Search Documents

By D. J. Droppert

This paper describes the precipitation-production of crystalline scorodite (FeAs04.2H20) from arsenic-rich sulphate-based metallurgical solutions at ambient pressure (95°C). Arsenic is precipitated by means of a controlled precipitation technique in which the supersaturation of the solution is carefully controlled. By controlling the supersaturation in the presence of seed material. the formation of amorphous ferric arsenate is prevented. Scorodite is known to be the most stable As(V) compound and is therefore preferred as host mineral for arsenic immobilization. The effect of the following parameters on the preCipitation behaviour and kinetics of scorodite are discussed: Type of base seed concentration initial [As]. sulphate concentration. neutralization rate. seed recycling and method of Fe(ll!) addition to Fe-deficient arsenic solutions.

Jan 1, 1996

By N J Welham

A commercial enargite concentrate was mechanically milled in inert and oxidising atmospheres for 10 hours. No substantial effect was observed in either an inert atmosphere or in air other than a broadening and weakening of the diffraction peaks. Milling dry in oxygen or wet in air was dramatic with a significant reaction occurring which formed arsenolite, As2O3 and CuSO4.5H2O, both of which are readily soluble.A small amount of SO2 was also formed. Dissolution in acid left CuS as the major phase implying incomplete oxidation. The small fraction of tennantite in the sample was comparatively resistant to oxidation.

Jan 1, 2001

By Oscar Perales Perez, Atsuo Kasuya, Kazuyuki Tohji, Yoshiaki Umetsu

"The removal of iron and various heavy-metal ions by their incorporation into stable ferrite-type precipitates at 25°C is a promising alternative to clean up large volumes of polluted aqueous effluents. Our research work investigated the conditions to produce magnetite and various M-bearing ferrites (where M: Zn, Cu, Co, Ni, Cd, etc.) directly from aqueous solutions at 25°C by simultaneous control of the oxidizing conditions and pH. The formation of the solids was followed by monit9ring the oxidation-reduction potential (ORP) and rate of proton release during the aerial oxidation of the suspensions at constant pH (contact stage). Only mildly oxidizing conditions, represented by ORP values between -110 mV and -150 mV and a moderate oxidation rate of Fe(II) species were conducive to well-crystallized ferrites at ambient temperature.' It was also found that increasing the Fe/M mole ratio in starting· solutions enhanced the stability ·of the M-bearing ferrites at ambient temperature. When the formation of the ferrite was incomplete, aging of the sludges in their mother liquors at 25°C promoted the crystallinity of the precipitates. The mentioned conditions ·favored the suitable progress of the ferrite-forming reaction involving the oxidation of Fe(II) entities, subsequent hydrolysis of produced Fe(III) species and dehydration of the intermediate:· Furthermore,· the ferrite formation at· low temperature permits the elimination of iron and co-existing heavy metal ions to sufficiently low concentration.In tum, the characterization of the precipitates evidenced their magnetic nature (room-temperature saturation magnetization above 60 emu/g) as well as the effective incorporation of target metal ions into the ferrite structure."

Jan 1, 2000

By Roger M. Zimmerman

The G-Tunnel heated block experiment is being conducted on the Nevada Test Site (NTS) as part of the Nevada Nuclear Waste Storage Investigations project (NNWSI). The purpose of the ambient temperature testing ph se is to evaluate rock-mass mechanical properties of a block (- 8 m3) under biaxial stress changes up to 7.5 MPa above an initialization in situ value of 3.1 MPa. Results indicate that the modulus of deformation ranges from 9.7 to 17.0 GPa and Poisson's ratio ranges from 0.21 to 0.33. In general, the higher values of the modulus and Poisson' s ratio were influenced by fracture propagations parallel to the compressive stress field. Other measurements indicated that cross-hole compression (p) wave velocities and single fracture permeability values were relatively insensitive to stress changes above the in situ value.

Jan 1, 1984

Acid mine drainage containing heavy metal ions is a large environmental problem facing the mining and mineral processing industry. The femte coprecipitation is a novel technique for removing heavy metal ions from waste water, recently applied to acid mine drainage. The fenite precipitation is usually performed at high temperature and therefore if applied in conventional manner, it becomes uneconomical to treat large quantities of acid mine drainage. In this paper the ferrite precipitation at ambient temperature-is &died. The possible mechanism of ferrite formation is discussed Experimental results from Noranda Tailing and Berkeley Pit water treated by this process are presented.

Jan 1, 1994

By John Zeni

In Australia during the 1990s, Zeni Drilling took on several demanding shaft boring contracts. This paper describes the safety, operational, technical and environmental advantages derived through the implementation of mechanized boring methods for two of these projects. The paper first describes a 3-meter (10 ft) diameter access shaft blind bored from an underground location to 440 meters (1,444 ft) deep for a gold mine in Tasmania. The construction of a 5.8-meter (19 ft) diameter, 515-meter (1,690 ft)deep ventilation shaft for a longwall coal mine in New South Wales is also described.

Jan 1, 2001

By John Fritz

THE John Fritz Medal was presented to Ambrose Swasey of Cleveland, Ohio, in the Auditorium of the Engineering Societies Building, in New York, on April 23. Charles F. Rand, Chairman of the Board of Award, presided and, after speaking very briefly of Mr. Swasey, whose friend he has been for a great many years, ,introduced Gen. William Crozier, formerly Chief of Ordnance, U. S. Army, who spoke most entertainingly of, Mr. Swasey's accomplishments in designing and manufacturing instruments of precision, particularly for the use of artillery in range finding: Dr. William Wallace Campbell, Director of the Lick Observatory, and President of the University of California, described Mr. Swasey's, contribution to astronomical advancement by his notable development of the largest telescopes in this country.

Jan 1, 1924

By B Hayes

The Ambuklao and Binga Rehabilitation Project is a 175 MW hydro power project currently under construction across dual sites in the north region of Luzon Island, Philippines. When it was built in 1956, the Ambuklao Dam harnessed the second largest hydro-electric reservoir in Asia. However, due to landslide erosion and prolonged silt infiltration caused by an earthquake in 1990, the power plant has been rendered inoperable since 1999.To bring the power generating facility back to life, the project scope entails the rehabilitation and construction of civil structures, shafts and tunnels. A major component of these works is the decommissioning of a section of the seven metre diameter headrace tunnel by installing a concrete plug. The headrace tunnel is part of a closed waterway system that connects the dam via a shaft, exhibiting a hydrostatic pressure of 13 bar (1300 kPa) at the location of the new tunnel plug. In addition, the power station ball valves have seized ajar and the damaged intake riser is unsafe toaccess thereby requiring the plugging operation to be carried out under live flowing conditions.Working under hydrostatic pressure and live conditions, the headrace plug will be an underwater tremie pour operation that includes drilling and concrete injection through blow out preventer caissons installed in the floor of an underground chamber above the tunnel. The purpose of this paper is to describe the key engineering and planning components involved in this operation including pre- and post-grouting, chamber crane, sonar, local water compensation, jet flushing, drilling, caisson installation, and concrete design, production, delivery and placement. The success of this task rests on the strategic preparation and operational management of risk and safety in a challenging rural environment.

Mar 8, 2011

Schedule of Events

Jan 8, 1950

Though the mining industry is beset with problems-a broad slump in metal prices, a rash of acquisitions and takeover attempts, rising capital costs, and an aggressive Canadian energy program-there was an under-current of optimism at the 1981 AMC conference that's been missing at industry meetings in recent years. The industry anticipates a turnaround in the 1980s, buoyed perhaps by the new spirit of cooperation from the Reagan administration. For the first time in years, it appears that Washington and the mining industry share mutual goals for developing the nation's resources. A number of prominent Reagan officials were on hand during the three-day conference in Denver, September 28-30, to reassure conferees that restrictions plaguing energy and minerals development would be eased. Interior Secretary James Watt and other government speakers promised cooperation in bringing balance to federal public lands policies, a review of regulations that have hampered the industry, and prompt action on domestic minerals policy. Daniel N. Miller, Jr., assistant interior secretary for energy and minerals, said, "It is our intent to dismantle the overhearing bureaucracy that has stifled mineral and energy exploration. We know that Interior's rules have shackled the mining industry in recent years, and we know that those rules must be eased." Miller noted that the administration will not permit mining on national park lands or wildlife refuges, but added that "we must assess a variety of uses of public lands ... we will restore lands to multiple use where practical." EPA administrator Anne Gorsuch assured industry representatives that the administration intends to work within environmental laws and with Congress to review and revise water, soil, and air pollution policies. "We have a strong commitment to see that there are major mid-course corrections" of air regulations, Gorsuch said. Support from these "new friends in Washington" will be crucial in light of the serious problems pressuring the industry. Copper prices have plunged to almost three-year lows and prices for molybdenum, gold, and silver have slumped. Earnings are down and today's high interest rates prevent a quick turnaround. Companies are on edge after the recent takeovers of Kennecott, St. Joe Minerals, and Texasgulf Though the companies may benefit from the major injection of capital that large energy firms can provide, many observers fear the new parent companies won't be willing or able to survive the cyclical metal markets. Arco and Gulf Resources, for example, have been criticized for closing Anaconda's Montana copper facility and the Bunker Hill unit in Idaho, respectively. Canada's national energy program has brought additional pressure on the industry. This policy, which emphasizes Canadian majority ownership of the country's energy sources, resulted in acquisition of Texasgulf's Kidd Creek lead-zinc-silver complex by Canadian and French interests. In response, the American Mining Congress adopted two resolutions on takeovers. One calls for the US government to review laws regulating tender offers and takeovers "to better ensure that principles of fairness and sound investment policy govern such transactions.'' The other asks the government to demand "fairness and reciprocity" as a basis for US policy governing international trade in minerals and investment relations with other countries. AMC's shopping list included four other priority goals, aimed primarily at the Interior Department: • Prompt implementation of Interior's efforts to bring order and balance to rules governing access to public lands for exploration and development. • Statement by the President of a comprehensive and coherent domestic minerals policy. • Amendment of the Clean Air Act to remove impediments to productivity and barriers to economic development that are not necessary to essential goals of the act. • Development of new approaches to better achieve worker health and safety in the most cost-effective manner without penalizing productivity. Almost 6000 mining industry executives attended the 1981 convention-the largest in AMC's 84-year history. As in years past, the conference offered a wide spectrum of presentations-nearly 100 papers in 26 sessions-ranging from commodity forecasts to the latest technical achievements. New Administration Stockpile Goals The minerals availability session included a presentation on management of the minerals stockpile by Paul K. Kruege r of the Federal Emergency Management Agency. Krueger notes that rather than providing incentives for development of a domestic raw materials industry, the government has "a history of providing disincentives to industry." In mining industries, he adds, the rate of productivity growth has been -6% over the last six or seven years. Krueger feels there will be a major change under the Reagan administration. In March 1981, FEMA began the first purchase program for the national defense stockpile in over 20 years. The stockpile is sadly out of balance, Krueger adds. Stockpile materials are

Jan 12, 1981

Seattle offered sunny, dry weather to about 2500 mining men who assembled September 10 to 14 for the 1961 American Mining Congress. The impact of snappy sessions on national mineral policy, state of the industry and foreign competition (to name only a few) was somewhat overshadowed by enthusiasm of conventioners for salmon fishing. This lordly fish, which mysteriously runs to its hatching place to spawn and die at this time of year, was not cooperating with the anglers in Puget Sound. However, this did not prevent consuming ample amounts of the deliciously prepared Quinault salmon at the "Potlatch" celebration.

Jan 10, 1961

Two sessions during the recent AMC Mining Convention in Los Angeles, September 23-26, served to update industry personnel on the status of health and safety regulations in the US. As reflected by the American Mining Congress resolution on mine safety and health, "Based on experience with the federal Coal Mine Health and Safety Act of 1969 and the federal Mine Safety and Health Act of 1977, (AMC) does not believe that laws designed to force compliance with regulations through the imposition of criminal or civil penalties will result in safer mines. (AMC) feels that the government's participation will be much more productive if greater emphasis is placed on research, training, and inspections aimed primarily at assisting operators and employees in recognizing and eliminating hazardous conditions and practices.

Jan 11, 1979

By Mark G. Colwell, Russell Frith

"An Analytical Model for Coal Mine Roof Reinforcement (AMCMRR) has been developed. AMCMRR utilizes a Factor of Safety (FOS) approach, which is commonly used in all forms of engineering. The starting point in the development of AMCMRR was an existing analytical roof behavior and roof support design methodology/model, originally developed by Colwell. This technique was used successfully in the Australian underground coal industry for roof support evaluation and design prior to and during the course of the research project, and when used, it was essentially calibrated on a site by site basis.It has long been recognized that bolts and longer tendons can modify the behavior and load bearing capacity of the reinforced roof via the concept of beam building. The break-through in developing AMCMRR was combining the original analytical model with a comprehensive database (associated with Australian collieries) to effectively quantify this reinforcing effect, and this in turn provided the ""platform"" by which this analytical model can be calibrated for the entire Australian underground coal industry.This paper focuses on the application and use of AMCMRR and the analyses undertaken to quantify the reinforcement beam building offers to the immediate roof. Furthermore, this paper demonstrates that a combined empirical and analytical approach is currently the most practical way of developing credible geotechnical design tools for the Australian or any other underground coal industry.BACKGROUNDBy the start of 2006 the ALTS (Analysis of Longwall Tailgate Serviceability-Colwell et al., 2003) and ADRS (Analysis and Design of Rib Support-Colwell, 2006) design methodologies were being routinely and widely used within the Australian underground coal industry. As a result of their success, Colwell Geotechnical Services commenced a research project entitled, ""The Future Development and Integration of ALTS & ADRS for Improved Underground Roadway Design. "" The project (which became known as the ALTS 2006 Project) was funded directly by several of the major coal producers as well as individual Australian collieries."

Jan 1, 2010

By Jorge Alberto Soares Tenório, Flávia Paulucci Cianga Silvas, Bianca Medeiros, Denise Crocce Romano Espinosa, Ivo André Homrich Schneider, Daniella Cardoso Buzzi, José Roberto de Oliveira

"AMD is one of the main problems associated with mining activities and the techniques used in their treatment may be the biosorption. The aim of this work was to study the rice husk as a biosorbent for the AMD treatment keeping constant: pH (2.6), biomass concentration (1g.L-1), temperature (25°C) and agitation (175rpm). And varying the contact time of 5, 20, 60 and 240 minutes. Rice husk samples will be characterized before and after the biosorptives tests through analysis of SEM and IR. The micrographs indicate the occurrence of micro-precipitation and changes in biomass physical structure. Since the infrared spectra indicate changes in functional groups present in the biomass before and after the biosorptives tests. AMD synthetic solutions will be analyzed by ICP in order to quantify the metals concentration captured by biomassIntroductionThe preoccupation for the environment has led the industry in general, to treat their waste. As the only industrial activity is increasing, the pollutants generated must undergo treatment processes aimed at reducing pollution, and therefore, less aggression ecosystems.In mining there is waste water with accumulation of heavy metals, and these are harmful to health of living beings, thus being one of those industries responsible for some pollution of the environment. These wastewater in contact with oxygen to generate an acidic water is called acid mine drainage (AMD). This aqueous solution has a pH below 3 and varieties of dissolved metals. When this solution comes in contact with water, generates a series of environmental problems, so there is a need to recover the metals present in the DAM."

Jan 1, 2012

"Decreasing gold-in-ore grades is one of the main drivers of poorer productivity and rapidly escalating unit costs. Grinding costs, water use and reagent consumption are all intimately related to the ore grade processed. Various pre-concentration technologies have been developed that can be applied at various stages of crushing prior to ore grinding. This paper will review the amenability of ores to coarse particle barren gangue rejection for fine crush sizes in the pumpable particle size range (i.e., particles between 5 mm and 0.3 mm in size). The liberation of oxide gangue achieved during crushing is evaluated by proxy using sink-float analysis and the deportments of gold, sulfur, and arsenic into sinks and floats are monitored. Amenability of gangue rejection by continuous gravity separation is evaluated after various crushing modes (vertical shaft impact crushing, cone crushing, and HPGR crushing). The potential to identify coarse particle mineral association and liberation using three-dimensional x-ray computed tomography will be discussed.INTRODUCTIONThe aim of research in this area is to explore some of the attributes which make some ores amenable to preconcentration, or rejection of a significant component of the feed mass to tailings at a coarse liberation size. Characteristics such as ore type, mineralogy, breakage pattern, particle shape, and liberation characteristics may need to be examined to identify amenability to pre-concentration amenability.It is intended to focus on continuous gangue rejection in the pumpable size range (0.3–5.0 mm) as this remains one of the key opportunities to reduce processing costs through a combination of techniques including screening (for mineral differentiation rather than size classification only) and gravity separation (using jigs). This is to be contrasted to conventional preconcentration as performed with automatic ore sorters."

Jan 1, 2016

By V. V. Lvov, L. S. Chitalov

"The purpose of the research is intensification of physico-mechanical ore properties determination for ball grinding processes in comminution circuits. The research presents comparative studies aimed at intensification of Bond Ball Mill Work Index (BWi) determination, such as testing technique of Ahmadi and Shahsavari, Berry and Bruse, Gharehgheshlagh, Horst and Bassarear, Kapur, Magdalinovich. The subject of the research is a test procedure of apatite-nepheline, copper-nickel, gold-sulfide and iron ores for the Bond ball mill index. The Bond Ball Mill Work Index for the material firstly was determined by standard Bond test methodology. Two the most promising testing techniques - Ahmadi and Kapur testing techniques - were modified. For the Ahmadi technique it was proposed to pay attention to the circulating load, which should be stabilized on the value of 250% as fast as possible. Two methods were put forward to quicker stabilize the circulating load. For the Kapur technique it was proposed to use empirical coefficients, which is determined especially for the apatite-nepheline, copper-nickel, gold-sulfide and ores. The modified Ahmadi and Kapur techniques require no more than two cycles of ball grinding to determine BWi (while normally 6-8 cycles are required) and less than 5 kg of initial feed. The suggested modified Ahmadi and Kapur techniques allow to intensify the physico-mechanical ore properties determination for ball grinding processes and BWi test costs considerably, which makes them useful for mass sampling and monitoring strength properties of ores entering a concentrating mill. INTRODUCTION When designing concentrating mills, the choice of the technological scheme for ore pretreatment, particularly the type, quantity and size of the main process environment, the determination of optimal grinding conditions and the calculation of equipment load are carried out by preliminary studies of grinding in semi-industrial or laboratory-scale plants. Semi-industrial tests on full-scale plants provide the most reliable information for calculating specific loads for equipment. However, this requires a significant amount of ore samples, a high labor costs and the pilot plants. Thence the most researchers performed grinding tests with small laboratory equipment using small ore samples."

Jan 1, 2018

By N. S. Keith

Some time ago, a firm engaged largely in the manufacture of copper sulphate, applied to me for information as to the practicability of obtaining the copper from their mother liquors by means of electricity ; having reference, more especially, to obtaining the electric current from some magneto-electric or dynamo-electric machine. The mother liquors were the result of several solutions of commercial scrap copper, containing impurities, the quantity of which

Jan 1, 1879

By A. L. Holley

The existence of iron ore and anthracite coal in the neighborhood of Providence, R. I., baa long been known, chiefly as a geological fact; that these materials, so near to each other and to tidewater, are of such a good quality and are present in such large quantity, as to have seriously raised the question of establishing blast furnaces there, was a surprising fact to me; and I have thought that the few notes I have lately gathered on the subject would be of interest at this partly New England meeting. The coal field referred to has an area of above 400 square miles, and is found throughout the belt of transition rocks extending from Newport Neck to Mansfield, Massachusetts. It underlies the cities of Providence and Newport, and the towns of Middletown, Portsmouth, Jamestown, Warwick, Barrington, Cranston, North Provi-

Jan 1, 1879

By W. S. Keyes

The State of Nevada, known par excellence as " the Silver State," occupies the major portion of the wide plateau, or so-called Great Basin, lying between the Sierra Nevada range on the west and the Wahsatch range of the Rocky Mountains on the east. It extends from the 114th degree to the 120th degree of longitude, west of Greenwich. It is limited, on the north, by the 42d degree of latitude, and on the extreme south by the 35th degree of latitude. Its general shape is that of an irregular parallelogram, from which the lower or southwestern portion has been cut off by a diagonal southeasterly line; the missing portion forms a part of the State of California on the west. The Great Basin is made up of a succession of low hills, or minor mountain ranges, running very nearly north and south, with long valleys between them. All of these mountains are more or less metalliferous. On the westcrn rim, marking the eastern flank or foothills of the Sierra, we find granites, porphyries, and propylites. Here we note the great Comstock lode, with its free-milling gold and silver ores, and still further south the once prominent and the now reviving gold and silver-bearing districts of Esmeralda County, Nevada, and of Morro County, California. Next, at some distance to the east, we find the mining districts at and near Unionville, in Humboldt County. Still further to the east we find the Battle Mountain copper-silver district, north from the railroad, and southerly therefrom the Austin or Reese Ever, Belmont, and other districts. Still further east and north of the railroad, we find the Tuscarora, a new district of very

Jan 1, 1879

By Oswald J. Heinrich

During the last twenty years much has been done to investigate and define the Mesozoic formatibn of the United States along the Atlantic States, as well as in' the Territories. The investigations of Professors Hitchcock, Emmons, Hayden, H. D. Rogers, and those now in progress in connection with the geologicd surveys of Penn-

Jan 1, 1879