Search Documents

By G. F. Comstock

THE subject of transverse fissures in steel rails has been discussed very thoroughly in recent years from various points of view and the final opinions expressed may be roughly classified into two groups: (1) That these fissures are the result merely of fatigue of the steel and are independent of the quality of the metal. (2) That the quality of the metal and the mill practice must have something to do with them. The first point of view was most-ably and logically presented by J. E. Howard,1 and in the discussion of this paper, as well as in several other preceding publications, Dr. P. H. Dudley, Consulting Engineer of the New York Central Lines, has strongly defended the other opinion.2 The steel makers of the country have naturally rallied under Mr. Howard's banner, hoping to place the entire blame for these. failures upon the railroads with their high wheel-loads, hard steel, heavy traffic, and sometimes inferior roach-bed; while the railroad men,, on the other hand, have been busy accumulating statistics and records in the effort to find an actual reason in the rails themselves that would account for the seemingly haphazard occurrence of transverse fissures under varying conditions and at widely separated points. The view that these fissures were due merely to normal fatigue under alternating stresses seemed most reasonable to the writer until quite recently, because from work clone in this laboratory, as well as the work of other investigators of the problem, no structural differences, in the vast majority of cases, were found between metal at the nuclei of transverse fissures and metal at similar positions in the same rails or in other rails that had not developed fissures. . Within the last year or two, however, since the method of etching polished sections for the microscope with a cupric chloride solution has been tried systematically. on lengthwise sections, passing through the nuclei of transverse fissures, evidence

Jan 11, 1918

By Frederick Rhines

PURE copper that has been allowed to oxidize at an elevated tempera-ture in the air is found to be covered with two distinguishable layers of oxide scale. The outer of these, which is very thin, is composed of cupric oxide, while the inner layer, comprising the bulk of the scale, is made up chiefly of cuprous oxide (Fig. 1a). If a small quantity of an alloying element, such as silicon, is present in the copper, silica particles are found disseminated through the cuprous oxide, deposited most abundantly near the metal surface, and, in addition, silica particles occur to a limited depth within the copper itself (Fig. 1b). It is this inner layer, composed of oxide particles precipitated in a matrix of metallic copper that is known as the "subscale" or the zone of internal oxidation. Under a low oxygen pressure it is possible to produce the subscale without the formation of external layers of copper oxides, thus leaving the metal surface bright and apparently clean while oxidation has occurred, in fact, to a considerable depth within the metal (Fig. 2). Although little is yet known in a detailed way of the mechanism of internal oxidation, the general nature of the process is evident. By virtue of the considerable solubility of oxygen in copper,1 it is possible to bring the alloying element in contact with oxygen within the metallic solid solution. If the oxide of the alloying element is more stable than cuprous oxide, the foreign oxide may form and, since most oxides are relatively insoluble in copper, it will not long remain in solution, but will separate as a precipitate. As the metallic solute is exhausted in the zone of precipitation, oxygen that is constantly being supplied at the surface diffuses farther into the alloy and thus produces an ever-thickening shell of subscale. The distribution of the reacting elements in the subscale and adjoining zones must be somewhat as indicated in Fig. 3. The conditions requisite to internal oxidation to be anticipated are thus: (1) a solubility of oxygen in the alloy, (2) the ability of oxygen to diffuse at an appreciable rate into the alloy, (3) the possibility of the

Jan 1, 1940

By J. L. Gregg

RECENTLY there has been considerable interest in the production and use of, extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made K Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By J. L. Gregg, J. L.

RECENTLY there has been considerable interest in the production and use of extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made. K. Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By J. C. Underwood

"The wear performance of grinding balls under conditions of impact and abrasion is affected by their chemical composition and structure. The selection of appropriate analyses and heat treatments that will provide both abrasion and impact resistance takes into account the effects of certain elements on structure and harden-ability, as well as the over-all effect of composition and hardness penetration on the residual stress pattern developed through heat treatment. Direct quenching from forging temperatures substantially increases hardenability over that obtained in reheat-quench practices, and can be done without undue risk of damage to the ball provided that the harden-ability bears the correct relationship to ball diameter.Average volumetric hardness and percent hardened volume are convenient parameters for quantitatively expressing the response to heat treatment and indicating anticipated wear properties. A number of factors which can lead to reduced wear life as a result of material or processing problems are reviewed and illustrated."

Jan 1, 1959

By AIME AIME

M ODERN metallurgy properly belongs to this century. The great advance made in this science is directly attributable to the discovery of the Roentgen rays. Application of the results of this discovery, together with the more recent corroborating studies in electronic diffraction have definitely and for all time established this science. Metallurgists today speak with familiarity of the atoms of the different metals in terms of their orientation, atomic volumes, lattice structures, dimensional lattice constants distance of nearest approach, and the like. One matter of profound interest, which is quite staggering to the imagination of the human mind, is the enormity of the number of atoms even in a small particle of metal. As an illustration, let us compute the number of atoms in the volume of one cubic centimeter in a single grain of absolutely pure copper. Eighteen and a fraction cubic centimeters equal the volume of one cubic inch.

Jan 1, 1940

By L. I. Boshoff, S. Gracie

This paper discusses pilot and laboratory-scale metallurgical test work conducted on bulk samples from a low grade heavy mineral deposit and provides an overview of basic practical metallurgical techniques applied to ascertain the suitability of existing production plants to process material from this orebody. Previous investigations have shown this specific orebody to be more challenging in terms of mineral beneficiation as it has a high gangue mineral content. Test work was conducted on targeted stratigraphic units based on lithology and assay results to enable identification of the stratigraphic units portraying quality issues. Unit specific metallurgical pilot work has never been conducted on any of the RBM orebodies and is a new field currently being explored. During this investigation focus was placed on potential quality and yield issues for ilmenite product, with particular reference to CaO quality. A basic evaluation of zircon and rutile separability was also conducted. The test work was conducted using a comparative baseline methodology with metallurgical test work methods specifically aiming at mimicking the existing production plant as closely as possible. This enabled not only the likely metallurgical performance to be assessed but also indicated whether current plant design would be suitable to process the low grade ore types into products of acceptable quality at acceptable yields. The methods and findings discussed in this paper indicate that although there is considerable variation between different units, a blended feed can be successfully processed. With unit specific metallurgical data applied to the existing geological block model, expected yields and recoveries using current plant designs could be predicted.

Jan 1, 2007

By Giulliane Meireles Casali Gonçalves Torres

Os arrebentamentos que ocorrem durante o processo de trefilação geram impacto na produtividade e rendimento operacional em função do retrabalho gerado na realização de solda cada vez que o material se rompe e consequentemente no tempo perdido para execução desta etapa. A metalografia é a ferramenta mais eficiente para caracterização das causas dos arrebentamentos durante a trefilação. Faz-se necessário a utilização de microscopia e aplicação dos reativos específicos destinados a revelar a origem da anomalia. O presente trabalho objetiva mostrar os principais tipos de fraturas na trefilação e suas respectivas origens, através do estudo de quatro casos distintos, são eles: fratura resultante de quebras internas (rupturas centrais), fratura dútil por tração, fraturas resultantes de quebras na solda e fraturas lascadas causadas por formação de “pé de corvo”. Os resultados das análises mostram de forma objetiva se a anomalia foi gerada a partir da matéria prima (defeitos superficiais no fio máquina) ou problemas de processo/operacionais durante a trefilação.

Aug 17, 2017

By F. A. Forward

Introduction The main line of ascent in the development of the nickel industry may be traced back through the International Nickel Company of Canada, Limited, to its earliest antecedents, the Canadian Copper Company and the Orford Copper Company. Mining geology is but one aspect of the overall development of this organization, and the stress it has placed on geology grew according to the need. In the early days, intensive geology was not required because ore supply was not one of the main problems of this or any of the pioneer companies. The difficulty then was to find economic methods for reducing the ores to nickel and copper, and markets for absorbing nickel in the face of a limited demand from consumers heavily prejudiced in favour of the New Caledonia product. "Very early in the history of the region it was patent to everyone that to share in the full benefits of the industry the same individuals or company must control the whole of the operation necessary to manufacture the finished product' (1, p. 45). These conditions were fulfilled for the International Nickel Company in 1902 when the Canadian Copper Company (incorporated 1886), with its ample ore supply, took the initiative to merge its interests with those of the Orford Copper (Refining) Company (incorporated 1887) to form the new company which, with reorganizational changes, emerged as the producer of the overwhelming bulk of the world's nickel. The Mond Nickel Company, Limited, entered the field in 1899 with a refining process, and over a period of years acquired ore through purchase of mining properties. This Company operated successfully and independently until 1929 when its assets were joined with those of the International Nickel Company in order to permit the most economic exploitation of the Frood-Stobie orebody in which both Companies were interested.

Jan 1, 1948

By J. Y. Hwang

Alunite has been utilized as raw materials for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores include quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 microns. Adequate separation techniques for such fine particles have not been developed. A new method for the beneficiation of alunite ore is proposed in this study. 'Ibis method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g. an alunite concentrate of 90% grade with 80% recovery, has been obtained from an Utah ore. Techniques for the selective co-flocculation of magnetite and quartz, the separation of the carried quartz, and the recovery of magnetite after separation are discussed.

Jan 1, 1985

By M. I. Panayotova

Some of effluents released by copper smelting plants are highly acidic (pH = 0~1) and contain arsenic and copper in relatively high concentrations (10~20 g/L). Usually arsenic is removed by precipitation with different reagents, such as lime, iron salts, calcium salts, aluminium salts, etc. Precipitates (often voluminous) that require further handling are formed and copper and other valuable components are lost. A method is presented for copper and arsenic extraction from acidic effluents. Effluents are treated in specially designed closed electrochemical cell without chemicals? addition. Gases formed are collected and treated for decomposing the eventual traces of As-bearing compounds and ensuring the environment protection. Initially copper of grade of 85 % is electro-won. Further about half of the initially available arsenic is separated as low-soluble, low volume mixture of intermetallic compounds, oxides and some elemental arsenic. At the next stage the main part of the left arsenic is immobilized as low soluble stable compound. Arsenic content in the treated acid is in the range 0.20~0.25 g/L. Acidity of treated effluent after first two stages remains practically unchanged and the solution can be re-used. Physicochemical and electrochemical processes, governing copper and arsenic removal, are discussed.

Jan 1, 2014

By William J. Wiehagen

The training of mining personnel is a large and continuing activity for the mineral industries. Although safety and skills training has long been recognized as an essential element for reducing injuries and improving productivity, the research literature lacks definitive reports documenting the specific value of such training. The training literature presents a variety of testimonials as to the "benefits of training," but lacks data that specifically tie that training to the performance of the worker.

Jan 1, 1983

By Richard E. Bischke

Computer assisted finite element model analysis, originally developed to study stress distributions in aircraft, has been modified into a versatile mining program, that can be used to assist the engineer with predictions of mine subsidence. International Exploration, Inc. has developed an in-house finite element model program which incorporates a multitude of factors influencing mine subsidence such as mine design, physical rock properties, structure, faults, joints and topography. Finite element analysis of a mine model can mathematically determine the magnitude and direction of the principal stresses within each of the elements forming the model. By comparing the calculated in-situ stresses to the actual rock strengths, high risk regions within a mine can be identified. These potentially unstable regions of the mine can be allowed to fail within the model and the resultant stress redistribution and element movement calculated. Thus, the effects of the mine collapse at the surface can be predicted for the purpose of determining the potential damage, if any, that could occur to surface structures from deep mine failure. Stabilization materials can also be mathematically inserted into the model to design and analyze the effectiveness of subsidence prevention programs. Two examples are presented of the finite element program being used to predict mine subsidence at substantially different geologic and mining provinces in Pennsylvania.

Jan 1, 1984

By Guo Junfeng

The strength of coal mass saturated with gas is an essential parameter in studying the mechanism of gas and coal outburst, and its prediction method. Up to now, there has not been a method for determining the strength of coal mass saturated with gas. This paper describes a new method whereby the strength of in-situ coal mass can be determined and stored continuously and automatically. The simulation results obtained in the laboratory indicate that the new method allows a fast, reliable, inexpensive and convenient determination of the strength of coal mass.

Jan 1, 1992

By William Barrett

IN order properly to evaluate the data related to geomagnetic surveys, it is highly desirable to have all the available information concerning the magnetic properties of the, involved media. This is true of surface as well as subsurface formations and becomes of increasing importance as advancement in instrumental and interpretative technique permits the analysis of relatively slight magnetic reflections of buried masses. Since the magnitude and areal distribution of the usually complex resultant magnetic field at the surface of the earth is a function of the susceptibility1 of the involved matter, it necessarily follows that susceptibility determinations will afford valuable data for geophysical correlation. The present method was developed to meet the need for routine analysis of specimens in the geomagnetic laboratory where it was felt that general utility, ruggedness, ease of manipulation and reproducibility of results was of greater importance than extreme sensitivity.

Jan 1, 1931

By M. S. King

"A simple method is proposed for determining the long-term deformation behaviour of evaporites. The theory developed can be tested by measuring the change in diameter as a function of time of a vertical mine shaft opposite evaporite strata. Ultimate shaft closures predicted by the theory agree well with those calculated with the very much more complex theory of Serata (1968), provided that sufficiently high octahedral shear strengths are used in the former.An analysis of measurements made in an isolated opening in a Saskatchewan potash mine shows that the octahedral shear strength of the surrounding potash and halite was approximately 500 psi several years after the opening was mined. This value is less than that deter-mined experimentally for halite by Serata. The same data indicate, furthermore, that the in-situ octahedral shear strength is decreasing slowly with time.The current controversy regarding the actual deformation of evaporites will only be resolved by the cooperation of potash producing companies in releasing data on the long-term deformation of their mine shafts."

Jan 1, 1971

By V. E. Elliott, C. L. Meyette

THE conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams -and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a useable and relatively simple solution to a bothersome problem. BASIS FOR CLASSIFYING In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will he used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined' as a zone of

Jan 1, 1948

By Niles E. Grosvenor

Several methods have been proposed for determining the tensile strength of rock. These have been tried out over the past several years, but the results have been erratic and of doubtful value. The tensile strength of rock is its weakest property, and this property apparently enters into all failure phenomena whether underground or on the slope of an open pit. Therefore, it is essential that detailed quantitative information is known about the tensile strength of rock if the design engineer is going to select the proper pit' slope, pit orientation, or orientation of underground workings so as to give the most economical and safest mining condition. This quantitative information may be used to orient the pit in such a manner as to allow steep slopes along two sides. This information may possibly be used to orient the direction of either underground workings or open pits so as to decrease powder consumption and to increase blasting efficiency. Hence it is of prime importance that a method of determining accurately the tensile strength of rocks be developed.

Jan 1, 1960

By G. F. Comstock

H. M. BOYLSTON, Cambridge, Mass.-It might be asked, since this test is so simple, why it was not discovered before. It seems to me the explanation is that when we have used the sodium picrate solution, it has .generally been on a very, high-carbon or hypereutectoid steel; to detect . the presence of free cementite, and when we have looked for sulphides, it

Jan 4, 1917

By George Comstock

IT seems a common opinion among metallographists that all light-gray inclusions seen with the microscope in polished sections of steel are manganese sulphide. Examples of this belief are continually appearing, as for instance in the paper by Dr. Henry Fay on manganese sulphide as a source of danger in steel rails,1 and in Lieutenant-Commander Cook's paper on Metallography of Steel for U S. Naval Ordnance.2 Slate FIG. 1-TRANSVERSE VIEW OF THE EDGE OF A SMALL HOT-ROLLED STEEL ROD. ETCHED WITH PICRIC ACID. X 200. colored inclusions are considered to be silicates, and dove-gray inclusions, manganese sulphide. To show the danger in the latter unqualified assumption, it should be sufficient to examine the edge of any piece of steel that is covered with a fairly thick scale, and that has been polished in such a way as to prevent the scale from breaking away entirely below the polished surface. This can be done by protecting the scaled edge of

Jan 12, 1916