Search Documents

By M. T. Davisson

Pile compression load capacity prediction methods are divided into four categories for purposes of discussing their reliability compared to static load test results. The categories considered are: 1) static analysis, 2) driving formulas, 3) wave equation analysis, and 4) dynamic measurement and analysis. It is concluded that any method of static analysis that works for the geological deposit in question may be satisfactory. However, any given method can be quite wrong when applied to other deposits of soil that are different in terms of their engineering and geological characteristics. Dynamic formulas are found to be theoretically unjustifiable. The ready availability of the wave equation analysis for microcomputers eliminates the need to utilize dynamic formulas. The wave equation analysis is found to be the best analytical method for making predictions both for design and for construction control. Dynamic methods of measurement and analysis are found useful, but have limitations that have caused troubles on many projects. Two case histories are presented that show the limitations of dynamic measurement and analysis, and of the wave equation analysis. Soil deposits exist that defeat both the wave equation and dynamic measurement techniques; static load tests are currently the only method of proving the load capacity of piles in such soils.

Jan 1, 1991

By Arturo Ressi di Cervia

Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 feet diameter drilled shafts with 7.5 feet rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at each the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts.

Jan 1, 2003

By Michel Bustamante

The occasional substandard performances of continuous flight auger in particular soil conditions have prompted the drilling rig manufacturer to improve the standard CFA in order to reduce its negative effects. A real improvement of interest was the launching of the double rotary CFA system. The promising features of the latter have incited the authors to implement an extensive experimental research on pile constructed using this type of technique but in the specific context of cohesive soils. Short-term static load tests were carried out on a total of 9 test piles of various installation techniques in order to compare the respective performances. The promising features of the double rotary CFA have incited the LCPC & Durmeyer Company to implement an extensive experimental research on this type of pile technique but in the specific context of cohesive soils and more particularly in clayey marls. After load tests completion the research has been completed by an excavation of the double rotary CFA piles. All the collected data concerning the implemented program are reported.

Jan 1, 2002

By Venda Oliveira P. J., Correia A. A. S., Danisi C. M.

"AbstractA laboratory study has been undertaken to establish common understanding of the creep phenomenon of a Portuguese soft soil chemically stabilised with binders. In order to study the effect of different stress levels on the strength and on the creep behavior of the stabilised soil, oedometer creep tests and unconfined compressive tests were performed at different curing times. Results show that the creep stress level does not influence the unconfined compressive strength. In addition, the creep phenomenon increases the unconfined compressive strength of the treated soil. Two different secondary compression indexes were recognized from the one-dimensional compression curve which increase with an exponential trend with the creep stress level.IntroductionConstruction on soft soils requires a mandatory soil stabilization work to improve mechanical characteristics of the natural soil. Deep mixing method is a worldwide employed ground improvement method, nevertheless the creep phenomenon hasn’t been yet thoroughly analyzed. Most of the published papers have focused on the analysis of the compressibility and the strength of the soil-binder mixtures without considering the creep phenomenon. However, numerical results (Venda Oliveira et al. 2009) have shown that although settlements that occur during the creep stage (namely creep strains) are less in case of treated columns, they are still important especially due to the high loads applied to the stabilised soil. The few published studies about creep behavior of soil-binder mixtures reveal that the stabilization of an organic soil with cement induces a reduction of creep deformations, which is related to the amount of cement used and that the increase of the organic matter of the soil has a negative impact on soil stabilization, further inducing a slight increase in the creep deformations (Venda Oliveira et al. 2012).As part of the current research the effect of different stress levels on the creep behavior of a soft clayey-silt soil was studied. The binder mixture used to enhance the properties of the soil had a specific composition and quantity. Unconfined compressive strength tests (UCS) and UCS creep tests were carried out at pre-set curing times in order to analyze the creep behavior of the soil-binder mixture. In particular five different creep stress levels were studied to understand its influence on the strength and on the compressibility of the stabilised soil. In addition, considerations about the secondary consolidation index are also presented."

Jan 1, 2014

By Boleslaw A. Klosinski

Drilling of a pier hole is accompanied with stress releasing in the surrounding soil and often with loosening of soil at the pier base. In effect the drilled piers are more deformable than driven piles of comparable dimension. The bearing performance of a pier may be considerably improved by properly executed base grouting. Various techniques of base grouting are used; many of them were described by Bruce (1986). The grouting devices are often placed within the pier. Alternatively the soil at or under the base is treated by cement or chemical grout. Preloading of the base subsoil by use of a special grouting cell is considered as the most effective way. Treatment of the ground below pier base with cement or chemical grout may be also useful. It may be performed immediately after the pier construction or during service, as a measure for increasing the pier capacity.

Jan 1, 1995

By Klaus Pöllath

The Netherlands RandstadRail project makes use of a large range of sophisticated geotechnical techniques to allow a shield driven tunnel to approach the central station of Rotterdam. This paper describes the construction of three deep excavation pits constructed with 1.2 m and 1.5 m thick diaphragm walls. Besides the presentation of the actual diaphragm wall activities special consideration is given to the break-in and break-out situations of the TBM into the deep excavations pits using sealing blocks and partly glass fibre reinforcement in the diaphragm walls.

Jan 1, 2006

By Karl A. Higgins

In 1976, Prof. G. G. Meyerhof published a famous article in the Journal of Geotechnical Engineering titled ?Bearing Capacity and Settlement of Pile Foundations?. This article presents the authors opinions on calculating pile capacities in clays and sands, group capacities and pile settlement. A portion of the article presents correlations of shaft friction and end bearing to the Standard Penetration Test (SPT) N-value. Subsurface exploration via the Standard Penetration Test is the most widely used exploration tool in the United States, so correlations of pile capacity to N-value are significant to the practice of geotechnical engineering. Meyerhof?s SPT-N correlations are relatively simple calculations compared to other pile capacity computation methods presented in the article or found in other text books (such as the a-method, b-method, Nordlund, Vesic, Meyerhof?s semi-empirical, others) and therefore are popular amongst practicing geotechnical engineers. At the time these correlations were published by Prof. Meyerhof, utilization of dynamic testing with the Pile Driving Analyzer (PDA) was not widespread in geotechnical engineering practice. Prof. Meyerhof?s correlations appear to be based upon conventional static pile load testing of instrumented piles. Dynamic pile measurements to estimate a pile?s static capacity provides certain advantages over conventional static load testing, namely the determination of unit shaft friction values at discrete intervals along the pile, and the unit end bearing support value. The author has compiled a database of driven, displacement piles tested with dynamic methods (ref. ASTM D4945, Test Method for High-Strain Dynamic Testing of Piles). The data was collected between 2002-2010 and is comprised of displacement piles driven into coastal plain sediments in the mid-Atlantic states of Virginia, Maryland and the District of Columbia. In layered soils, dynamic testing in particularly helpful as it reveals the differences in unit shaft friction for varying soil types. One hundred ninety (190) piles are included in the database, with a corresponding 1,373 discrete shaft friction and 190 end (toe) bearing measurements. The pile type typically consisted of 12 and 14 inch square, prestressed, precast concrete piles; however, a significant number of piles were steel HP 12 or 14 inch sections. The database was sorted based upon soil type, and then correlations of shaft friction and end bearing were derived in the same or similar manner as Meyerhof?s original 1976 publication. The new correlations are compared to Meyerhof?s original values.

Jan 1, 2011

By Liu Run, Jia Zhao-lin, Yan Shu-wang

"Piles with diameter larger than 2m in engineering can be defined as large diameter pile, and piles used for oil platform foundation in Bohai Gulf, are usually over 100m long and 2m in diameter. Such long piles have to be manufactured by segments before installation, because of transformation and hoisting difficulties. The segments of the pile are assembled by welding during installation one to another. Normally, assembling two pile segments takes one day or even a longer time, which mainly depends on construction conditions. After pile segment assembling, it proves to be difficult to restart the successive penetration. The mechanism of pile refusal is discussed and the process of driving a segmented pile is simulated with a finite element program. The calculating results show that, when the stick-up stability was satisfied, increasing the length of the last segment of the pile and assembling the pile segments when the pile tip penetrates into a clay layer could greatly ease the difficulty of driving the pile. Furthermore, cutting down the pile extension time is also one of the most effective measures to minimize the refusal risk.1. InstructionIn recent years, more and more oil platforms with six or eight legs have been adopted in Bohai Gulf, China. The leg piles with diameters of 2m or more have to be driven to about 100m below the sea bed. Such long piles have to be manufactured by segments before installation, because of transportation and hoisting difficulties. The segments of the pile will be assembled during installation, in which a successive segment will be attached to a formerly penetrated one by welding (Fig.1). The assembling work often takes one day or even a longer time."

Jan 1, 2014

By Paul W. Mayne

Axial pile performance can be rationally evaluated within an elastic continuum framework using field results from seismic piezocone tests (SCPTu). Adopting a versatile Randolph-type elastic pile model, the approach can be applied to either traditional top down loading using an anchored reaction beam or the newer Osterberg cell that simultaneously pushes the base and shaft in opposite directions. The axial load distribution within the shaft is also evaluated. For site-specific data at a given site, the SCPTu is an optimal means for collection of subsurface information because it combines penetrometer readings and downhole geophysics in one sounding. The results obtained are at opposite ends of the stress-strain-strength curves, specifically the peak strength for capacity interpretations and the small-strain stiffness (Emax) for evaluating the initial deformations. Axial pile capacity can be analyzed using both direct and indirect CPT methods. As such, the approach allows for a complete representation of the axial load-displacement-capacity curve for pile response. Case studies are presented for deep foundations situated in stiff clays at two national geotechnical test sites located in Houston and College Station, Texas, using top down loading, as well as a third case study of a drilled shaft in clay till loaded by O-cell in Alberta.

Jan 1, 2009

By G. T. Hong

A numerical model for use in design is developed to predict the stresses and axial and bending displacements in a drilled pier in expansive soils. The prediction is based on the horizontal swelling pressures and uplift forces which act on the side of the drilled pier. The exponential suction envelope with the depth within the moisture active zone is estimated based upon the equilibrium suction, moisture diffusion coefficients obtained from laboratory tests, and minimum suction at the ground surface of the site based on field conditions. The volume change of soil is based on suction variations, soil properties, overburden pressures, crack influences, and the relationship between moisture contents and suctions. Considering the movement active and anchor zones on a soil-pile system in expansive soils, horizontal swelling pressures are formulated using the shear strength of an unsaturated soil and the Mohr?s circle and failure envelope. The movement active zone has two sub-zones in which horizontal swelling pressures are attributed to passive earth pressure failure and suction change in the upper and lower sub-zones, respectively. Horizontal swelling pressures which occur in the anchor zone are assumed to be in the at rest condition. The shear stress generated on the vertical surface of a drilled pier is supported by the nonlinear curves of load transfer versus relative displacement. The axial behavior and lateral bending of the pier in expansive soils are simulated using a beam column approach. The computed axial and bending displacements and stresses are used to provide structural design of the pier. Figures of computed results for typical cases are presented.

Jan 1, 2007

By R. D. Short

Environmental regulations for noise and air pollution are directly affecting the type of equipment and construction techniques being utilized for pile driving construction using diesel hammers in California and elsewhere. Consequently, the cost of construction is increasing and in some cases, the use of diesel pile hammers has been prohibited. Based on the trend in California and elsewhere in the world, environmental constraints are spreading and becoming more restrictive. The City of Tokyo, Japan, for example has banned the use of diesel hammers. Environmental restrictions on diesel hammers can be satisfied by using modern hammers, clean burning fuels, synthetic lubricants and pre-excavation techniques.

Jan 1, 1989

By Shahriar Vandani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles (2.6 km) of highway, including seven new bridges, three new cut-and-cover tunnels, and a new undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles (9 km) from the San Andreas Fault, capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. The Main Post Tunnels (MPT) are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) long. The MPT site underlain by loose sandy soils susceptible to liquefaction and lateral spreading. Excessive racking and permanent displacement due to lateral spreading are identified as the main seismic vulnerabilities. Analyses showed that without ground improvement, tunnel racking of over 5 inches (13 cm) and permanent lateral tunnel displacement of up to 15 feet (4.6 m) could be anticipated. Cement Deep Soil Mixing (CDSM) is proposed to mitigate slope displacements and increase lateral stiffness of the foundation materials to reduce tunnel racking. A series of 2-D fully dynamic time domain analyses were performed to evaluate the performance of CDSM, confirm that performance criteria are met, and optimize the CDSM geometry and replacement ratio. The use of CDSM reduced the permanent tunnel displacement from over 15 feet (4.6 m) to less than 1 inch (2.5 cm). Tunnel racking was also reduced significantly. The adopted analytical approach presented herein can be considered for future tunnel design projects in seismically active areas.Introduction The Main Post Tunnels (MPT) are an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. The MPT are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) in length. As shown on Figure 1, the project site is located in a seismically active area, about 5.6 miles (9 km) east of the San Andreas Fault and 12.5 miles (20 km) west of the Hayward Fault. The San Andreas Fault can generate magnitude 8 earthquakes while the Hayward Fault is capable of producing magnitude 7.3 earthquakes. The design Peak Bedrock Acceleration (PBA) is 0.46g for the upper level design earthquake. The project alignment is shown on Figure 2."

Jan 1, 2014

By Ali Porbaha

The use of soil nailing technology as a cost effective alternative for excavation support and slope stabilization has substantially increased in the United States during the last decade. For example, in the past thirteen years, more than 185,800 square meters of soil nail walls have been constructed in California alone. The conventional soil nail systems pose difficulties when ground conditions are subject to caving, for instance for silty sand (sugar sand) or cobbles and boulders. The construction industry has developed self drilling hollow bar systems (or pressure injected bored, IBO) that combine both drilling, placing and grouting in a single operation as a solution to speed up construction. While the system is extensively used for temporary applications, nevertheless, some concerns, particularly about corrosion, has limited the use of this technology as a permanent system in North America. This study presents several issues related to self drilling soil nail systems, the results of a field investigation and a summary of the research project.

Jan 1, 2006

By John A. Dal Pino

This paper describes two independent building underpinning projects during the construction of the Los Angeles Metro Rail System. The first project involves pinpile underpinning of a building along the Red Line which is the main heavy-rail portion of the system. Vertical and inclined friction pinpiles were constructed, using drilling equipment in a low-overhead height space, to support underpinning grade beams. This underpinning permitted the demolition of the building caissons so that the subway tunnels could pass beneath the building unimpeded. One of the piles was statically tested in compression. The second project involves the use of traditional pit piers for the underpinning of historic buildings along the Pasadena Blue Line, which is one of the light-rail branches from the Red Line. The piers were designed for various loading conditions and to minimize differential settlement of adjacent foundations. The piers will be internally braced with steel struts to be designed by the contractor.

Jan 1, 1996

Jan 1, 2000

By Mario Aiezza

This paper outlines the results of a relationship developed during the design and construction of the foundations for the Gallery Towers project in Melbourne. Both the builder and the piling contractor were determined to arrive at a satisfactory foundation solution to the problems encountered at the site. The scope of piling work was to provide load-bearing piles under the building columns, some of which were located within a retention system that also required a piling solution. Geological conditions were variable and challenging. The site area was small and located adjacent to the National Arts Centre in the developed Southbank area, a high density office area. This presented logistical problems in limiting construction traffic on site and also demanding minimal noise and vibration emanating from piling activities. The piling contractor, Vibro-Pile, and the builder, Walter Construction Group, faced the challenges presented with a refreshing cooperative attitude that was beneficial to both companies. Commercial issues rising from design and construction problems were first put apart in order to allow the respective technical department of each company to work with minimum constraints to achieve the most cost effective solution. In the process usual adversarial attitudes resulting in loss of time and money was avoided. A number of issues were addressed successfully at minimum cost and time during this contract. Despite the difficulties encountered, the job was completed on time and with negligible claims for extras, resulting in the development of a strong mutual respect between both companies.

Jan 1, 2002

By George J. Tamara

The urban environment presents special challenges for the design and construction of earth retention systems. Complications arising from difficult subsurface conditions are compounded by the presence of urban infrastructure and existing and prior construction. The proximity of adjacent structures as well as intense prior use can cause special concerns including the potential for archeological artifacts or contaminated ground or ground water. Utilities and structures may be particularly vulnerable to the effects of ground movement, dewatering and vibrations. Difficulty of access, congestion and limited work areas may severely restrict means and methods of construction. Dewatering may be limited or prohibited because of concerns for disposal of clean or contaminated water, depletion of aquifers, drawing of contaminants to the site or dewatering induced settlements.

Jan 1, 2003

By Kodi Ranga Swamy, N. Sankar, M. Akhila

"Until recently, liquefaction-related studies concentrated on clean sands believing that only sands are susceptible to liquefaction. However, a few earthquakes like 1976 Tangshan earthquake, the 1989 Loma Prieta earthquake, the 1999 Kocaeli earthquake, the 2010 Chile earthquake, and the 2011 Christchurch earthquake, etc. showed that sand with fines could also liquefy. The research findings on liquefaction of silty soils are limited, and several structures constructed on such soil deposits are damaged during the past earthquakes. Some previous results of research on earthquake events show an increase of liquefaction resistance in silt soils with increase the fines content, but some report the opposite trend. This study presents the results based on undrained triaxial cyclic tests which were carried out on the fine sand with fines (0%, 10%, 20% and 40% fines). The samples were prepared at the required unit weight (Dr = 50%) and saturated by using back pressure and cell pressure increments. Each consolidated sample is subjected to cyclic loading with sinusoidal wave load form at a frequency of 1 Hz. The liquefaction resistance is evaluated in terms of cyclic stress ratio required to cause 100% pore pressure or 20% failure strain occur at 15 numbers of load cycles. Results are presented in forms of pore pressure build up and axial strain propagation plots. As the fines content increased, an increase in liquefaction potential was observed.INTRODUCTIONLiquefaction and related phenomenon have been responsible for tremendous amounts of damage all around the world. In general, the liquefaction may occur in fully saturated sands, silts and low plastic clays. When the saturated soil mass is subjected to seismic or dynamic loads, there is a sudden buildup of pore water within a short duration, and it could not dissipate which leads to reducing the effective shear strength of soil mass. In this state, the soil mass behaves like a liquid and causes large deformations, settlements, flow failures, etc. This phenomenon is called soil liquefaction. As a result, the ability of soil deposit to support the foundations of buildings, bridges, dams, etc. is reduced. Liquefiable soil also exerts a higher pressure on retaining walls.This lateral movement of soil could cause settlement of the retained soil. A sudden build-up of pore water pressure during quake also triggers landslides. Liquefaction damages of structures are commonly observed in low-lying areas near the rivers, lakes, and oceans."

Jan 1, 2017

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity. Now this important project is in progress and this report describes the special foundation techniques used on the great ship lock Hohenwarthe. Hohenwarthe is a double- bay ship lock of considerable scale, which is notable for recirculating water rather than letting it flow. It includes 44 800 m2 ( 481 720 sq. ft) of up to 55 m ( 180 ft) deep cut- off walls, ground water control, 1248 bored piles with a depth of 22 m ( 72 ft ) serving as foundation and 28 000 m ( 91 864 ft) of soil densification with vibroflotation equipment for ground improvement. In the year 2003 the project shall be completed and all ships can travel from the West to the East through Germany without expensive and time- consuming detours through other canals and locks.

Jan 1, 2000

By Harry K. Weatherbee

The paper presents a design case study for a four-story correction facility addition in south Boston, Massachusetts, supported on friction piles driven into the Boston Blue Clay. 356 mm (14-in.) square prestressed-precast (PSPC) concrete piles were selected as they were found more effective and economical. A static load test was performed where the pile was brought to "failure". The load test data were evaluated to estimate the Ultimate Pile Capacity as well as the Ultimate Unit Skin Friction (Adhesion) to serve as a design tool for friction pile projects in the south Boston Area.

Jan 1, 2003