Search Documents

By S. M. Bradshaw, R. Smith, J. H. van Vreden, C. A. Snyders

"The re-treatment of gold tailing heaps has shown to be a potentially significant revenue stream for both large and small scale gold companies. Limited access to capital and lack of skilled labour remain restrictive especially when dealing with a refractory ore and/or where limited amount of material are available. Alternative techniques such as low temperature pre-leaching options to unlock value are therefore in demand. Several low temperature pre-leaching experiments in acidic and alkaline solutions, followed by cyanidation were performed which ultimately led to the further investigation of a caustic pre-leaching step. It was found that the Au recovery from a refractory ore tailings heap could be significantly improved from ˜ 15 to 20% to greater than 60% with a simple atmospheric NaOH pre-leaching step. It was further considered, that since the NaOH pre-leach liberate the Au associated with refractory sulphide minerals, the overall process may benefit by the inclusion of a froth flotation step to separate refractory sulphides from the free milling ore. Froth flotation on weathered tailing heaps are, however, known to be difficult, ultimately resulting in poor recoveries. A process flow sheet, incorporating a caustic pre-leaching step and a process which includes flotation and caustic pre-leaching of the concentrate, are technically evaluated and ultimately compared to simple cyanide re-processing. INTRODUCTION South Africa consists of a large number of gold tailings dumps. Janse van Rensburg (2016) estimated that there was about 517 dumps in the Gauteng area, covering approximately 320 000 ha of surface area. Recovering value from the dumps has received a great deal of interest but can be problematic due to the dumps often being refractory, preg-robbing and weathered. High recovery of valuable metals (Au and Ag) are possible (Fleming and Brown, 2010) but would most likely require pressure oxidation and subsequent neutralisation which can be very capital intensive demanding a high skill set to operate and maintain. In addition, these flowsheets target high processing tonnages due to the economy of scales at the lower grade feed materials, further increasing the capital requirement."

Jan 1, 2018

By C. L. Tang

Parts of the wastewater are reused directly and the rest moderately purified and reused, so the utilization rate of wastewater of the whole processing plant reaches 100 percent. At the same time, beneficiation indicators have been improved stably, and great economic and social benefits have been achieved.

Jan 1, 2014

By Jonas Addai-Mensah

Despite the fact that nickel (Ni) laterites accounts for about 60 % of the world?s nickel mineralization, commercial processing of complex, low grade Ni laterite ores by conventional beneficiation (e.g. magnetic, electrostatic and flotation separation) still presents intractable challenges, particularly in heap leaching. Invariably, low grade laterite ores require aggressive hydrometallurgical techniques (e.g., highly acidic lixiviant leaching at ambient or elevated temperatures) for Ni and cobalt (Co) extraction. As a precursor to heap leaching, agglomeration of the multi-mineral phase feed particles into robust and porous granules of 4-10 m permeable bed, is essential. In the present work, several basic and applied studies of the agglomeration behavior of real Ni laterite ores and selected oxides and clay minerals (hematite, quartz smectite and kaolinite) which constitute the predominant host gangue phases of typical laterite ores are performed. Isothermal, batch agglomeration tests involving sulphuric acid solution as a binder were carried out to produce coarse, narrow-sized (5 ? 40 mm) granules which were well characterized. The influential role of feed ore characteristics (e.g., mineralogy/chemistry and primary particle size distribution) and binder composition (30 vs. 44% w/w H2SO4) and dosage (15-25 wt.%) in agglomeration behavior and granule properties were examined through several characterization techniques including granule size, compressive strength, bed percolation and re-wetting stability and 3-dimensional micro-structure analyses. Links between feed mineralogy/chemistry and size, binder formulation, agglomeration behavior, curing conditions and final granule properties and structural characteristics are established. The implications of the findings to Ni laterite plant agglomeration for enhanced heap leaching are discussed. Keywords: nickel laterite, complex low-grade ores, agglomeration, heap leaching, micro-structure

Sep 1, 2012

By A. Usov

The studies carried out by the Russian researchers and those carried out jointly within some contracts with scientific organizations and companies of other countries, show that the electric pulse disintegration of materials (ED), proposed and investigated in detail in Russia (Kalyatsky, et al, 1980; Usov et al, 1987; Semkin et al, 1995; Usov and Tsukerman, 2000; Kurets et al, 2002) has been widely recognized and developed abroad (Andres, 1995; Inoue et al, 2000; Biela et al, 2008). The Russian and international journals and the proceedings of the conferences dealing with the electric pulse disintegration pay great attention to the principal principals of selective disintegration of materials. There is no, however, any information concerning both the technical means developed to implement the technique and the assessment of their performance, which would be necessary in objective assessment of the industrial use of the technology. The results of long-term studies of the technique and technologies of electric pulse disaggregation by research institutes such as Research Institute of High Voltages (Tomsk), Kola Science Centre of RAS (Apatity), Institute "Mekhanobr"(S.Pertersburg) described. Exploratory stands and technological installations are developed to carry out pilot tests and operations under production conditions. Basic circuits and classification of technical means electric pulse disintegration of the materials are proposed, the analysis of transportation schemes and classification of the material in the disintegration apparatus are given, construction of chambers for continuous stadial disintegration of ores and materials are presented. The features and technological efficiency of electric pulse disintegration of various types of ores, and the spheres of effective use of the method have been determined. Keywords: electropulse disintegration, disintegration machines, chambers of comminution, stadial comminution.

Sep 1, 2012

By B. Q. By

TiO2 is an ideal material for catalytic technology due to its unique properties. In this paper, Sm3+ doped TiO2 photo-catalyst was developed to improve the efficiency of TiO2 and to use the natural light as irradiation source, which was made from Titanium Tetrabutoxide and Samarium Oxide with the Sol-Gel process. The Sm3+-TiO2 photocatalyst was used to degrade reactive orange 4 (RO4) in Azo Dyes. The effects of solution pH, Sm3+ concentration and catalytic time on the degradation rate of RO4 were studied. The characteristics of the catalyst were analyzed with XRD and TEM. The experimental results show that the catalyst has high activity in the degradation of RO4. The Azo bonds of RO4 are active and easily broken by oxidation. The catalytic activity of the Sm3+ doped catalyst greatly depends on the pH of solution. The catalyst has high photo-catalytic activity at both neutral and alkaline conditions. The degradation mechanism of the Sm3+ doped TiO2 photo-catalyst was also discussed.

Jan 1, 2014

By I. S. M. K. Ilankoon

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behavior is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. Previous modeling of this system has used equations from oil and ground water flow to model these systems, but the applicability of these models with the larger particles found in typical heaps is suspect as these systems are not necessarily capillary dominated. In particular, as the characteristic particle size goes from below to above a few centimeters, the flow changes from capillary to gravity dominated. This means that typical heap leaching heaps cover this interesting, but complex, transitional fluid flow regime. In this paper a set of experimental studies of this flow, including PEPT (positron emission particle tracking) based tracer experiments, highly accurate liquid holdup measurements and axial dispersion experiments using salt tracers will be presented. In this study, flow through mono-dispersed particle beds was carried out. In particular, the hysteresis in the liquid holdup as the liquid flow rate into the particle bed is varied is investigated, since this hysteresis means that the relationship between flow rate and holdup is history dependent, an effect not included in models currently used to describe fluid flow in heaps. A theoretical model that describes this hysteresis will also be presented. Keywords: heap leaching, hydrometallurgy, modeling

Sep 1, 2012

By G. Demi, G. Belardi, N. Shehu, S. Cico

The physico-chemical interaction between minerals such as olivine, chromite and serpentine and the ions most commonly present in solution, like Ca and Mg and flotation reagents such as EDTA and oleic acid was investigated. The study was conducted via release tests, electrophoretic measurements and microflotation of selected minerals coming from the Kukes deposit (Albania). The results were confirmed by means of beneficiation tests on various types of ores, from the Kukes (Kalimash), from Bulquiza area and from the Rizo deposit (Greece). It has been demonstrated that when Na-K Oleate is used as collector chromite, olivine and serpentine can be separated at pH = 2.5 and/or 5.5 employing EDTA (EthyleneDiamineTetraAcetate) on previously deslimed material. This approach ensures flotation concentrates with a Cr2O3 content about 50%, at a recovery in excess of 65%.

Jan 1, 2003

By Susanna G. de Jager, Francis W. Petersen

"The aim of the project was to develop a methodology applicable to different South African coal types to be able to predict with a high degree of certainty what kind of reagent will be suitable for flotation of a certain coal type.The study included 5 coal samples from different collieries and included Highveld seam 3 and 4 coal (as one sample), Waterberg coal (zone 10 -11), Highveld seam 5 upper coal and Witbank seam 2 and seam 4 coal. Seam 3 and 4 (mixture) coal, Waterberg and the seam 5 upper coal were all found to be vitrinite rich coals. The coal characterisation study included petrographic analysis, proximate analysis, float-sink analysis, oxygen-containing functional groups, surface extraction, flotation release analysis and contact angle measurements.The flotation tests showed that the best reagents to float all of the coal samples studied are iso-decanol and dodecene. These reagents produced flotation products that are near to the release curve. Statistical relationship for predicting ash content and yield that can be expected for a certain coal type and selected collector was obtained. From the relationship, the accuracy of the yield is above 95% (p-value below 0.05) with a linear regression of 0.9289. The accuracy of the ash is slightly lower with a linear regression of 0.7841 but also above 95%."

Jan 1, 2003

By F. Göktepe

Flotation gases and conditioning of the pulp with them are one of the important parameters of flotation and should be taken into account especially in the flotation of sulphide ores. In this study, flotation of pure chalcopyrite and pyrite samples were investigated with air, oxygen and nitrogen as flotation gas and the effect of conditioning with these three gases also were performed. Flotation gas was introduced for 5min, 10min, 15min and 20 min. For chalcopyrite flotation there was no drastic change in recovery when air, oxygen and nitrogen were used as flotation gas but conditioning the pulp with oxygen for 10 minutes increased the recovery about 8% where pulp potential has been approximately 25 mV with chalcopyrite and 150 mV with platinum electrodes. Conditioning with all three gases decreased the pyrite recovery by about 20% with 20 minutes conditioning. Pulp potential decreased in the presence of nitrogen while conditioning with air and oxygen increased the pulp potential for both electrodes. Generally potential increased for both minerals with oxygenation and aeration time but it was stable or slightly decreased with nitrogenation. Comparison of the gases showed that the different flotation gases do not effect flotation recovery but conditioning the pulp with these gases at pre-flotation effects chalcopyrite and pyrite flotation recovery, most dramatically pyrite.

Jan 1, 2014

By L. C. Zhou

The floatability of andalusite and associated minerals are studied and their action mechanisms of andalusite and associated minerals with collector alkyl benzene sulphonate are also studied. Through the mensuration of electrical potential and the infrared spectroscopy, as well as desorption tests, it is confirmed that the interaction of andalusite with sodium dodecyl benzene sulphonate (SDBS), is in addition to physical adsorption, but also is chemical adsorption. The study results of the pure minerals are used for the flotation of actual andalusite mineral. By flotation from contain-ing 45.68% andalusite ore, the fine andalusite concentrate is gained which Andalusite grade is 85.88%, containing Al2O355.29% and Fe2O3 less than 1.5%.

Jan 1, 2014

By Zofia Swierczek

This paper reports the results of a detailed mineralogical study of typical, low-grade Australian nickel laterite run-of-mine ores. Successful development of an effective beneficiation process for upgrading such low grade laterite ores relies on good knowledge of the laterite mineralogy and the value metal(s)? distribution characteristics. Both QEMSCAN and quantitative X-ray diffraction techniques were used to conduct the mineralogical analysis of three types of laterite ores, and the results were compared with those obtained by chemical analysis. Some of the major challenges faced included accounting for the mismatch between the nickel values measured by QEMSCAN and those recorded by chemical analysis. This was primarily due to the relatively low concentration of nickel in the ores and its wide dissemination among several major host minerals in complex association. Careful analysis showed that the limit of nickel detection in iron oxide host mineral grains under normal operating conditions was around 4%. Keywords: nickel laterites, mineralogy, characterisation, QXRD, QEMSCAN

Sep 1, 2012

By S. Kelebek, A. Khan, J. Caceres, Beckett. D.

"Pyrrhotite in nickel-copper sulphide ores is nickeliferrous and intimately associated with pentlandite. Due to its low nickel content, pyrrhotite rejection is an important step in processing of these ores. In our laboratory, various reagents were investigated for their effect on pyrrhotite depression. Among these, a combined use of triethylenetetramine and sodium metabisulphite was found highly promising.The work described in this paper has two parts. The firs part is a summary of results obtained on process samples from the pyrrhotite rejection circuit at Falconbridge’s Strathcona Mill. The second part involves simulation of the circuit performance based on the reagent conditions used in the experimental work and the concept of split factors.Two sets of reagent conditions were evaluated. The first one involved baseline conditions, simulating the current reagent performance. The second one simulated the impact these new reagents can have on the circuit performance.The simulation results obtained under baseline conditions indicated a good agreement with the current circuit performance. The simulation results suggest that at practically the same pentlandite recovery and tailing grades, the circuit concentrate nickel grade can be doubled through effective pyrrhotite rejection by these new reagents."

Jan 1, 2003

By V. Runkana, N. K. V. Nadimpalli, S. Sahu

"IsaMill™ has been in operation in the recent past for fine grinding of low grade ores to extract non-ferrous minerals. IsaMill™, typically, consists of a series of uniformly spaced identical disks mounted on a rotating shaft which is encased in an outer shell. The mill offers high energy efficiency for fine grinding and an inherent scalability. But, it encounters certain operational challenges such as non-uniform distribution of grinding media coupled with high wear rate of the disks and solid walls of the mill at specific locations—which adversely affect the mill performance. To circumvent these operational challenges, design modification of the disks through heuristics, by introducing a reduced diameter disk (RDD) at specific locations, is a common practice in industry. But there is no systematic scientific study in this regard. In the current work, we developed a discrete element method (DEM) based model and simulated for the IsaMill™ operation to study the effect of RDD on the efficiency of the mill and wear rate of the solid walls and disks. Since the first set of disks experience the high wear rate due to the high loading of the charge, the RDD was introduced at the first two disks. The simulations were performed at different diameters of the RDDs and at different media loadings. The performance of the mill was analyzed based on the power consumption, the wear rate on disks and the distribution of media particles inside the mill. Besides, the performance variables such as mean velocity of media particles and total impact energy provided useful insights into the milling operation. It was observed that the reduction in disk diameter yields lower wear rate of the disks at the cost of decrease in power draw at a constant high media loading. Whereas, when the media loading was decreased, the amount of wear and power drawn was comparable for both the most reduced and least reduced disk diameters. Therefore, there is an optimum choice of RDD for a given mill loading to maximize the mill performance while reducing the wear rate of the disks."

Jan 1, 2018

By K. Amano, K. Haga, Y. Watanabe, A. Shibayama, A. Batnasan, A. Battsengel

"Apatite is an important host mineral in igneous and metamorphic rocks for production of phosphate fertilizers and phosphoric acid, and a potential source of rare earth elements (REE) production. For dissolution of REEs, sulfuric acid is better leaching reagent to develop the economical viable process for recovering of rare earth elements from apatite ore. However, the efficiency of rare earth elements dissolution in H2SO4 is about 30 % due to the formation of calcium phosphate or calcium sulfate as precipitate. On the other hands, phosphorus is mainly produced from phosphate ore. However, when treating rare earth elements containing phosphate ore, rare earth elements were discharged. Hence, development of novel apatite ore treatment process is required for effective utilization of natural resources. In this study, apatite deposit associated with REE was treated with sulfuric acid leaching and two stage precipitation by oxalic acid (C2H2O4) and magnesium chloride (MgCl2) for recovering REE and phosphorus, individually. Results showed that it can be seen the vast majority of La (87.5%), Ce (87.3 %), Pr (86.1 %), Nd (85.2 %) and Y (90.9 %) were dissolved in 1 mol/L diluted H2SO4 solution from the apatite ore. As average leaching rate of REE, over 85% of REE were leached by the condition. In the first stage precipitation using the obtained pregnant leach solution from leaching, over 90% of REE was precipitated by oxalic acid addition after controlling pH to 1 by NH4OH solution. After pH changed to 8.5, over 90% of phosphorus was recovered as precipitate by magnesium chloride addition in second stage precipitation"

Jan 1, 2018

By V. A. Ivanova, T. N. Perunkova, N. O. Dorozhanova, G. V. Mitrofanova

"Oxyethylated compounds are used as reagents-regulators in the flotation of non-sulfide ores, in particular, apatite-containing ores. Thus, the necessary degree of selectivity in the flotation separation of two calcium-containing minerals of apatite and calcite is achieved only by using, in addition to a collector, regulators-reagents from the nonylphenol ethoxylates class. In order to establish the most optimal structures, this paper presents a comparative assessment of the physical-chemical and flotation properties of several classes of oxyethylated compounds - alkylphenol ethoxylates, aliphatic alcohol ethoxylates and oxyethylated carboxylic acid. The authors have studied their dispergating ability with respect to the air phase and calcium soaps of the carboxylic collector. Dependences of foaming properties of regulators on the degree of oxyethylation have been determined. Adsorption isotherms of sodium oleate on apatite and calcite in the presence of regulators have been obtained. It has been shown that the presence of oxyethylated compounds in the solution reduces the amount of the adsorbed fatty acid collector. The influence of the considered classes of regulators on apatite flotation has been studied. The interrelation of flotation properties of oxyethylated compounds and their molecular structure has been established.INTRODUCTION Flotation plays a leading role in complex apatite-containing ores processing. However, two calcium-containing minerals - apatite and calcite, which compose apatite-carbonate ores, are characterized by close flotation properties. Selective separation of these minerals is a difficult task, the solution of which is impossible without using reagents-regulators. One of the ways to ensure the selectivity of the flotation separation of calcium-containing minerals is the use of reagents-depressants such as sodium silicate, starch, cellulose derivatives, and others (Liu et al., 2016; Rao et al., 1989). Another method is the application of nonionic reagent regulators (Filippov et al., 2016; Filippova et al., 2014; Ignatkina, 2017), which contribute to the adsorption of the ion collector (Filippov and Filipova, 2006 Rao and Forssberg, 1997) and stability of formed froth (Sis and Chander, 2003)."

Jan 1, 2018

By Z. G. Song

As a kind of complex physicochemical process, grinding would affect the subsequent mineral processing such as flotation considerably. In this study, the effect of wet grinding on malachite and calcite flotation using sodium oleate as collector was studied. And the mechanism of the effect of grinding was investigated. Laboratory scale grinding and flotation testing of malachite and calcite samples were performed. Different grinding media were used, including steel balls and zirconia balls. It was the aim of this work to study the effect of grinding on the pulp chemistry paying particular attention to flotation recovery. The effect of grinding media and different addition location of sodium oleate on malachite and calcite flotation was studied. The methodology used in this project involved grinding the ore with and without the addition of sodium oleate in mill, measuring the pH and metal ions produced by minerals after grinding, adding various quantities of sodium oleate and determining the copper recovery. The presence of species of products on the minerals after grinding was probed using X-ray photoelectron spectroscopy (XPS), and the metal ions produced by minerals after grinding were measured by atomic absorption spectrometry (AAS). It is showed that the mil-ling environments evaluated significantly affected the flotation of malachite and calcite. This study also discusses the effecting mechanism of grinding environment on floatability of malachite and calcite.

Jan 1, 2014

By Venkataramana Runkana, Aditya Pareek, Vishnu Masampally, Nagaravi Kumar Varma Nadimpalli

"Recovery and grade of the ore produced are two important metrics, which define the profitability of a mineral processing plant. Achieving high grade and high recovery at the same time in a mineral processing plant is difficult due to conflicting nature of the two objectives. To explore the operability limits of the plant operations and find the set of operating conditions that can help achieve the best possible recovery and grade, there is a need to solve a multi-objective optimization (MOO) problem. Past research focused on building a plant-wide simulation model or on optimization of individual units or a part of a mineral processing plant like grinding circuit, crushing circuit, etc. However, it is necessary to consider optimization of the complete plant in order to optimize the plant performance. Here, we have formulated the mineral processing plant performance optimization as a MOO problem. We have applied machine-learning algorithms such as random forest to build models to predict the recovery and grade of the ore. A non-dominated sorting-based multi-objective evolutionary algorithm called NSGA-II (Non-dominated Sorting Genetic Algorithm II) was employed to solve the MOO problem. Since the number of parameters that influence recovery and grade are quite large, we have applied machine-learning algorithms for feature selection or identification of key process variables. Pareto optimal conditions were determined for manipulated variables like grinding mill throughput, speed ratio at SAG mill, speed of centrifugal pump, water addition at different locations etc. The results obtained are useful in identifying the operability of a mineral processing plant to achieve the optimum grade and recovery for a given feed grade and the processing circuit. INTRODUCTION Copper is majorly mined or extracted as copper sulfides from large open pit mines in porphyry copper deposits. Among all the available ores, sulfides are the most commercial ores, especially chalcopyrite (Greenwood and Alan, 1997). Copper grade in these ores generally lies between 0.4 to 1.0%. In order to perform smelting operation, the grade of copper has to be improved to around 30% (Biswas et al. 2013). This targeted copper grade is achieved through two stages of mineral processing. Firstly, the copper in the ore has to be liberated by crushing the mineral rock. Secondly, the liberated copper in the crushed ore is then physically separated from other minerals like nickel by froth flotation techniques."

Jan 1, 2018

By B. K. Mohapatra

Small manganese ore bodies in south Odisha, India occurs both as stratiform and stratabound ore bodies. These two ore bodies show contrasting mineralogical, petrographical and chemical characteristics. Stratiform type of Mn-ores consists of manganese, iron and silicate- phases in approximately same proportion. In contrast, stratabound ore bodies contain a high proportion of manganese oxides, silicates and phosphorus phases. Phosphorus is found within apatite in the stratabound ore bodies while in the stratiform ore it occurs as an adsorbed state with iron phase (goethite). Both ore bodies are low-grade (17-23% Mn) therefore do not have a market value. However, the stratabound ores are enriched in phosphorus (P2O5: >1%) compared to the stratiform ores. Both the ore types were processed through gravity, magnetic and roast reduction followed by magnetic separation techniques. The strata bound ore could be upgraded to 33% Mn from a feed of 23% by combination of dry and wet magnetic separation methods. But the phosphorus content also suits up (P2O5: 1.2%) in the processed product making it unsuitable for further use. The stratiform ores do not respond to either gravity or magnetic separation because of close association of manganese with iron phases. However, this could be beneficiated through roast reduction followed by magnetic separation. An ore with 17% Mn content could be upgraded to 40% Mn with a 42% yield and 78% recovery. The goethite, having phosphorus, converts to magnetite and is retained within the magnetic fraction, thereby reducing the concentration of phosphorus in the non-magnetic fraction, which becomes the product. This report demonstrates the influence of ore petrology in determining the up-gradational potential of manganese ore in the southern Odisha, India. Keywords: manganese ore, physical beneficiation, phosphorus rich ore

Sep 1, 2012

By Irena Grigorova, Tashka Ignatova, Ivan Nishkov, Andrian Valchev

"Feldspars used by ceramic and glass industries as fluxing agents are mainly obtained from high quality feldspar deposits. The demand for feldspar as raw material for industrial applications especially in ceramic manufactures is continuously increasing. However, due to the depletion of those deposits, the research activities related to the recovery of feldspar from the lower grade feldspar deposits and feldspar bearing rocks such as pegmatite, granite, arkosic sandstone and syenite have been intensified in the last two decade. In Bulgaria, the main deposit of arkosic sandstone is located in the area of Shumen town, NE Bulgaria. In Srednya deposit arkosic sandstones are found in Upper Cretaceous sediments (Santonian). In this formation, there are two major industrial minerals - feldspar and quartz. They may be of economic value and possibly suitable for commercial uses. The main purpose of the present study was to investigate the beneficiation and upgrading processes of Srednya deposit arkosic sandstones. In a laboratory scale it was studied the possibility to obtain the feldspar concentrate and quartz sand from arkosic sandstones. Particle size distribution, chemical and mineralogical compositions of quartz-feldspar sands were determined. The bench-scale tests using the KOALIN AD laboratory experimental facilities were conducted. Many processing techniques were tested: disintegration, washing, sizing, carbonate flotation and feldspar flotation. The experimental results show that there are possibilities to obtain the silica sand with low content of Fe2O3 - below 0.02 % and potassium feldspar with content of K2O > 14 %. A new technology for recovery of feldspar and silica sand from arkosic sandstone was developed."

Jan 1, 2014

By Leonardo Soto, Fernando Villanueva

"Antofagasta Minerals S.A. (AMSA), for its Centinela District Project, is currently developing, at a first stage, a new 90 ktpd Concentrator Plant incorporating Esperanza Sur (ESP Sur) and Encuentro (ENC) ores. In order to dimension properly main equipment, specifically for grinding circuit, a final decision has been taken using geological and metallurgical (comminution) data from both body ores. Data was analyzed internally within AMSA and its consultants to get a final proposed circuit for further engineering studies. Specific Energy Consumption (SEC) parameter is one of the main key factors for proper dimensioning. To get an accurate value different tests have been made and modelled to ESP Sur and ENC ores. Also, operational data from Esperanza operation has been taken into account due to its similar ore characteristics to ESP Sur ore and incorporated as input data for design. Depending on data, quality and amount, it is possible to estimate accuracy for project investment and risk level, hence investment decision can be taken under good and reliable information."

Jan 1, 2014