Search Documents

By Rodrigo Ribeiro de Andrade, Túlio César Nogueira, Ed Juarez Mendes Taiss, Nilton José Lucinda de Oliveira

The objective of this study was to determine the effects of an eventual slab central macro-segregation in microalloyed steels with low Mn content (0.80%) and high Nb content (0.08 to 0.10%) on the kinetics of recrystallization of austenite during its rolling, on its critical temperatures, that is, of non-recrystallization (Tnr), start Ar3 and finish Ar1 of ferrite transformation and its response to a simulated industrial thermomechanical processing. The determination of the austenite recrystallization kinetics was made through isothermal double compression tests using a dilatometer, while the critical temperatures were determined through hot torsion tests in a Gleeble® 3800. It was found that austenite recrystallization kinetics, Ar3 and Ar1 temperatures did not present significant changes for the samples extracted both at ¼ of the thickness and at the core of the plate, indicating that, as expected, the central segregation in this type of steel was not intense to the point of affecting this phenomenon. The Tnr values determined for the samples extracted in the core of the plate were, on average, 30°C lower than those obtained from specimens extracted at ¼ thickness, which suggests that a significant portion of the carbonitrides present in the core of the slab are eutectic and coarse, not having completely dissolved during the reheating of the specimens. This occurred despite the fact that the austenitization temperature adopted in this treatment theoretically leads to the total dissolution of Nb, as seems to have occurred in the case of specimens extracted at ¼ of thickness, where carbonitrides have a finer size.

Oct 1, 2019

By Arnaldo Forgas Júnior

Three techniques for ferrite quantification were applied in a duplex stainless steel UNS S31803 solution treated at three different temperatures, 1000, 1100 and 1200°C, in order to verify their compliance with the results from ThermoCalc® prediction. It is verified that only austenite and ferrite phases are present in the samples and that an increasing in solution treatment temperature led to the increase of the volume fraction of ferrite. It is also observed that quantitative stereology technique shows absolute values closer to ThermoCalc® predictions. On the other hand, measurements by ferritoscope and XRD show significant deviations, probably due to texturing effect imposed by the rolling process.

Aug 16, 2017

By Boryong Lee, Heedong Sung, Minho Park, Sunyoung Choi

Recently, the demand for ultra-thin steel plate with high hardness and strength has been increasing in various industries. In order to satisfy this requirement, steel company designs the chemistry with low CEQ and obtains the required characteristics through quenching and tempering process. Especially, these steels are accompanied by low temperature tempering as a necessary process. Unlike ordinary high temperature tempering steels, it is impossible to improve the flatness after low temperature tempering. Therefore, shape control in the quenching process is very important for securing the excellent quality flatness. In order to obtain flatness in the quenching process, uniform cooling inside the plate should be accompanied. However, the quenching process has limitations in estimating the temperature behavior during cooling because the plate temperature is lowered to room temperature. In this study, a thermocouple was installed inside the actual quenching plate to measure the temperature behavior during cooling and to establish the manufacturing conditions of the quenching plate to ensure excellent flatness quality.

Oct 1, 2019

By Wolfgang Linden

One of the most important factors in successful electric steelmaking is the continuous observation of the process and the reaction to it. Traditional electric arc furnace control uses mainly direct controls which are based on the electric power input. Not considering the furnace conditions will necessarily lead to suboptimal operation in terms of energy consumption and productivity not fully utilized.The ARCCESS FEOS (Furnace Energy Optimization System) includes the simultaneous control of the transformer tap, impedance operating point, reactor tap, burner and carbon injection, and DRI charging control. FEOS has proven in practical operation benefits of high melting yields, no interruptions through switch offs in borderline temperature area, rapid reaction, reproducible and efficient electrical energy input and short power-on times.

Jul 30, 2018

By G. Martino, F. Silva, Emmanuel Marchal

The definition of the chemical specification at multiple steps of the steelmaking process is very common in the industry. Among all elements and compounds, the Sulphur content has a special control over several stages, from the coal blend to the final products. Coke, iron and steelmaking specialists usually agree on a static specification for each intermediate product according to their local operation capacity and production cost. However, local decisions have major impacts on the whole production chain and many global factors should be considered in order to make the best decision. In this study, we will exemplify focusing on Sulphur content concepts and techniques that could be applied to many decisions in an integrated carbon steel plant. The variation of coal and coke prices, the desulphurization cost and time, the processes operating points, the hot metal rate at converters, prices and demands of low and ultra-low Sulphur steel grades are some of the integrated factors that are usually disregarded during the specification process. Mathematical modeling presents itself as a proper option into dealing with all the complexity that emerges from integrating all these processes' trade-offs and decisions. This study presents the results of a mathematical model that encompasses economic, thermal, chemical, and mass balances, physical quality of materials and productivity constraints of all processes of a hypothetical integrated carbon steel plant. It optimizes the iron and steelmaking process on a global and unique objective, dynamically defining targets for product quality to achieve the lowest steel production cost. This study details multiple market-plant scenarios in order to compare economic and operating results of a static vs dynamic specification practice.

Oct 1, 2019

By Gigliola Salerno

The carbon-epoxy composite has high specific resistance and strength, which means specific applications. However, its behavior under compressive stress could be decreased by delamination, needing more detailed studies. The main purpose of the present work is to verify the mechanical properties in bending process considering two different fiber orientations. The composite materials were made by woven fibers and epoxy resin. Primarily, the carbon fiber fabrics suffered a superficial physical treatment called silanization, in order to developing a better chemical adhesion between fibers and resin. After the superficial treatment, the layers were embedded with epoxy resin. The composite resin’s cure was made in a Fanem heater, model 320, during 1 hour at 120°C at 1.5 bar; subsequently the specimens were cut by water jet. Specimens oriented in 0°/90° and 0°/90°/45 were manufactured and taken to bending tests, accordingly to the ASTM E855 and D790 standards, in an universal testing machine MTS – Material Test System, full capacity of 250 kN. It was concluded that all specimens failed by tension. Specimens with internal void volumes results in lower flexural modulus and those with presence of fracture mechanisms, like delamination, showed lower strength values. Scanning Electronic Microscopy demonstrated the damages involved during bending process.

Oct 30, 2017

By Peter Grawenhof

Universal joint shafts and slipper spindles are commonly used in rolling mills to compensate the design- and process-related offset between the motors and work rolls. Although both types of shafts exhibit on the same kinematic principle, there are basic differences regarding the design concepts. These differences become noticeable on many levels and may become very distinct in terms of Life-Cycle-Costs (LCC). In this respect, a critical comparison between universal joint shafts and slipper spindles can be made.

Aug 16, 2017

By Guilherme Corrêa Soares

Deeper understanding about the strain hardening behavior of steels has become necessary due to its importance in industrial processes such as mechanical cold forming, rolling and drawing. In this work, the strain hardening behavior of AISI 304, non-grain oriented electrical (NGO) and dual phase steels was investigated. Tensile tests were performed and the strain hardening behavior of each steel was studied by the Hollomon’s equation. X-ray diffraction measurements and hardness tests were also carried out in order to characterize the specimens. Different work hardening stages were observed in each steel during the deformation process. The results obtained are discussed in terms of the relationship among the instantaneous strain hardening coefficient, hardness and eventual phase transformations. The instantaneous strain hardening coefficient of dual phase and NGO increases after the yield point, rapidly reaching its maximum and then steadily decreases until tensile strength is reached. In AISI 304’s case, the strain hardening coefficient keeps raising to high values in response to a large strain and then rapidly decreases before reaching the tensile strength. In comparison to the other steels, AISI 304 shows higher instantaneous strain hardening coefficient value, which persists even in large strains. This is a consequence of its strain hardening mechanism based on stress-induced martensite transformation.

Aug 16, 2017

By Thierno FALL

This paper describes the study of the work-roll during the hot rolling process thanks to a 3D model built with the Finite Element Method (FEM). In terms of computational cost, that method needs high resources compared to 1D model which are mostly used. However, the 3D model is built to have a better understanding of the work-roll thermal and mechanical behavior during the hot rolling process. The thermal model shows that the highest temperature reached during rolling are within the range of 500°C and 600°C. The thermal field input used to simulate the mechanical behavior of the work-roll shows a biaxial thermal stress state, in the circumferential and axial planes. However, a peak of radial stress is observed in the backup zone. It did not generate plastic strain but could influence the fatigue behavior of the work-roll.

Oct 1, 2019

By Adriano Gonçalves dos Reis

In the development of the structural materials for the advanced applications, as in the aerospace industry, there is a constant strive to increase both strength and toughness. Maraging steels are iron-nickel alloys designed to combine both properties that are achieved through the age-hardening of low carbon martensite. This alloy have a metastable martensitic structure that can revert to austenite when heated in temperatures close to the aging temperature, and this effect can be enhanced with the temperature increasing and time of treatment. Therefore, the study of creep behavior in elevated temperatures has technological importance to the development of this material. In this work the creep behavior of a maraging 300 steel solution annealed is evaluated by carrying out creep tests at 650ºC and in a stress of 200, 300 and 500 MPa. Creep parameters, such as steady state creep rate (?????), final creep time (tf), and stress exponent from secondary creep (n) are determined, considering that they are important to evaluate the creep resistance of the material.

Aug 7, 2018

By Douglas Glenn Stalheim

The uniformity of the final cross sectional microstructure and subsequent final mechanical properties and shape of structural steels is dependent on the type or types of recrystallization behaviors that are created. There are three main recrystallization behaviors that are the foundation of the metallurgy created during production. Alloy design and subsequent processing design strategy drive how much of each recrystallization behavior is created through the cross section of the product. Carbon manganese steels create only one basic behavior while the addition of microalloys, in particular niobium, can add two additional behaviors. The behaviors are intertwined with each other and build upon each other. The three behaviors are Type I, static recrystallization, Type II, no-recrystallization, and Type III, metadynamic/dynamic recrystallization. How much of each behavior is generated through the cross section through the production influences the final transformed microstructure and corresponding mechanical properties and shape performance. This paper will discuss the three behaviors, how they are generated, how to identify which behavior is occurring through modeling or actual mill data. Actual examples from production will be discussed.

Aug 16, 2017

By Osvaldo Guilherme Comineli

An extensive investigation into the role of low copper contents on the hot ductility of C-Mn-Al steels has been carried out in order to better understanding the problem of “hot shortness”. Previous work has suggested that this problem results from the build up of Cu that occurs at the surface of the steel as a consequence of the preferential oxidation of iron. This causes the formation of a Cu-rich film of low melting point. A nickel addition has been reported as a solution to the problem, since it increases the solubility of copper in the austenite. After hot tensile testing to failure, samples of Cu-containing steels have been examined using optical, scanning and transmission electron microscopes. Recently published results indicate that copper, in addition to precipitating out as CuS, also segregates to MnS inclusions forming a shell around them. This does not seem to impair the hot ductility under an inert atmosphere, but may have serious consequences under an oxidising environment and lead to “hot shortness”. The influence of nickel in improving the hot ductility seems to be due to it forming a higher melting point alloy with the segregated copper. Data from this incomplete work also suggests that Ni reduces the precipitation of CuS particles. Current investigation carried out using confocal microscopy still to be completed will improve the understanding of the role of copper and nickel on the problem of “hot shortness”.

Aug 8, 2018

By Henrique Silva Furtado

Light meter is an ArcelorMittal innovation that uses off-gas light intensity to predict bath carbon, which is akin to the visual cues that the operators employ to finish a blow. Light meter enables the prediction of end point that is independent of any operator’s judgment. The results have been in general consistent with the actual carbon content at BOF end point at Tubarão. Besides some outliers that occurred due to strange intensity curves, the system implemented in Tubarão BOF 3 reported a carbon prediction error statistic that is very similar to dissolved oxygen–carbon end point statistics. Preliminary trials using light meter without any filter improved carbon hit ratio significantly.

Jul 30, 2018

By Edmar de Souza Silva, Antonio Augusto Gorni, Emanuelle Garcia Reis, Daniel Bojikian Matsubara

Controlled rolling followed by accelerated cooling, known worldwide as TMCP, aims to increase mechanical properties without toughness deterioration. The process principle is to promote the plate cooling with water jets along the range of the austenite transformation temperatures. The accelerated cooling process is only fully effective when controlled in an integrated manner, as it alone cannot ensure significant improvements in the final properties of steels. Plate surface quality depends on some parameters that must be controlled before the start of the plate accelerated cooling. Good flatness is essential to avoid irregular water accumulations during cooling. After the reheating process, the slab should have uniform temperature, uniform austenitic grain size and easily removable scale. The slab thermal and microstructural heterogeneities are inherited by the rolled plate and tend to increase further during the accelerated cooling. This results in flatness problems, high level of internal stresses and mechanical property variations. The descaling strategy is an extremely important factor and must be determined with great caution. It is important that scale thickness and distribution is uniform to ensure homogeneous cooling over the entire plate surface. Otherwise, there will be an uneven temperature distribution, which can cause serious problems of flatness, surface quality and mechanical properties.

Oct 1, 2019

By Ivan César Lopes Diniz, César Romero Afonso Goulart Júnior

Mandrels are tools applied to manufacturing seamless tubes. In VSB plants (Vallourec Soluções Tubulares do Brasil), it is used in two mills. Mandrel and PQF Mills. This is an expensive tool due its alloy (hot work tool steel – AISI H13) and lengh (between 12 meters and 22,5 meters). An opportunity to apply mandrels from PQF in Mandrel Mill has been identified. However, mechanical properties of PQF mandrels must be improved. This work presents the heat treatment process of Quenching and Tempering developed internally at VSB to improve PQF mandrel properties aiming to achieve Mandrel Mill requirements. Hardness and metallography tests were performed before and after some steps of the heat treatment to characterize and validate the process.

Oct 5, 2019

By Vinícius da Silva Madruga

Os processos de lingotamento contínuo e de lingotamento convencional apresentam diferenças na solidificação dos aços, esse fato tem impacto na distribuição, quantidade e forma de inclusões de óxidos e sulfetos. O objetivo desse trabalho é verificar de que maneira tais diferenças influenciam na distribuição dos sulfetos ao longo do aço solidificado de qualidade SAE 1050. Para isso, 20 amostras foram retiradas de eixos forjados e barras laminadas, produtos conformados de origem do lingotamento convencional e do lingotamento contínuo, respectivamente. As amostras foram analisadas em microscópio ótico e microscópio eletrônico de varredura no modo de análise automatizada de partículas. Através das imagens e de dados numéricos obtidos, foi visto que nas amostras de barra laminada há grande quantidade de sulfetos, se analisada na seção longitudinal, em relação às amostras de eixo forjado. Analisando na seção transversal, foram detectados menos sulfetos devido ao alinhamento dos mesmos. Entre as amostras de eixo forjado, a área ocupada pelos sulfetos é maior no pé do lingote, reduzindo em direção à cabeça, apesar de a cabeça apresentar mais sulfetos. Tais diferenças foram atribuídas à taxa de resfriamento, à seção transversal do produto e ao processo, que variam entre os dois tipos de lingotamento.

Oct 30, 2017

By Fernando Ruiz Díaz

En aplicaciones a elevadas temperaturas como por ejemplo en cámaras de combustión y toberas de vehículos aeroespaciales se requiere el uso de aleaciones que permitan una elevada extracción de calor y buenas propiedades mecánicas. En este trabajo se realiza un análisis comparativo de las aleaciones Cu-Cr-Zr y Cu-Ag-Zr. Las mismas fueron sometidas a ensayos de resistividad eléctrica entre 25ºC y 700ºC y de tracción a 150ºC, 450ºC y 700ºC. Los resultados de los ensayos de resistividad eléctrica fueron convertidos a conductividad térmica mediante la relación de Wiedemann- Franz. A través de este análisis se observa que la aleación con mejor conductividad térmica es la de Cu-Ag-Zr presentando además un cambio de fase que no es observado en la aleación Cu-Cr-Zr. Respecto al ensayo de tracción la aleación Cu-Cr-Zr presenta mayores valores de resistencia a la tracción y tensión de fluencia a las temperaturas estudiadas.

Aug 16, 2017

By Wan-sub Kim, Joon-Tae Lee, Seongkyu See, Yong-Kyu Park

Softening heat treatment of CHQ alloy steel (Cr-Mo Steel) is a bottleneck process that requires 90% or more of the entire manufacturing process. In order to reduce the property deviation between edge and center and remove the low-temperature structure problems, CHQ products is heat treated by customers. This technology comes from the idea to solve the problem by applying the concept of “In-line isothermal transformation through initial quenching + heat source addition. Consider the stability of field operations, durability from high ambient temperature and fall of scale, Instantaneous heating and cooling control was required for the conversion of slow cooling and rapid cooling products. An electric heating system was applied to the underside of Stelmor air-cooling nozzle. Using the Scan Pyrometer, the feedback control was performed and fine temperature control was performed through the thermocouple by zone. Through the this technology, it is possible to develop and expand products that can be shortened or omitted by the heat treatment process of customers.

Oct 1, 2019

By Aperam South America

Balanço Energético Global e Utilidades - 2013

Jul 31, 2018

By Jorge Madias

Durante la laminación de barras y alambrones para construcción civil; perfiles y ángulos estructurales y barras redondas y hexagonales de aceros de corte libre puede presentarse la apertura de la punta o la cola y el estallido central, con la consiguiente parada y caída de la productividad, y pérdida de rendimiento metálico. En este trabajo se analizan las diversas causas que confluyen para que este problema ocurra. Se analiza la influencia de posibles defectos en las palanquillas, las características del corte de las mismas y otros problemas de calidad. Se revisa el rol del precalentamiento previo a la laminación, la refrigeración de los cilindros, el diseño de pasadas y la respuesta del material en función de su ductilidad. Se presentan diversos casos industriales para ilustrar las diferentes razones detrás del problema de la apertura de punta.

Jul 30, 2018