Search Documents

By L D. Munro, S A. Jackson

This paper provides a logical approach to developing a TSF design concept through: • Identifying key properties of tailings and containment structures; • Reviewing underlying principles for effective operation; • Showing how these apply to select an appropriate TMS; and • Demonstrating how to align the TMS to site-specific constraints and TSF design. This approach follows a path of rigorous data analysis independent of discharge parameters (whether low-density slurry, paste or cake disposal) to select the most cost-effective and sustainable approach for any given material or site.

Jul 1, 2021

By T Sprague, D Pateman

"The Gosowong Gold Project is owned and operated by PT Nusa Halmahera Minerals (PT NHM), an Indonesian company 75 per cent owned by Newcrest. It is located on Halmahera Island, in the North Maluku Province of the Republic of Indonesia, approximately 2450 km north-east of the national capital, Jakarta (Newcrest, 2017).Kencana is one of two underground gold and silver mines at the Gosowong Operation where ground conditions vary from competent to very poor. Development headings occurring in poor rock mass conditions require high capacity ground support including long tendon cable bolts. Manual installation of cable bolts in these development headings has been a time consuming process due to borehole collapse, blockages requiring subsequent re-drilling and a minimum eight hour grout curing time interval. The installation of cable bolts including the setting, plating and tensioning can impact the critical path for development heading advance resulting in development cycle delays.A review was conducted by PT NHM on current industry practices for alternatives to manual cable bolting. PT NHM subsequently approached Minova to assist with the development and trialling of self drilling anchors (SDAs) installed using jumbos with a rapid setting pumpable resin, CARBOTHIXTM. A series of system development trials were conducted and a reliable bolting system was developed utilising the existing jumbo drilling fleet with minimal required modifications.The system developed was a ‘one pass’ bolting process to install and grout SDAs using a two component resin with a remote, mechanised system. Improvements achieved from the system include: eliminating hole closure issues and more immediate support in poor rock mass effectively reducing personnel exposure to poor ground conditions by removing the requirement to access the drive backs reducing grout set time with full installation times for 6 m SDAs averaging 25 min.The resin grouting system has now been successfully implemented to effectively manage areas of poor ground conditions and to accelerate advance rates in high priority headings.CITATION:Pateman, D and Sprague, T, 2017. Development and implementation of a long tendon bolting system utilising resin grouting technology, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By K Gardner, R Fraval, V Singh

Using new technology to create optimised infill drill programs in underground or open pit settings, it is possible to quantify the value of a drill program. The computer designed programs are optimised to uplift the most amount of resource possible into the specified resource classification, while honouring geological, spatial, equipment and budgetary constraints. When designing ‘by hand’ balancing all these factors is a time-consuming effort with no real way to determine metrics on ‘how good’ a program will be. The optimisation considers many factors allowing geologists to apply critical thinking and domain knowledge to constrain the optimisation, letting the computer do the heavy lifting of determining hole placement. Once programs have been created, they can be integrated into a production schedule. This is a critical step in determining the correct sequencing and balancing of resource availability and seeing how a program will interoperate with other tasks in the mine. For example, if drill drives are a requirement for part of the program, will they be developed in a time frame that is useful for the goals of the program? Do we risk drilling infill holes too late to add value? Do we put production at risk by not classifying parts of the model ahead of time, thus adding to uncertainty? Using software to assist with optimising and scheduling of drilling is a useful technique to save the geologists from the mundanity of manually designing drill programs and puts metrics around the effectiveness of a program and has the potential to add quantifiable value to a program. Examples will be presented that demonstrate the effective use of drill hole optimisation, comparing manual designs with optimised designs, as well as the examples that show the effective use of scheduling.

Mar 22, 2022

By P York

The study commenced in October 2012, to understand the basic ecology of the spotted-tailed quoll (Dasyurus maculatus) and to confirm whether the species utilise previously mined land on the Mt Owen mine site that was rehabilitated in 1996 to 2011, as part of their home range. The spotted-tailed quoll is a widely distributed marsupial carnivore that is listed as rare or threatened in every state in which it occurs. The species is a forest-dependent marsupial carnivore that occupies a wide range of habitat types (Long and Nelson, 2004).The first part of the study involved trapping a spotted-tailed quoll and fitting the individual with a combined global positioning system / ultra high frequency (GPS/UHF) radio-transmitter collar (Telemetry Solution – Quantum 4000E). The benefit of the GPS/UHF collar is that it records locations (or fixes) at intervals programmed by the user. The UHF component allows the researcher to locate the individual at a frequent interval, and the Quantum 4000E also has a remote download function, enabling the GPS data stored in the collar to be wirelessly transmitted between the collar and researcher. The benefit of this new technology is that the animal does not need to be repeatedly captured to retrieve the GPS data.Daytime searches are also undertaken using the UHF receiver to locate the individual and locations of daytime denning and latrine sites. The location of each den site is recorded using a hand-held GPS. Data downloaded from the GPS collar is then imported and mapped using computer software program ARCGIS (geographic information system), to overlay the data points onto aerial photography.Results demonstrate that threatened species will utilise rehabilitation areas post mining. The data presented will be used to develop a greater understanding of threatened species ecology in and around rehabilitated areas, which will assist in the planning and design of native forest rehabilitation areas.CITATION:York, P, 2014. Mt Owen Mine spotted-tailed quoll study, in Proceedings Life-of-Mine 2014 , pp 591–596 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By S Mundell, J Armstrong, M Evans

"Automation is a common goal within the coal industry for reasons such as efficiency, reliability and sustainability. However, it requires standards and frameworks so business systems can communicate effectively. Automation of sample analysis processes has been difficult to establish due to a lack of direct business system communication between commercial laboratories and mining companies. This has resulted in manual procedures that have contributed to problems relating to analysis instructions, sample identification, results formats and visibility of status.These problems result in loss of data and confidence in data validity, loss of process efficiency and inability to react to issues. An Australian Coal Association Research Program project (Evans, Armstrong and Arboleda, 2014) has addressed these issues through the Coal Quality Data Exchange methodology for direct business system communication between coalminers and commercial laboratories to optimise the transfer of coal quality data.The benefits to the coalminer of the framework are:increased clarity and auditability of what is being sent to the laboratory and what was requestedreduced potential for error introduced through manual transcription tasksincreased speed of loading of analytical results to the customer Geoscientific Information Management Systemimproved turnaround time for analytical resultsincreased knowledge about what took place in the laboratory with respect to the determination of the analytical resultsincreased visibility of the status of a ‘work order’. The benefits to the technology companies and commercial laboratories is a common framework on which to build a sustainable solution that gets away from the multitude of formats catered for today and time consuming manual processes. The common framework significantly advances the future possibilities for the automation of sampling and analysis processes in a production environment.CITATION:Armstrong, J, Mundell, S and Evans, M, 2014. Automating communications between laboratories and mines – a case from the coal industry, in Proceedings Ninth International Mining Geology Conference 2014 , pp 351–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By J R. Robinson

Prior to mine development, exploration drilling within the Luise Caldera on Niolam Island encountered gold mineralisation to the northwest of the main Minifie and Lienetz orebodies. This mineralisation was referred to as the Kapit orebody, and ten diamond drill holes were subsequently completed over the area to investigate its economic potential. Several significant mineralised intercepts were returned. These were interpreted using the orebody model developed for Lihir at that time which invoked a strong horizontal control to mineralisation. Additional consideration was given to the elevated geothermal temperatures encountered, the proximity of the mineralisation to the ocean, and its perceived depth below sea level, resulting in the Kapit area being given a low priority for follow up investigation. As a result, no further work was completed over Kapit until recently. The Kapit orebody was the target of an intense diamond drilling programme during 2002/2003. Data from this latest round of drilling has significantly improved understanding of the mineralisation and associated geology. The significant orebody now delineated at Kapit substantially differs from past interpretations, and the latest data has upgraded its economic potential. A resource estimate and other critical studies completed in 2003 enabled an updated reserve statement to be issued in February 2004 including the Kapit mineralisation for the first time. Total Probable Reserves at Kapit stand at 25.2 million tonnes (Mt) at 5.28 grams of gold per tonne (g Au/t), for a total of 4.3 million ounces (Moz) of contained gold.

Jan 1, 2004

By É Lèbre, G Corder

The circular economy concept, as defined by the Ellen MacArthur Foundation (2015) and quoted by the recent International Council on Mining and Metals (ICMM) Guide to Responsible Sourcing, calls for shifting industrial systems from a linear take-make-waste model to a circular model (ICMM, 2015). In this model products are designed to optimise product and material recovery and reuse, and by-products of one system are used as inputs into other product systems. While the mining industry to date has made a limited contribution to the circular economy, the current market conditions, which are prompting calls for greater innovation, make the timing right for the industry to boost its contribution by utilising and generating value from mining waste, or making it available as a feedstock from which other industries can harness value.The first part of this extended abstract discusses the way the circular economy concept can be adapted to metal mining activities, contributing to a more sustainable resource extraction at the mine site level. The second part of this extended abstract presents a circular economy based framework revolving around non-renewable resources conservation. The third and final part examines the application of the framework to the Mount Morgan mine in Central Queensland.CITATION:Lèbre, É and Corder, G, 2016. Utilising mineralised mining waste – contributions to the circular economy, in Proceedings Life-of-Mine 2016 Conference, pp 132–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By J Ireland, S Rose

The main outcomes of mining grade control include defining the boundary between ore and waste and then categorising the ore according to which stockpile it should be sent. A typical workflow includes using general mine planning software (GMP) – such as SurpacTM, VulcanTM or CAE StudioTM – to create three-dimensional wireframes of mineralisation domains, which are used to flag the relevant samples of interest and constrain estimation during block modelling. Creating the wireframes is a time-consuming process, requiring reasonable software skills, patience and an eye for detail. The interpretations can be subjective; indeed, even the same geologist will give different shapes if presented with the same data at different times. The process can become particularly tedious when trying to carry out updates due to new data. It can also be difficult to test the effect of alternative interpretations or grade thresholds because of the time constraints in production.There are now several implicit modelling tools available, either as standalone programs or as add-on modules to existing GMP. In this paper, the authors develop a workflow using implicit modelling methods to show how grades and geology can be rapidly interpreted to provide effective domains for grade estimation. The paper includes case studies from open pit gold mines. The implicit modelling approach can save several days of interpretation work for each grade control drilling campaign.CITATION:Rose, S and Ireland, J, 2014. Implicit modelling applied to grade control data, in Proceedings Ninth International Mining Geology Conference 2014 , pp 115–122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Drinkwater DJ, Watsford RMS, Johnson NW, Munro PD

This paper describes the use of modelling and simulation techniques in the analysis and optimisation of grinding circuits at the Lead/Zinc Concentrator of Mount Isa Mines Limited.The objectives of the studies were to: -1. improve primary grinding circuit performance by reducing the production of -0.006 mm galena fines.2. maximise the fineness of grind in the second existing grinding power and pumping capacitie The study has shown that quantitative models can operations. The models described plant operation,,and simulated the effect of process changes on plant performanc The use of automated scanning electron microscope technology tcliberation characteristics of the major minerals in the Mount isa Lead/Li ore is also described.

Jan 1, 1985

The new law on Environmental Protection and Management (Republic of Indonesia Law 32 of 2009) was passed by the Indonesian parliament in September 2009. This law aims to protect Indonesia's rapidly degrading environment by providing tougher provisions for both polluters and law enforcers. In doing so, the law introduces a number of new constraints and potential business risks that will affect all companies in Indonesia, particularly mining companies. Some of the newly introduced concepts follow.   Mining companies will now require an environmental license, issued by the Minister of Environment or local counterparts. This license is a prerequisite for all other business and operational permits. The Minister can revoke the environmental license at any time in case of an environmental incident or dispute. Mining companies may be exposed to additional environmental taxes and bonds besides already existing reclamation and mine closure bonds.   There is an increased risk of environmental lawsuits, due to more stringent controls on one side and greater protection for NGOs on the other side who make claims, false or true, against the company. Company executives and managers can be sued and they will be held accountable if environmental degradation has indeed occurred due to the company's activities.   Companies may face increased liabilities due to a change in the definition of contamination. The new definition is more stringent (and on occasion may prove too stringent to be practical); it also provides little room for flexibility in its application.   As implementing regulations are prepared over the coming two to three years, mining companies will need to adjust to the new law. A proactive approach is needed to minimise risk. Recommended actions include: upgrading existing environmental impact assessments to a higher standard; conducting baseline studies and thoroughly documenting environmental conditions on a regular basis; closely tracking regulatory changes, especially the forthcoming implementing regulations on the new environmental law; and regularly engaging key government and community stakeholders on environmental issues.

Jun 1, 2010

By A Morris

The Express Rail Link (XRL) will provide high-speed rail services from Hong Kong to Guangzhou and a connection to the national high-speed passenger rail network serving major cities throughout Mainland, China. The HK$ 67 B (NZ$ 11.5 Billion) project is of great strategic importance for Hong Kong and is being implemented to a very tight schedule, from early 2010 with completion targeted for 2015.The works include a 15 platform terminus station in West Kowloon, 26 km of twin track tunnels from the terminus to the Hong Kong/Shenzhen boundary at Mai Po, tunnel vent shafts/adits/emergency rescue siding and a stabling siding facility. Trains on the Hong Kong section are intended to operate at speed up to 200 km per hour and up to 350 km per hour on the Mainland section.This presentation will provide an overview of the entire XRL project, with a focus on the challenging geotechnical and spatial constraints on the tunnel works. This is an abstract only. No paper was prepared for this abstract.

Mar 8, 2011

By J Balzary, A Mohais

Dynamic market and operating conditions, coupled with an environment in which multiple objectives and trade-offs are common, pose major challenges for planners and schedulers working in any mining entity. Many mining companies recognise the need to shift from a siloed mining-focused push model to an integrated value chain, demand-driven approach, but there are still fundamental barriers in business process and the supporting technology preventing a consideration of end-to-end optimality.This paper presents some elements of experiences working with companies to adopt such advanced approaches. In addition to algorithmic elements, an approach to phased and gradual deployment of progressively more sophisticated optimisation models is described. From a practical software adoption perspective, it is believed that this last concern is also of primary importance. Next generation approaches to the optimisation of complex bulk commodity demand chains, namely iron ore and coal are presented, with case studies in the world’s largest integrated operations in Western Australia and Queensland from the raw material mined through to market. Utilising accurate simulation models supported by metaheuristic optimisation techniques, a range of ways to engineer a dynamic decision support framework that can adapt and change with the inevitable changes in commodity markets is explored. Objectives such as total revenue, margin, cost, NPV, throughput, asset utilisation, contractual penalties and bonuses, and energy consumption can be managed simultaneously across the mine, plant, logistics network, port operation, shipping and sales domains.CITATION:Balzary, J and Mohais, A, 2014. Consideration for multiobjective metaheuristic optimisation of large iron ore and coal supply chains, from resource to market, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 213–222 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By G Brudek, P Elestedt

Schalker Eisenhütte und Maschinenfabrik GmbH, Nordic Minesteel Technologies and Bombardier Transportation have developed an evaluation tool that considers the main cost drivers of the rail, truck and conveyor haulage systems on the market today. In almost every circumstance, the advantages of a haulage solution are clear. A haulage system is outlined that is fully automated, including driverless operation, and that provides increased tonnage, safety and equipment life and reduced maintenance downtime. The haulage system has been implemented by a number of companies, including Codelco, LKAB and Freeport’s Grasberg mine. CITATION:Brudek, G, Elliott, R P and Elestedt, P, 2016. Moving mORE for less, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 535–542 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R Hartner

Digital optical microscopy (DOM) and automated SEM-based (ASEM) mineralogy systems (MLA, QEMSCAN) have experienced significant developments within the last decade. However these developments have been independent from each other and the two mineralogical techniques have so far not yet been integrated to combine the strengths and technical benefits of both analytical platforms. This detailed comprehensive mineralogical information is critical support for geometallurgy.Major hardware and software advances in DOM in the last few years have provided important new capabilities with potential applications to automated mineralogy. These technological advances have been largely driven by sectors outside mining (eg medical pathology) and have not yet been widely adopted within the minerals industry. The advent of DOM offers significantly more automated mineralogy capabilities than traditional expert-mineralogist driven optical microscopy. This is based on advances in automated image acquisition, high resolution cameras for digital imaging, imaging of large areas through mosaic options, integration of multiple layers and application of advanced image analysis techniques.Ongoing research involves combining the outputs of DOM and ASEM-based microscopy to create new capabilities for integrated microscopy based on development of advanced cross-platform image fusion and data integration between DOM and ASEM (exploiting the benefits of both analytical platforms). This requires non-linear image registration and transfer of mineralogical identification from ASEM to DOM systems using sophisticated image manipulation and data analysis software.Examples will be given of image fusion and data registration for a range of different ore types. Image fusion techniques are demonstrated using a porphyry copper deposit sample where sulfides and precious metals are classified using the MLA and gangue mineralogy obtained from DOM images. Data integration enables creation of a library containing optical property variability information for minerals identified by the MLA; thus reducing the reliance on skilled mineral identification by supplementing human interpretation

Sep 5, 2011

By X Zhang, Y Zhu, P E. Ngoepe, P P. Mkhonto, W Xiong, L Han, L Lu

The triazine molecules have not been given much attention and they are potential collectors that may positively impact the mineral processing industry. The adsorption of triazine as collectors such as sodium 2,6-dithio-4-butylamino-1,3,5-triazine (SDTBAT) on pyrite form a basis in design of flotation collectors that may be applicable in a wide range of sulfide minerals. The SDTBAT collector was compared with the sodium normal butyl xanthate (SNBX) and sodium normal butyl dithiocarbamate (SNBDTC). All collectors were adsorbed in their neutral form containing sodium on the pyrite (100) surface. The computational calculations found that the adsorption energies followed the order: SDTBAT (-300.35 kJ/mol) > SNBX (-186.10 kJ/mol) > SNBDTC (-163.78 kJ/mol). It was observed that the SNBX and SNBDTC adsorbed through the S atoms, while the SDTBAT adsorbed through the S atoms and N atoms onto Fe atoms. It is clear that the SDTBAT had a strong binding energy which is attributed to the presence of the triazine group that is electron depositing to the active S atoms compared to the SNBX which possessed the oxygen that is electron withdrawing. Moreover, the SDTBAT collector was found to bind stronger than the xanthate. This was complimented by microflotation tests that showed fast floating and higher recoveries of pyrite when using the SDTBAT collector than the xanthate and DTC. This clearly demonstrated that the SDTBAT is a potential collector to replace the xanthate collector due to its high selectivity and flotation power.

Aug 24, 2022

By R G. Moreby

The purpose of this paper is to provide the rationale for decision making when considering the use of three heading gate roads in Australian underground coal mines.There are currently 30 underground longwall mines in Australia with all but two employing two heading gate road longwall layouts. The volumetric capacity of these two heading ventilation circuits is evidently viable in typical block lengths and in low to moderate gas regimes. However, in gassier regimes, potential longwall production rates of 10 Mt/a, and or where block lengths are being extended to well beyond historical norms, a conventional two heading U circuit may not be adequate. Other than seam gas emission, block length and production dependent heat loads together sealed area management requirements also have to be considered.The two mines currently employing three heading gate roads have the opportunity to revert to two headings at any time but, based on operational experience to date, have not done so due to the consequential reduction in gas management capacity and lower production rates associated with gas delays and limitations on tailgate access.Although there are a number of alternative two heading longwall circuits available and employed worldwide, the custom and practice of promoting inert goaf atmospheres in most Australian coal mines to mitigate the risk of catastrophic gas explosions and spontaneous combustion often prevents the use of gas loaded bleeder systems. In this respect, Australian underground coal mines may be considered the safest in the world.The current situation is that three heading gate roads have been proven successful in Australian conditions, albeit at additional cost, where two heading ventilation circuits cannot manage net seam gas emission to the ventilation system at the production rates required. In this respect, a further important driver for decision making is the short to medium term value of CO2-e emission taxation in Australia.CITATION:Moreby, R G, 2013. The rationale for use of three heading gate roads in Australian underground coal mines, in Proceedings The Australian Mine Ventilation Conference , pp 13-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By A Whaanga

The use of photogrammetry has greatly increased the accuracy of 3D mapping underground. However, this has not reduced the need or desire for geologists to produce plans and sections showing an interpretation of the mapped geology. At the Waihi Underground Gold Mine, a hybrid solution has been developed that utilises the accuracy of photogrammetry and mapping onto face photos with the CAD-based Deswik.MappingTM functions to create plan and section maps. These have the benefit of looking like traditional paper maps but are more spatially accurate and richly attributed with metadata that can be filtered and exported to downstream processes. Deswik.MappingTM is a tablet-based solution that allows the geologist to map digitally with a stylus. Automation is utilised for the updating of survey as-builts, approved designs, drill holes, geological mapping, vein interpretations and mine work areas, reducing the requirement to print out maps at various locations and scales. Having 3D mine software on a tablet device provides a wealth of features not available when using paper: scaling is a problem of the past; information can be turned on and off; features can be viewed in 3D; and measurements between points of interest can be calculated in 3D space, for example, between vein wireframes and drill hole sample information. A suite of custom scripts has been developed that take the spatially accurate, registered and attributed polyline data from photogrammetry scans and converts them to a geological mapping legend with vein textures, structural information, and lithological boundaries. These 3D maps can be plotted in plan or section view and satisfy the requirements of the most ardent paper map supporter.

Mar 22, 2022

This paper discusses the recently com- pleted TBM-driven pressure tunnel at the Sand Bar Hydroelectric Power Project. The Sand Bar Project is a diversion scheme situated on the middle fork of the Stanislaus River in the Western Sierra Nevada, California, U.S.A. As part of the project, a 5.6 km long and 3.71 m diameter unlined pressure tunnel was bored by a Jarva TBM at the average rate of .37.5 m/ day. This report deals with construction aspects of the tunnel, including TBM performance, lining design, and remedial support measures. Correlations between TBM performance, geologic conditions, and rock properities are made, and the Contractor's mode of operations are discussed. Advance rate prediction, and the impact of these excellent advance rates attainable in hard rock using the new machines are discussed.

Jan 1, 1987

By M Fitzgerald

Fimiston Open Pit is operated by Kalgoorlie Consolidated Gold Mines (KCGM) as a joint venture between Barrick Gold and Newmont Mining. Over 110 years of underground mining resulted in the development of nearly 3500 km of underground workings including backfilled and open stopes up to half a million tonnes in size. These voids significantly complicate blasting processes at KCGM, influencing blast movement direction and magnitude. Blast movement monitoring to improve mine reconciliations was identified as an improvement project in the business plan for the geology team in 2008. Following successful trials in 2008 to 2009, blast monitoring and translation of ore blocks were implemented as a permanent grade control program from late 2009 and is now part of the Management Operating System (MOS) of the mine. This paper presents a summary of results from the Blast Movement Monitoring (BMM®) data collected to date. Ore blocks at KCGM are translated primarily using BMM® data. This data is obtained from the BMM® system which measures the movement of a radio transmitter installed in a blast pattern from a preblast position to a post-blast position. The application of the data collected by the BMM® tends to be both mine site and blast specific. At KCGM, an average distance obtained from the BMM® data within a given shot is the primary method used for translation. In the case that BMM® data is unavailable, a theoretical movement vector established from Orica Shotplus with distances gained from the historical BMM® database is used. Data is presented in an ore loss and dilution exercise for a bench undertaken at KCGM to understand the potential effects on reconciliations. Improvements that have flowed from implementing blast monitoring include improved reconciliations when combined with other grade control improvement projects. The increase in liaison between the geology and blast personnel at KCGM has been a significant improvement gained from the implementation of the blast monitoring program. This has allowed a better understanding of blast movement and the effects on ore dilution and ore loss by the mine geology team. In addition, the discussion of blasting tie-in plans between geology and blasting personnel has been improved which leads to more favourable blasting practices that take ore movement into account.

Aug 22, 2011

By T Arena

To maintain copper recoveries and maximise production at the Sepon Copper Operation it is crucial to control the amount of copper entering the leaching circuit. This requires close control of blending of the multiple ROM stockpiles to achieve the desired head grade. Grade variability in the ROM stockpiles can lead to significant variation in the processing plant copper feed grade.Head grade sampling from the milling circuit at Sepon is complicated due to milling in leach solution to preserve the water balance. Copper is present in both liquid and solid forms and copper in the added milling solution has to be accounted for. This leads to difficulties in manual head sampling which also introduces delays due to sample preparation and assay turnaround. On-stream analysis is complex because of the solution and solid copper and the need to account for recycled copper solution.This paper describes the complexity of feed grade management at Sepon and the application of on-belt analyser technology to assist in the control of copper metal throughput.

Aug 8, 2011