Search Documents

By Diankun Lu, Ganfeng Tu, Edouard Asselin, Feng Xie

A novel separation process for detoxifying cadmium-containing residues arising from zinc hydrometallurgical processes has been developed. An initial investigation indicated that a high concentration of zinc in the sulfate solution can be effectively separated from cadmium by solvent extraction with P204 (di(2-ethylhexly)phosphoric acid, D2EHPA). The mixture of sulfuric acid and ammonium citrate ((NH4)3C6H5O7) is thus used to extract metals from the residue at room temperature. Copper in the leachate is recovered by solvent extraction (SX) with LIX 973. Cobalt in the raffinate from the copper SX process is recovered by precipitation with a-nitroso-ß-naphthol. The results show that more than 50% of the copper and virtually all the zinc, cadmium and cobalt in the residue can be leached under the experimental conditions used here. Virtually all dissolved copper and cobalt can be recovered in the subsequent solvent extraction and precipitation processes. The presence of (NH4)3C6H5O7 could significantly facilitate the extraction of zinc by D2EHPA in the subsequent separation of zinc and cadmium. More than 97% of the dissolved zinc can be recovered through a two-stage counter current solvent extraction process. After separating copper, cobalt and zinc, cadmium can easily be recovered from the solution either by cementation with zinc powder or by electrowinning, while the purified solution can be recycled back to the leaching process.

Jan 1, 2014

By M. Rufli

Until not so long ago most ring geared mills were operated with fix speed motors only. By using the latest generation of medium voltage frequency converters, new possibilities have arisen to improve the grinding process. Beside all the direct and indirect advantages, several dedicated functions have now been implemented for ring geared grinding mills in the minerals industry. The sophisticated operational functions ensure a smooth, safe and reliable operation with minimum stress for the mechanical equipment and therefore utmost availability of the mill. Several papers have already been presented concerning the benefits of using this state of the art technology for mill drives. Now this paper is focusing on the experiences gained with this kind of sophisticated ring geared mill drive system rather than only show and explains the operational benefit of the different functions. Several measurements of different operating conditions, starting, frozen charge remover, controlled roll back, backlash, etc., made on an installed and commissioned 2 x 5 MW dual pinion ring geared mill drive system will be shown and discussed. The accuracy of the load sharing between the two 5 MW motors during starting, normal operation and stopping will be demonstrated using real measurements from an operating system. Finally the inherent features of these drive systems are briefly discussed.

Jan 1, 2011

By A Jäger, J L. Lett, J Rachocki and B Mobilio

The Newcrest Mining Limited Cadia East Panel Cave mines near Orange, New South Wales, Australia commenced production 1200 m below the surface in May 2014. Understanding the mine-wide impact caving had on excavation stability was a primary objective to ensure a safe working environment as production ramped up in the Panel Cave 1 operation and establishment activities were implemented in Panel Cave 2. The impact of cave interaction between Panel Cave 1 and Panel Cave 2 and establishing monitoring systems to assist mine planning and production as both caves joined is explained in this paper. Monitoring tools such as a microseismic system, open holes, HI-cells, extensometers, fibre optic sensing, cave markers, closure monitoring, underground observations and damage mapping were used to characterise the performance and position of the cave back. The data and observations collected were compared to predictions from numerical and empirical methods and used to calibrate the numerical models for forward prediction and to develop site empirical design tools. The results and methodology for monitoring deep high-output caves are the key discussion points in this paper.CITATION:Lett, J L, Jäger, A, Thornhill, T, Rachocki, J and Mobilio, B, 2016. Geotechnical challenges in cave monitoring – a modern approach, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 203–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R. N. Tempel, M. Lengke

Arsenic sulfide [orpiment, realgar, amorphous AsS and As2S3] oxidation rates were measured in mixed flow reactors at pH~2 and temperature of 25-30oC. The measured oxidation rates for arsenic sulfide solids by dissolved oxygen are in the range of 10-11 to 10-10 mole m-2 s-1 after being normalized to final surface area. The order of arsenic sulfide oxidation rates decreases at pH~2 from amorphous AsS > realgar > orpiment > amorphous As2S3. In comparison to pyrite, arsenic sulfide oxidation rates are approximately 1.5 to 15 times slower than pyrite oxidation rates at pH~2.

Jan 1, 2002

By W. R. Reed

The National Institute for Occupational Safety and Health (NIOSH) uses light-scattering dust monitors (nephelometers) in its research to develop dust controls to reduce respirable silica dust overexposures in miners. Recently, the model 1500-pDR, an active nephelometer, was introduced by Thermo Scientific. Testing was completed to ensure compatibility with the metal/nonmetal mine dust personal sampling unit (M/NMDPSU). Results of testing demonstrated that gravimetric concentrations measured from the 1500-pDR are comparable to the gravimetric concentrations measured using the M/NMDPSU, without need for correction, under commonly observed dust loading conditions.

Jan 1, 2012

By Carl Havemann

[PAPER PRESENTED AT THE 8thINTERNATIONAL CORROSION CONFERENCE HELD AT THE SA NATIONAL MUSEUM OF MILITARY HISTORY, SAXONWOLD JOHANNESBURG DURING 14-15 NOVEMBER, 2006.]

Jan 1, 2006

By Bertrand L. Johnson

Barite, the natural sulfate of barium (BaSO4), is the most important barium mineral. Normally it is white (opaque to translucent), but impurities sometimes render it yellow, gray, blue, brown, red, or black. Brown or red stains are commonly caused by iron oxide. Barite is unusually heavy (specific gravity, about 4.5); in fact, it is one of the heaviest of the nonmetallic minerals. It is brittle and fractures unevenly. The hardness of barite ranges from 2.5 to 3 but is usually about 3. It can be scratched by a copper coin. Pure barite contains 65.7 percent BaO and A.3 percent S03. Much of the crude barite ore mined, however, contains impurities; thus it has a lower content of barite and consequently less barium oxide. Commercial analyses show its total BaSO4 content. Barium also occurs in nature as the mineral witherite (BaCO3), which, however, is not common in the United States, and commercial deposits have been found only in California. Witherite is a yellowish-white, light-gray, or Kite mineral with a specific gravity of about 3, a hardness of 3 to 4, and an uneven to subconchoidal fracture.

Jan 1, 1941

By R. E. McIvor, Brian Cornish, J. A. Finch, Yue Tan, Claude Gagnon

Fred C. Bond is recognized throughout the mineral processing world as the father of comminution equipment applied science and engineering. The Bond Work Index became a universal standard, and is the most widely used measurement tool for comminution energy consumption. This biography is the story of his lifetime of study, work experiences, experimentation, analyses and findings. His numerous published writings are reviewed. His legacy is one of comminution process engineering that will be used in perpetuity.

Feb 1, 2024

By C. Kruger

Anglo American Platinum has adopted a strategy of best practice principles (BPP) for sampling, mass measurement, analysis, and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned. The design called for the high-grade material to be crushed to 95% passing 2 mm, and the design allowed for a single-cutter primary Vezin sampler taking increments from a gravity flowing stream at regular intervals while filling a tanker for pneumatic offload at the base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from the smelting complex and the input to the refineries. In addition, the design incorporated the functionality to collect increments in an ?interleaved? fashion from the Vezin sampler for internal precision checks. The metal accounting strategy for Anglo Platinum involves the ongoing measurement of all inputs, outputs, and stock levels for all operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February, across the smelters and refineries (at least the base metal refinery). In the accounting period immediately following the introduction of the new crushing and sampling facility, a trend was developing whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter showed an increase in physical stock compared to the theoretical stock (sender) and the base metal refinery showed an increase in theoretical stock against physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question, and it was confirmed through the physical stock measurement results that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream. This paper showcases parts of the process that took place to explain the poor accountabilities for the two sites. Previous results from the sampler ratification process (of the interleaved sampling design) were reanalysed, a physical inspection was carried out on the sampling system again, and the sampler performance was monitored (quality control parameters) for the period. From these investigations, it was found that airflows inside the Vezin introduced the sampling bias. A change in sampling protocol was introduced, as well as certain physical changes to the sampling equipment, to eliminate the airflow and thus the bias conditions significantly. The accounting period that followed the phased upgrading process showed that the accounting between the smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below 5% relative to theoretical stock). Keywords sampling, metal accounting, Vezin sampler, sampler bias.

Jan 1, 2014

By Ryan C. Stephan, Christopher Mark

"Some of the weakest roof in United States coal mines is found in the Illinois Basin. Historically, the Illinois Basin has also suffered from high rates of unplanned roof falls and rock fall injuries. During the past decade, however, roof fall and rock fall injury rates have fallen dramatically, and are now lower than the national average. Several technologies are responsible for the improvement. Roof screen was rarely used ten years ago, but a number of mines now use it on a regular basis to prevent rock falls and rock fall injuries. Other roof skin control fixtures and work practices have contributed as well.The reduction in roof falls is also directly attributed to enhanced intrinsic roof support. Stiffer primary bolting patterns have reduced the magnitude of roof spalling and roof sag. They have also helped create a more intact beam that is able to be suspended from longer cable bolts. Cable bolt design methodology has also contributed to this reduction in roof falls. Some early cable bolt applications were unsuccessful because they employed as few as two cable bolts per intersection. This paper describes a methodology for estimating rock loads for support design.ROOF FALL TRENDS IN THE ILLINOIS BASINAlthough the Illinois Basin has a long history of poor roof conditions and high rates of unplanned roof falls and rock fall injuries, recent data indicates a change in the trend. Roof fall rates are determined by dividing the total number of non-injury roof falls by the total number of hours worked underground. The data is considered for 200,000-man hours. While the Illinois Basin was once a coalfield experiencing roof falls at nearly twice the national average, it is now at or below the national rate. Figure 1 indicates the trend over the past 20 years. In 2008, the Illinois Basin mines experienced 5.06 roof falls every 200,000-man-hours, compared to only 0.75 in 2018.There has also been a significant reduction in the rate of rock fall injuries in the Illinois Basin coal mines, as shown in Figure 2. In 2008 there were 1.48 rock fall injuries every 200,000-man-hours, compared to only 0.43 in 2018.ILLINOIS BASIN COAL ROOF GEOLOGYThe roof rock in the Illinois Basin has been studied in the past to understand the primary causes of roof failures (Molinda et al., 2008; Thompson, 2010; Molinda and Mark, 2010). Rusnak and Mark (2000) evaluated 10,000 laboratory strength tests from 800 rock units and concluded that for shale, siltstone, and sandstone, the strength of the Illinois Basin variety was less than half that of the same rock types in Central Appalachia (Figure 3). A study of Coal Mine Roof Rating (CMRR) measurements in more than 200 US coal mines also found that weak roof was predominant in the Illinois Basin (Mark and Molinda, 2005)."

Jan 1, 2019

By M. Craig Miller

As the trend continues in the U. S. toward inceased capital investment in longwall mining equipment and wider panels. the risk also increases for gotential financial and production loses due to undetected geologic anomalies. This paper describes how RIM Sm (Radio Imaging Method) is utilized in conjunction with more traditional exploration and interpretive methods to delineate fluvial channels. displacement faults and poor roof conditions in a Southeastern Ohio coal mine

Jan 1, 1990

By C. Pelley, A. Piche

"The Canadian mining industry faces the prospects of a severe shortage of graduate mining engineers over the next decade. This arises from three factors: first, a growth in industrial activity; second, the average age of company engineering and management staff; and third, the reduced number of students in engineering faculties around the world. This paper aims to identify the critical factors underlying the trend of inadequate recruitment into higher education for mining and to examine means of alleviating the problem.This paper is based upon surveys of potential and current students and graduate mining engineers from four mining schools. An attempt is made to understand institutional and industrial images, career prospects and what is required to attract enough high-calibre young people into mining education over the next decade.IntroductionThe mining industry has started to experience a severe shortage of graduate mining engineers which is likely to persist and even worsen in the short- to medium-term.This arise s from three principal factors:1. a recent and strong growth in mining activity, which surpasses that experienced through the 70s, before the recent international industrial recession; .2. an increasingly older average age of mine engineering employees, at least in the industry's larger companies; and3. problems associated with maintaining adequate mining undergraduate recruitment levels ."

Jan 1, 1989

By Brian Gar Wingfield

"The introduction of the QuarryMan laser profile system in 1987, along with the development of the corresponding 3-D software, gave a qualified operator pertinent information about dimensions of quarry highwalls, pattern and hole loading design, stockpile profiles, etc . . . Attributes helpful for this endeavor included surveying, computer, and blasting knowledge. Since not all operators had theseskills, a simpler model, the QuarryAce, was designed to look a t highwall dimensions in 2-D view . Al though less sophisticated than the QuarryMan instrument and its software, it is simpler to instruct in its use and has the ability to determine burdens at different depth levels . An in-house user f r i e n d l y computer program was designed to utilize QuarryAce depth vs. burden data . This program was created to enable laser and computer novices to generate information useful to the everyday blaster."

Jan 1, 1992

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

The conclusions reached by den Tex after a study of the fabric of some rocks from Broken Hill have been used to support the epigenetic hypothesis for the origin of the ore, first by Edwards (1959, p. 70) and then by Stillwell (1962, p. 131) in his criticism of Segnit's (1961) views. Den Tex claimed that the petrofabric study provided "independent evidence that the ore, at least in its present form, post-dates all events of a diastrophic nature in the area concerned".Repetition of this claim by Edwards and by Stillwell and the lack of any criticism of den Tex's work for more than three years implies its general acceptance by geologists in Australia. Therefore it appears necessary to examine parts of den Tex's paper in detail to show that his, conclusions are unwarranted. The major weaknesses in his study are that1. the petrofabric study was inadequate to warrant any major conclusions, and2. the petrofabric data allow alternative conclusions.Den Tex made a single visit to the field, collected six carefully selected specimens and presented quartz and· biotitepetrofabric diagrams for two specimens, quartz-diagrams alone for three more and included three diagrams of the orientation of c-axes and fractures in one specimen. It is not reasonable to come to firm conclusions about the origin of such a complex area as Broken Hill on such inadequate data, despite den Tex's claim (p. 87, lines 22 and 23) that "a thorough investigation of the quartz-fabric of the wall rock was undertaken".Den Tex's interpretation of each diagram is open to criticism, and alternative (and to my mind, preferable) interpretations may be made. It is impossible to evaluate den...

Jan 1, 1962

By Colin Lawrence, Michael S. Schultz

Due to the planned deepening of the NY Harbor, NYCEDC/NYCDEP is planning to replace two existing water lines between Brooklyn and Staten Island with one deeper water pipe. The crossing, just north of the Verrazanno Bridge is 1.75 miles long. The new pipeline will be tunneled using gasketed concreted segmented liners. Apressurized face machine will be used through the soft ground. This will be the first subaqueous application using this technology in New York City. This paper discusses the planning, design and risk issues associated with the crossing and the challenging soil conditions that resulted in the decision to use a pressurized face machine.

Jan 1, 2007

By G. Thom, A. Kay, J. B. Hyde

"This paper will initially outline the specific types of copper castings used in blast furnace iron production. Tuyeres, tuyere coolers and stack cooling plates will be discussed in some depth, with particular reference to their dimensional configuration and purpose.Following this, the failure of such cooling members will be discussed, with special focus on tuyeres. Tuyeres are the most common casting which often requires replacement. Reasons for failure and its effect on operations will also be included.The latter sections of the paper will deal with the strict specifications demanded by ironmakers regarding copper castings. The justification for such rigid demands will be explained through the material presented earlier in the paper.IntroductionThe modern 5000-tpd blast furnace, worth millions, is a large capital investment to be sitting idle. Consequently, ironmakers strive to minimize the loss in iron production and revenue from furnace downtime. Two major causes of downtime are furnace relines and shutdowns to replace damaged tuyeresor tuyere coolers. Copper ancillaries are important items in the production of iron. They are consumable items, therefore they contribute to the campaign life or to the downtime in blast furnace production.Several combinations of lining and cooling systems have been used with varying degrees of success. Blast furnace refractories have evolved from ceramic to carbonaceous linings. The Russians and Japanese have successfully introduced stave-cooled furnaces that may have several forms, such as evaporative cooling. Stelco has two furnaces which use the Russian-designed cast iron system. However, this paper will be confined to the use of copper cast cooling members in a conventional internally cooled furnace.Figure 1 is a schematic cross section of the E blast furnace. The three major sections of a blast furnace-the stack, bosh and hearth-are identified. Further, the locations of the various copper members are indicated. This furnace produces an average of 5300 tons of hot metal per day."

Jan 1, 1982

Magnetic anomalies in the Southern Coalfields have been subdivided into two characteristic types. Each type is attributed to a separate cause, one being basement structure, and the other near-surface igneous intrusions.Detailed geological mapping of the area and the ability to sample throughout the coalmines greatly assisted in this subdivision.The Triassic sequence contributes no magnetic effect of its own except to diminish the effect of sources within the underlying formations by raising the level of observation.Detecting the presence of igneous intrusions ahead of colliery working faces by magnetic observations within the coal mines may be of value in preventing accidents caused by gas outbursts and in planning the workings so as to avoid loss of production time.

Jan 1, 1967

By M. C. Villeneuve

A numerical modelling approach was developed to explicitly simulate geomechanical characteristics of intact rock: mineralogy, grain size and fabric. The approach involved creating a representative constitutive model for each of three common rock-forming minerals: mica, quartz and feldspar. The constitutive models developed are valid within the low confinement realm of excavation boundaries, where tensile fracture processes dominate. The mineral types were assigned to numerical elements, which were associated with each other through an algorithm created in a finite difference model, FLAC 2D (Itasca 2007a), to simulate real crystal geometries and orientations. The numerical models were used in a parametric investigation of the geomechanical characteristics and compared with published observations of the rock yielding process in laboratory testing. This approach has allowed the explicit grain-scale investigation of the impact of geomechanical characteristics on rock yielding at low confinement, leading to an improved mechanistic understanding of excavation-scale rock yielding processes at excavation boundaries.

May 1, 2009

By Glenn Lyle

CEMI Introduction ? Introduction of the CAF VOD Project ? Who are our partners ? What were the Outcomes What is next

May 1, 2011