Search Documents

An oxide ore heap (80,000 ton assaying 2 per cent copper) and a sulphide ore heap (300,000 ton assaying 1·7 per cent copper) are being leached in series in a closed circuit system. The ore is friable and weatherseasily giving severe percolation problems. These were eased by applying liquors at 235 gal/min to trenches 2 ft wide and 6 ft deep along the full length of the heaps.Cementation recovery was improved from 20 per cent to over 80 per cent by regular intermittent agitation of the iron using a back hoe unit.Liquor pH is controlled by acid addition, and iron content is controlled by a bleed-off set according to predictions made from a pH-Eh diagram drawn for the liquor components. These controls, together with acyclic wetting and draining procedure, have raised production from 6 ton/week to 10 tdn/week of 80 per cent copper.

Jan 1, 1968

By Dong-kil Lee

Field tests have been conducted to investigate the characteristics of flow and physical chemistry of acid mine drainage(AMD) in the Hwangji-Yuchang settling pond in south Korea. pH and ferrous concentration of AMD flowed in the settling pond is 6.79 and 25.5 mg/l, respectively. As a results, we found that the ferrous oxidation reacted strongly around the inlet of the pond and the distributions of physicochemical properties is depended on flow characteristics and ferrous oxidation rate of AMD.

May 1, 2011

By Bruce I. Thomas

Reconnaissance studies of beach sands along the eastern part of the Gulf of Alaska were conducted by the Bureau of Mines to determine if any of these coastal areas warranted investigations as possible sources of valuable minerals. Because of difficult access and limited transportation facilities only a minimum of sampling, surveying, and camping equipment is utilized to obtain spot samples from key areas as well as information indicating the location, size, and character of the deposits. Such data were obtained from beaches located along approximately 247 miles of the Gulf of Alaska coastline during parts of the 1957 and 1958 field seasons. A total of 201 3-inch-diameter auger holes, spaced roughly at 1 mile intervals, were bored by hand methods to depths ranging from 3 feet to 27 feet; also 33 shovel samples were collected from selected localities. Samples were reduced to a rough concentrate in the field by panning; the rough concentrates were shipped to the Bureau of Mines laboratory at Juneau for further concentration and for petrographic and chemical analyses. Particular attention was given to the heavy-mineral content of the concentrates, although the types and relative amounts of rock-forming minerals were also determined. The reconnaissance indicated that, generally, the valuable mineral content of the beach deposits was too low to be of further interest except in the vicinity of Yakutat and Lituya Bays where erratic but possibly significant concentrations of magnetite and/or ilmenite were found. At Yakutat, about 20 miles of beachline extending southeasterly from Ocean Cape, yielded samplas containing from 1 pound to over 300 pounds of iron and from a trace to over 100 pounds of titanium dioxide (TiO2) per cubic yard of beach material. However, the higher grade samples represented local concentrations of minor importance. The general tenor of the Yakutat beach, as indicated by the airthmetical average of 27 auger-hole samples, is about 35 pounds of iron and 20.5 pounds of titanium dioxide per cubic yard of beach material. Ilmenite is the predominant heavy mineral of the beach deposits in the vicinity of Lituya Bay, but it was found in concentrations only in limited areas near the

Jan 1, 1962

By M. Gous

Namakwa Sands is a heavy minerals mining and beneficiation business in the Anglo Base Metals Division, and operates along the West Coast of South Africa. The business encompasses mining, mineral concentration, separation, and smelting operations. The smelting process comprises the carbonaceous reduction of ilmenite to produce titania slag with a TiO2 content of 86%, and iron with a carbon content of 2.5%. The Namakwa Sands smelter, situated near the Saldanha Bay harbour, commenced smelting operations in 1994, when a 25 MW DC-arc furnace was commissioned. The smelting operations were expanded in 1999, with the commissioning of a second 35 MW DC-arc furnace. Despite the fact that ilmenite smelting poses a technical challenge in terms of the high temperatures required, the physical characteristics of the slag, the constraints placed on the feedstock, and the tight product specifications, Namakwa Sands has continually increased slag production since 1995. High furnace feed-on utilization and furnace stability, complemented by continuous improvement drives, will be thevehicle to drive performance in the short-term, with longer-term performance enhancements due to strategic process development. Keywords: Pyrometallurgy, Namakwa Sands, ilmenite, DC-arc furnace, titania slag, pig iron

Jan 1, 2006

By Jim Gunderson

Jan 1, 2004

By Walter W. Fisher

A study of copper cementation on iron was initiated to determine the effect that deposited copper has upon subsequent cementation. A microscopic investigation of cementation on an iron surface showed that cupric ion precipitates predominately on a growing copper deposit attached to the iron surface. A kinetic study of the cementation process in a revolving drum showed that the cementation rate is enhanced by the copper deposit attached to the iron surface and by the discrete copper particles of a cement copper slurry. The kinetic study also indicated that the character of the deposit is affected by the major anion in the solution. The cementation process is visualized to occur as a series of electrochemical cells in which cupric ion precipitates on copper dendrites attached to the iron surface.

Jan 1, 1973

By T. Bajpayee, L. Prosser, A. Iannacchione

Reducing the number of roof fall injuries is a goal of the NIOSH mine safety research program. Central to this effort is the development of assessment techniques that will help to identify the nature of the risks associated with working under potentially hazardous roof conditions. This paper discusses a method to determine the roof fall risk using a qualitative risk analysis technique. The ability to determine roof fall risk has been a long-standing goal of safety professionals and can provide the kind of information, needed by on-site personnel responsible for worker safety, to mitigate roof fall injuries.

Jan 1, 2007

By Jamal Rostami, Ataollah Rahbar

"Uma Oya Multipurpose Development Project is under construction in Sri Lanka. This project involves 2 Rolled Concrete Core (RCC) Dams connected through a tunnel currently under construction by Drill and Blast method. The water is transferred from first diversion dam to the 2nd regulatory dam and from which, it will be transferred through a 14 km headrace tunnel to the top of a 650 m deep drop shaft that feeds the high pressure water to an underground powerhouse and turbine chamber for generation of 120 MW of electricity. The Headrace and Tailrace tunnels are being excavated by two 4.4 m diameter double shield TBMs. The headrace tunnel has already passed 5km milestone and is mined in hard rock, while the tailrace tunnel has been completed in rather weak and fractured ground. This paper will review the history of the project along with the geology of the site. The operation of TBM in headrace tunnel will be discussed in more detail, focusing on the challenges of excavating through very strong and abrasive quartzite and gneiss on this site, as well as reaches of tunnel in high inflow of water reaching 400 L/Sec. INTRODUCTION This paper aims to introduce the Uma Oya Multipurpose Development Project (UOMDP) as a hydro mechanical project in Sri Lanka, targeted generating hydro-electric power, transferring water for irrigation purposes and controlling seasonal devastating flood. This project lies in the south-eastern part of the central highland region of Sri Lanka (Figure 1). The main part of the project is located in the south-western part of the Badulla district in the province of Uva. The south-eastern end of the project site is in the central west of the Moneragala district (province of Uva). Bandarawela is the largest urban setting within the project area, located halfway between the upstream and the downstream ends of the planned hydropower plant and combination of dams, tunnels, and downstream facilities. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya. The feeder (power) tunnel Lot consists of a headrace tunnel (L=15554m), the surge shaft (L=200m) and tank on the upstream of the vertical shaft, a vertical shaft with steel lining (L=650m), an underground powerhouse and a tailrace tunnel (L=3650m)."

Jan 1, 2016

We present a novel hybrid algorithm for quantifying the ore grade variability that has central importance in ore reserve estimation. The proposed algorithm has three stages: (1) fuzzy clustering, (2) similarity measure, and (3) grade estimation. The method first considers data clustering, and then uses the clustering information for quantifying the ore grades by means of a cumulative point semimadogram function. The method provides a measure of similarity and gives an indication of the regional heterogeneity. In addition, grade estimations can be obtained at different levels of similarity using a weighting function, which is the standard regional dependence function (SRDF). Keywords: Grade, fuzzy clustering, similarity measure, point madogram, weighting function.

Jan 1, 2008

By S. Makni, A. Faucher, F. Robichaud, A. Bouajila

"Optimizing the ball charge in a grinding mill may be needed to maximise throughput or alternatively, to achieve proper product size in more challenging situations. Efforts to optimise the ball charge however are essentially empirical and suffer from the lack of appropriate, accessible and reliable tools. To address these limitations, a new model-based technology was developed that relies on 3D Discrete Element Method and population balance techniques: it takes on the form of a simulator that aims to significantly decrease the time required to optimise the size distribution and the grinding media load within a ball mill. This paper summarizes the research work related to the development of this simulator. The calibration of the different constituting sub-models will be highlighted. The successful use of the simulator to predict the effect of ball make-up on the grinding product size distribution in one plant is also reported.INTRODUCTION Adjusting the characteristics of the grinding media charge in grinding mills holds significant potential for optimisation of mill performance. For example, properly adjusting the ball size distribution in a ball mill can help achieving specified targets for final product size distribution and/or throughput capacity. However, several problems appear when reviewing the process and the available tools to optimise ball mill load: • The current empirical simulation tools are lacking with regard to the ability to predict the performance of grinding when changes to mill ball make-up are made; • Generally, these tools estimate the top size of the charge so it is difficult to predict the effect of mixed ball make-up; • As the quality of prediction of these tools is low, the operators try to optimise the ball charge by a ""trial and error"" method and proceeding with conservative changes. The influence of these changes on grinding performance is often less than the measurement precision and the improvements then remain imperceptible; • A change in ball make-up may require an average of about 6 months waiting period before reaching the stationary state of mill ball load. This exercise is due to be costly if applied change decreases the mill performance. In its effort towards the comminution process optimisation, COREM R&D portfolio had addressed the herein described opportunity during the last five years This paper describes the technology already developed for the optimisation of ball charge. It takes on the form of a simulator that aims to predict the evolution of the grinding media load, the grinding energy available in the ball mill and the final product size distribution. The simulator was first validated in a pilot scale ball mill and then applied in an industrial case."

Jan 1, 2012

By W. W. Aljoe

The use of protective canopies can result in canopy roofing and/or serious restrictions to operator comfort and vision. To document this experience, BCR conducted a field study of cab and canopy design and application which resulted in a catalog of 164 canopy designs and an analysis of field data which showed no simple relationship between working height and canopy-related problems. The relationship also involves (1) machine frame height, (2) mine floor undulations, (3) operator compartment dimensions, (4) canopy design and location on the machine. Data analysis indicates (1) present technology does not always permit successful application of canopies in working heights below 42 inches, and (2) development of satisfactory low-coal canopies is doubtful. The basic conclusion of the study is that future R&D studies should be directed at development of alternative protection systems and remote mining methods.

Jan 1, 1981

Greymouth River Dredge û Birchfield Minerals Ltd Blackwater Gold Mine û Macraes Mining Company Ltd Globe Progress Gold Mine û Macraes Mining Company Ltd

Jan 1, 1996

By R. O. Suominen, P. A. Taskinen, K. R. Lilius, A. T. Jokilaakso

Chalcopyrite concentrate was flash-oxidised in a laminar-flow furnace in oxygen-nitrogen atmospheres that ranged in composition from N2 to N2 + 50 vol% O2. Gas pre-heating temperatures were 500-1100 degrees C and four particle-size fractions were studied: 28-38, 38-44, 44-62 and 62-74 micrometres. The effect of the residence time of the particles on sulphur removal was studied in the range 0.1-0.35 s. Scanning-electron microscopy combined with energy-dispersive analysis and back-scattered electron analysis was used to determine the morphology and mineralogy of the reacted particles. Total desulphurisation was achieved under the most oxidising conditions. Particles were observed to undergo fragmentation during oxidation, the violence of this depending on the iron and sulphur contents and the original particle-size fraction. The melting and/or reaction stages of the particles under different conditions were studied in powder samples. Polished sections were examined to follow the development of porosity and the mineralogy of the particles. A model for the fragmentation process is described

Jul 1, 1991

By JOHN G. RAYNER

An examination was made of the filtration characteristics of a haematite slurry using a range of polyacrylamide based flocculants in solutions containing up to 3 per cent sodium chloride. The polymers used were "high" and "Iow" molecular weight and had from 0 to 40 per cent charged groups.Increasing charge density tends to reduce the dose required to achieve optimum performance measured by filtration rate and by cake moisture. In general increased salt addition tends to increase the dosage required to achieve these optima. Both these observations result from the change in polymer extension and accord well with the bridging theory of flocculation.The dose required for optimal cake moisture is up to three times greater than that required for optimal filtration rate. This effect is reasonably consistent for all polymers studied and appears to be non-linearly dependent on salt concentration, with the difference being small at 0 and 3 per cent but quite significant at 1 per cent.

Jan 1, 1987

By Don Rose

INTRODUCTION A number of tunnels supported and permanently lined by steel-fiber-reinforced shotcrete (SFRS) have been built in North America in the 1980s. The material is more economical than, and technically equal or superior to, conventional shotcrete using wire mesh. The design and construction of SFRS-lined tunnels is straightforward, and only a few new design principles, laboratory tests or construction equipment modifications appear necessary in order to use this material. Modern tunnel Contractors may use cyclic drill-and-blast methods on some tunnels, with intermittent shotcreting as part of an orderly cycle. The Dry Mix method is most suitable for cyclic, intermittent, relatively small-scale shotcreting. However, modern Contractors excavating tunnels continuously using large long Tunnel Boring Machines (TBMs) or Roadheaders may prefer Wet Mix shotcreting on a mass production basis. In either case, the use of steel-fiber-rein¬forced shotcrete (SFRS) promotes the rapid and economical excavation of tunnels. The addition of microsilica will improve SFRS properties and reduce rebound, and is expected to become standard practice with SFRS in North America, as it now is in Scandinavia. HISTORICAL REVIEW Steel-fiber-reinforced shotcrete (SFRS) at the present time (1985) is essentially conventional shotcrete with straight or deformed steel fibers added, and in general SFRS for tunnel linings encounters the same problems that conventional shotcrete does. Shotcrete history is well known. The use of sprayed plaster on wire frames for mounting animal skins by Carl Akeley of the Smithsonian

Jan 1, 1985

By Manqiu Xu, Pete Winn, Steve Wilson

"In the flotation of ultramafic ores at Thompson mill, Inco Limited, CMC is used as both a floatable rock depressant and electrostatic serpentine slime dispersant. CMC, being a high molecular weight polymer, creates a serious handling problem in its introduction into the flotation processes. Typically, it is added as a 1-3% solution. This requires an enormous handling facility and makes its metallurgical gains uneconomical.Laboratory studies have shown that dry CMC addition as opposed to wet addition is feasible, as long as sufficient conditioning time is provided. Dry CMC addition into the grinding mill is also possible but its effectiveness is slightly reduced as compared to dry addition after grinding mills. Dry CMC addition using a vibratory feeder into the mill discharge is successfully applied in the treatment of ultramafic ores at Thompson mill.INTRODUCTIONManitoba Division MineralogyAt Inco’s Manitoba Division, two distinctly different sulphide ores are processed at the Thompson mill - primarily by froth flotation. The Thompson and Birchtree mines are both located within the Thompson Nickel belt. Sulphide mineralogy is relatively simple and includes both hexagonal and monoclinic pyrrhotite, pentlandite and minor chalcopyrite hosted in metasedimentary and metavolcanic rocks. The significant difference between the two mines is the amount of ultramafic rock associations in the host material. Increasingly, more of the ultramafic associated ores from the Birchtree mine are being processed through the mill with a characteristic poor metallurgy."

Jan 1, 2000

By Joseph M. McCann

The Brightwater regional wastewater treatment facility, under construction in King County, WA, includes an extensive conveyance system that will feature deep, soft-ground tunnels and shafts. Excavation of the Ballinger Way Receiving Portal to 65.8 m (216 ft) below grade through challenging geology was accomplished by means of artificial ground freezing. This paper discusses freeze design development, system installation and monitoring, and the contractual and construction challenges that were overcome, including work sequencing and excavation means and methods, together with lessons learned.

By R. O. Williams

A recent article by Chernock, Singer, Mueller, and Beck 1 which supports the use of the integral of I sin $ d$ for comparing fiber texture data does not settle what happens to I sin ø as ø approaches zero, where I is the diffraction intensity for poles oriented 0 deg from the fiber axis. They indicate that they believe that it should approach some constant value (that is, I increases without bound) and the fact that in reality it does not was a result of the diffraction

Jan 1, 1960

Phase I of U.S. Bureau of Mines contract H01220S3, "Improved Sensors and Fire Control Systems for Mining Equipment, II was an investigative effort involving study of the fire problem and preliminary design of a fire protection system. Overall contract objectives included three basic efforts: * Identify problems * Develop a design * Demonstrate a system The first two efforts were conducted during the period June through November, 1972. Phase II will involve testing of system components; construction and testing of a mockup; and demonstration of the system on a truck to prove its effectiveness under actual operational and environmental conditions.

Jan 1, 1972

By F. Dieu, C. Laughton

CERN, the European Laboratory for Particle Physics, is, at present, constructing an underground tunnel and cavern network to house a Large Electron Positron (LEP) colliding beam machine. This paper describes the techniques adopted to permit the excavation and temporary support of the access shafts through a series of glacial moraines, at depths of up to 80 m, to reach the bed-rock. Owing to the presence of superficial and deep water-tables, the variable nature of the moraine deposits and, above all, the tight work schedule, a combination of diaphragm walling and ground freezing was employed.

Jan 1, 1987