Search Documents

Apparently there is little inclination on the part of mining engineers to supplant the transmission of power by compressed air with it's formidable rival, electrical transmission. No doubt there are many advantages to be claimed for compressed air that render it parculiary well suited for the conditions which characterise underground work.

Jan 1, 1902

During the drilling campaign conducted between October, 1942; and May, 1943, to prove the extent of the scheelite deposit worked by King Island Scheelite N.L. at Grassy, King Island, Tasmania, 35 holes were drilled and 606 samples recovered and assayed for their content. Of these, 238 came from outside the limits of the orebody and were for the most part barren, although a few contained some scheelite. The present statistical analysis is made only of the 368 samples taken from diamond-drill cores of the orebody itself.Drilling Pattern and Sampling MethodsFrom the purely statistical viewpoint, it is realised that methods employed in selecting sites for diamong.-drilling, and of collecting samples from drill cores, do not give a completely unbiassed set of data for analysis. Fig. 1 is a sketch plan showing the relativepositions of the drillholes, which were inclined at an angle of depression of 50 deg. The pattern does not conform to a properly randomized and' regularly-spaced grid, the positions of the later holes being determined by the results obtained from previous holes.Statistically, the bias is, therefore, favourable. The unequal spacing of the drill holes and the lack of uniformity in direction of the lines along which the holes were drilled are unsatisfactory from the mathematical viewpoint; but it is realised that these irregularitiesare difficult to avoid in determining by the most economical methods the extent of such an orebody, and are dictated by geological rather than mathematical necessity.Sampling, also, is lacking in complete uniformity. Each sample is approximately 10ft. in length. However, owing to the fact that 100% recovery of core is rarely achieved, and actual lengths of samples taken are ,primarily governed by the length of the drill runs,and secondarily by lithological changes, there is a considerable amount of variation in the sample length.AssayingWith the exception of 28 samples from three drill holes all samples dealt with in this paper were assayed in the Melbourne University Ore-Dressing Laboratory of the Commonwealth Scientific and Industrial Research Organisation. These assays were given to the nearest 0.05% WOg as it was considered that more accurate determination was not possible. This fact has been taken into consideration in the frequency analysis below. The 28 assays determined by the Tasmanian Mines Department were given to the nearest 0.01%.

Jan 1, 1950

Wet mining of auriferous gravels at L & MÆs Waikaka operation in Southland creates spoil dumps derived from stripping of a clay rich overburden, tailings from past dredging and the processing of auriferous sands and gravels. Over recent times, spoil dumps have slumped on six occasions, threatening the viability of the wet mining operation. Close examination of slump morphology, coupled with the sequence of material placement and rate of dumping suggested a mechanism associated with undrained failure of a 2 m layer of silt and sand tails forming the base of dumps.Commencing with some information on the geotechnical properties of source overburden, back analysis of failure morphology and sequence and development of undrained loading conditions from first principals, the most likely failure mechanism and factors controlling failure were defined. Based on analysis results, a scheme to stabilise the lowwall dumps was developed and implemented, augmented by continuous monitoring of pore pressures in the basal wet tails, and laboratory testing for confirmation of computed material properties.Lowwall spoil stability has improved since implementation involving changes to the method of spoil loading, and modification of wet tails composition to improve permeability and drainage of the basal wet tails under load. The method and approach to prediction and verification of failure mechanism provide a sound basis for continued mining of deeper auriferous gravels.

Jan 1, 2002

Variations in delay timing can have a marked influence on blasting effectiveness and, hence, on total production costs. In single-row bench blasts, delay firing is invariably more effective than simultaneous initiation. In single-row delayed blasts, there is an optimum inter-hole delay above and below which inferior blasting results are obtained. This optimum delay is equal to the time required for each charge to just effectively detach its quota of the burden. The inter-hole delay should seldom be less than 4 ms.m-l of burden.In multi-row blasts in which holes in a given effective row are fired on the same delay, the entire burden on any effective row should be detached from the rock mass just before charges in the next effeotive row detonate. Delays shorter than this give inferior blasting results and an increased likelihood of environmental and slope stability problems. If the inter-row delay is too long, cut-offs can occur, especially where the delay unit is located outside the blasthole. For a surface delay system, the optimum inter-row delay usually varies between 4 ms.m-l and 8 ms.m-l of effective burden. The number of rows that can be fired effectively with surface delay systems (in a single blast) is limited by the threat of cut-offs. Greater interrow delays and a larger number of rows per blast can be fired to advantage with down-the-hole delay systems.There are practical limits to the timing accuracy of all available delay systems. The existence of delay time variability should be recognized and duly considered in the design of blasts.The relationship between delay timing and blasting vibrations is not discussed.

Jan 1, 1977

By Hannan J. C

In New South Wales, development applications for major coal mining proposals are determined by the Minister for Planning and Environment and applications for mining leases and other mineral titles are dealt with by the Minister for Mineral Resources. The environmental conditions placed on the development consent, the coal mining lease and the approvals and licences under the pollution control legislation, amount to a substantial component of any new project's planning and commissioning considerations.An outline is presented of the framework within which various approvals are granted and conditions for environmental management are imposed upon mining projects. The principles and concerns, as perceived by the regulatory authorities, on which the majority of approval conditions are based are also outlined.No attempt has been made to analyse the extent to which these principles or standards are achieved in practice, nor to discuss the degree to which some of the conditions are achievable with the current status of technology and economics in the coal industry.

Jan 1, 1987

Experiment of Improving the Quality and Decreasing the Impurity of Titanium Concentrate in Panzhihua Mine in China

Sep 13, 2010

This paper sets out to examine the possible relationships between three factors, they are, the rate of growth of world production of minerals, the growth of Australian production and the growth of scientific and engineering knowledge.The first two are quantified, in terms of tonnes and value. The third, an abstract concept "knowledge", requires to be quantified, in terms of manpower.A mathematical model, which has general application, was derived to demonstrate certain axiomatic premises and to define, more precisely, basic concepts related to the philosophy of knowledge.Finally a summary is made of education-cum-industry issues.

Jan 1, 1981

By Kelsall D. F, Trahar W. J

The size by size batch flotation behaviour of copper activated sphalerite from synthetic mixtures with quartz was determined. In terms of recovery of sphalerite, the size fractions could be grouped into coarse, intermediate, and fine ranges. The behaviour of the coarse and fine ranges was significantly poorer than that of the intermediate range in both the extent and rate of flotation.Each size fraction had a fast and a slow floating component.The main effect of changing the copper sulphate addition was to alter the proportion of any size fraction which was fast floating. No correlation could be found, between the amount of copper on the spha:lerite andeither the flotation rate of the mineral or the amount of copper added to the system. It was found that fine particles did not appear to consume greatly disproportionate amounts of copper sulphate during conditioning. A modified conditioning procedure was found to lead to a higher rate of flotation and recovery of coarse sphalerite and to make poss1ble substantial savings of copper sulphate.

Jan 1, 1975

By C Hall, J L. Mauk

New 40Ar/39Ar dates of vein and wall rock adularia from seven epithermal deposits and one porphyry copper prospect help constrain the ages of mineralisation in the Hauraki Goldfield. Vein adularia from the Paritu region yielded a single 40Ar/39Ar plateau date of 16.315 ¦ 0.066 Ma. Five 40Ar/39Ar plateau dates of three samples of vein adularia from the Opitonui deposit overlap within error to yield a preferred age of 13.149 ¦ 0.016 Ma. Two samples of vein adularia from the Night Reef at the Broken Hills deposit yield exceptionally flat 40Ar/39Ar plateaus, and all dates overlap within error to provide an age of 7.121 ¦ 0.010 Ma. Two 40Ar/39Ar plateau dates of one sample of vein adularia from the Wharekirauponga deposit overlap within error to provide an age of 6.318 ¦ 0.061 Ma. Four 40Ar/39Ar plateau dates of three samples of vein adularia from the Maratoto deposit overlap within error to provide an age of 6.411 ¦ 0.022 Ma. Two samples of adularia from altered wall rock at the Sovereign deposit yield three 40Ar/39Ar plateau dates that range from 6.547 ¦ 0.021 to 6.806 ¦ 0.028 Ma. This suggests that mineralisation formed around 6.6 Ma, but the results are complicated because the adularia contains minor illite that post-dates adularia formation. Results from the Karangahake deposit are complex. Two samples of vein adularia yield three 40Ar/39Ar plateau dates that range from 6.116 ¦ 0.116 to 6.901 ¦ 0.101 Ma, whereas one sample of wall rock adularia that contains minor late illite yields two 40Ar/39Ar plateau dates that overlap within error to provide a date of 5.734 ¦ 0.041. The range of dates indicates that more work is necessary to understand the history of mineralisation at this deposit. Two samples of vein adularia from the Tui deposit yield four 40Ar/39Ar plateau dates that overlap within error to provide an age of 5.714 ¦ 0.017 Ma. These results confirm previous work that indicates that the ages of epithermal deposits young southward in the Hauraki Goldfield. These results are also consistent with previously postulated different ages for deposits hosted in Kuaotunu Subgroup rocks in the northern goldfield (>10 Ma), and deposits hosted in Waiwawa Subgroup rocks in the southern goldfield (7.1 to 5.7 Ma).

Jan 1, 2005

EARLY in 1911 the Public Service Board of New South Wales suggested the advisability of inaugurating a School of Mines at Broken Hill, arid made inquiries to determine how such an institution should be conducted. He, the author, believed the Board, as a result of the inquiries, was in favour of the project being worked in conjunction with the Technical College, and hoped to be ready to receive students at the commencement of 1912. That the inauguration has not yet taken place is probably due to the vast amount of consideration and preparation that a new departure of the sort would require. At the present time New South Wales or, to speak more broadly under the same denunciation, Australia is not at all suitably catering for the technical training of young men to provide the increasing demand for officers to work the valuable mines within its territory...

Jan 1, 1912

By Lees M. G, Vitnell B. W

The post-war need to increase coal production promoted an intensive drilling campaign. Ineffectiveness in core recovery inclined the coal industry towards percussion drilling rather than diamond drilling. The Joint Coal Board, recognising the greater potential of core drilling, has actively encouraged improvement in techniques and equipment. One outstanding need was a barrel which, over and above other improvements being achieved, would permit recovered core to be examined before it had been subjected to the increased fragmentation and displacement which to date has been inevitable except in core which has been drilled in solid sticks û as New South Wales coal rarely can be drilled. In conjunction with Triefus Pty Ltd a barrel with a split inner tube has now been evolved, as a result of which, core can be more accurately logged, division in to lengths for analysis more aptly made, any core loss more reasonably allocated to appropriate plies, and a greater percentage of core recovered û of the order 95 per cent and more. The one half of the split inner tube is lifted from the other and the logging completed before the core is disturbed.

Jan 1, 1957

By D Pilone

The Tyrrhenian micro-nodules, findable at low depths (200/600 m under s l) are a reasonable reserve of manganese. They can be easily and cheaply recovered but do not contain valuable metals as in the case of oceanic nodules. In this work a hydrometallurgical process for manganese recovery from Tyrrhenian nodules is presented. The studied treatment includes the following operations: magnetic enrichment, reducing leaching, leach liquor purification and electrowinning . The study shows that the most important step in the process is the preliminary manganese enrichment. It can be done directly on the platform reducing not only the transport cost, but also the residue mud in the metallurgical plant. The leaching parameters such as status and size of nodules, temperature, composition of leaching solution and S/L ratio have been investigated. After purifying the leach liquor by iron precipitation as ammonium jarosite , the conditions to electrowin manganese have been investigated. The yields of both manganese leaching and iron precipitation together with current efficiency and specific energy consumption in the electrowinning step are given.

Jan 1, 2000

By Baxter J. L

Post-tertiary training programmes have been designed and produced for geologists at different levels of understanding and expertise in the relationship between gold mineralization and shear zones. A workshop format was used as it allowed both clients and facilitators to participate in the learning process. Evaluation by facilitators and participants refined the workshop programme as an effective skills oriented learning process. The general observation is that post-tertiary training in small, interactive, practical, learning oriented groups is far better than lecture oriented short courses for developing skills based learning. The evaluation indicates that the process in post-tertiary training must include aspects which are both useful and used.

Jan 1, 1989

When the Mining Bill came before the Victorian Legislature not so many months ago, the question arose whether mining managers required education, and to what extent. Some members of the House expressed themselves in a way which appeared to leave the impression that mining managers would be all the better if they were not brought up in a scientific school.To try and prove what we owe to science I will give a short history of colonial mining from the earlier period to the present time and compare results.I believe I am right in saying that South Australia is the pioneer colony in mining and to her belongs the credit of not dnly being the first mining colony, but also that her beginning turned out so successful, as the history of the Burra Burra copper mine will testify. At about the same time a little galena mining was carried on nearer to Adelaide, but as this did not prove a success and was only worked by tributing parties, little notice was taken of it.

By J Wallis

The stability of a raise bore is often assessed using the rock mass classification system published by McCracken and Stacey as a modification of the Q system. Often the assessment is done using a spreadsheet to manipulate geotechnical log(s) of boreholes. This paper discusses the inherent difficulties with this approach. Recent work by others to provide guidelines to the classification system is discussed. A recent example of the design and raise bore performance at Macraes Gold Mine, New Zealand is presented. A key issue is that a visual assessment of the drill core and/or core photographs is necessary to æground-truthÆ the classification.

Jan 1, 2008

By R Fury, I Skepper, D White, G Miller

Although the Pressure Acid Leaching (PAL) of nickel laterites has been conducted at Moa Bay, Cuba, since the early 1960s, the commissioning delays generally encountered by the æsecond generationÆ of PAL lateritic nickel producers in the late 1990s have demonstrated the potential complexity of the PAL process and the importance of technical risk management in maximising the realised project value. This paper describes some of the strategies used by the Ravensthorpe Nickel Project (RNP) to manage the technical aspects of the Ravensthorpe project risk. Central to these strategies is the use of Front End Loading (FEL) to deal with issues early in the development phase, when changes to the project structure can be made most effectively and cheaply. Such an approach requires a management philosophy that recognises risk as a potential cost, which accepts responsibility for dealing with risk, and which is prepared to provide adequate resources for risk management.

Jan 1, 2004

By B Leisemann, M Watkinson

Coal augering is an ideal method for recovering coal from the highwalls of open cut coalmines. Coal augering is a simple process whereby additional flights are added to the auger cutting head and auger holes are drilled at 1.9 m diameter up to 200 metres deep. Traditional monitoring was located at the mouth of the hole and if methane was encountered above two per cent, inert gas was delivered into the mouth of the hole to deplete the oxygen content at the auger cutting head below 12 per cent. The auger operator was asked the question ‘how do you know that this is the case?’ Trials were undertaken to prove that the oxygen content at the cutting head did drop below 12 per cent (the lowest limit for methane to ignite, also known as the oxygen nose point). Initial trials showed that the oxygen content in the mouth of the hole did not drop below 12 per cent and modifications were made to hold the inert gases in the mouth of the hole so that the auger flights could take this inert gas into the hole. In-hole monitoring, after completion of mining and after extracting the auger flights, showed that the atmosphere quickly returned to fresh air. In-hole monitoring was also tried during the augering process and yielded valuable results. This paper will discuss the results of the monitoring, information on the gas results obtained and the methodologies used to optimise the oxygen content at the auger face.CITATION:Watkinson, M and Leisemann, B, 2017. Inertisation of coal augering holes, in Proceedings Australian Mine Vent Conference 2017, pp 293–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By C S. Szentesy, K Howie

The Rosia Montana gold deposit is located within the æGolden QuadrilateralÆ area in the Apuseni Mountains of Transylvania, Romania. The deposit is situated approximately 85 kilometres north of the regional centre of Deva, within the province of Alba, at elevations of up to 1100 metres above sea level. The Rosia Montana deposit contains a current resource of 344.07 million tonnes at an average grade of 1.3 grams per tonne (g/t) gold (Au) and 6.0 g/t silver (Ag) for a total (measured, indicated and inferred) contained resource of 14.29 million ounces of gold and 67.00 million ounces of silver. The resource was calculated using a 0.6g/t Au cut-off, a 10 x 10 x 10 metre block size and multiple indicator kriging. The low sulfidation style epithermal mineralisation at Rosia Montana is hosted within Tertiary age dacite intrusions and related vent breccias. Mineralisation is generally disseminated and associated with silica, adularia, illite, pyrite and carbonate alteration of host rocks, with minor late carbonate-base metal veins. Precipitation of precious metals is generally considered to have occurred as a result of over-pressurization, boiling and subsequent brecciation. The dacite intrusions are hosted in Cretaceous shallow marine and deltaic shales and slates, which overlie older Paleozoic sedimentary and metamorphic rocks within uplifted sections of oceanic sea floor.

Jan 1, 2002

By Vaughan J. P

The Pegmont deposit is a stratiform Pb-Zn sulphide body occurring in a thin, iron-rich metasedimentary unit situated near the top of the Kuridala Formation, a part of the Mary Kathleen Group of the Middle Proterozoic"Eastern Geosyncline" succession of the Mount Isa-Cloncurry district. The deposit appears to have developed in a shallow basin or depression on a sea or lake floor.Detailed chemical and mineralogical study of seven diamond drill cores through the ore horizon shows that in addition to galena and sphalerite the orebody contains a large range of iron-rich silicates and aluminosilicates.Further, five drill cores selected to represent a section from basin centre to basin edge exhibit clear and systematic chemical and mineralogical changes in the ore horizon in both a vertical and, most importantly, ill a lateral sense.Reconstruction of the sedimentary environment of the ore horizon as a whole shows this to be a silicate facies of a phosphatic, manganiferous iron formation or, more accurately, of "ironstone" in the sense of James (1966, U.S. Geol. Surv. Prof. Paper 440, chapter W).On the basis of both mineralogy and chemistry this silicate facies may be subdivided into three microfacies according to the dominant iron silicates characteristic of each: a fayalite microfacies, a hornblende-clinopyroxenemicrofacies, and a garnet microfacies. Significant Pb-Zn sulphide concentrations are confined almost entirely to the fayalite microfacies.

Jan 1, 1979

An assessment of methods currently available for the accurate determination of low concentrations of platinum in ores and mineral concentrates indicated that prior treatment of the sample by fire assay procedures is necessary. To enable rapid determinations to be carried out, instrumental methods applied to the metallic bead produced from the fire assay treatment have been evaluated, considering maximum flexibility for concentration variations, minimum chemical operations, and adequate sensitivity.Atomic absorption spectrometry proved suitable, giving solution determination limits of 0·4 p.p.m. Pt, 0·1 p.p.m. Pt, or 0·06 p.p.m. Pt under various extraction conditions using aqueous and organic agents. Thesedetermination limits related to 1 assay ton of sample (32·67 g) produced easily readable and accurate readings within the range of platinum contents (0·03-2·0 p.p.m.) of economic interest in deposit evaluation and prospecting. The technique shows promise of also being suitable for determination of palladium and gold.

Jan 1, 1970