Search Documents

By Daniel Tao, Jike Qiao, Hao Ren, Feifei Ji, Gonglun Chen

The floatation of niobite was studied using a number of collectors at various dosages and solution pH’s. Octyl diphosphonic acid was found to be an effective collector for niobite flotation with good selectivity. A flotation recovery of 91.2% was obtained with 140 mg/l octyl diphosphonic acid at pH’s less than 5.0. Infrared absorption spectroscopy (IAS) and X-ray photoelectron spectroscopy (XPS) were used to characterize the interactions of niobite with octyl diphosphonic acid. Species distribution diagram of octyl diphosphonic acid and niobium species was used to elucidate the flotation behavior of the mineral with octyl diphosphonic acid. A chemical adsorption mechanism of niobite with octyl diphosphonic acid was proposed. Keywords: octyl diphosphonic acid, electrokinetic measurements, niobite flotation, XPS.

Jan 1, 2005

By S. Kwon

When an underground excavation is created near to an instrumented measuring location, deformation at the location increases. The characteristics of this deformation increase, as well as the duration of the influence caused by the adjacent excavation, is dependent on parameters such as opening geometry and measuring location. In this study, neural networks were applied to investigate the deformation increase and the influence of each parameter on the deformation change derived from extensometer measurements at the Waste Isolation Pilot Plant (WIPP) site in New Mexico, USA.

Jan 1, 1998

By G J. Fleming

The Miwah prospect lies on the dilational 070¦ trending Miwah Lineament near its intersection with northerly oriented fractures within Pliocene volcanic rocks exposed between a NW trending segment of the dextral transcurrent Sumatra Fault, and the more northerly trending Samalanga-Sipopok Fault to the east. These faults reflect the continued interaction between stresses from the India-Australia plate located to the southwest, and spreading within theAndaman Sea to the north of Sumatra. A system of deep seated faults is believed to have facilitated emplacement of post-Miocene magmas and Quaternary volcanic centres at shallow crustal levels throughout northern Sumatra. Miwah mineralisation is associated with variably dipping structurally and lithologically controlled argillic and advanced argillic alteration. An oxidised supergene leached zone and a recent, thin, unaltered tuff blanket partly overlie the mineralisation. Mineralised zones are commonly brecciated and veined, and display quartz, quartz-alunite, quartz-alunite¦pyrophyllite¦kaolinite replacement assemblages, surrounded by more weakly mineralised, often vugghy quartzalunite¦pyrophyllite¦kaolinite advanced argillic, and argillic zones of quartz-kaolinite, quartz¦pyrophyllite¦kaolinite and smectite-illite-quartz. Propylitic assemblages are marginal to more intensely altered zones. Hypogene copper mineralisation is typified by enargite, luzonite, and covellite. The host mineral to gold is uncertain at present. Rare barite, native sulfur, and ?telluride also occur. Bornite and chalcopyrite have been observed in transported altered rocks in faults. Generally the mineralisation is anomalous in precious metals, locally enriched in Cu, erratic in Pb, and depleted in Zn, with a good correlation between Cu-As-Ag.

Jan 1, 1995

By B. M. Loftus

An investigation into the use of impinging stream (jet) reactors for the leaching of a free milling ore produced an increase in gold recovery by 10% while decreasing leaching time by up to 90%.Tests on refractory ores demonstrate no apparent improvement in recovery. However, leaching kinetics are dramatically increased when these ores are subjected to jet reaction prior to agitation.

Jan 1, 1997

Prefeasibility planning and cost estimation of conveyor systems has historically been undertaken by comparing fixed plant transport requirements to that of similar systems in service. This paper describes the development of a prefeasibility conveyor technical design and cost estimation application using Microsoft Excel Visual Basic for Applications (VBA) platform. The application tool known as D-Convey (Dachshund Convey) was developed with the goal enabling the end user:- to develop a technical model for conceptualised conveyor systems,- to perform economic analysis on the developed technical model, and - to conduct a comparative and risk analysis.An Excel VBA based platform was utilised to draw upon both the analytical and graphical capabilities of a spreadsheet. Some of the features of D-Convey system include a revolutionary dynamic graphical help system, known as the 'information pane' in lieu of traditional help files as well as the use of familiar graphical user interface elements such as the MS Office 2007 task ribbon. The D-Convey system incorporates material database allowing for mass handling prefeasibility estimation in other industries; it has been validated at a local quarry.

Dec 6, 2010

By Mohamad Hussein

Low strain dynamic tests are performed to evaluate the structural integrity of driven or cast-in-place concrete piles. This type of testing requires minimal pile preparation, and is simply performed by attaching an accelerometer to the pile head and striking the pile head with a hand held hammer. The measured data is processed by a dedicated system, inspected for wave reflections, and interpreted based on one dimensional wave propagation theory. Piles are normally tested shortly after installation so that problems can be identified early and corrective measures taken before construction of the superstructure. However, evaluation of existing foundations is occasionally required. Often, pile installation records are not available rendering impossible any rational foundation reanalysis. This paper discusses three case histories where low strain dynamic measurements allowed determination of pile lengths and structural integrity under existing structures where pile heads were not accessible.

Jan 1, 1992

By John J. S. Sebastian

A laboratory-scale investigation was made of the basic problems involved in developing a ceramic heat exchanger to operate at high temperatures for using nuclear heat from gas-cooled process-heat reactors. Technical data were obtained on transferring heat by forced-convection from helium to air in a single-tube vitreous-alumina heat exchanger. Coolant air was passed through the annulus parallel with, and either concurrently or counter to, the flow of helium inside the tube. The data obtained pertain to removing heat from the helium. Average inside film coefficients were determined at mean surface temperatures of 200° to 1,570° F., inlet-gas temperatures of 1,450° to 2,665° F., and Reynolds numbers up to 560. The gas-to-surface temperature ratios were varied from 1.05 to 7.6. The tabulated results are shown in the appendix at the end of this report. The film coefficients of heat transfer were correlated by taking into account the physical properties of the helium at the average fluid temperature. With experimental conditions pointing to a laminar flow, the Nusselt number was found to decrease as the ratio of gas-to-wall temperature was increased to a value of 3. However, within the range tested, gas-to-wall temperature ratios above 3 did not affect the Nusselt number, regardless of the value of the Graetz number. Thus, beyond this point any increase in this ratio ceased to influence the heat-transfer relationship.

Jan 1, 1962

By M. C. Mound, E. Gallestey, C. Colbert

Continuous operating performance and high profit is one of the major concerns in the mining industry. Information systems are expected to reinforce and enable conformance to these requirements. The companion efforts of business management and production information systems press for tighter integration to avoid over-laps, multiple instances of similar data, and expensive maintenance of databases. Implementation of advanced intelligent systems throughout a mine operation can reduce costs, optimize investment and create a shorter payback via conversion of the data accumulated by field and process devices into information, and subsequently, into decisions. However, in order to harness the potential power inherent in these intelligent devices, adequate and flexible modular knowledge-based solutions are required. Fortunately, there has been at least one such practical response to this challenge, namely the ABB IndustrialIT portfolio. With these tools in place, production efficiency is reached via integration of process, production, and quality information. Moreover, they permit immediate detection and remedial action to changes to process and boundary condition variables. Finally, using advanced optimization techniques supported by dedicated mathematical models, they allow for economic process optimization (process set points and coordination thereof, energy management, production planning, energy supply contract optimization, etc) of the plant as a whole.

Jan 1, 2004

Zircon producers are often required to lower impurity levels to meet customer specifications as most of these impurities adversely effect the end use. For example, zircon sand in foundry applications needs to be free of any surface impurities (eg clay, gibbsite and goethite) which otherwise could cause sintering or fusion between cast metal and the zircon mould. Light coloured ceramic grade zircon, typically low in iron oxides and titania, is preferred in ceramics applications. The presence of impurities in zircon sands is a problem in the magnetic and electrostatic separation stages of their concentration. Previous work (Aral et al, 1997) showed that impurities in zircon sand concentrates occurred in the form of stains on grain surfaces, discrete gangue minerals and in the mineral grains. The gangue minerals such as rutile, garnet, xenotime, monazite, spinels, ilmenite, and aluminium silicates in the concentrate in some cases (Aral et al, 1997) contribute significantly to the impurity content of the concentrate. A careful hand picking of the impurity grains from a Western Australian zircon sand showed that the impurity content of the concentrate could be lowered significantly as a result of the removal of the surface stained grains and gangue minerals. The hand-picked ædirtyÆ fraction, comprised about eight per cent by weight of the concentrate, and consisted mostly of iron-oxide/hydroxide-stained zircon, silica grains and rutile, and occasionally ilmenite, monazite, gahnite and other (unidentified) coloured grains. The chemical analysis of the remaining æcleanÆ fraction showed that the major impurities (Fe and Ti) were reduced significantly (Table 1). The reduction in the uranium content was about 30 per cent. The other measured impurities, P, Mg, Al, Th, and Ca remained mostly unchanged as shown in Table 1. The contribution of ilmenite to the overall iron content of æcleanÆ zircon was insignificant as it comprised about 0.1 per cent weight of the æcleanÆ zircon. Rutile was the major source of titanium contamination (about one per cent by weight). Recent work (Aral and Calle, 1999) on zircon sand concentrates from the Murray Basin showed that, under the electron microprobe, the bulk of the impurities occurred in the dark back scattered electron (BSE) regions of the zoned zircon grains. The impurity contents of the light BSE regions and unblemished (unzoned) grains were low. The impurity content in zoned zircons has been investigated on single, relatively large, crystals (McLaren, Gerald and Williams, 1994; Smith et al, 1991; Romans, Brown and White, 1975). These studies generally aimed to investigate the incorporation of U in zircon as zircon is used extensively for U-Pb geochronology owing to its relatively high content of uranium. Smith et al (1991) identified a striking difference in composition between the areas of lower (dark BSE) and higher (light BSE) average atomic number in the zoned zircon. Their work showed in particular that the zones of lower atomic numbers contained very significant amounts of trace metals such as Y, REE, Nb, U, Al, Fe, Ca, Ba and, by difference H2O. In this paper the impurity distribution in zoned zircon grains was investigated on statistically significant number of grains before and after a leach treatment. The distribution of impurities was also measured in unblemished areas to compare the results.

Jan 1, 2000

By J. W. MacDonald

Review of equipment, performance, and shaft design plans including head-frames for sinking and forms for lining are given. Also included are comparative data for shafts of 11 x20 ft and 193/4 x 30 ft with 756 and 666-ft depths, respectively. Advantage from curtain wall installation with "slip forms" which warrant consideration for normal lining are outlined. A preliminary review is also made of "chemical grouting" to stop water inflow leakage with Halliburton equipment and service. Two coal mine shafts recently completed in Franklin County, Ill., afford experience and accomplishment to warrant review. These shafts provide access to a tract with a potential recovery of one hundred million tons. This work provided the initial sinking by other than a contractor's organization since 1918. Four additional shafts required during the interim were sunk under contract arrangement with others. Supervisory contact and inspection afforded experience to govern planning and conduct of the recent work. TEST DRILLING Core test holes were drilled within each of the two shaft locations. Four additional cable tool holes were drilled on a radius of 700 ft from the shaft bottom to determine the coal seam elevations and govern the underground layout plans for each shaft. A graphic log of the hoist shaft test drillhole is shown by Fig. 1. A very soft sandstone was found at a depth of 16 ft. Cored recovery of the sandstone proved much weaker than the overlying compacted sand secured with coring facilities for soil recovery. Gradation from the very soft sandstone to fairly hard material occurred with the next 14 ft, extending to a depth of 30 ft. The weak character within the upper portion entailed need of adequate protection when sinking as described later. A part of the sandstone provided sufficient porosity and permeability to warrant further investigation. Adjacent cable tool drilling for temporary water supply disclosed inflow was limited to 2 gpm with a depth of 40 ft. It was increased to 12 gpm during the next 50 ft of drilling and occasioned subsequent precaution when sinking. General arrangement of facilities for sinking the hoist shaft is shown by Fig. 2. An available steel frame building was used to accommodate the hoist, compressor, shop, and shower or change room. The stiff leg derrick with 90-ft length of boom permitted removal of forms from the wood shop to the storage area or delivery within the shaft. Reinforcing steel and other needs were similarly handled, in addition to headframe erection. The headframe was placed over one end of the shaft to enable passage of forms for lining through the adjacent half next to the stiff leg derrick. The steel headframe as shown by Fig. 3 was fabricated locally. Side anchored cables from the

Jan 1, 1961

Productivity in underground metal and nonmetal mines is contingent upon work methods, mine layout, and ore handling techniques. One of the most important factors impacting productivity is the efficient movement of men, materials and supplies from the surface into and throughout the mine. Various transportation systems such as man-trains, service shafts, rubber-tired diesel equipment, etc. are currently used to transport men and supplies in underground mines. In many underground mines, it is not uncommon for a worker to spend 25% of his eight-hour working day traveling from the surface to his work area and returning to the surface.

Jan 1, 1975

Geophysical methods are useful non-invasive means of collecting subsurface information on the environmental impacts of resource developments. Techniques such as seismic refraction, ground probing radar and magnetics are well established tools for environmental studies of waste disposal sites. Repeat resistivity surveys, gravity surveys, and infrared or multispectral remote sensing hold great promise for monitoring environmental changes. Examples from New Zealand include geothermal field monitoring, which may involve the use of geophysics for .detecting changes of surface thermal activity, hydrothermal eruptions, induced earthquakes, contamination or depletion of shallow groundwater, and subsurface fluid recharge. Other examples include resistivity monitoring of contained effluent disposal ponds, tailings dams and landfills. Experience has shown that care is necessary to identify the natural variability of the parameter measured before drawing conclusions regarding an observed change.

Jan 1, 1994

Igneous phosphate deposits located in tropical and subtropical regions of the world are characterised by low P2O5 grades, very diversified mineralogy and intensive lateral plus vertical variations in chemical composition, mineralogical assembly, rock texture, grain size, slimes content and morphology plus surface coating of apatite particles. Those variations characterise ore types with distinct behaviour in mineral processing plants. This work reviews the main challenges to concentrate those ores, addressing developed solutions. Apatite concentration requires long chain anionic collectors to conduct reverse flotation of barite (alkyl sulfate) before direct flotation of apatite (sarcosinate, sulfosuccinate and oleate) at basic medium. The long chain collectors decrease the surface tension of the flotation solution (?LV) and a particular value of 51 mN/m was found to promote the most selective separation between apatite/gangue at a particular plant. Effective control of the magnitude of ?LV in industrial plants has not been realistic because there is a lack of reliable instruments to carry out in-situ measurements. Regarding gangue depression by starch, a review is made on possible mechanisms that promote its remarkable ability to depress some minerals (Fe-oxides, ortho plus meta silicates and calcite) vis-a-vis others (quartz, apatite and layered silicates). Flotation recovery (R) of fine (20<R<30 per cent) and coarse (30<R<60 per cent) apatite particles is considerably lower than the recovery of the intermediate ones (R>70 per cent) and inadequate hydrodynamic conditions within flotation cells are the main reasons for that behavior. Once the best hydrodynamic conditions to float coarse particles are not the same to float the fine ones, flotation of coarse and fine particles is commonly conducted at separated circuits in industrial scale. Entrainment of very fine gangue particles is an important source of contamination of apatite concentrates, mainly when weathered ores are treated. In most cases, adjustments in flotation equipment (columns or mechanical cells) promote considerable improvement in the quality of final concentrates.

Sep 13, 2010

By L. S. Urbanoski

This presentation describes a major modernization project at the Geco concentrator. The objectives of the program were to replace obsolete flotation equipment and upgrade process controls.Noranda Minerals Inc. — Gecc Division is located at Manitouwadge in Northern Ontario. The community is situated north of Lake Superior approximately equidistant from Thunder Bay and Sault Ste. Marie.Milling operations began in September, 1957. The mill processes a complex base metal ore by differential flotation techniques to produce copper, lead and zinc concentrates. To date some 43 million tons have been milled, qualifying Geco as a rather major base metal deposit.II. BACKGROUND:The Geco concentrator was designed and constructed in the mid 50's. A number of features specific to a concentrator of that vintage provided the justification for the modernization efforts described herein.Firstly, the mill was constructed without any instrumentation, not even pneumatic controls. Solid state electronics, computers and related instrumentation were unheard of, or rather primitive by today's standards.Secondly, some of the major equipment, in particular the flotation equipment, did not compare favourably to that in use today. MacIntosh flotation machines (more commonly known as Mac cells) were installed at Geco. These cells were prevalent in a number of concentrators built by Noranda, including Quemont Mining Corporation Limited, Gaspe Copper Mines Limited and Noranda — Horne Division. The Mac cells were used for copper and zinc rougher and scavenger operations. Some units were also installed for a pyrite recovery circuit that was never operated. In total, 104 Mac cells were installed in the main flotation area of the concentrator.

Jan 1, 1987

By W. P. Yant

A previous report of the Bureau of Mines dealt with the toxicity of dichlorodifluoromethane5, a new refrigerant that has a remarkably low toxicity. Continued research by the Prigidaire Corporation6 and toxicological experiments performed in the Laboratory of Applied Physiology of the University of Cincinnati7 revealed another organic fluoride, dichlorotetrafluoroethane, whose toxicity also appeared to be of a very low order and whose physical-and chemical properties make it suitable for refrigeration purposes. In addition to low toxicity, safety in its use is further enhanced by its physical properties, which permit the design of equipment that operates at comparatively low pressures and hence mitigates the dangers and problems of leakage. The investigation described in this report was performed by the Bureau of Mines at the request and with the cooperation of the Frigidaire Corporation.

Jan 1, 1932

By Andrew G. Martin

In 1991, Modular Mining Systems began marketing a Slope Monitoring System (SMS) now installed at twelve mines. The SMS uses automated wire line extensometers to monitor field conditions frequently. Every few minutes, the slope displacement values and current temperature are transmitted to a central computer via a packet radio telemetry system. The desktop workstation receiving the data continuously provides updated displays of active slope monitors and generates audible and visual alarms if movement exceeds user specified thresholds. The computer system also generates numerous graphs and reports for quick analysis of slope stability. This work describes the functionality of the SMS, details improvements to the SMS hardware and software developed for several clients, outlines different installation techniques needed for wall rock and spoil monitoring, and interprets slope movement data using illustrations of stable and unstable conditions.

Jan 1, 1996

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988

By M. Dworzanowski

The beneficiation of fine iron ore will increase in importance in the future because most new iron ore resources will be in the form of lower grade ore deposits that will require liberation of iron ore minerals at finer sizes. Generally this fine iron ore will be beneficiated to produce a pelletizing concentrate with very strict chemical and physical specifications. In addition, because of the increasing demand for iron ore there are now more opportunities to produce by-product iron ore from mining operations producing other commodities. In the past the associated iron ore minerals would report to final tailings but now there is potential value to be realised from by-product revenue. These by-product iron ore opportunities are almost all centred on producing pelletizing concentrate. Currently pelletizing concentrates are produced mainly by various combinations of flotation and magnetic separation. The selection of the beneficiation route will depend on ore mineralogy and considerations around plant capacity and final concentrate quality. The main economic iron minerals are magnetic, haematite being paramagnetic and magnetite being ferromagnetic. This, therefore, means that magnetic separation can be applied, in principle, to all fine iron-ore beneficiation plants. While flotation has a considerable capacity advantage over magnetic separation, the real advantage of magnetic separation over flotation in fine iron-ore beneficiation is that treatment of -10 µm iron ore is possible-in flotation, the feed is deslimed at 10 µm and the -10 µm stream is considered to be final tailings, even though there is often a significant amount of contained iron ore. This paper describes a study around the recovery of fine magnetite in the form of a pelletizing concentrate. The study is based on an evaluation of an iron ore by-product opportunity from an iron oxide copper-gold (IOCG) deposit. Experiments were conducted to quantify the differences in magnetic separation performance with decrease in particle size treated. A mineralogical evaluation of all the test work products was undertaken to facilitate the interpretation of the test work results. These results were then used to propose an economically viable flowsheet for maximizing fine magnetite recovery using magnetic separation.

Jan 1, 2012

By A. George Stern

In the examination of bentonitic clay suspensions used for oil-well drilling fluids3/ (and for other purposes, such as a core binder for foundry sand) it is important to have comparative tests for evaluating them. A satisfactory clay for these and other purposes should 'rave the property of forming what is commonly called a "gel," but the measurement of this property has been a real problem. To date the solution has not been satisfactory, and some of the difficulties are considered in, this, paper, which describes a simple form of instrument (identified as an eykometer) for measuring the yield point under hydrostatic conditions of non-Newtonian clay suspensions, including those muds that are thixotropic. An oil-well drilling mud serves several functions, many of which depend on the "gel" characteristics of the mud. Among the more important functions are: (a) To plaster the sides of the hole to prevent caving of the walls; (b) to prevent the loss of the circulating fluid out of the hole by seepage; (c) to carry sand and cuttings out of the hole to the surface as they are formed by the rotary drill; and (d) when circulation of the fluid stops for shut-down or other unavoidable cause, to hold the cuttings in suspension by the setting up of the gel, thereby avoiding the difficulties that result when these cuttings are allowed to fall through the fluid and pack at the bottom of the hole.

Jan 1, 1940

The following paper describes the refining practice for the production of lead, silver and gold at the works of The Broken Hill Associated Smelters Pty. Ltd., Port Pirie, South Australia.The refinery is situated on the wharf frontage and is built parallel with it. The refinery occupies an area of approximately 3380 square yards. (Fig. 8)There are two buildings, one containing the softening and de-silverising sections, measuring 225 ft. x 57t ft., while the other building, which measures 225 ft. x 90 ft. covers the de-zincing, lead moulding, retorting, cupellation, and dore parting sections. (Fig. 1)The retorting, cupellation, and dore parting sections are completely isolated from the rest of the plant by strong small-mesh wire gratings welded to steel uprights. The dore parting plant and generator room are further isolated by a brick wall, built up to the roof. The two main buildings are steel structures, with outer walls and roof of "Robertson" corrugated sheeting; the side and end walls are open for some distance above the ground, and this, coupled with the high roof which is 50 ft. from ground level, ensures the free access of air and light. Conditions are such that operators work in a clear atmosphere.

Jan 1, 1937