Search Documents

By Kretschmar. U. H.

Fieldwork in the Meguma of Nova Scotia and Archean equivalents shows that bedding-parallel quartz lode gold veins (LVs) commonly occur at the top of graded elastic sequences. We define a "gold cycle" (GC) by analogy with Bouma turbidites and show that most "shear zones" and "lamprophyres" correspond to the upper pelagic-pelitic (E) division. We describe GCs from Archean Chester Twp, ON; Elmhirst, ON; Bourlamaque, QC; "intrusions" and interpret them as crystal tuffs and tuff-breccias. Extensive early Archean pyroclastic volcanism is implied: the genesis of trondjhemite-tonalite-granodiorite (TTG) rocks must be re-examined. The geopetal nature and asymmetric alteration of LVs indicates genesis from sea-floor hydrothermal vents. Textures suggest that often quartz was deposited as a gel. Vent geometry (fracture, point source or diffuse seep), bottom topography and vent spacing is reflected in wade-thickness plots. GC facing directions survive metamorphism. The Bourlamaque batholith was a flat-lying sheet of quartz-feldspar-hornblende crystal tuff, and isoclinal folding has repeated one or more gold-bearing horizons. Syngenesis clarifies and simplifies LV formation with major implications for models. Exploration becomes more cost-effective. Basin analysis, whole rock geochemistry, ore lens geometry and vent spacing can be used.

Jan 1, 2011

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By J. C. Beidelman

One of the oldest settled portions of Canada is that "strip of land" extending into the Gulf of St. Lawrence, known as the Gaspe peninsula, with the Bay of Chaleur on its southern boundary. This "strip of land" is still so very sparcely populated that only at a few places does settlement extend more than a few miles from the coast. ? The peninsula is 160 miles long, 75 miles wide and with the exception of the above mentioned settlements is a mountainous wildness-void of all roads or inhabitants. Developments in the interior, of all nature, out-side of the cutting of timber by limit holders, was entirely lacking until the year 1915, when mining was first commenced. In the summer of 1844 Sir William Logan made a preliminary survey across the peninsula, from Cape Chat on the Gulf of St. Lawrence to Cascapedia on the Bay of Chaleur, passing through a country ?of which very little was known at that time. After a rather rough trip to the headwaters of the Grand Cascapedia river, Logan's party descended this river to its mouth, passing ten miles west of what is now known as the Federal mines. There is no record of Logan, or of any of his party, finding zinc or lead ores of any character on their journey across the peninsula, and until 1909 no precious or base metals were discovered within reasonable distance of Logan's survey.

Jan 1, 1924

By E. Engelbrecht

"A pressure non-oxidative leach is employed at Anglo American Platinum Base Metal Refiners to extract nickel from a slow cooled matte. The design base requires two 80 m3 autoclaves in parallel to achieve a nickel extraction of 60% at the nameplate capacity of 32.4 ktpa nickel plated. Isothermal modelling of mineralogical and chemical concentration profiles, through a reactive mass balance, permitted rate constant parameter estimation and selection of the most probable reaction pathway. The model was validated with plant data up to a capacity of 26 ktpa Ni plated and suggested by extrapolation that nameplate capacity may be viable through one 80 m3 autoclave.INTRODUCTION Anglo American Platinum Base Metal Refiners is situated on the outskirts of Rustenburg in the North-West province of South-Africa. The refinery produces nickel cathode, copper cathode, cobalt sulphate powder, covellite rich copper pressure leach residue and bulk sodium sulphate through an integrated circuit that refines slow cooled converter matte. The converter matte is milled, non-magnetics are separated as solid nickel copper matte (NCM), and the magnetics are leached yielding a pressure vessel liquor (PVL). The remaining solid platinum group metals (PGM) concentrate after leaching is sent for downstream processing in the Precious Metals Refinery (Hofirek & Kerfoot, 1992). The work presented here is applicable to the base metals refinery which receives the two base metals feed stocks NCM and PVL. In 2009 the capacity of the refinery was upgraded from 21 ktpa nickel cathode plated to 32.4 ktpa. This paper deals with evaluating the capacity of the pressurised non-oxidative nickel leach (NOX) process which accounts for at least 28% of the nickel leached from NCM by design. The NOX design base requires two 80 m3 autoclaves divided into four compartments operated in parallel at 155°C and 600kPa(g). Elevated temperature is required to speed up the leach kinetics of particularly nickel and iron which are trapped in slow leaching mineralogical phases namely millerite and bornite, (Dinham, 2006). The stated equivalent capacity for the NOX configuration was 32.9 ktpa nickel plated at first pass nickel and iron leach efficiencies of 60% and above 80% respectively and is a key step for the selective removal of iron (Bryson, Hofirek, Collins, Stiksma, & Bereaowsky, 2008)."

Jan 1, 2017

"2.1. General Considerations and Properties2.1.1. IntroductionOur present knowledge of the platinum-group elements (POE) is extensive, the reason being two-fold. The elements have many uses and, moreover, they exhibit extremely varied chemical behaviour, depending on their state of oxidation and chemical environment. The present chapter reviews a selected body of material which is of particular relevance to mineralogy and geochemistry.Comprehensive treatises on the POE include those by Mellor (1956-1957), Gmelin (1938-1957) and Pascal (1958). The inorganic chemistry, particularly coordination chemistry, has been dealt with in works by Griffith (1967), Hartley (1973) and Livingstone (1975), and the analytical chemistry by Walsh and Hausman (1963), Beamish (1966) and Beamish and Van Loon (1972, 1977). Darling (1973) and Savitsky (1978) have reviewed the metallurgical properties and applications of the metals. Goldberg and Helper (1968) have reviewed the thermochemistry and oxidation potentials of POE systems, and Wagman et at. (1969) have also provided selected values of their thermodynamic properties. The geochemistry of the POE has been reviewed by Yushko-Zakharova et at. (1967), Cousins (1973), Cabri (1974), and Naldrett and Duke (1980).Platinum was used briefly as a coinage metal in ImperialRussia. Otherwise, the principal early use for platinum and its alloys was in the fabrication of chemically resistant apparatus. Subsequently, a large part of platinum production was utilized for catalysts in the sulphuric acid and ammonia industries. Platinum has been replaced by vanadium pentoxide in the manufacture of sulphuric acid, but, in recent times, catalytic upgrading of petroleum and emission control systems for automobiles have opened further huge markets for the metal. All of the POE find uses either as reagents or catalysts in the synthesis of organic compounds, e.g., in the Wacker process, which uses palladium chloride to catalyze the production of acetaldehyde from ethylene. There are, of course, a large number of specialized uses for the elements, particularly in alloys, temperature measurement devices, cancer therapy and so on."

Jan 1, 1979

By Lawrence D. Meinert

Abstract-Most large skarn deposits are zoned in both space and time relative to associated intrusions. Zonation occurs on scales from kilometers to micrometers, and reflects infiltrative fluid flow, wallrock reaction, temperature variations, and fluid mixing. The most spectacular examples of skarn zonation usually occur at the skarn-marble contact, where transitions between monomineralic bands can be knife sharp. Other small-scale examples occur in zoned veins and individual mineral crystals. Although, visually striking and scientifically interesting, in mineral exploration these small-scale variations are less useful than deposit- or district-scale zonation. In most skarn systems there is a general zonation pattern of proximal garnet, distal pyroxene, and vesuvianite (or a pyroxenoid such as wollastonite, bustamite, or rhodonite) at the marble front. As well, individual skarn minerals may display systematic color or compositional variations within the larger zonation pattern. Such patterns are reviewed for 14 well-studied examples of Cu, W, Sn, Au, and Zn-Pb skarns. In addition, many deposits have endoskarn or other alteration of the associated intrusion, and recrystallization or other subtle changes have occurred in the surrounding wallrocks. Copper skarns, such as Mines Gaspé in Quebec and Big Gossan in Irian Jaya, have high ratios of garnet:pyroxene and are zoned outward from the intrusion, to garnet, to pyroxene, to massive-sulfide replacement and vein deposits. Garnets in Cu skarn are Fe-rich and change from dark red-brown near the intrusive contact to paler brown, green, or yellow in distal locations. Pyroxenes in Cu skarns are pale and diopsidic near the intrusion, and become darker and more Fe- and Mn-rich away from the intrusion. Tungsten skarns, such as Salau and Costabonne in France and Pine Creek and Garnet Dike in California, have intermediate ratios of garnet:pyroxene, are more extensive vertically and along strike than perpendicular to the intrusive contact, and have zonation patterns commonly complicated by overprinting of metamorphic lithologies. In W skarns, garnet is commonly subcalcic and the pyroxene is Fe-rich, reflecting particularly reducing wallrocks or great depth of formation. Tin skarns, such as Dachang in China and Moina in Australia, also can have subcalcic garnet and Fe-rich pyroxene, but this reduced mineral assemblage typically is due to an association with reduced S-type granites. Tin skarns differ from most other skarn types in having a late greisen stage that may replace earlier Sn-bearing calc-silicate minerals, thus liberating Sn to form cassiterite. Many high-grade Au skarns, such as Hedley in British Columbia and Fortitude in Nevada, have low ratios of garnet:pyroxene and are associated both with reduced plutons and reduced wallrocks. Goldrich zones occur in Fe-rich, pyroxene-dominant, distal skarn. Zn-Pb skarns, such as the Yeonhwa- Ulchin district in Korea and Groundhog in New Mexico, have low ratios of garnet:pyroxene and generally form distal to associated intrusions. These skarns also are zoned from proximal garnet to distal pyroxene and pyroxenoid (bustamite-rhodonite), with significant zones of massive sulfides within and beyond skarn. Manganese enrichment of most mineral phases, particularly pyroxene, is characteristic of distal zones. Fundamental controls on skarn zonation include temperature, depth of formation, composition and oxidation state of associated plutons and wallrocks, and tectonic setting. Most W skarns form at relatively great depth, 5 km to 20 km, with extensive high-temperature metamorphic and metasomatic mineral assemblages. In contrast, most other skarn types are relatively shallow, <10 km and mostly <5 km, with limited, lower temperature metamorphic aureoles. Differences in oxidation state correlate well with different skarn zonation patterns, particularly garnet:pyroxene ratios and compositions, and can be used in both classification of and exploration for s

Jan 1, 1997

By B. Konda, R. Lauer, D. Camilucci, D. Gladwin

"Income based taxes are significant cost elements to be considered in evaluating investment in new mine development. This paper presents the results of comparative analysis of effective income-based tax rates for mining in the Northwest Territories (NWT), selected Canadian provinces and international jurisdictions. The study was done as background to a review of royalty regulations for the NWT. ObjectiveThis paper presents results of comparative analysis of effective mining royalty1 rates, and combined effective mining royalty and income tax rates on selected mine models for the Northwest Territories (NWT), with those for several other jurisdictions in Canada and abroad which compete with the NWT for mining investment.BackgroundThe February 27, 1995 federal budget directed the Department of Indian Affairs and Northern Development (DIAND) to proceed with a comprehensive review and amendments to northern natural resource management legislation in order “to increase revenues and ensure a fair return to the Crown.” DIAND is responsible for the administration of the Territorial Lands Act, and its regulations.The Territorial Lands Act gives the Governor-in-Council the authority to “… make regulations for the leasing of mining rights in, under or on territorial lands and the payment of royalties therefor,…”. In the NWT, the Canada Mining Regulations (CMR) provide for the disposition of mineral rights for most minerals, other than coal, petroleum and related hydrocarbons, in return for the payment of a royalty to the Crown.As part of this review of the NWT mining royalty regime, several computer mine models were developed and tax regimes in a number of jurisdictions were analyzed. Effective mining royalty rates, and the combined effective mining royalty and income tax rates were compared across the jurisdictions. The results presented in this paper are a part of the background work done in preparing a discussion paper on proposed changes to the NWT mining royalty that is expected to be released for public consultation in the very near future."

Jan 1, 1997

By C. Doyle, D. M. Hoffman, C. Díaz, J. Hrepic, W. J. Koshut, R. H. Hanewald

"Recently, lining life of the INMETCO submerged arc furnace has been dramatically extended from an average of eleven months in the 1980s to a current record of 34 months. This paper summarizes test work and operating results describing the development and establishment of slag parameters that reduce corrosion of the magnesite-chrome refractory lining.The desired slag parameters are now maintained by utilizing waste streams as slag additives. This paper also discusses the successful evaluation of a rebonded-fused-grain magnesite- chrome refractory as a lower cost, more thermo-mechanically forgiving alternative to a fused-cast magnesite-chrome refractory that had been the refractory of choice in previous years at INMETCO.IntroductionSince 1978, INMETCO, a wholly owned subsidiary of INCO Limited, has been well known for recycling by-products from the production of stainless steel, namely, EAF bag- house dust, mill scale and grinding swarf. INMETCO operates the only smelter in North America dedicated to the recovery of nickel, chromium, and iron from hazardous and nonhazardous waste. The process was developed in the research laboratories of INCO. In recent years, the process has been successfully modified to accept a wider variety of other specialty steel waste streams including: spent pickling solutions, pickling and waste water treatment filter cakes, acid scale, carbon brick, spent bag-house bags, torch cutter dust, spent dolomitic and chromium-bearing refractories, and rechargeable nickel-cadmium batteries."

Jan 1, 1997

By Xiqing Wu, Liang Dai, Tao Yue, Longsheng Yi, Ruifang Wang

Magnetic seeding flotation (MSF), i.e. adding magnetic seeds and pre-magnetization-flotation, is a new flotation technology especially for fine particles, which improves the flotation performance by enlarging the apparent size of the particles in a way of magnetic agglomeration. Both the fine coal slimes with a size of 66.68% –38µm and the pyrite slimes with a size of 73.95% –23 µm were investigated by the MSF, respectively. Flotation tests with variable of dosages of magnetic seeds and polyacrylamide were conducted, and some measurements, such as laser diffraction size analysis, magnetic susceptibility by vibrating sample magnetometer (VSM) and infrared spectroscopy (IRS), were also applied in order to probe the mechanism of the MSF. Based on the tests, measurements and calculations it was found that both the recovery of coal and the flotation kinetics of pyrite slimes increased with the additions of the magnetic seeds, and in the presence of polyacrylamide the coal flotation was further strengthened due to a synergetic effect of magnetic seeds and polyacrylamide on the flotation and a relatively larger apparent size of slimes after additions of magnetic seeds and polyacrylamide. The reason for the MSF lies in fact that the presence of the polyacrylamide intensified the adsorption of magnetic seeds on the coal particles and increased the coverage of the magnetic seeds on the coal surface from 0.2 to 1.3 wt%, resulting in increased magnetic susceptibility of coal particles from 9.13×10-9 to 22.17×10-9 m3/kg and thus a low magnetic field strength of pre-magnetization needed for the magnetic agglomeration among the coal particles from 602 to 24 mT prior to proper flotation. IRS shows that polyacrylamide chemisorbed on the surfaces of both coal particles and magnetic seeds, thus acting as the bridging media between particles and seeds.

Jan 1, 2016

By Paul W. Billwiller

Introduction In 1937, the Britannia Mining and Smelting Company, Limited, was carrying on an extensive exploratory diamond-drilling programme. Most of this drilling was done on the 4100 level, the lowest working level in the mine. One of the exploratory diamond-drill holes, at approximately 12,500 feet from the portal of the tunnel, encountered heavily mineralized stringers of chalcopyrite and sphalerite in silicified grey schist. The mineralization was encountered just to the hanging-wall of the green mottled schist at a point 350 feet south of the 4100 tunnel. To delimit this new orebody, drifts and cross-cuts were driven on 3500, 3800, and 4100 levels to the hanging-wall in the area of the projected mineralization. On the 3500 level, the top of the mineralized zone was encountered. The zone was thoroughly explored by drifting and diamond drilling. The mineralization, however, was not sufficiently concentrated to be of commercial grade. On the 3800 level, the zone was found to consist of disconnected stringers of chalcopyrite and pyrite. Drifting was continued to the west and a long lens-shaped area of grey schist containing fairly heavy stringers of chalcopyrite was delimited. This lens later proved to be very close to the top of the commercial mineralization of the No. 8 orebody. On the 4100 level, a diagonal cross-cut was driven to the footwall of the downward projection of the mineralized zone. Diamond-drill holes from this cross-cut indicated a zone of heavy mineralization. A drift was driven off the cross-cut parallel to the zone and some distance to the footwall of it. Further diamond drilling disclosed a mineralized zone approximately 300 feet long and 35 feet wide containing sphalerite, chalcopyrite, and pyrite. The foregoing development work indicated a fairly large lens of mineralization of sufficient concentration to be classed as ore between the 4100 and 3800 levels. To explore this mineralization at depth, long diamond drill holes, dipping at minus 57° and minus 80°, were planned from some point to the hanging-wall of the orebody. The 4100 level was not suitable for small development headings, due to wider gauge track and larger cars than on the levels above. Therefore, a raise was driven from the diagonal cross-cut on the 4100 level to a point some 70 feet above and just inside the footwall of the orebody. From the top of the raise, drifts were expanded east and west to delimit the ore zone. In addition, a long cross-cut was driven 350 feet to the hanging-wall, and drifts were opened east and west from the end of the cross-cut to provide diamond-drill stations for the exploration of the orebody at depth.

Jan 1, 1946

By Brian E. Robertson

"This paper summarizes work carried out at the Dome Mine to mechanize the mining of narrow veins of less than 1.5 m in width by the introduction of new mining methods and specifically designed electric LHDs.Extensive mining trials have been conducted using sublevel blasthole, modified Avoca, and resuing mining methods. The introduction of the Microscoop and the Jarvis Clark remote, radio-controlled scooptram has increased mucking productivity.As a result of this work, additional narrow vein stopes are now being prepared for production. In the future, narrow vein stoping wil lprovide a greater percentage of the total mill tonnage.IntroductionThe Dome Mine, which is owned and operated by Dome Mines Limited, is located at Timmins, Ontario. Production has been continuous since 1910 and in 1984 was increased from 1814 to 2721 tonnes per day.At least six distinct ore types have been recognized at the mine. In general, these orebodies can be broadly categorized into wide and narrow deposits. The wide deposits are approximately lenticular in shape and vary in width from 10 m to 40 m. The narrow orebodies consist of quartz and quartzankerite veins ranging in width from a few centimetres to six metres. The average dip of the veins is 65 degrees.Since the I970s, mining activity has been largely concentrated in the wider orebodies using highly productive open sublevel blasthole and mechanized cut-and-fill stoping methods. With the demise of shrinkage stoping in 1975, investigations were initiated to develop new mining methods and introduce LHDs - truly designed for narrow orebodies. These investigations resulted in test trials of the sublevel blasthole, modified Avoca, and resuing mining methods. Consultations with equipment manufacturers and suppliers led to the development of the Jarvis Clark remote, radio-controlled electric scooptram and the introduction of the France Loader Microscoop."

Jan 1, 1986

By D. L. Cluff

Ventilation Air Methane (VAM) is a high volume low concentration methane source. The capture or use of methane from VAM is challenging, which results in the routine discharge of methane into the atmosphere. Mitigating VAM has the benefits of providing an energy source and reducing the atmospheric Greenhouse Gas (GHG) burden. The GHG radiative forcing effect of methane is 17?23 times as potent as carbon dioxide on a 100-year time horizon. Thus, any reduction in atmospheric methane would be beneficial. The calorific value of methane is 55.5 MJ/Kg; therefore, a 100 m3/s flow with VAM concentrations from 0.1?1% can provide 3.8?38 MW of exploitable power. Strategies to mitigate VAM such as: Thermal Flow Reverse Reactors (TFRR), Catalytic Flow Reverse Reactors (CFRR), Lean Burn and Catalytic Gas Turbines, Biothermica Vamox®, Megtec VOCSIDIZER©, and Vamcat? are briefly reviewed. The review of VAM mitigation technologies reveals disadvantages such as the need to maintain a minimum internal heat capable of oxidizing the methane. This requirement uses all of the available methane up to the point of reaction sustainability and up to half at the highest methane concentration in VAM. Some systems may introduce a pressure drop to the ventilation system, which would impinge on the existing ventilation system design. These impediments necessitate the development of a more amenable technology. In the proposed system, gas turbines (GT), coupled to a combustion chamber with an external fuel supply, assist the combustion of the VAM. The combustion-chamber coupled system provides electricity, while the heat contained in the GT exhaust gases increases the temperature of the VAM, encouraging the development of a flame inside a combustion chamber. The flow from the combustion chamber streams through a primary air/fluid heat exchanger capable of producing steam of a high enough quality to generate electricity using conventional steam turbines. The residual heat after primary extraction, directed through other equipment, provides additional heat based products such as industrial scale dry air, chilling by an absorption chiller or hot water. The overall design of the system is scalable for low to high VAM flows or variations in concentrations and is capable of providing the company or community with heating, chilling, hot water, electricity or motive force as needed by the particular site or community. The Multi-generation system uses heat from three sources to provide clean efficient energy while mitigating the atmospheric emissions of methane. These sources are heat from the GT, often considered waste heat, heat from fuel injected into the igniters and heat from the VAM. The opportunity to collect carbon credits may improve the economics. In order to design a system with this capacity, a detailed analysis of the combustion characteristics of three separate flows is required. VAM is the main airflow, having the highest volumetric effect, while the GT exhaust and the additional fuel added to the hot exhaust flow of the gas turbine are lower flows, but have a higher velocity and temperature. The aim of the modeling undertaken in this work is to establish the combustion dynamics, degree of pre-heating required and the geometry essential to the design of combustion based VAM mitigation multi-generation systems.

Aug 1, 2013

By F. Baczek, S. S. Rocks, D. Chaiko, C. Eyzaguirre, S. Asihene, T. Walters

The majority of efforts to improve primary copper sulfide leaching have focused on solution chemistry, temperature, O2 pressure, ultra-fine grinding, the use of catalysts, etc. Historically, very few studies have focused on the solid/solution interface. A new, patent pending approach to catalyzed, copper sulfide leaching has been discovered by FLSmidth that enables manipulation of the 2-D semi-conductor properties of chalcopyrite surfaces to the benefit of higher electrochemical reactivity. Copper dissolution rates are then further accelerated by incorporating a Stirred Media Reactor (SMRt) into the process. By using minute amounts of Cu2+ to "pre-activate" chalcopyrite, leach times have been reduced from >20 hours with incomplete Cu dissolution to <2 hours with 98+% Cu dissolution at 80°C. The pre-activation process takes only minutes to complete at temperatures of 80°C or less. The total atmospheric leaching process, incorporating the pre-activation and Stirred Media Reactor is compatible with existing SX/EW processes. Results of batch leach testing are presented and possible mechanisms are discussed.

Jan 1, 2015

An essential tool for every step ? Early field survey ? Handheld satellite phones ? Portable satellite phones ? Exploration and Drilling ? Handheld satellite phones ? Portable satellite phones ? Production ? Handheld and portable ? Fixed Satellites systems ? Asset tracking systems Main applications via satellite ? Voice and Fax communication ? Internet access and E-mail ? Video conferencing ? Interconnection to mobile phones, 2 way radios, long range WIFI ? Equipment Tele-maintenance ? Telemedicine ? Crew and morale calling ? Vehicle and asset tracking

May 1, 2006

By J. Asfahani

"The inverse slope method (ISM) was applied to reinterpret vertical electrical soundings (VES) data from pits at the Al-Sharquieh phosphate mine, in order to demonstrate applicability and suitability of the ISM for interpreting VES data from sedimentary phosphatic environments. The ISM overcomes limitations of the curve matching method and the complexity of lithological sections. The ISM geo-electrical interpretation results correlated well with lithologies of the pits. This method characterized resistivity and thickness of the phosphatic layer, and identified favourable phosphate-prospecting areas using the newly developed thickness/depth parameter. The ISM is recommended for interpreting VES measurements in similar sedimentary phosphatic regions.RÉSUMÉ La méthode d’inversion de la pente (ISM) a été utilisée pour réinterpréter les données de sondages électriques verticaux (VES) effectués dans des puits de la mine de phosphate Al-Sharquieh, afin de démontrer l’applicabilité et la pertinence de cette méthode pour interpréter les données VES dans des environnements de sédimentation de phosphates. Cette méthode (ISM) surmonte les limitations de la méthode de comparaison de courbes et la complexité des sections lithologiques. Les résultats de l’interprétation géoélectrique ISM correspondaient bien aux lithologies des puits. Elle a permis de caractériser la résistivité et l’épaisseur de la couche phosphatique et d’identifier les secteurs favorables à la prospection pour le phosphate en utilisant le paramètre nouvellement développé épaisseur/profondeur. ISM est recommandée pour l’interprétation des mesures VES dans des régions semblables où se trouve du phosphate sédimentaire."

Jan 1, 2016

By Richard Howie

Avian Diversity ?? Pre-mining ?? 110 - 125 species would have occurred ?? Dominated by forest species ?? Wetland productivity unknown ?? Post mining ?? 192 documented ?? Forested species in reduced numbers ?? Increase in wetland species ?? Increase in open country/grassland species

May 1, 2008

By George C. Bateman

WHAT I would like to do is to talk for a while tonight about the Canadian mining industry in wartime-at least, the Canadian mining industry as viewed through the eyes of the Metals Controller. There is nothing quite like the Canadian system in the system of controls in the United States, because the Canadian Controller combines the functions of a good many of the organizations here. I think the nearest counterpart would be the Divisional Chiefs of the WPB-although they have perhaps less authority and operate in a somewhat narrower field. My own field, as you know, is the metals and minerals-all of them, as a matter of fact, with the exception of steel and iron and coal and oil. And as I am responsible for supplies not only from domestic sources but also from foreign sources, I exercise most of the functions of the WPB and some of the functions of the Board of Economic Warfare. As my department is also responsible for stock-piling and for the financing of new operations, I therefore exercise some of the functions of the Metals Reserve and also of the Defense Plants Corporation. Being an administrator under the Wartime Prices and Trade Board, I also have the same function in relation w the price of metals as the OP A. The Canadian system of controls is compact, relatively simple, and I believe reasonably efficient. I think two of the reasons for that are that both the Controllers and the Directors of production are clothed with very wide authority, and also the fact that all the buying for the three arms of the service is done through the Department of Munitions and Supply, of which we are a part.

Jan 1, 1943

By John Dasher

The analyses reported on in this paper indicate that there are hydrometallurgical routes from sulphide concentrates to copper that are potentially competitive with smelters which are not permitted to emit sulphur oxides. The various hydrometallurgical processes, and their economics, are discussed.

Jan 1, 1973

By Stephan I. Zajac, Roger A. Blais, John B. Stubbins

THE iron deposits of central Labrador occur within a relatively small area, herein called the Knob Lake Iron Range, in which a northwest-trending series of low hills and ridges defines the height-of-land at the boundary between provinces of Quebec and Newfound-land. Approximately two-thirds of the deposits are in Quebec and the remainder in Labrador, with several deposits straddling the inter-provincial boundary. These deposits are being exploited in open-pit mines by the Iron Ore Company of Canada centered at Schefferville, Quebec. Since 1954 this company has produced more than 56 million tons of iron ore to become Canada's leading iron ore producer. With indicated reserves of more than 375 million tons of direct-shipping ore and large tonnages of iron formation amenable to beneficiation, this mining district is assured of a long life. This paper describes the Knob Lake iron ores and their geological settings and stresses the features that lead to a better understanding of their origin. The

Jan 1, 1961

By J. A. Russell

AS THE LOCAL electric generating plants increased in size and capacity and costs of producing electricity came down, it became apparent that it was no longer good economy to operate individual boiler plants at the Company&apos;s various collieries to power steam hoists and compressors. Great economies could be made by burning the Coal at central power plants and using electric power at the collieries. During the period after the end of the war, a steady and continuing programme of replacing first the smaller steam-driven units, and later the steam-driven compressors, was undertaken, and finally the larger hoists, those at No. 12 Colliery in New Waterford and No. 20 Colliery in Glace Bay, were the last units operated by steam.

Jan 1, 1958