Search Documents

By Juan Estrada, Mirtha Frómeta, Rubén Alcalá, Emilio Montejo, José Castellanos, Juan Berto, María Rivas

"The oxidized nickel ores from San Felipe deposit are composed mainly Smectites which gives to the pulps very unfavorable rheological .properties (cinematic viscosity and high shearing strength) for transportation processes (pumping), very low settling velocities and very low thickened pulps. These properties do not allow the preparation of high % solids, which affects the economic efficiency if a high pressure acid leach (HPAL) process is used. Pulps of close to 30% solids have very high BYS making pumping impossible. CIPIMM developed three technologies to solve these problems and to substantially increase the % solids in the pulps to be leached without a thickening step. These technologies are: • CIPIMM 2. At Preparation of pulps using additives. This method is based on the effect of some additives (inorganic salts) to improve the pulp’s properties. The use of this method allows increasing the % solids in the pulp up to 40% with good rheological properties • CIPIMM 2B. Preparation of pulps by thermal treatment of the ore previous to the preparation of the pulps. This method is based on the thermal destruction of the clays structure. Its use allows to obtain pulps with 50 - 60 % solids with excellent rheological characteristics. As a collateral effect, the Ni and Co grades increases by 10 - 15%. • CIPIMM 2C. Pulp preparation by chemical treatment. This method is based on the chemical transformation of clays, to obtain without thickening, pulps with 43- 45% solids and excellent rheological properties. The use of one of the three technologies depends on the chemical and mineralogical composition of the ores and the results of technical-economical evaluations to determine which one is the best alternative before running higher scale tests."

Jan 1, 2014

The ever increasing demand for energy and the progressive depletion of crude oil resources, have renewed interest in oil shale as an alternative fuel resource. Weathered oil shale samples were assembled from El-Nakheil phosphate mine in Quseir area, Eastern desert, Egypt. The oil shale samples were prepared and analyzed by XRD (X-ray diffraction), XRF (X-ray fluorescence spectrometry), and optical microscopic techniques. Rock-Eval pyrolysis and total organic carbon were used to study shale hydrocarbon potential. A leaching procedure using inorganic and organic acids was used to selectively dissolve the oil shale associated ash forming minerals. XRD results showed that calcite is the dominant carbonate mineral, whereas primary silicate minerals are quartz and montmorillonite. SEM (Scanning Electron Microscopy) observations indicated that the organic matter is dispersed throughout the rock matrix. The acid soluble fraction upon leaching was determined to be 37.59 and 42.74 wt% by using 5% HCl and 10% HCl, respectively. The TOC was increased from 20.78 to 29.88 and 34.09 wt% by using 5% HCl and 10% HCl, respectively. Keywords: el nakheil oil shale, characterization, xrd, xrf, sem, elemental analysis, proximate analysis, ultimate analysis, thin section, rock eval pyrolysis, acid leaching

Sep 1, 2012

By Jan Svoboda, Toyohisa Fujita

The current status and history of innovation in magnetic methods of material treatment are reviewed. The milestones and key drivers of innovation in magnetic separation are identified, advantages of this technology in comparison to other physical methods of material manipulation are discussed and reasons for its failure to live up to its potential and expectations are indicated. Derailers that were responsible for the implementation failures are identified. The future focus in such diverse areas as mineral processing, waste treatment, recycling and biosciences is discussed and the research and development needs are outlined.

Jan 1, 2003

By P. K. Sen, Mrinal K. Ghose

Tailing slurry is usually abrasive and possesses high viscosity. This paper examines the existing iron ore beneficiation process and focuses on some of the key environmental issues related to the disposal of tailings. It identifies that almost 32% of the iron ore extracted ends up as tailings and they are usually disposed in slurry form in tailing ponds. By the year 2000, 27 Mt of iron ore tailings were generated in India, which has become one of the biggest waste handling problems to the industry. Characteristics of the tailings vary widely. So the physical nature of tailings cannot be considered separately in isolation without considering the mill effluent from the beneficiation plant. In the present investigation, studies were carried out in three iron ore mines in India to evaluate the characteristics of tailings from the beneficiation plant. The tailing samples were collected from different locations during a time period of one year and analyzed. The results will be discussed and the characteristics of the tailings have been evaluated. The disposal system of tailings at the three mines was evaluated. The research on the settling characteristics of tailings indicates that the area provided in the existing tailing ponds in India is much more than that of the experimental results. This paper concludes that sedimentation tests are essential to design appropriate tailings pond with respect to size. In the proposed scheme it is suggested that an additional unit process, i.e. sedimentation tank be added to the process before the disposal of tailings to the tailing pond.

Jan 1, 2003

By D. Hatfield, G. de Jager

"The rapid developments in computer vision and computational resources are creating new possibilities for the use of machine vision systems for industrial control. A number of commercial image analysis systems exist, and research into improved measurements of froth performance is ongoing. An integral part of the implementation of these systems is the validation of the relationship between image analysis measurements and flotation cell performance. This paper discusses the factors affecting concentrate flow and presents the results obtained from one such system with respect to its ability to estimate the flow of concentrate from a flotation cell.The relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell was investigated on two industrial operations, both processing PGM (Platinum Group Metal) bearing ores. Results are presented that show a relationship between froth flow speed and concentrate yield."

Jan 1, 2003

The energy dispersion X-ray fluorescence (EDXRF) analysis technique is a rapid and accurate method for describing sample?s element component and percentage composition. On the base of profound research for the national and international development and research condition, the author researched the EDXRF analyze technique and the EDXRF analyzer?s principle in depth, the difficulties and the key points for research and development of EDXRF analyzer; gave a scheme for re-search of bench EDXRF analyzer; researched some algorithms used in energy spectrum analysis; developed the energy spectrum analysis software based on the Visual C++ 6.0; together with the energy spectrum analysis software, the author designed and processed the structural of the bench XRF analyzer and integrated the import X-ray tube, thermoelectrically cooled Si-PIN photodiode X-ray detector and pulse amplitude analyzer as a model machine. The result shows: The model machine can be used in multi-element analysis at the same time for different types of dry mineral samples, with fast analysis speed, accurate model and high stability.

Jan 1, 2014

By Xubo Chen, Zhiqiang Hu, Zhijian Sun, Gaoyun Zhou

"The research aimed at developing an efficient and environmental frother,which was applied in the flotation of sulfide ores. The flotation properties of an efficient frother and pine oil have been studied relatively by flotation tests of lead and zinc sulfide ores. At the same time, the biodegradability of two kinds of frother has been studied by the method of biological respiratory curve. The test results show that the flotation properties of new frother are superior to pine oil such as flotation rate, dosage etc. and its biodegradability is superior to pine oil. INTRODUCTION Frother is a kind of important agent in flotation reagents.In practice, the criterion of the foaming performance of the frother is what is high and low according to flotation indexes. The difference of different minerals and flotation technologies has great influence on the foaming performance of frother, and it is very important to choose the corresponding frother. The type, dosage and selectivity of frother in flotation process must be considered carefully. In today's society, environmental protection and ecological protection are becoming more and more important, and the environmental and ecological damage from mine development has aroused increasingly more attention. The use of mine agents has promoted the development of mineral resources, greatly improves the recovering utilization of mineral resources, at the same time, the production and use of mine reagents also inevitably bring about pollution, and result some influence or damage in the ecological environment.The frother is a common kind of reagent in the flotation process of the concentrator. In many cases, the waste water in the concentrator can not be let out in the natural water because the higher content of the frother in the waste water results in higher index of COD.This will inevitably increase the cost of waste water treatment in the mine.Therefore, the choice of frother should not only consider its influence on the flotation index, but also consider its influence on environmental protection. Waste water treatment is a way to solve the waste water pollution, but it needs to cost a lot of fund, manpower and material resources.And the development of high efficiency pollution-free reagent is a good way to reduce the production cost of mining enterprises and reduce the environmental pollution."

Jan 1, 2018

By T. Inoue, K. Okaya

"Movement of mill charge in the centrifugal mill is essentially different from that in the vibration mill with circular path despite the apparently similar mode in the motion of mill body. As proved e.g. in [11], this results in substantial advantage regarding the comminution intensity of the centrifugal mill over the conventional vibration mill accounting approximately to one order of magnitude.Back in 1983, Bradley et al. presented a model of the centrifugal mill based on the kinetics of the mill charge by regarding it as a lumped mass. On the other hand, numerical modeling by ‘discrete element method (DEM)’ enabled us to observe the movement of each ball in the centrifugal mill with an extremely minute time intervals (Inoue et al., XX IMPC in 1997). The former approach rendered simple, even though approximate, expression of the mill behavior, while the latter method was advantageous in describing the behavior of the mill in terms of individual events taking place in the mill body, even though the result did not reduce to a simple expression. The characteristics of the centrifugal mill described by both these approaches proved to be in a degree of agreement. Thus, the kinetic approach was capable of presenting the overall view of the mill, while the DEM model was informative of the details that could not be depicted well enough by the simple math expressions."

Jan 1, 2003

By Jim Petrie, Mary Stewart, Damien Giurco

This paper describes a generic approach to analysing the environmental and economic performance of a global mineral/metal value chain, with the express view of improving the quality of prospective decision-making within the industry in order to ensure more sustainable outcomes. The starting point for this analysis is the development of a global stocks flows and transformations model, for the metal of interest. Any aspect of the value chain, e.g. “metals refining, “goods manufacture”, “use and disposal”, can be assessed, either relative to other stages in the value chain, or in more detail by focusing on the technologies used within that stage. The use of this model as a decision support tool is explored here for the case of copper. Both primary and secondary production routes are enumerated, covering a range of processes, for seven distinct geographic regions round the globe. The value of the modelling approach is explored for different energy mixes. In particular, the case study examines the impact of increased recycling on the (re) distribution of global and regional environmental impacts for technologies-in-place in these different regions.

Jan 1, 2003

By Yu. E. Emelyanov, A. V. Bogorodsky, R. N. Nabiulin, S. V. Balikov

"The paper describes the results of the study of gold-copper flotation concentrate atmospheric oxidation at different sizes of material, varying oxidation time, with air or oxygen blow. The study showed the low rate of sulphide oxidation during oxidation of flotation concentrate at a feed size (P98 -74 µm). The coppery recovery into solution was 48%; the recovery of gold by subsequent cyanidation reached 86%. Preliminary flotation concentrate grinding to P98 -20 µm provided oxidation of 90% of copper minerals, 80% of arsenopyrite and 15% of pyrite. The gold recovery by atmospheric oxidation of a fine-ground flotation concentrate increased by 59%, from 36% to 95%, the NaCN consumption reduced by 21 kg/t, from 30 to 9 kg/t. INTRODUCTION Processing of sulphide gold-copper ores and concentrates using conventional cyanidation technology results in higher reagent consumption and lower gold recovery. Destruction of sulphide minerals and extraction of copper from a processed product prior to cyanidation is essential for improving efficiency of precious metals recovery and reducing main reagents consumption. Atmospheric oxidation (AO) is one of the most promising hydrometallurgical methods of refractory gold-copper concentrates processing, along with biooxidation and pressure oxidation. The nature of this approach lies in oxidation of sulphides at 90-95°C, in acidic or alkaline conditions, with bubbling of oxygen or air, after preliminary ultrafine grinding (1-4). The following reactions of sulphide oxidation occur during atmospheric oxidation of a gold-copper flotation concentrate. Pyrite is oxidized with the formation of ferric sulphate (1) and elemental sulphur at low temperatures (2), whereas some portion of elemental sulphur reacts to form sulphuric acid: FeS2+3,75O2+0,5H2O=0,5Fe2(SO4)3+0,5H2SO4; ?G=-1144,02 kJ/mol (1)"

Jan 1, 2018

By I. N. Gridasov, V. V. Khromov, R. I. Ismagilov

"Over 50 mln.tonne is the average annual output of oxidized ferruginous quartzites typically containing Fe38-42% mined in Mikhailovskoye ore field. The most promising and cost-effective way to expand concentrate production maintaining current output of magnetite is processing of oxidized ferruginous quartzites (hereinafter referred to as OFQ) mined as a by-product in Mikhailovsky open pit mine. However lack of proven and efficient concentration and agglomeration process applicable to OFQ and insufficient data for feasibility evaluation of OFQ processing encumbered full-scale addressing of this challenge. Based on outcomes of multiple various studies a process of OFQ flotation was designed by MC Metalloinvest LLC and PJSC Mikhailovsky GOK engineers. Comparative lab-scale testwork have proven performance and production advantages of flotation against magnetic separation feat. flotation and combined concentration method. Lab-scale flotation enabled production of concentrate with average Fe66.6% and SiO22.06% grade. Geologic and production contouring of OFQ deposited in Mikhailovskoye ore field has been carried out to collect necessary data for feasibility study incl. cost and profit estimation. As a result processing and production properties of over 3,500 samples have been analyzed which is characteristic of every direction and level of prospective ore mining within Mikhailovskoye ore field up to year 2032. Following work has been done based on geologic and production contouring of OFQ: – natural typification of ores and production (processing) grades of OFQ, determination of average mineral composition; – correlation analysis of interrelation between OFQ mineral composition and processing features thereof for overall bulk of samples as well as for individual data blocks related to various directions of open pit mine; – OFQ classification with account of defined mineral composition and processing features. Total Fe weight content in chamber product of flotation (known as concentrating ability in flotation) was applied as a major differentiating factor for processing grade classification of OFQ. Three processing grades of oxidized ferruginous quartzites were established as a result of flotation tests run to determine concentrating ability, i.e. – hard concentrated OFQ (TO) – below Fe65%; – mean concentrated OFQ (SO) – Fe65-67%; – easy concentrated OFQ (LO) – over Fe67%. Outcome of this work provided initial data for feasibility study and cost-profit evaluation of medium-term industrial-scale processing of OFQ deposited in Mikhailovskoye ore field."

Jan 1, 2018

By H. M. Yang

Structural alteration of pyrophyllite during mechanical activation in a planetary mill was investigated by X-ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR) techniques. Mechanochemical effect markedly promotes the decrease in reflection intensities with increasing the grinding time. Prolonged grinding causes the pyrophyllite to become the amorphous structure. It can be indicated that pyrophyllite is very susceptible to alteration by grinding. Crystal size (d006) of pyrophyllite appears to be a limit after 2h grinding. IR spectroscopy analysis shows a little alteration in the bands of pyrophyllite after mechanical activation. The results indicate that the ordered structure of pyrophyllite is destroyed and lattice deformation occurs. Porous silica was then successfully prepared via leaching the mechanically activated pyrophyllite. Pyrophyllite was first ground for 6 h. Ground samples were subsequently leached with 4 M hy-drochloric acid at 80 °C for 2 h to produce porous silica with specific surface area of 188.1 m2/g, total pore volume of 0.18 mL/g and average pore size of 3.9 nm from N2 adsorption analysis. Otherwise, the porous silica obtained from direct leaching of the original pyrophyllite only has a specific surface area of 4.3 m adsorption analysis. 2/g and total pore volume of 0.03 mL/g. It is inferred that grinding is favorable for the formation of microstructure pores. It offers a simple and convenient route for the preparation of porous materials from natural minerals.

Jan 1, 2014

By P. K. Rozakeas

It has been experimentally demonstrated that the application of electrokinetic techniques in the continuous flow of coal-water suspensions within a helical anode-cathode pipe geometry effectively causes a significant reduction in the wall shear stress. This reduction in the frictional force at the cathodic pipe wall surface is attributed to a decrease in the concentration of coal particles in this flow region caused by the migration of negatively charged coal particles towards the anodic surface(s). The disadvantage of flow-intrusive geometries is the reduction in effective flow area as well as an increase in frictional surface area caused by the placement of the anode(s) within the flow region. Experimental data is presented for a non-intrusive helical anode-cathode geometry embedded in the pipe wall which shows that a reduction in pumping energy of approximately an order of magnitude is possible. A sample of sub-bituminous black coal fines having a mean particle size of approximately 17 microns was used to prepare coal-water suspensions with a solids concentration of 50%(w/w). The practical and economic implications of this work relate to an enhanced method of long distance transportation of slurries in pipes as well as an alternative technique for continuously separating solid-liquid suspensions.

Jan 1, 2014

By M. Wierink

The lifecycle of a resource, specifically a metal, is often depicted as circle from primary production from mining to minerals processing and via manufacturing and use to disposal and recycling. When a material is recycled, it is considered as saved energy compared to producing the material from primary source. This is, however, a simplified representation. At each step of the life cycle, there are changes in the quality of the material due to different materials chemical and physical interaction, phase transformations due to diffusion, radiation etc. Due to these physical and chemical phenomena there are losses of material, which as determined by thermodynamics are not recoverable within the life cycle. This can be considered as an increase embodied energy per mass unit of substance and loss exergy from the material cycle. With low cyclic loss, the material will remain in the recycling loop for a long time, while with high cyclic loss it will disappear fast. Where you put the material determines how fast it disappears from the resource cycle. In this research paper the phenomena of quality degradation of material and idea of increase of embodied energy and exergy loss within a resource cycles is portrayed. The cyclic nature of material states and transitions and energy consequences of material quality degradation as well as the parameters affecting the length of the time scales of the material cycles are described. Currently the cyclic embedded energy and the history of material is not taken under consideration in generic life cycle assessment. This easily results into a conclusion that lifetime of product is optimized only in terms of how much energy an appliance uses during its lifetime, while ignoring the loss of embedded energy due to the effects caused by the environs the material is subjected to during the cycle. Better description of the time properties of material give us a possibility to design toward optimum lifetime of products in terms of resource efficiency. Keywords: product lifetime, material lifetime, recycling, cyclic resource efficiency, material state, material quality, exergy, embodied energy

Sep 1, 2012

"The research aimed at solving the problem of measuring instantaneous local physical quantities for multiphase flows in mineral processing, which are common in minerals industry and with significant challenges. Due to the lack of proper measurement tools currently in minerals industry, multiphase flows (such as in flotation cell) are treated as in a “black-box”. It is crucial to develop measurement technique by which the acquired processing data can be used for process optimization and control. By measuring the conductivity distribution across a measurement area, Electrical Resistance Tomography (ERT) has been adopted by many researchers to monitor and investigate many processes involving multiphase flows in other industry sectors. A compact ERT probe was built and then used to measure the conductivity distribution within a few flotation machines. In a flowing foam flotation column, the results showed that ERT can accurately measure the change of liquid content (high conductivity fluid distribution). In another part of work, based on the Green-Kubo relations, ERT can measure turbulence via the fluctuation of conductivity caused by bubbles moving through the measurement area, changing the density of the fluid. The tests with the Metso 3 m3 RCS flotation cell were also carried out for turbulence measurement under different air rates and impeller speeds. The results of flotation cell from ERT measurement showed that varying impeller speed had more pronounced influence than changing air rate. When impeller speed is increased, the size of the high turbulent zone increases. ERT is a powerful technique that has the potential to be used for a wider range of applications. The future work will be carried out with more case studies and expanded to more processes such as leaching process, high temperature flows in further downstream production chain (steel making process and alloy manufacturing process).INTRODUCTIONMultiphase flows constitute a majority of the naturally-occurring and industrially-relevant flows, especially in mineral processing. Some of the measurement techniques have been used for the study of fluid characteristics. Optical techniques such as Laser Doppler Anemometry (Kyselaa et al., 2013) and Particle Image Velocimetry (Nobach and Bodenschatz, 2009) can produce accurate measurement results with high spatial and temporal resolution, but their applications are limited to transparent flows. Hot wire probes (Amini et al., 2013) have high spatial and temporal resolution in turbulence quantification, but they are susceptible to environmental factors."

Jan 1, 2018

By Vishal Shukla, Ashok Kumar, C. Raghu Kumar, D. P. Chakraborty

"Traditional iron ore beneficiation plants using washing, screening, and jigging processes require large volumes of process water. Generated slime during processing, its disposal and impact on water usage, is an important concern for any mining company. The challenge today, during extracting iron ore, is how to dispose of slime such that it is contained and stable, while maximizing water reuse and minimizing surface footprint. The slime disposal methods are sensitive to the environment. Two major technologies presently being practiced for disposing the slime across the world are pressure filtration and paste thickening. In this perspective an attempt has been made to do comparative study between paste thickening and pressure filtration for selection of suitable slime disposable technology for Noamundi processing plant, Tata Steel. From the studies, it is evident that by adopting pressure filtration technique it was possible to produce filtered slime, whereas filtration, rate reduces significantly with the presence of finer fraction. Further , the greatest advantage of paste thickening is volume reduction of slime. By considering the technology limitation and comparative lab test work result, it is opined that combination of filtration and paste thickening technology is favorable in terms of capital and operating cost and slime >45 µ should be filtered and < 45 µ slime should go for paste thickening. The study and the results are presented in details.INTRODUCTION The beneficiation processes always end up with an enriched portion of desired mineral - “Concentrate” and an enriched portion of undesired minerals - “Tailing”. The proportion and nature of tailings generated in every beneficiation process differ from ore to ore and reflects the characteristics of the feed processed. The traditional method of tailing disposal in many mineral processing industries has been to dispose them as thickener underflow at around 35% solids. Though, it had certain advantages of transportation with ease but contribute to a greater volume occupied in the tailing dam. This sustained practice and failure to utilize the space available in the tailing dam judiciously endangered the mining industry. The tailing management has become the toughest task to the mining industry and most of the mines are running out of space for disposing the fresh tailings as many of these are at the verge of getting filled."

Jan 1, 2018

By A. M. Raichur, S. P. Vijayalakshmi

Fine coal dewatering is a major problem in the coal industry because the fines hold significant amounts of water and account for two-thirds of the product surface moisture. Present methods include flocculation using polymeric flocculants followed by filtration. But the kinetics of filtration are not favorable with such flocculants. In this study, a novel method involving flocculation with microorganisms for improving the settling rates and dewatering kinetics has been investigated. Two Gram-positive microorganisms, Mycobacterium phlei and Bacillus subtilis were used as bioflocculants. The effect of time, pH and ionic strength of the electrolyte used on adhesion and flocculation were studied. Adhesion tests showed that maximum adsorption occurred in 20 minutes in the pH range of 2-7 and the total amount of bacteria adsorbed was almost the same with both the flocculants. Nearly 98% of the coal flocculated with both the microorganisms in about 5 minutes. The filtration rate of fine coal almost doubled with addition of bacteria and electrolyte and maximum filtration occurred near the point-of-zero-charge of the bacteria.

Jan 1, 2003

By P. T. Nguyen

The analysis of particle capture by an air bubble by two separate phenomena of collision and attachment has been difficult due to the uncertainty in determining when and where the two phenomena begin and terminate at the bubble surface, respectively. Therefore, a unified analysis was developed by solving the motion equation for the particle capture as one process. No distinction be-tween collision and attachment was made. Both the liquid film described by the micro-hydrodynamic resistance functions and the surface forces were included in the new model. The model predictions with the DLVO (Derjaguin-Landau-Verwey-Overbeek) surface forces did not agree with the experimental trajectories of latex and silica spheres. The model predictions with the inclusion of the non-DLVO attractive surface force agreed with the experimental data. The non-DLVO force reduced the repulsion between the non-attaching particle and the bubble, and significantly increased the attraction between the attaching particle and the bubble. The unified analysis is capable of predicting particle capture without the use of the induction time. The unified analysis also shows significant influence of the short-range hydrodynamic interactions on the collision which has been previously ignored.

Jan 1, 2014

By R. K. Dwari

The electrostatic beneficiation of coal is based on tribocharging characteristics of ash forming minerals and coal particles. The tribocharging of quartz, pyrite and coal particles contacted with various metals and polymeric materials have been measured and the charge acquisition is assessed through surface energy calculations from liquid contact angle data. The contact angles, before and after tribocharging of solids, are measured using Krüss tensiometer and Washburn?s method where the sample holders in tensiometer are specially constructed with tribocharger materials. The charge polarity and amount of charge acquired by quartz, pyrite and carbon with metal tribochargers were found in good agreement with the reported work functions of the contacting surfaces. The charge results with polymer materials differed from the work function values, presumably caused by surface contamination. The surface energy of quartz calculated by all the theoretical approaches in the literature showed that the tribocharging increases the surface energy. Both polar and non-polar components computed from Fowkes and Owens-Wendt-Rabel-Kaelble approaches dis-play that both these components increased after triboelectrification. However, the polar component divided into acid and base components, as in van Oss approach, manifest decreasing acid part and increasing base part. Since quartz charged negatively during tribocharging with metal surfaces and therefore accepted electrons, the determined acid and base surface energy components are consistent with charge transfer process. The results also elucidate an explicit correlation between the charges generated by powders and the surface acceptor (acid) and donor (base) electronic states and thereby the work functions. A novel fluidized bed tribocharger was designed and developed with internal baffle system for efficient contact electrification of mineral and maceral to produce high differential charging for efficient separation. The results achieved on coal with 45% ash content are presented and discussed.

Jan 1, 2014

By Tom Liu

This paper is a fundamental study of bubble-particle collision efficiency in turbulent flows. A CFD-based microscale scheme for the prediction of turbulent bubble-particle collision efficiency in a 3D isotropic turbulent flow is developed, and in this way, turbulence effects on particle-bubble collision efficiency are taken into account for the first time. By comparing the computed results with experimental data from the literature, the CFD simulation is shown to correctly predict the bubble-particle collision efficiency in a quiescent environment. The CFD method was then applied to the investigation of bubble-particle collision efficiency in a turbulent flow, and the simulation results are shown to be qualitatively consistent with the real observations. The predicted collision efficiency can be used in a multiscale modelling scheme, which would account for all control variables in a flotation cell, such as impeller structure and tip speed, air nozzle structure and air flow rate This study indicates how microscale simulations of bubble and particle behaviours, coupled to macroscale CFD simulations of flotation cells, can provide a powerful tool predicting the flotation rate in a real flotation cell.

Jan 1, 2014