Search Documents

By N. Ahmed

The collection of hydrophobic particles in the froth phase in flotation has been studied. A continuous flotation cell was developed, in which the froth phase could be isolated from the pulp zone. Hematite particles, d80 = 87 µm, were floated in the pulp, using a conventional oleate collector, while glass spheres of similar diameter, d80 = 82 µm, were introduced in wash water added to the froth. Four samples of glass spheres, with contact angles between 0 and 82 degrees, were used. The results indicate that the efficiency of collection of the hydrophobic particles in the froth can be very high. The process is strongly influenced by the hydrophobicity of the particles and the surface area available for attachment in the froth. Recommendations for the flotation of particles in the froth phase are made, especially regarding the desirable hydrophobicity as reflected in the contact angle, the froth depth, the solids concentration in the feed to the froth, the air rate and the wash water rate.

Jan 1, 2001

By H. C. van Zyl

Mine water in the Upper Olifants River Catchment in Mpumalanga(upstream of Loskop Dam) is at times discharged into local streams, resulting in local acidification and regional salination of surface water resources. Pollution of surface water can be prevented by collecting and treating mine water to a quality where it could be re-used without restriction (Cleanwater 2020 Initiative). Mine water in the Olifants River Catchment currently amounts to only 4,6% of the total water usage, but contributes 78,4% of the sulphate load. Limestone and lime treatment is the most cost-effective technology for neutralization and partial sulphate removal of acidic/sulphate-rich water to sulphate levels of less than 1500 mg/l due to precipitation of magnesium and removal of the associated sulphate fraction (through gypsum crystallization). Neutralized mine water of this quality may be suitable for irrigation. A number of alternative desalination treatment technologies were investigated (subsequent to gypsum crystallization pre-treatment) where treated mine water must meet more stringent quality requirements (e.g. less than 200 mg/lSO4). The capital cost of these processes varied between R4 million/(Ml/d) and R10million/(Ml/d) and the running cost between R2/m3and R5/m3. Water usage in the Upper Olifants River Catchment currently amounts to 947 Ml/d (including the power stations), and will increase to an estimated 1385 Ml/d by 2020. The additional water demand by2020 (438 Ml/d) will have to be supplied by importation from neighbouring catchments, and more efficient utilization of the local water resources, including excess mine water. Various levels of treatment are required to make mine water suitable for the following potential applications (acceptable treated water sulphate concentration shown in brackets): irrigation (2000 mg/l), coal processing plant (1000 mg/l), general industrial use (500 mg/l), discharge to public streams (500 mg/l), potable use (200 mg/l) and cooling water in power stations (20 to 40 mg/l). The following two options, or a combination thereof, can be considered for management of excess mine water in the Upper Olifants River Catchment: ?Collection and treatment of excess mine water to a quality suitable for selected urban and industrial applications (Option A) ?Collection and treatment of mine water to a quality suitable for irrigation (Option B). The estimated capital and running cost for Option A amounts to R528.5 million and R55.7 million/year, respectively, compared with R68,2 million and R11,9 million/year for Option B. It is recommended that Option B be investigated for implementation in the short to medium-term. Option B was selected due to cost benefits and the initial favourable results obtained by a joint Water Research Commission and Coal Industry initiative where mine water is used for irrigation. Option A may become feasible in the long-term to ensure maximum environ-mental protection and reduced treatment cost as a result of anticipated technological improvements over the next 5 to 10 years.

Jan 1, 2001

By Paul C. Lingo

Two recent antitrust cases, coming from widely separated areas, different industries and involving wholly different facts were decided by the Supreme Court on June 7, 1965. The decisions in these two cases may well prove to be the most important and far-reaching decisions in the field of labor law that have been handed down in the last 24 years. These cases, although quite dissimilar factually, had one common element. In both, the gravamen of the antitrust violation was bottomed on the terms of labor agreements negotiated by a multiemployer group. These cases are usually referred to as Pennington1 and Jewel Teat. Since a number.-of references will be made to the antitrust laws, it may be well to state briefly the applicable portions. Section I of the Sherman Antitrust Act makes "every contract, combination in the form of trust or otherwise, or conspiracy, in restraint of trade or commerce among the several states, or with foreign nations, is declared to be illegal...". Section 2 imposes criminal sanctions against "Every person who shall monopolize, or attempt to monopolize, or combine or conspire with any other person or persons, to monopolize any part of the trade or commerce among the several states...". Under Section 4 of the Clayton Act a person who sustains damages as a result of a violation of the antitrust laws is entitled to recover treble damages plus costs.

Jan 1, 1965

By Andrew Fletcher

AS good health is the most important asset in life, the development of healthful conditions should be the one common meeting ground of agreement between management and labor. Health should not be a subject to be pulled apart, shoved around, or bargained about. Differences of opinion may exist in the procedure and techniques employed in approaching the goal of maintaining the health of workmen, and in the method of increasing the ultimate profit of the employer by improved working and living conditions. Such matters are doubtless appropriate subjects for discussions between the interested parties, but techniques are only tools. If an employer fails to remedy a hazard or a menace which contributes to poor working condlions, this constitutes a legitimate grievance. It should not be necessary, however, nor is it desirable that fundamentals of health maintenance become matters of collective bargaining, any more than should the principles of management and engineering. I have been especially concerned during the last few months with the propaganda in collective bargaining negotiations throughout the country for including in union contracts a given number of days of sick leave with pay. We all

Jan 1, 1946

By P Gnnther, A M. van Niekerk

Coal mining operations in the Upper Olifants River Catchment in the Mpumalanga Province of South Africa are challenged with the increasing production of excess mine water that cannot be fully managed by existing practices of pollution control at source, recycling, and reuse on mining sites, storage and limited release to the natural water course. In contrast to this, the Olifants River Catchment is experiencing water stress and insufficient water is available to satisfy all water quantity and quality requirements for future industrial and municipal growth. It is estimated that the catchment has a deficit of 192 million m3 per annum if the reserve water requirements are taken into account. The future increased water requirements can be met by water transferred to the Olifants River Catchment from adjacent catchments. The cost of transferred water is likely to be substantially higher than the current cost of water supplied to local municipalities, commerce and industry. BHP Billiton and Anglo Coal Corporation are working together to jointly implement water management strategies that will contribute to the achievement of in-stream and dam water quality and aquatic objectives for the catchment. Consideration is now being given to the treatment and beneficial use of excess mine water. This will inaugurate a new era for the coal mining industry in South Africa, in which a pollution threat to the water resources in the Upper Olifants River Catchment is converted into a water source for beneficial use. Three potential mine water reclamation and reuse schemes have been identified and this paper details the technical, institutional, legal and financial considerations in the implementation of these schemes.

Jan 1, 2006

By J. A. Meech, R. J. Tucker

"Since the establishment of froth flotation as an effective method of mineral beneficiation there has been both academic and industrial interest in the levels of the various reagents required to perform the desired separations. Academic interest was spurred by a desire to understand the mechanisms involved - industrial interest by a need to improve the efficiency of the process. These efficiency improvements can take two forms: cost reductions due to reduced reagent consumption and/or improved separation efficiencies. The latter are indicated by either improved grade-recovery relationships for removal of a valuable mineral from gangue, or improved separation of two similar valuable minerals.The processing of lower grade ore bodies at higher tonnage rates has necessitated increased interest in both reagent consumption and metal recovery. Furthermore, the development of accurate and functional on-stream analysis equipment in the 1960's and 1970's has allowed for a better understanding of the dynamic processes involved in a flotation circuit and has required a more concrete statement of the relationships and reactions between the minerals and chemicals in the flotation pulp. Development of these relationships is necessary in order to make use of on-stream analysis to control the process at, or near its more efficient level."

Jan 1, 1984

By G. Wang

With the depletion of easy-to-treat phosphate resources, low quality phosphate ores with high carbonates, particularly dolomite impurities have to be mined to meet the agricultural demand because of the continued growth of world population. The separation of dolomite from phosphate has been recognized as one of the most difficult subjects in mineral processing due to the similarities in their physical and chemical properties. Flotation is considered the most important approach for beneficiating both easy-to-treat and high impurity phosphate resources. There is no doubt that the development of reagents is the key for achieving satisfactory separation performance through flotation process. In order to separate dolomite from phosphate, Arr-Maz Custom Chemicals has made great efforts in developing flotation reagents for removal of carbonates from phosphate ores of different origins worldwide. This paper describes some flotation reagents and processes for the separation of dolomite or/and calcite impurities from phosphate in the ores from different locations.

Jan 1, 2010

By Arvid E. Anderson

The paper describes the unique operating features of the Lebanon Concentrator Plant wherein both magnetic concentration and froth flotation are used. Chalcopyrite is selectively floated by the use of dual collectors, Aerofloats and secondary butyl xanthate. Both potassium ethyl xanthate and sodium isopropyl xanthate (dual collectors) are dissolved and emulsified with pine oil for the flotation of the pyrite. Sketches describing the plant operations are presented and plant operating metallurgical results obtained are also given. The optimum production of minerals by the froth flotation process is normally achieved [ ] smooth operating conditions, The process, because of its many variables, becomes an art as well as a science. Therefore, any phase of the operation which will aid the operator in his control of the numerous variables will help produce a smoother operating plant, One of the most important variables which the operator deals with is the addition of reagents, These are usually costly items and should be used discretely with minimum amount of waste, The danger is that ,this emphasis may reduce the reagent amount to a point below that required, or, on the other hand an excessive amount is added, Both conditions usually yield poor results. The drea of the metallurgist is to provide the operator with the tools enabling him to produce a good mineralized froth at all times. Normally the operator has no control concerning the type of reagents which he must use. This has usually been worked out for him in the laboratory and by plant-scale tests. He does have limited authority to control the amounts of the reagents at his disposal. This, I believe, is as it should be. However, the operator should be provided with the best combination of reagents for his particular job. The providing of this combination of reagents for his particular job, The providing of this combination is often difficult, yet it is very important in order to yield good results, With this in mind, the dual collector idea was introduced for the selective flotation of chalcopyrite, and also later for the flotation of pyrite at the Concentrator Plant of the Bethlehem Cornwall Corporation in Lebanon, Pennsylvania, Supplying several types of collectors has given the operator an additional effective tool, even though great variations are encountered in ore tonnage treated and in ore composition, This paper deals with the use of the dual collectors and with the addition of the reagents in the form of a pine oil emulsion, or more accurately, a pine oil suspension. It is hoped that other operators may find the ideas helpful. There does not seem, to me, to be definite scientific fact which would substantiate the necessity for the use of dual collectors. However, in actual operations, the metallurgical results at Lebanon became more uniform with the use of dual collectors, I look upon it as an "insurance policy" which greatly aids the operator during those periods when he is having trouble, One theory has been advanced, i.e. one collector has a greater tendency to float the coarser minerals, whereas the other one may float the finer ones. Consequently, a combination of the two collectors will result in optimum recoveries, There has been some evidence that this is true, but it is not conclusive, on the other hand, the use of a xanthate-pine oil suspension (or emulsion) should speed up the surface reaction of the collector with the sulfide minerals, result¬ing in more uniform flotation, This has definitely happened in our particular case. A more interesting unexplainable observation has also occurred; i.e., the xanthate solution does not appear to lose its strength as rapidly when it is in the form of an emulsion (or suspension), This was first observed when a 50 gallon drum of a 20% ethyl xanthate solution was taken to Wilmington, Delaware, for a laboratory test, using a homogenizer to produce the xanthate-pine oil emulsion. Upon arrival, the drum of xanthate had developed a considerable internal pressure, The relief of this pressure was accompanied by a strong odor, When the emulsion was returned to Lebanon for the plant test orders were issued to release the pressure prior to emptying the emulsion. Nopressure had developed within the drum and there was no unusual odor present, Since this time it has been observed that xanthate pine oil suspensions have greatly decreased the possible decomposition of the xanthate solutions. In fact, suspensions have been exposed for more than a month without apparently effecting their reactions in the flotation plant. On the other hand, we found that the regularly mixed concentrated xanthate solutions, after standing for several days, did not give the same results as the freshly made ones. This effect was greatly reduced by the use of xanthate pine oil suspension (or emulsion)

Jan 1, 1958

By Frank Cappuccitti, Stephen Chryssoulis, Stamen Dimov

Surface organic microanalysis of platinum (Pt) and palladium (Pd) minerals by TOF MS1 is an attractive complement and potential alternative to conventional collector screening methods. Its attractiveness lies on its ability to focus on individual Pt and Pd mineral particulates, therefore providing a more targeted approach. The only requirement is knowledge of the occurrence (mineral composition, grain size and association) of Pt/Pd in the feed sample. This newly developed technique can detect, and identify collectors and quantitate loadings on individual Pt/Pd mineral particulates at plant concentration levels. Using this technology, collector loadings were measured on Pt and Pd metal plates and on PtS2 and PdS particulates which had been exposed together to aqueous solutions of different collectors. Thus, data were obtained on collector selectivity, the effect of sulphur; and of depressants, the latter in combination with TOF-LIMS2 results. Staged rougher tests on North American and UG-2 ores linked Pt/Pd flotation kinetics with collector loadings and ultimately grade/recovery.

Jan 1, 2003

By B. Nanthakumar

The impact of stockpile oxidation on chalcopyrite was studied through collectorless and collector-induced flotation conditions. In both cases, the Cu grade-recovery performance of stockpiled ore showed relatively poor concentrate grades with respect to that of a fresh sample. However, the oxidation had a minor effect on chalcopyrite recovery itself. The poor concentrate grades resulted from dilution effect primarily by excessive flotation of pyrrhotite. Size-by-size analyses indicated that for the collectorless flotation, the recoveries in the coarse and fine particle-size regions, were higher for fresh ore than for stockpile sample. A greater impact was seen in the coarse size regions for both types of sample, compared to the collector-induced case. The Cu recoveries showed a remarkable increase in the coarse size range for both samples when a collector was used. However, the case for stockpile sample was a marginally higher compared to the fresh sample. This difference has been offset by an opposite trend that was observed between these two samples in the fine size region. It is concluded that in contrast to the case with nickel-bearing sulphides, stockpiling conditions do not show a significant adverse effect on behaviour of chalcopyrite due to its strong floatability, regardless of oxidation.

Jan 1, 2007

By S. Kelebek, G. W. Smith

Four samples of galena, each prepared differently, dry ground chalcopvrite and real gar have shown various quantities of liberated sulfur corresponding up to nine equivalent monolavers on their surfaces as determined by the solvent extraction/UV analysis of sulfur using ethanol. The pretreatment of a dry ground galena sample with acidified ammonium chloride or neutral, saturated sodium chloride solutions rendered the mineral readily floatable. The collectorless floatabilities of galena pretreated with the former solution and of drv ground chalcopvrite have been evaluated in reference to the natural floatability of sulfur using the critical surface tension of floatability approach with aqueous methanol solutions. It is shown that the amount of sulfur- on these samples can be correlated with their flotation rate, which was found to he first order within the critical surface tension range. The larger the concentration of surface sulfur, the faster the sulfide mineral floats, thus, the greater its flotation rate constant.

Jan 1, 1990

By R. P. King

Held on the 22nd March 1972 at Kelvin House. Four papers were presented at this colloquium, which was attended by approximately 120 people. The first paper, 'Flotation Research Work at the N.I.M. research group, University of Natal on the modelling of a Flotation Process' was presented by Dr R. P. King, the leader of the N.I.M. Research Group in the Department of Chemical Engineering at the University of Natal. A discussion panel, under the chairmanship of Dr R. E. Robinson with Mr M. Dawson (PMC), Mr E. Roux (FOSKOR), and Dr B. K. Loveday (NIM), discussed the potential application of the theoretical work on flotation modelling to industrial processes, and alternative approaches to providing a way of control of flotation plants. The second paper, 'Fundamental Studies of the Flotation Process the Work of the National Institute) for Metallurgy', was presented by Dr N. P. Finkelstein. The discussion panel for this paper was under the chairmanship of Professor D. D. Howat,and had as its members Mr H. P. Carlisle (JCI), Professor D. le Roux (University of Pretoria), and Mr E. Rudolph (Anglo American Research Laboratories). A lively discussion on this paper ensued, with several contributions from the floor. After lunch, Mr S. K. de Kok, Assistant Consulting Metallurgist, Anglo Vaal, presented a paper on 'The Flotation of Copper and Zinc Sulphide from Prieska Ore'. The paper was discussed by a panel comprising Dr V. C. Lovell (NIM), Mr A. Gilbert (General Mining), and Dr D. Legge (Anglo Vaal), under the chairmanship of Dr L. Bushell. This discussion, in which many members of the audience participated, revolved around the difficulties associated with the production of copper and zinc concentrates and the lack of fundamental information on the behaviour of copper and zinc sulphides in flotation. The final presentati0n was a paper, 'The Recovery by Flotation of Cassiterite contained in Gravity Concentration Plant Tailings', presented by Mr E. B. Viljoen (Metallurgy Department, Goldfields South Africa Limited). The discussion, led by a panel consisting of Mr O. Tant (Goldfields Laboratories), Mr J. Levin (NIM), and Mr R. I. Shanks (NIM), under the chairmanship of Mr H. Cross (Goldfields South Africa Limited) referred particularly to the use of new reagents for the flotation of tin, with particular emphasis on the fundamental relationship between reagent composition and its ability to float this type of mineral.

Jan 4, 1972

A knowledge of the mechanics of wave propagation through the earth is essential if reliable communication systems are to be designed for coal mine environments. To obtain a reliable basis from which accurate propagation predictions could be drawn, a series of theoretical studies have been prepared for the US Bureau of Mines by Mr. Ramsay Decker of Spectra Associates, Inc. through a subcontract with Collins Radio Group. These reports formulate the analytical techniques from which we may derive frequencies and antenna configurations that yield the optimum signal-to-noise ratios over the greatest distances in mine environments. The reports of sections 2 and 4 deal with analytical techniques for determining the signal-to- noise ratio within a mine environment for loop-to-loop and line source-to-loop antenna con- figurations. The analytical results of these reports were then implemented into computer programs to obtain predictions concerning through-the-earth signal propagation. These preliminary predictions are based on noise data compiled by Bensema, Maxwell and Stone, and WVU prior to the extensive research conducted by the National Bureau of Standards (NBS). These initial measurements indicated a 20- to 30-dB lower noise level than that measured recently by NBS. The recent NBS data is that used by Collins in the final predictions. The following outline indicates the order and subject matter treated in the subsequent sections: Section 2 - Signal-to-Noise Analysis for Loop-to-Loop Mine Communications Section 3 - The Horizontal Electric Dipole Section 4 - Signal-to-Noise Analysis for Down-Link Line Source Mine Communications Section 5 - LF Communication Section 6 - The Application of Recent NBS Noise Data to Mine Communications Section 7 - Analysis of Mine Communication Propagation Programs

Nov 15, 1974

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract SO122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine. Field testing was conducted during the last week of November 1972, at a coal mine operated by Inland Steel Company, near Sesser, Ill, and in the Robena No. 1 Mine, Waynesburg, Pa, on 12 March 1974. The tests included uhf propagation losses and noise (200 MHz to 1 GHz) in the Sesser, I11 mine location and vlf propagation loss and noise (1 to 200 kHz) in both of the above locations. The basic experimental parameters were frequency, polarization, antenna type/orientation, and distance. The following reports treat the various aspects of the test programs in detail. Since different antenna configurations were used in the two mines, each report contains its own experimental predictions drawn from its corresponding test activities. A test equipment list and block diagrams of typical experimental setups for the tests of section 2 are contained in appendix A.

Jan 1, 1974

This report is a compilation of all information obtained in accordance with the requirements of contracts SO122076 and H0232056. A series of eight coal mines were visited to determine their communications usage and requirements. Presently available equipment was surveyed and evaluated to determine its applicability to the needs of the mines. The equipment studied includes that made by the following companies : Anaconda Telecommunications Division Andrew Antenna Bendix Communications Division Collins Radio Group of Rockwell International Executone Communication and Sound Systems Gau-tronics Mine Safety Appliances Company Motorola Communications and Electronics, Inc National Mine Service Company Plessey Communications Systems Corp Pye Electronics Limited Reach Electronics Set Com Corporation Sonex Incorporated Mine visits and in-depth interviews were made alt the following sites: Robena No. 4, Pennsylvania Greenwich Colliery Mines, Pennsylvania Somerset Coal Mine, Colorado Keystone No. 1, West Virginia Harris Mine No. 1, West Virginia Baldwin Underground No. 1 Mine, Illinois Lovilia No. 4 Coal Mine, Iowa Orient No. 3 Coal Mine, Illinois

Nov 15, 1974

A working understanding of present coal mine communications equipment and its usage is an essential prerequisite to the determination of future communications systems needs. As a means of gaining this understanding, a field survey program was planned and implemented. The plan formulated called for obtaining both qualitative and quantitative data from three main areas of interest: the types, physical condition, and performance characteristics of equipment presently used in the sample of mines to be visited; the relationship present communications has to safety and productivity; and the practical, future communications needs as de- rived through interviews with present mine management. In compliance with the original plan, the type and physical condition of equipment in use was found through at-mine interviews of personnel responsible for installation and maintenance. Further evaluation was made through the review of equipment instruction books and maintenance manuals and through in-mine inspection of communications equipment and signal distribution networks. The performance characteristics were determined through listening to conversations and noise levels and by talk-testing from randomly selected stations throughout each mine. System operation was evaluated by asking communication system users their opinions and by noting any difficulties personnel had using the systems. Plans in the second area of interest--that of relating communications to mining operations-- were to observe mining operations and usage of communications; to gain insight through interviews with mine management, from mine superintendents to section foreman; and to look for correlation between communications, production, and safety. Lastly the communication systems needs and requirements were determined from first hand interviews of mine personnel, from the analysis that lead to the individual reports on the eight mines, and from an overview of all of the mines studied. The latter was done to find commonality between the needs of the individual mines such that system requirements having the greatest universal value could be derived, thus lowering per-mine cost of equipment through economics of scale. Armed with tape recorders, backgrounds in communications technology, and with an interview questionnaire that was improved as experience was gained, engineers visited the eight mines to obtain the raw data from which the needs and requirements could be developed through analysis. During the first part of the program two days were spent at each mine so that interviews and tours could be completed, and so that full eight hour shift phone usage recordings could be obtained for statistical analysis. One day visits were sufficient for those trips where tape recordings were not made. During the later trips less attention was given to the statistical nature of communications, and more to how communications relates to the total mining operation.

Nov 15, 1974

By R. C. Bunge

Many minerals float best with fatty acids in the intermediate pH range. For example, fluorite, a semi soluble salt mineral, exhibits a maximum contact angle and a maximum flotation recovery in the pH range of 6-8 after conditioning in a palmitate solution (fig. 1). The maximum in flotation coincides roughly, as many researchers have observed, with the boundary of bulk precipitation of the fatty acid. According to fig. Z this boundary is in the above case of 5xl0-7 M palmitate approximately at pH 6.3. For assessing the phenomena occurring at the bulk precipitation boundary of fatty acids, the surface tensions of carboxylate solutions have been measured under various conditions. Fig. 3 shows the surface tension development of palmitate and myristate solutions of increasing concentration at pH 12. Also shown are the bulk precipitation edges (BPE) of the respective solid species that is stable under these conditions, that is the potassium acid soap, HKAZ. Both curves display a similar behavior. As the concentration of carboxylat,e increases, the surface tension decreases, until a minimum is reached at which the curves level off. The decrease of surface tension with increasing carboxylate concentration is generally taken to indicate the surface excess of the carboxylate ion. The point where the curve suddenly levels off has not yet been explained. While it is well known that the onset of micellization (CMC) may cause such an inflexion of the surface tension curve, this cannot be the case here because the position of this point depends, as shown in fig. 4 for palmitate, on pH (the CMC is generally independent of pH). We believe that this point indicates the precipitation of a colloidal acid soap (colloidal precipitation edge, CPE) before the bulk precipitation of this species sets in (BPE).

Jan 1, 1994

By SAIMM Journal

COLLOQUIUM ON COMMINUTION The Institute has arranged a colloquium on the above topic to be held on 13th March, 1973, at Kelvin House. The following papers will be presented: 'Peripheral Discharge Mill', by A. H. Mokken, Union Corporation Limited

Jan 1, 1974

By Gaston Giuliani, Jérome Massot, Didier Bourlès, Lionel Siame

"Abstract - We present a new approach for the evaluation of the potential of emerald reserves in gem projects using beryllium (Be) mobility. The distribution of Be in the different phases of hydrothermally altered (albitized) black shale hosting Colombian emerald deposits indicates that Be mobility is associated with the breakdown of Fe-Mn oxyhydroxide phases. The amount of Be that can be mobilized (~0.7 x 10-6 g/g; i.e., 0.7 ppm) may represent up to 18 wt% of the total Be contained in the black shale. A mass balance calculation applied to a well-constrained alteration zone of the Chivor mines, and based on the quantification of Be that can be mobilized under hydrothermal conditions, gives an estimate of the total gem reserves of these mines. Resumé - Une nouvelle approche, basée sur la mobilité du béryllium (Be) pour l’évaluation des réserves d’émeraude dans des projets d’exploitation de gemmes est présentée. La distribution du Be dans les différentes phases minérales de schistes noirs hydrothermalisés (albitisés) qui contiennent les gisements d’émeraude colombiens, indique que le Be mobilisable se trouve dans les oxyhydroxydes de fer et de manganèse. La quantité de Be potentiellement mobilisable (~0,7 x 10-6 g/g; soit 0,7 ppm) constitue jusqu’à 18% poids du Be global contenu dans le schiste noir. Un bilan de masse appliqué à la zone d’altération hydrothermale des mines de Chivor et basé sur la quantification du Be mobilisable, donne une première estimation des réserves à émeraude de ces mines. rieur."

Jan 1, 1999

By Andrew Meyer

As a producer of gold and platinum, Colombia is most emphatically an important country. Last year it produced 656,000 oz. of gold-twice as much as any other country in South America, in fact accounting for a third of the production of that continent. In platinum, world data for 1941 are not available, but in 1939 Colombia exported 39,000 oz., apparently ranking fourth among the world's producing countries, being exceeded only by Canada, Russia, and the Union of South Africa. Colombia was always a mining country. Centuries before the Conquest, Indians mined gold, copper, silver, salt, and emeralds. The Spaniards simply intensified mining. The Bank of the Republic states that from 1493 to 1940 52,177,427 oz. of gold was produced by Colombia, and official Chocó statistics show that about $60,000,000 worth of platinum was mined between 1908 and 1941. These figures are impressive indeed considering that only rich pockets and surface showings were mined by the ancients.

Jan 1, 1942