produce yttrium and other rare-earth oxides. Yttrium extractions of more than 90% were obtained by digestion at 503 K for 4 h at an acid:concentrate ratio of 2:1 with particle size -0.053 mm. The apparent activation energy at temperatures less than 473 K, as determined from the Arrhenius plot, was 11.0 kJ/mol, indicating that the reaction is controlled by the diffusion of the reactants or products through the sulphate layer

Jun 19, 1905

By C. L. Schneider, C. O. Gomes, R. P. King, J. A. Finch, D. Lin

Discussion is presented by Prof. King and Dr. Schneider of the paper by Lin, Gomez and Finch published in Trans.IMM C, vol.104, 1995, p.C155-C161. They conclude that the correction procedures used for simulated observations of simulated capped spheres are not reliable when applied to mineralogical data and that their relative ranking should not be extrapolated to other situations. Properly regularised solutions obtained with the use of appropriate kernels can be safely used for routine mineral liberation work and can be calibrated accurately against real mineralogical samples in the laboratory

Jun 19, 1905

By W. E. Stephens, A. J. Boyce, D. Lowry

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. An integration of S isotopic, fluid and mineralogical data for granitoid-related mineralisation showed that the porphyry systems had a predominantly subcrustal magma source, but the inner magma pulse of two-mica granite in the Fleet pluton was derived mainly from reduced sediments. The porphyry-style mineralisation formed from boiling fluids at high crustal levels, with a moderately saline fluid percolating down to the upper veins as they cooled but not penetrating the deeper Talnotry deposit. Veins in peripheral greywackes have a significant magmatic component but also incorporated CO2-rich components and metals released by dewatering of host sediments in response to granitoid intrusion. The low grade of regional metamorphism resulted in the significant fluid input from country rocks which led to the more exotic mineral compositions, especially where argillaceous sediments were involved

Jun 19, 1905

By S. Babendererde

The twenty-ninth Sir Julius Wernher memorial lecture of the IMM, presented at Tunnelling '97, London, 2-4 September 1997. The tunnelling industry is well prepared to face the challenge from the population explosion in urban areas in the near future. Many well-established yet redundant concepts are still impeding progress, however, including the prediction of excessive surface ground settlements. The correct selection of TBM can minimise these, and ground deformations can be avoided completely if the appropriate techniques are applied. Advanced techniques have been used in the Tokyo Bay Crossing, where the tunnel lining was installed by robots. Other advanced techniques include the use of a sliding slip form to give temporary support to an extruded tunnel lining, the chemical processing of ground by polymers during earth-pressure balanced tunnelling and the use of electronic monitoring and steering devices in TBMs. There will be challenges to tunnelling in urban environments, as open cut techniques will no longer be tolerated. Two examples of mined stations are briefly discussed

Jun 19, 1905

By T. Serradj

A study has been carried out to: develop a method for routine characterisation of rock strength and drillability through the particle-size distribution of crushed or drilled rock products, defined by the Protodyakonov index; establish correlations between the Protodyakonov index, uniformity coefficient and the constant grading equations; and propose an alternative rock characterisation index to classify rock strength and drillability for the northeast region of Algeria

Dec 1, 1996

By D. M. Milne, P. J. Lunder, R. C. Pakalnis

During the mining of an open stope, deformation of the hanging-wall and the potential for dilution generally increase with the size of the exposed hanging-wall. Excluding discrete structures that may delineate unstable blocks, the mechanisms that drive hanging-wall deformation and possible dilution comprise several factors which can include elastic, plastic and discontinuum deformation. These stages of deformation are not mutually exclusive and at any point during mining all three of these mechanisms may be acting on the hanging-wall rock mass. Computer modelling techniques are available to analyse the three stages of deformation, but the difficulty lies in trying to obtain realistic rock mass properties for input and in determining when each stage of deformation is acting. Instrumentation data can be used to predict the effect of continued mining. However, it is often difficult to calibrate numerical models against field data owing to the large number of input parameters required. An empirical approach is recommended that uses two new parameters, the radius factor and the effective radius factor. A method is proposed for predicting the effect of continued mining from existing deformation and dilution data for a given hanging-wall

Apr 1, 1996

By M. V. Swain, N. Bristow, R. D. Dukino

During mining, crushing and handling the size of iron ore lumps decreases. Key factors in determining the amount and size of fines that are produced are the mechanical properties of the ore. In a continuation of earlier work on the same ores the mechanical properties of three Australian iron ores from Yandi, Koolan and Mt. Whaleback were determined. In particular, fracture toughness was investigated in greater detail by examining its relationship to crack length using the compact tension test. The elastic modulus and strength of the ores were also determined in flexure and compression. The results were interpreted using Weibull statistics, enabling the ores to be ranked according to strength and elastic modulus. These results, together with data on the mechanical response of the ores to stress and observations concerning the effect of mineralogy on cracking, provide a coherent understanding of the mechanisms involved when the ores fracture

Jun 18, 1905

By S. Henley

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: The database: a pre-requisite for large-scale use of AI in mining). Artificial intelligence is a term which has been widely applied to different techniques including rule-based systems using inductive and deductive logic algorithms, neural networks, learning systems and genetic algorithms. In principle it should be applied to adaptive statistical techniques. Some of these applications have been coded in languages which are specifically suited to the novel requirements of AI but are not easy to integrate with more traditional computing methods. Efforts have been made to bridge the gaps, particularly with database management systems and such efforts at integration should provide the key to future success in the application of AI. A field which has been termed "knowledge engineering" cannot be credible as such if it fails to provide easy access to raw materials of "knowledge" i.e. the data residing in databases. In the mining industry there are a number of significant areas in which AI could usefully be applied throughout the industry, but its advance is slow because of the lack or inefficiency of such database links. Current development of object-oriented database systems for geology and mining holds out hope for such integration in the foreseeable future

Apr 1, 1994

By D. Witchard, G. C. Penny

An important conclusion of the study is that altering the properties of the granulation water is a practical way of improving the sintering performance of blends that contain porous ores, and more work is under way to investigate other additives. Previous studies of iron ore blends containing pisolite ore showed that losses in sintering productivity were a result of deteriorating green-bed permeability. Pisolite ores are extremely porous and absorb a proportion of the water added during granulation. Although increased water addition could be used to counteract losses in productivity, the current study examined methods of inhibiting water absorption by pisolite ore as a means of improving productivity. Additives were used to alter the properties of the granulating water. With no increase in mix moisture contents pilot-scale sintering studies showed that sugar-based additives gave productivities that are higher than those obtained for a comparable ore blend containing haematite rather than the pisolitic ore. Several techniques of adding the sugar to the sinter mix were examined and found to increase productivity to varying degrees. Theoretical considerations, in some cases supported by experimental results, indicate that sugar-based additives not only inhibited water absorption by porous ore particles but also improved the permeability of the sintering bed. The study also suggested that, contrary to some commonly held views, the highly reactive nature of Yandi ore from Western Australia is beneficial for sintering. Porous ores enabled the formation of a strong sinter at fast flame-front speeds-both good strength and a short sintering time are requirements for high-productivity operation

Jun 18, 1905

By H. Y. Sohn, Hang Goo Kim

Computer simulations were carried out using calcium ferrite slags containing 25 wt% CaO, and the results compared with those obtained using fayalite slags. There was little difference in overall elimination of Pb and Bi, but elimination of Sb and As was much lower with calcium ferrite slag. When calcium ferrite slag is used only in the converting stage and fayalite slag in the smelting stage, as in the Mitsubishi process, the contents of Sb and As in the blister copper can be kept to reasonable levels. This allows advantage to be taken of the considerably higher iron oxide-holding capacity of calcium ferrite slag than of fayalite slag at the high oxygen potential under converting conditions, thus preventing precipitation of magnetite. Satisfactory agreement was obtained between predicted values and observed data from a Mitsubishi converter

Jun 18, 1905

The deposit was discovered during systematic reconstruction of the geological history of glacial overburden, which averages 6 m in thickness over 80% of Sweden, by geochemical sampling and searching for small grains of eroded bedrock. The gold is mainly concentrated in and around high-grade quartz veins within a broad shear zone, though the correlation coefficient between quartz and gold in samples is not significant. Production from two pits, now connected, in the Central and Eastern orebodies has increased steadily from 1 238 kg Au in 1989 to 2 120 kg in 1994, the highest in Europe. The mine has adapted and improved its mining methods to achieve significant productivity increases and cost reductions. Most of the improvements have been achieved through a better understanding of the controls on mineralisation and of the implications of those controls for selective mining. Geostatistics has played an important role in the quantification of grade variability and gold occurrence. Better blasting and loading techniques have improved selectivity, grade control has been enhanced by a grade-control drilling programme, and significant improvements in mineral processing have been made

Dec 1, 1995

By M. Lombardero, J. Garcia-Guinea, J. Taboada, B. W. Roberts

The structural, textural and mineralogical properties of the slate formations of NW Spain make it the most important district in the world for quarrying roofing slates. Over the past 10 years the introduction of new methods has increased yields from 2 to 13%. The main factors affecting quality are quartz grain size less than 75 micrometres, homogeneity of slaty cleavage and S0-S1 intersection angle, very low metamorphic grade, absence of secondary foliation, beds 10-12 m thick and low content of oxidisable Fe sulphides. The two main controls on fissility are lithology and deformation accompanied by metamorphism. The minimum natural block size should be 0.6 m3 but this volume can be reduced for modern cutting tools such as diamond wire, chain and circular saws. Structural analysis is crucial in exploration and quarrying, as shown by the prospecting methodology applied at Dominio de Truchas in central Spain and the computer analysis of rock mass discontinuities at Casaio quarry

Jun 19, 1905