Search Documents

By Richard H. De Voto

The McDonald gold project and two satellite gold deposits near Lincoln, MT were discovered in the early 1990s. They contain at least 307.9 t (9.9 million oz) of gold and 933 t (30 million oz)of silver. The McDonald gold deposit alone contains 223.9 t (7.2 million oz) of gold reserves that can be open-pit mined and processed by cyanide heap leaching at a projected cash operating cost of $6.10/g ($190/oz). The deposit is predominantly oxidized with no chance of acid production. It can be mined, operated and reclaimed with minimal permanent environmental disturbance other than the creation of an open-pit filled with a fresh-water lake that would support trout.

Jan 1, 2000

Discussion, at the Virginia Beach Meeting, February, 1894, of the Paper of Prof. Posepny. (Trans., xxiii., 197, 587.) Including communications subsequently received. a T. A. Rickard, Denver, Colorado (communication to the Secretary) : The paper of Professor Posepny was printed so short a time

Jan 1, 1895

By Francis J. Fratttali, Verda McLendon, Stanley J. Green

"INTRODUCTION During the first phases of the war emergency the shortage of aluminum prompoted the Bureau of Mines to investigate methods for using low-grade bauxites of high silica content and also clays as raw-material sources of this strategic metal. The Bayer process treats low-silica bauxites to provide the industry with a major portion of the purified alumina, which contains very low percentages of silica and other impurities. One of the methods investigated in the laboratories of the Bureau of Mines for low-grade materials is the lime-soda sinter process, which was studied on a pilot-plant scale. In this process, the alumina content of the alumina-bearing minerals Bs made water-soluble by sintering the raw material with limestone and soda. Simultaneously, the siliceous material is rendered insoluble. The sinter is extracted with an alkaline liquor, and the resulting extract liquor is treated as follows to recover the alumina: (1) Autoclaving with lime to remove silica as a zeolitic complex and (2) treatment with CO2 to precipitate alumina as the trihydrate (A1203.3H20). Figure 1 is schematic flow sheet of this process.As the process is cyclic, it is necessary that nearly all of the soda and alumina remaining in the plant liquors after carbonation be recovered. Upon passing through one cycle, these liquors contain 14 to 15 percent NaCO3 2 to 5 percent NaOH, 1 to 3 percent A1203, minor amounts of silica, and, with certain materials such as Pennsylvania diasporic clays, 0.5 to 1.0 percent Na2S04. Approximately 50 percent of the Na20 in these liquors must be returned, as soda ash, to the dry-grinding and raw-materials blending operations. Previous work (6)5/ on sulfate-free solutions demonstrated that two methods for recovering Na20 were feasible, namely: (1) Salting out Na2C03.H20 by evaporation of the carbonated solutions and (2) crystallizing Na2C03.10H20 by cooling the concentrated carbonated solutions."

Sep 1, 1947

By N. A. C. Smith, D. D. Stark

"Sulphur is apparently a normal Constituent of crude petroleum, but in most crudes is present in percentages of less than one-half of one per cent. Some crudes, however, contain more, and occurrences have been reported of heavy asphaltic oils with as much as five per cent of sulphur.Occurrences of Sulpher-bearing CrudesIn North America, the fields rest of the Mississippi River are almost entirely free from sulphur oils, the time oil from Northern Ohio and Indiana, and the Potrolia crude in Ontario, being practically the only ones which contain sulohur in amounts over 0.5. per cent. In the Mid-Continent district the production of high sulphur crude in general is small and unim¬portant. The two main excentions are the Healdton field in Oklahoma and the El Dorado field in Arkansas, both of which produce oils with considerable sulphur content. In the Wyoming field, one sand, the Ember Sandstone, pro¬duces a crude of high sulphur content, and it is probable that this crude rill be of considerable importance as production increases. At present, however, very little crude is produced from this formation. In the Gulf Coast conditions are irregular, some crudes being low in sulphur and others comparatively high. The same is largely true of California. The crudes of Mexico contain notable amounts of sulphur, and as they have been of great commercial importance in this country, a typical sample of light Mexican crude was selected for the present study. It is probable that the results obtained poly also (but to a lesser degree) to other sulphur-bearing oils. An analysis of this crude will be found in Table 3, also analyses of other typical sulphur-bearing crudes from different sections of the United States."

Mar 1, 1924

By Lisa M. Splitter

Drilled displacement piles were constructed as the foundation for a proposed 10-story building in San Francisco, California. At the study location, the stratigraphy consists of 14 to 21 feet of fill and 13 to 23 feet of weak, compressible clay (?Bay Mud?), underlain by dense sand, stiff clay, and bedrock. A sensitive critical public utility is located within approximately 20 feet of the constructed piles along one side of the building. The utility pipeline is entirely within the Bay Mud where it is adjacent to the project site. The San Francisco Public Utilities Commission (SFPUC) developed limits on the allowable total and differential movement of the utility pipeline. As requested by the SFPUC, inclinometers and piezometers were installed to monitor the soil movement and pore pressure increases in the Bay Mud caused by the installation of drilled displacement piles. Action levels were set such that if displacement and/or pore pressures reached an action level, the installation methodology would be reevaluated and additional measures to reduce these effects would be implemented. This paper will present the sequence of pile installation near the pipeline and monitoring points, and the data collected from inclinometers and piezometers at variable depths and distances from the piles. The data will highlight the build-up and dissipation of pore pressures over time and the displacement of Bay Mud caused by the pile installation. The conclusions of the study are useful in determining sequencing, spacing, predrilling, and other measures that can be implemented to decrease the displacement potential and pore pressure build-up in soft clays.

Jan 1, 2009

By M Fahey

Large volumes of tailings are produced annually by the goldmining industry of Western Australia. This material ishydraulically discharged into large storage facilities usingsub-aerial deposition methods. Much of the gold comes fromhighly weathered rock, resulting in tailings with significant claycontents. Consolidation of these materials can be very slow,particularly if occurring under the effects of self-weight alone.To optimise the consolidation behaviour of the tailings, disposalstrategies can take advantage of the effects of evaporation byallowing each tailings layer to dry before the next layer isdeposited. In the last 20 years, much of the gold processing inWestern Australia has utilised saline groundwater. As the salinetailings dry, the surface will develop a thin salt crust. Laboratorytests have shown that these crusts can drastically reduce thesurface evaporation, adversely affecting the behaviour of thestorage. This problem has been the focus of an extensive researchprogramme, with the objective of obtaining a fullerunderstanding of the mechanisms controlling the coupledconsolidation and evaporation behaviour of saline gold tailings.Part of this study involved site investigations of a wide range ofstorages to ascertain their current states. Methods of gainingaccess to the tailings following deposition were developed.In situ testing and high quality sampling were conducted on each storage and samples returned to the laboratory for analysis. These investigations have enabled full characterisation of the storages to be accomplished. Examples of data are shown herein and the implications of the results are discussed.

Jan 1, 2001

By Ed D. Thimons, Douglas E. Pollock, Andrew B. Cecala, Gregory J. Chekan, Jay F. Colinet, John A. Organiscak

Researchers at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) work to reduce respirable dust exposures in mining operations. One focus of this research is silica dust control for surface and underground operations in the metal/nonmetal mining industry. PRL researchers analyze dust sampling results from the Mine Safety and Health Administration (MSHA) to identify high-risk occupations to guide research efforts. Research is then conducted in an effort to improve existing technologies and/or develop new controls for reducing worker exposure to airborne silica dust. During the last few years, PRL researchers have conducted research related to the following goals: improving protection provided by enclosed cabs on mobile surface mining equipment, reducing dust generation from surface drills, reducing dust levels in iron ore operations, and developing a new method to clean dust from workers’ soiled clothes. A description of each of these controls and subsequent dust reductions quantified through site surveys will be provided.

By Hendrick A. D. Kirsten, A. Clayr Alexander

Stillwater Mining Company is currently developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in the Bear tooth Mountains of southern Montana. Portals for the two access tunnels required at the new site were excavated in limestone talus to accommodate4.6 m (15 feet) diameter tunnel boring machines. A review of the technical design, field conditions and construction of the portals is presented.

Jan 1, 2001

By D. L. Murr, J. R. Jensen

Testing was conducted on a Minnesota Iron Ore concentrate with Cook Clay as a binder using compressive sheer mixing to enhance the performance of the agglomeration mechanism. The testing was conducted on a bench scale at the Midland Research Center the summer of 2004. Results of the test program will be presented that shows the impact of compressive sheer mixing had on the strength achieve in a green ball.

Jan 1, 2006

By Clarence Karr

AN EXTENSIVE characterization was conducted on the neutral oil components in a low-temperature bituminous coal tar. A total of tai individual compounds identified with respect to individual isomers, and at least 55 other compounds were indicated to be present. The amounts were determined in all instances. A comparison of isomeric distribution in the tar with thermo-dynamic equilibrium distribution, and kinetic distributions indicated that the composition of the tar largely reflected the structure of the coal from which it was formed. Detailed descriptions are presented for the separatory and qualitative and quantitative procedures for the characterization of the neutral oil component. These include micro fractional vacuum distillation, displacement liquid chromatography, gas-liquid chromatography, countercurrent distribution, and infrared and ultraviolet spectrophotometry. Descriptions are given for the synthesis of authentic specimens of alkylindenes, The ultraviolet and infrared spectra of 134 polycyclic compounds, ranging from alkylindenes to alkylphenanthrenes, either found in the distillable neutral oil, or thought likely to be present, are also given.

Jan 1, 1967

In the Ngakuru area, zeolite deposits occur in late Quaternary lake sediments and ignimbrites. The deposits are associated with sinters, hydrothermal eruption breccias, and quartz-adularia altered fault breccias: all indicators of a shallow epithermal environment. Several of the deposits are adjacent to epithermal gold prospects. Zeolites are most abundant in lacustrine tuffs of the Ngakuru Formation, a 100-300 m thick sequence of siltstone, tuff, diatomite, sandstone and conglomerate. The formation overlies the Ohakuri Ignimbrite dated at c. 270 Ka, and is unconformably overlain by alluvial sands and gravels which are younger than 20 Ka. Individual zeolite deposits contain 30-80 per cent zeolite over a thickness of up to 45 m in thinly stratified tuff beds. The tuff beds are locally overlain by diatomite. The tuffs are composed mainly of glass shards and pumice clasts, with minor volcanic plagioclase, quartz and biotite crystals. Glass shards in the tuffs are replaced by the silica-rich zeolites mordenite and clinoptilolite. Amorphous silica (opal A), opal-CT, K-feldspar and smectite are also present. The distribution of the Ngakuru Formation is controlled by northeast trending normal faults, which separate it into the Ngakuru and Guthrie grabens. A silicified (quartz-adularia altered) hydrothermal breccia along one of the fault zones suggests that the faults acted as feeders for heated water that caused the deposition of the zeolite minerals. Some of the zeolite deposits are adjacent to sinters and hydrothermal eruption breccias. The location of the sinter about 20 m above one deposit indicates that the zeolites were formed at a depth of 20 to 70 m below the paleosurface. The hydrothermal eruption breccias contain clasts of altered ignimbrite, which contain geochemically anomalous gold and silver values. By analogy with their occurrence in active geothermal systems in the Taupo Volcanic Zone, mordenite and clinoptilolite in the Ngakuru deposits probably formed at temperatures of 60-150oC from near-neutral pH waters as a result of interaction with glass-rich tuff beds. The Ngakuru zeolite deposits are therefore interpreted as shallow hydrothermal alteration zones within larger epithermal gold-bearing systems.

Jan 1, 2002

By Robert A. Siokler

Approximately 75 percentage of the earth's land surface is comprised of shale or shale-like materials. Shale itself is composed of the residue from an almost infinite variety of weathered parent materials which have undergone deformations ranging from intense to negligible. Under standard test procedures, shales exhibit a very wide range of physical properties particularly if the test specimen is subjected to a change in moisture content, when the original test values may vary from 0 to 100 percentage. It is this wide variation in physical property values compounded by its ubiquitous presence that makes shale such a problem material to engineers. In reviewing the literature relating to shale, it is evident that the "problem" has been approached from many directions. In order to understand why shales behave as they do, investigators have sought mineralogical, geological, chemical, electrical, and physical answers. Each study yields valuable academic information, but few contribute much of value to the engineer in the field. Many valid relationships between shale strength or competency and clay type, clay content, organic content, water content, grain size, cementation, density, porosity, etc, have been established. Yet it is very difficult to extend these understandings to the in situ condition with results that can be used by the field engineer. One major reason earlier work has not produced better information lies in the ambiguity of the definition of shale. It is apparent that no one laboratory parameter can be successfully used to provide sufficient engineering information to properly describe in situ conditions. For example; shale with swelling clays will produce low strength values provided: the swelling clay is in sufficient quantity, the clay is dispersed throughout the medium involved, and there is a low value of cementation. Shales with high unconfined compressive strengths have been found with very low shear strengths. Sandy shales often provide as many ground control problems as clay shales. Shales of similar nature may provide good roof conditions in one part of a mine yet in another part of the same mine the apparently identical shale may cause substantial problems. A clear need exists to classify shale in a manner which will enable the engineer to better predict the strength and durability of shale-like materials. Studies at the University of Missouri-Rolla (UMR) have focused on finding parameters which influence durability and competency, while being discretely discernible through uncomplicated testing. Initial research concentrated on distinguishing shale8 on the basis of standard physical tests such as: unconfirmed compression, triaxial shear, and slake durability. As results accumulated, however, it became evident that moisture content played a much greater role in determining competency than had been recognized previously. As a result the focus of the research turned to developing tests which would evaluate the influence of moisture on shale behavior. The above work then became a foundation for a second phase of investigation in which a suite of standardized tests were developed to provide a classification procedure. From this study five tests were identified as being critical: Moisture Activity, Atterberg Limits, Submersion, Unconfined Compression, and Shore Hardness.

Jan 1, 1986

By E. Z. Casassa

There has been a recent revival of interest in concentrated coal/water slurries as a substi¬tute for fuel oil or for coal/oil mixtures, particularly in electric power generation. The idea is not a new one. Coal/water slurries were transported by pipeline in the U.S. in the early nineteen-sixties, and the Black Mesa coal pipeline has been in operation for several years, while in Germany, coal/water slurries were being burnt for power generation in the early nineteen-seventies, as described by Merten and Höner (1972). Since coal is not a pure substance but a carbonaceous mixture, the different chemical and physical behavior of coal/water dispersions from different deposits must be understood in order to optimize the properties of the result¬ing slurry fuels. Since minerals which are minor constituents of coal may also strongly affect slurry properties, coal chemistry may vary considerably even within a single deposit. Thus it is unlikely that there will be a single formula for optimizing the slurry properties of all coals, and even the answer for coal from a single source may change with time.

Jan 1, 1983

By J. R. Koehler

Although two-entry yield pillar-based gate roads supported by wooden cribs have been commonly used throughout longwalling in the Wasatch PlateadRoan Cliffs coalfield of central Utah, a three-entry yield-abutment gate road configuration was recently trialed in the Hiawatha Seam at the Genwal Resources (GRI) Crandall Canyon No. 1 Mine, near Huntington, UT. Pillar, entry, and cable bolt performance were monitored through second panel mining using a fairly extensive array of geomechanical instruments installed over a span of four crosscuts. Ground pressure and entry closure measurements confirmed that the 9.1-m-wide (30-ft) yield pillar was partially shielded from first panel longwall loads by the 36.6-m-wide (120-ft) abutment pillar, and consequently, experienced only minor yielding until the approach of the second panel face. Complete yielding of the 9. I-m-wide (30-ft) pillar occurred when the second panel was approximately 6.1 m (20 ft) inby the instrumentation site. Average cable bolt loads and differential roof sag remained low through second panel mining and tailgate entry ground conditions were excellent; however, very high ground pressures in the abutment and yield pillars, and second panel rib strongly suggest a high potential for coal bumps utilizing this gate road configuration at mining cover depths in excess of 396 to 457 m (1300 to 1500 ft). This conclusion is supported by the suspected occurrence of small coal bumps along the abutment pillar ribs, observed indirectly as fresh debris in the middle entry just behind the second face. This paper presents a case history developed from the geotechnical measurements and on-site observations of this unique application of a yield-abutment gate road configuration and cable support system in the Hiawatha Seam.

Jan 1, 1996

By R Stefansen

Stockyard operations are governed by the interaction between the different disciplines required to successfully schedule and control the supply chain of raw material through the stockyard in combination with the effectivity of the operation of the stockyard equipment. The system demonstrates a proven technology for implementing a centralised operation of full unmanned stockyard equipment, using a high precision absolute positioning system based on a Real-Time Kinematic (RTK) Global Navigation Satellite System (GNSS) receivers in combination with 3D rangefinders. The system implementation maps the surface profile of the stockyard inventory and allows in combination with proprietary algorithms for full operation of the stockyard machines without on-board operators. The operational impact of delayering the process by moving to a centralised operation is examined, together with the combined effect on the overall safety in the stockyard as a result of a change in reliance on operator skill dependencies. Average performance gains range from 10–20 per cent. The performance of the automation system is related to a consistency and reliability of uniform operation, which has an impact on the life expectancy and the effectiveness of the equipment. The effects of having instantaneous and correct information about the stockyard inventory volume measurement are investigated in relation towards spot price trading in current fast reacting markets.CITATION:Stefansen, R, 2017. Advanced automation for centralised stockyard operations, in Proceedings Iron Ore 2017, pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Alfonso Rizo-Patrón

El presente trabajo describe la importancia de la explotación de los fosfatos de Sechura en la cuenca del Pacífico. Para ello, se evalúa el potencial de recursos naturales aprovechables en una infraestructura concentrada del área de Bavoyar y su implicancia en el aprovechamiento del potencial para el año 2000. Asimismo, es importante la planificación de un programa y una coordinación técnica adecuada de las realidades físicas, geográficas y geológicas de la cuenca señalada, así como la responsabilidad que ello implica.

Nov 20, 1972

By James A. Finch, Stéphanie Gélinas

"A colorimetric technique, originally developed for methyl iso butyl carbinol (MIBC) based on the Komarowsky reaction, has been extended to a wide range of common mineral flotation frothers. The procedure, which is briefly described, is shown suited to on-site determination in a series of industrial campaigns. Some frother observations are described, including: concentration evolution down a bank, distribution between pulp and froth phases, and a mass balance around a circuit. Minute amounts of frother in recycle water were also measured.The contribution of frother and alcohol by-products in the analysis was generally additive for plants using aliphatic alcohol type frothers and decoupled for systems using glycols. Typically, U250C (polyglycol) was used at higher concentration (>10 ppm) than MIBC (aliphatic alcohol) (<10 ppm) or F-150 (polyglycol) (<3ppm).The ability to monitor frother easily will help interpret gas dispersion behaviour and should permit further optimization of flotation cell hydrodynamics and chemistry. The capability to directly measure should help optimize the type, amount and location of frother addition, and to assess frother recycled with reclaim process water.INTRODUCTIONOwing to the lack of analytical methods, the task of determining frother concentration in plant flotation circuits is not routinely performed. Industrial sites seldom outsource analyses that are both costly and inconvenient, due to the necessity of shipping freeze-dried samples to remote testing facilities. A more direct colorimetric method has recently been demonstrated for the laboratory characterization of common industrial frothers (Gélinas and Finch, 2004). The approach, based on the Komarowsky reaction (Penniman et al., 1936; Coles et al., 1942; Duke, 1947), was previously described by Parkhomovski et al. (1976) for methyl iso butyl carbinol (MIBC). The reaction involves the interaction of the OH group of a higher alcohol, concentrated sulphuric acid, and salicylaldehyde, to yield coloured solutions with intensities that can be analyzed by UV-visible spectrophotometry."

Jan 1, 2007

By J. F. MacGregor, M. Hou, D. Hodouin

"RésuméDe nouvelles méthodes efficaces sont maintenant devenues nécessaires pour traiter les quantités massives de données en temps-réel que collectent les ordinateurs industriels modemes. Les méthodes statistiques multi variables comme l&apos;analyse en composantes principales et la projection sur des structures latentes sont des méthodes analytiques bien adaptées aux données industrielles bruitées et mal conditionnées. L&apos;efficacité de ces méthodes est illustrée sur des données historiques collectées dans une usine de broyage et de flottation. Trois cent cinquante observations de quarante quatre variables de procède ont été utilisées pour démontrer les aptitudes de ces méthodes pour l&apos;analyse préliminaire de données, la classification des régimes opératoires, le contrôle de qualité et la modélisation empirique des precedes.AbstractBecause of the availability of powerful industrial computers which collect huge amounts of real-time data in mineral processing plants, there is a need for efficient methods to extract relevant information from them. Multivariate statistical techniques, such as principal components analysis (PCA) and projection to latent structures (PLS), are well suited to analyze these large sets of noisy and ill-conditioned data. The power of PCA and PLS is illustrated on historical data from a grinding and flotation plant. Three hundred and fifty observations of forty-four process variables are used to show the capacity of these techniques for preliminary data analysis, classification of operating regimes, process monitoring, and process empirical modelling."

Jan 1, 1993

By Charles L. Allie

Since Reserve Mining Co. began commercial operations at Silver Bay, MN, some 25 years ago, major improvements in taconite processing technology have become available. In addition, significant new government standards have been imposed on industrial operations. By implementing a $370-million modernization program, Reserve was able to accomplish two major company objectives: the quality of concentrates produced from the Peter Mitchell mine has improved, and the operation meets both present and foreseeable environmental standards. Process modifications at Reserve were designed to: •Reduce the pellet silica content from 9% to 5%; •Increase the pellet iron content from 62.5% to 65.8%; •Implement a tailings disposal system utilizing "best available technology" water quality controls; and •Reduce air emissions by installing "best available technology" air emission controls. By adding dry cobbing, fine screening, and flotation to the concentrating process, pellet silica content has been reduced; the process reclaims and reuses all process waters; all tailings are stored in a zero discharge tailings basin; and all air emission standards are being met. Initial Beneficiation at Silver Bay Reserve&apos;s Peter Mitchell mine at Babbitt, MN, is on the eastern end of the Biwabik iron formation. The open-pit mine is approximately 16 km long, 0.8 km wide, and presently has a maximum depth of about 50 m. Principal constituents of the ore body are magnetite, quartz, and iron-magnesium silicates. The company&apos;s large commercial plant began operating at Silver Bay, 75 rail km from the mine, in 1955. Facilities have historically had the capacity to process 31.5 Mt/a of taconite, containing an average 24% magnetic iron, into 11 Mt/a of iron ore pellets. Reserve&apos;s initial beneficiation process-which existed up to early 1979-consisted of two crushing stages at the Babbitt mine site, two additional crushing and screening stages at Silver Bay, grinding in a conventional rod-ball¬regrind mill circuit, size classification with cyclones, and concentration with magnetic and hydraulic separators. Concentrate produced by that circuit assayed 65% iron and 8.5% silica, with a screen analysis of 94% -44 µm, and a surface area of 9300 cm2/cm3. Pellets produced from this concentrate assayed 62.5% iron and 9% silica (dry basis). Construction began in 1977 to modify Reserve&apos;s operation. Process modifications were designed from pilot scale operations that had been operated and researched by Reserve for more than 10 years. There were two design restraints imposed on the process: economic constraints that Reserve continue to use much of the existing processes and structures in the new operation; and a substantial number of government-imposed permit constraints. In effect, the tailings process was designed first and then a concentrating process was developed that would "fit" the tailings disposal system. Operation of the modified process began in June 1980. Crushing Remains Unchanged No changes in process flow were made at either the Babbitt mine and crushing plant or at the Silver Bay fine crusher. Gyratory crushers reduce run-of-mine taconite to -90 mm-diam at the mine. Taconite is then transported to Silver Bay by intra-plant railroad. There are 10 fine crushing lines. Each consists of a double deck screen, followed by a heavy duty short head crusher, a second double deck screen, and second short head crusher. All screen undersize material bypasses the crushing lines, resulting in an open circuit crushing process. Fine crusher product is approximately 98% - 20 mm, 80% -12 mm, and 50% -10 mm in diameter. Each fine crusher line processes about 400 t/h of crude taconite. Cobbing Provides Aggregate for Tailings Dams The first major process change was the addition of dry cobbing, a dry magnetic separation step between the fine crusher and concentrator. Dry cobbing serves two major purposes in the new process. Its principal function is to provide large volumes of dry coarse aggregate for use in construction of tailings dams. This process rejects about 20% of the fine crusher product as tailings with a size analysis of 98% -20 mm and 50% - 10 mm. These tailings are free draining and have high frictional shear strengths-two key requirements for dam building aggregates. Fine crusher product is conveyed to a new dry cobbing building. Here crushed ore is discharged into one of two 30-minute capacity surge bins. Crushed ore is withdrawn by 12 constant speed conveyor belts; each discharges 500 t of crushed taconite into a dry cobbing machine. Each machine consists of a 3-m-long riffle splitter and two vari-

Jan 12, 1980

By P. T. Craddock, H. V. Paliwal, L. K. Gurjar

The Indian cultural heritage of mining, smelting and the use of minerals and metals dates back to ancient times. Although the exact date of the commencement of such activities in India is not certain, Indians are known to have been familiar with gold, silver, copper, tin and lead and to a lesser extent with iron at least since the Vedic period (Table 1).

Jan 1, 1999