Search Documents

The influence of varying amounts of magnesia, silica, and alumina in iron ore sinter on its mineralogy, reducibility index (RI), reduction disintegration index (RDI), physical breakdown (AI and TI), and production properties (coke breeze rate) were examined. It was found that the mineralogy of iron sinter can more easily be predicted from its chemical composition than from the RI, RDI, AI or TI. Anticipating the consequence that varying amounts of MgO and SiO2would have on sinter properties is complex, and not necessarily predictable. High concentrations of Al2O3in the sinter result in high concentrations of the SFCA phase, but with drastically deteriorated properties. This study also confirmed that the form in which fluxes are added to the raw material sinter mixture affects the mineralogy and properties of the produced sinter.

Jan 1, 2010

By Timothy C. Siegel

Given that piles are composed of different materials and installed using a variety of methods, ASTM D 1143/D 1143M-07 Standard Test Methods for Deep Foundations Under Static Axial Compression is justifiably general so that it has as many applications as reasonably possible. There are aspects of the test setup, the test procedures, and data interpretation for instrumented piles (some of which are specific to augered cast-in-place piles) that are either not discussed in detail in this ASTM standard or are not addressed at all. Specifically, the use of variable time hold times can obscure the shape of the conventional load-deflection curve, as well as, influence the interpretation of the ultimate pile capacity. Unload-reload cycles induce additional non-uniform internal axial loads within the pile which complicate interpretation of the strain gage data and increase the potential for errors. Attempts to maintain a constant top load during the hold period can lead to operational difficulties in taking measurements and are technically unnecessary. Residual load has been shown to develop in cast-in-place piles and can significantly influence the axial load distribution as interpreted from strain gage data. The stiffness of cast-in-place piles has been observed to vary with the measured strain, and a constant modulus, as provided by correlation with the unconfined compressive strength of the grout, may lead to a significantly different interpretation of the axial load distribution.

Jan 1, 2010

By P. C. Carrasco

Knowing the origin of the relevant and irrelevant components of the nugget effect is essential to optimize the process under study. This paper describes the causes of the nugget effect and, its dependency on the sample support, sampling density, and on the QA/QC procedures. Several examples of natural and ?human? nugget effect are given. A method to estimate the magnitude of the relevant and irrelevant components is suggested. Finally, the economic consequences of misunderstanding the nugget effect are analysed.

Jan 1, 2010

By Qingsheng Liu

A new method of recycling aluminum dross for preparation Al-Si-Ti alloy was studied in this paper. This was carried out in two processes. first the aluminum doss was pretreated by leaching and calcining process, the fine purity and phase of the intermediate oxide powder up to electrolysis demands, then, could be obtained when aluminum dross after washing have been leached for 2h at 100? in 20% hydrochloric acid and calcined for 2h at 1200?, which was treated by cryoite-based molten salt electrolysis. Finally, the Al-Si-Ti alloy was successfully obtained through electrochemical co-deposition in the cathode shows a typical as-cast microstructure. This new recycling method can produce high quality alloy and may bring remarkable economic and social benefits.

Jan 1, 2010

By H. Rosen

The pump is the heart of most industrial and mining plants, providing the energy to separate valuable minerals from process feed. The actual effect of the pump, both in terms of production costs and overall process efficiency, is often assumed or misunderstood by engineers due to insufficient pump performance data. Pump performance can be understood and corrected, where required, through continuous performance monitoring, leading to dramatic improvements in both pump life cycle costs and system efficiencies. The performance of every pumping application is subject to variation and the main contributing factors are as follows: ?Unavoidable deviations from pump supplier curves ?Pump wear ?Pump curve derating factors for slurry pumping ?System curve variation ?Deviation from basic principles of centrifugal pump operation. These are discussed in detail through case studies and the author?s personal experiences. This paper shows ways to minimize the effect of these variations, thereby reducing performance loss and preventing damage to the pump. The paper discusses the benefits of efficient pump operation, the requirements of pump performance monitoring, and its practical application to pump operation in the slurry and water environments. The cost of remedial actions is explored and compared against the savings in both power and plant reliability, resulting in a reduced life cycle cost of the pump.

Jan 1, 2010

By J. Pei

The studies of dynamic measurements using stress wave theory has commenced in China. This paper introduces some practical experiences using "CASE method" in Shanghai showing applications of dynamic measurement to determine ultimate bearing capacity of pile, the change of capacity due to set up, determining the optimum bearing layer during pile driving, the efficiency of hammer system and integrity of pile and discussions of method concered.

Jan 1, 2010

By J. O. Osterberg

The realities of foundation enginering are that the work never proceeds exactly as expected. The various reasons, exploration, design, construction, and legal are discussed. Case histories are presented with an analysis of why the projects did not turn out as expected and how the difficulties might have been avoided.

Jan 1, 2010

By Y. K. Wong

This paper describes in detail various problems concerning the construction of a pile-raft foundation supporting a 42-storey tower block. The subsurface generally consists of highly weathered sedimentary rock. A comprehensive instrumentation program is implemented to monitor the behaviour of the foundation system throughout the construction period of the superstructure. Instrumentation observations are highlighted in the second half of the paper.

Jan 1, 2010

By S. M. Spottiswoode

Much as one hopes to predict whether damaging seismicity might occur somewhere in the next shift, this is not possible at present. Recently, an analysis of seismicity at two mines has shown that a small increase in seismicity occasionally occurs before both large and small events. This analysis is extended here to five mines, with the same results. Earthquake seismologists forecast hazard in terms of the average incidence of earthquakes over the last 50 years, adjusted on an hourly basis according to the possibility of aftershocks of events that have happened. The rate of seismicity in any area remains approximately constant when expressed as seismicity per area mined, or better still, per unit of elastic strain energy released. It is suggested that seismic hazard in mines be estimated using historical seismicity and forward modelling, adjusted according to the possibility of aftershocks. In summary, medium-term forecasting of seismicity is viable; short-term prediction of large events is not.

Jan 1, 2010

By F. Z. Suo

Baoahan Iron and Steel Complex is situated at lower beaches of the Yangtze River. The subsoils 50~70 M below the surface is a deposite of Yangtze River delta, consisting mainly of weak silty clay and loam, with low soil bearing capacity. Consequently, to build on such a weak soil a grant iron and steel integrated works weak soil improvement at the Complex, pile foundation is the effective type. It is estimated that at the first stage of Baoshan project 60,000 piles have been driven, of which 60% are steel pipe piles and 40% reinforced concrete piles. To provide reliable basis for pile foundation design, on-site loading tests were carried out for long reinforced concrete piles 27,45 60 M in length ,with strain gauges on the chief reinforcement of pile shaft and strain rod on pile tip. Based on loading tests, the paper discusses and analyses some issues, including determination of load transfer mechanism distribution of frictional resistance. Tests show that as far as long friction piles in soft clay are concerned, regardless of the properties of pile tip's bearing stratum, loads are mainly carried by shaft frictional resistance which it is effective to determine pile capacity in terms of P ~ S relationship.

Jan 1, 2010

By Donald Leroux, Jean-François Wilhelmy, Ahmed Bouajila

"A young private R & D organization, COREM celebrated its 10th anniversary in 2009. Managed by a consortium of nine mining and metallurgical companies, COREM has the mandate of increasing the competitiveness of its member companies through the development and transfer of mineral processing innovations. Typical technologies developed by COREM include alternative mineral processing techniques, novel operating strategies, innovative sensors and process simulation software. Many of them were developed in partnership with universities and selected research organizations.Because the COREM membership base is broad (from ferrous to base, to precious metal industries), its R & D program must deliver technologies with applications within a wide spectrum of mineral processes. Comminution, physical (gravity and magnetic) separation, flotation, cyanidation, pelletizing and thermal processes are the main topics of the R & D program. A number of new technologies have been developed and transferred to the plants of member companies. These examples of transferable technologies demonstrate the capability of COREM to impact the bottom-line of its member companies.INTRODUCTIONCOREM is a private mineral-processing R & D organization that operates from its own laboratories and pilot-plant with its own staff of professionals and technicians (about 95 persons). It is managed and financially supported by a consortium of nine mining and metallurgical companies and three provincial and federal ministries. The very ‘down-to-earth’ mission statement of COREM is to increase the competitiveness of the mineral processing plants of its members. The eighteen plants upon which the COREM technology development program is currently based can be found in Québec, Newfoundland and Labrador, New Brunswick, the Netherlands and Botswana."

Jan 1, 2010

By E. Mongilardi

The construction of large underground openings through cohesionless or weak cohesive soils and under the water table in particular, often requires a ground improvement to be done from the surface or ahead of the excavation face in tunnelling problems. To this purpose various injection procedures have been used in the past and new outstanding techniques have been developed recently, such as "jet-grouting", extending the feasibility range. The paper presents a review of basic principles and practical design criteria with particular reference to the newest trends of development. Case histories have been selected within the experience of specialist contractor Rodio Co. showing the variety of problems solved by manifold grouting procedures and layouts, in widely different soils ranging from the sandy-gravelly alluvia of Milan to the soft marine clays of Singapore.

Jan 1, 2010

By Heather N. Dougherty

In the absence of values for each influencing parameter and a known relationship of input-output space, novel approaches should be implemented as proxy solutions to mathematically complicated problems. Proxy solutions can be in the form of linear or non-linear multiple regression equations. Predicting the performance of gob gas ventholes is one of these mathematically complicated problems as it is difficult to know the exact relationships between various parameters influencing gob gas venthole (GGV) performance from active and sealed (completed) longwall panels. In this paper, a discussion of the NIOSH-developed software suite for methane control and prediction (MCP) based on an artificial neural network (ANN) is presented. The application of the ANN-based software suite to develop algebraic relationships for gob gas venthole performance prediction in sealed and active longwall panels is sought. Output information obtained from the NIOSH-MCP software as a response to various input parameters were used to create an input-output database for total flow and methane percentage from GGVs operating in active mines during completed and sealed panel situations. Due to the multi-variable nature of the software, outputs generated using the software for various inputs were used to develop analytical equations first using linear and then second using non-linear multivariable regression techniques. The advantage of this method is its ability to better understand the significant parameters of the relationships between the inputs and outputs for gob gas venthole production in active and sealed panels and to be able to predict their performances using relatively simple analytical functions.

Jan 1, 2010

By Rameshwar Sreenivasan

This paper presents a sustainability analysis of Selective Laser Sintering (SLS) from an energy standpoint. Data of electrical power consumed by the system over an entire build were acquired using a LabVIEW 8.6 circuit. The power drawn by individual subsystems was also measured, and an energy balance was performed. These data were then used to arrive at a Total Energy Indicator of the process with the help of a specific type of Environmental and Resource Management Data (ERMD) known as Eco- Indicators, which indicates the level of sustainability of the process.

Jan 1, 2010

By A. M. Neale

Kriel Colliery has experienced some sub-standard blast results on the overburden. Blast results are considered poor when the fragmentation is too big, back break into the new highwall, capping is experienced and/or excess overburden material is thrown into the void. Poor blasting leads to lower productivity, equipment breakdowns, and poor drilling and blasting results on the adjacent blast, contamination of coal or loss of coal. A simulation was developed in Microsoft Excel to model blasting results while changing various parameters. From the simulation results, it could be seen that a change of blast design could be beneficial. As an example, smaller drilling patterns were simulated (10 m x10 m to 8 m x8 m, and 8 m x8 m to 7 m x7 m in Pit 5 and Pit 6 respectively) in combination with changes in explosives (P700 emulsion vs. ANFO) and drill bit diameter (311 mm vs. 251 mm). The results show that each of the options has a specific scenario that will be most beneficial to the mine. These results are quite specific and subject to variable inputs. The purpose of the example is to demonstrate how the simulation can be used as a tool to asses blast design variations.

Jan 1, 2010

By Braden T. Lusk, Shannon P. Lusk, Kyle A. Perry

A high explosives shock tube has been constructed and developed to test blast resistant windows with pressure versus time waveforms similar to waveforms generated by arena testing. Calibration of the high explosives shock tube, or Large Arena Test Simulator (LATS), included numerous tests performed by detonating varying charge weights at different distances from three piezoelectric pressure sensors located at one end of the shock tube (where the test subject would be installed). The maximum reflected pressure and positive phase impulse were calculated for each waveform generated in the tests. Pressure versus distance and impulse versus distance graphs were generated. Results have been graphed in order to predict charge weights and distances that correlate to the desired pressure and impulse at the end of the tube for future tests. This is a valuable tool when testing expensive, job specific components so the loading requirements are met on the first attempt.

Jan 1, 2010

By B. B. Broms

The high transverse tensile stresses that develop in precast concrete piles during driving have been investigated experimentally from pile load tests and theoretically using the finite element method (FEM). These tensile stresses can be high enough to cause longitudinal splitting of the piles just below the pile cap. Test data and FEM indicated that the maximum transverse tensile stress will increase with increasing thickness of the cover. The maximum tensile stress can be high especially if the pile is eccentrically loaded. The results from the experimental investigation and from FEM are described in the paper as well as a simplified method based on the stress distribution in a concrete cylinder at an indirect tension test.

Jan 1, 2010

By R. G. Shen

The relation curve of strain and acceleration is presented in this paper. The steel pipe pile of 609.6 mm in external diameter driven by IDH-45 diesel motor hammer on the esturial shoal of Yangtze River. The ultimate bearing capacity of pile is analyzed by one dimensional wave equation and the effect of computational parameters of the equation is discussed.

Jan 1, 2010

By Ruilin Yang

Blast vibration in the highwall from a cast blast in open pit mines or in the hanging walls from a stope blast in underground mines is a common concern. Vibration in such cases is a typical near-field situation where the distance from a blasthole to a point of interest varies significantly compared to the distance between the blast as a whole and the point of interest. Most existing blast vibration models are designed for far-field vibration using a single seed wave to represent all blastholes within a blast and do not simulate wave shape change over the distance. Using the site parameters from the analysis of signature hole vibrations, the present blast vibration model yields reasonable agreement with field measurements in terms of vibration amplitude and frequency. Case studies show that the model has been used successfully to assist field vibration control.

Jan 1, 2010

By G. F. Sowers

Excavation bracing is a special structural system. It is built from the top down. The design is controlled by the economical construction of another structure as well as by the movement of the ground beyond the limits of its construction. It serves a number of purposes, all subordinate to the construction of the principal structure. Despite its importance, bracing design and construction is frequently overlooked in project planning, causing delays and expensive changes. Thoughtful planning, good design and resourceful, innovative construction can improve construction safety and save time and money.

Jan 1, 2010