Search Documents

By M. Rossi

Geologic ore controls are usually interpreted and modeled from cross sections and plans, as they are critical to construct meaningful and accurate ore reserves models. The geologic boundaries are often modeled as two-dimensional surfaces or three-dimensional solids and used as hard boundaries to constrain the grade estimates. In many cases, the geologic model is the most important factor in estimating the mineralized tonnage predicted by the reserves model, since it is generally drawn to separate the volumes of mineralized and waste material within the deposit. Because geologic models are interpreted from widely spaced drill hole data, the accuracy of the contacts of the different zones modeled could be poor. The lack of accuracy in the definition of geo-logic zones can have a significant impact on a resource model. In this paper it is shown that the geologic interpretation can and should be checked for potential biases. In particular, an unbiased overall volume of the original drill hole information with respect to the resulting solids and codes assigned to the block model is sought. In addition, geostatistical conditional simulations can be used to simulate the geologic attributes modeled, thus providing an alternative view of the geology, and a measure of the uncertainty of the geologic boundaries. The simulated geologic model provides an assessment of the impact of alternative geologic interpretations on the over-all uncertainty of the reserves model. In the case study presented here, the uncertainty of the geologic model is quantified for a difficult-to-model, high-grade copper deposit in northern Chile.

Jan 1, 2004

By L. A. Neumeier

The Bureau of Mines evaluated the properties of zinc alloys containing 25 to 40 wt pet Al and 0 to 0.7 pet Mg. Microstructures, hardness, and tensile properties were evaluated for material as extruded at 285° C, solution treated at 300° to 400° C, and subsequently aged at 100° to 200° C. The alloys without magnesium are characterized by low hardness and strength with high tensile elongation and reduction in area. It was verified that magnesium effectively retards the Zn-Al eutectoid transformation below 275° C and markedly increases hardness and strength with decreases in ductility. Solution treating at 350° C results in large grain sizes and gross embrittlement. Subsequent aging of the Zn-Al-Mg alloys at 200° C restores ductility substantially and stabilizes the structures, but strengths are considerably reduced. Combined strength and ductility properties are better for the as-extruded condition than for any heat-treated condition. There is usually little advantage in overall tensile properties from increasing magnesium above 0.1 pct.

Jan 1, 1971

By R. M. Jara

This work evaluates and characterizes the impact of the support size and mining dilution of a block model in the operation and selection of equipment at an open pit mine. An exploratory analysis and geostatistical modelling of the grades assayed on a set of drill hole samples is performed, which allows constructing a grade model on a dense grid by means of a conditional simulation. The grades are then averaged to greater selective mining unit supports in order to proceed with the study and methodology. First, the metal-tonnage curves are used to analyse the loss of selectivity on the in situ resources caused by a change of support. Concerning the ore reserves and their mining sequence, defined in the pit optimization and analysis process, the same curves prove that the loss of selectivity is more accentuated. Second, the importance of the block boundary dilution produced during mining operations is assessed. Its value depends on the amount of ore in contact with waste, on the loading error of the equipment and on the ore loss/waste dilution criterion assumed by the planner. The dilution percentage and the differences between waste and ore grades become higher when the block size decreases. For these reasons, considering the dilution in the production plans makes mining a small support more constraining. An adequate delimitation of the orebody can improve the mining selectivity, leading to greater income. Finally, a study of the increase in mining cost that provides a zero difference in NPV between the different block size options is carried out, in order to determine the maximum increase in mining costs for which it remains profitable to mine at a smaller block size. Keywords: Mining selectivity, support effect, block boundary dilution, selective mining unit size, block model.

Jan 1, 2006

By Pierre De Pasquale, Aquilino Antonio Alvarez-Castro

Greenhouse gas emissions are now an essential issue for extractive industries. Actually, lowering of quarry energy consumption and CO2 emissions participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry.

Jan 1, 2016

By Nathaniel Arbiter

In contrast to pyrometallurgy's 6000year history in metals production, hydrometallurgy is of relatively recent origin. The earliest reference to it was in the 16th century, with the first applications to copper in the 17th and 18th centuries. In the 19th century, increased demands for pure metal resulted in the development of electrolytic refining, and early in this century electrowinning. The rapid growth in copper production in the 20th century, particularly in the United States and Chile, stimulated the development of new technology for leaching and for the recovery of copper from leach solutions. In the past 25 years, solvent extraction has become a major factor by permitting novel leaching technology that produces dilute or complex solutions. In addition, solvents other than sulfuric acid, and chemical methods for precipitating copper metal are now of increasing interest. These are trends that should grow in importance with the need to process lower grade and more complex materials. The evolution of copper hydrometallurgy is reviewed. Key factors in recent major developments are presented with details of specific operations and with trends for the future indicated. The relative importance of copper hydrometallurgy is compared with that of pyrometallurgy in the light of probable changes in ore supplies and character.

Jan 1, 1994

By Gibbs R

The objective of this paper is to provide a broad qualitative perspective of the needs and costs of infrastructure associated with typical mining projects. Infrastructure may be defined as anything necessary for the development and operation of a project, which is peripheral to the basic extraction, handling and processing of material. As depicted in Figure 1, infrastructure acts as the link between the technological heart of a project and the outside world.

Jan 1, 1990

By R. Sharon, P. M. Hawley, X. Ochoa

"Development of Barrick Gold’s Pierina gold mine in north-central Peru requires construction of a waste dump for disposal of nonore grade materials stripped from the open pit to expose the ore. The waste dump site is located near the open pit in a U-shaped valley that is underlain by thin colluvial and morainal soils with locally thick peats and glaciolacustrine deposits. Bedrock underlying the site consists of variably weathered volcanics. The site is subject to moderately high seasonal rainfall and significant seismicity. The geotechnical quality of the waste rock is highly variable, ranging from low-quality, degradable, soil-like materials containing appreciable quantities of silt and clay, to high-quality, hard, durable, blocky waste rock.A hybrid dump design concept was developed that requires in-pit segregation of highand low-quality waste, and selective placement of materials in the dump to maximize stability and enhance internal and subsurface drainage. The design includes a rock drain beneath the dump along the axis of the valley and a series of connected finger drains. Extensive peripheral diversions and stormwater control measures to inhibit infiltration of precipitation are also included.This paper discusses the unique challenges presented by the site and waste materials, the design methodology and stability analyses, and planned monitoring systems."

Jan 1, 2003

By A. Broussaud, J. D. McKay

Benefits analysis of adaptive Expert control systems operating at plants in Africa and the United States are presented. Proper statistical tools and techniques are discussed. Technical and practical pitfalls of strategy comparison are also presented and illustrated with from published data. Advantages and disadvantages of a “Pay for Performance” approach to a project are reviewed.

Jan 1, 2001

By Jean J. Abiassi

The Boston Marine Industrial Park (BMIP) VENT 6 project is a cut and cover tunnel, part of the Central Artery / Tunnel (CA/T) in the city of Boston. The BMIP job will serve as the south approach to the Third Harbor Tunnel crossing. The alignment is approximately 2500 Ft long and is made up of four sections starting from west to east: 1. West Tunnel 2. Boat Section 3. East Tunnel 4. Tunnel inside Vent 6 Cofferdam and connection to the Third Harbor Tunnel. The support of excavation (SOE) system for the West Tunnel, Boat Section, and East Tunnel are all a part of this project whereas the SOE for Tunnel inside the Vent 6 Cofferdam was a part of the contract for the Third Harbor Tunnel.

Jan 1, 1994

By Gregory R. Gorrell

The legal issues surrounding the regulation of subsidence are among the major concerns facing the underground mining industry today. Whether subsidence occurs almost immediately as a result of longwall mining or without warning as a result of room and pillar mining conducted years ago, the resulting disputes are highly controversial and typical of the disputes involving the competing interests of surface and mineral estate owners. Until recently, the law governing these disputes was firmly established under the common law. The passage of the Surface Mining Control and Reclamation Act 1, the utilization of new mining technologies, and the general heightened environmental awareness of our times, however, have interjected new issues into this area of the law. State and Federal court decisions and administrative agency interpretations have helped clarify some of the issues. However, as evidenced by the many recent lawsuits between operators, surface owners, and regulatory agencies, many uncertainties still exist.

Jan 1, 1986

The Mine Safety and Health Administration (MSHA) defines an independent contractor as any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine. Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Jan 1, 2008

By D. H. Desy

The Bureau of Mines has conducted research on the ignition of methane-air mixtures by sparks caused by frictional impact of aluminum alloys on rusted steel at typical coal mine fan speeds. The objectives were to establish the incendivity of aluminum alloys under these conditions, to investigate differences between aluminum alloys, and to evaluate substitute materials for the aluminum-steel combination. With a specially designed apparatus, three commercial aluminum casting alloys and a number of experimental aluminum alloys were tested for incendivity of the frictional impact against rusted steel in flammable methane-air mixtures. All aluminum alloys tested produced some ignitions. Of the experimental alloys, the harder alloys and those containing silicon tended to be more incendive than the others. With the normal experimental conditions, constructional steel, stainless steel, brass, and plastic did not cause ignition of methane-air mixtures in frictional impact against rusted steel. Some ignitions occurred with constructional steel at high speed in more flammable gas mixtures enriched with oxygen. From these findings, it is suggested that constructional material combinations other than the aluminum-steel combustion would minimize this inc endive hazard. A detailed description is given of previous research, and comparison is made with present results where appropriate.

Jan 1, 1975

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By H. Saroglou

The anisotropic behaviour of Athens Schist has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the Athens Schist were statistically analysed and evaluated.

Jan 1, 2004

By J. J. Forbes

The activities of the Bureau of Mines include the development and testing of self-contained oxygen breathing apparatus and other devices for respiratory protection, the development and tasting of devices for detecting dangerous or noxious mine atmospheres, and the training of men in the mineral industries in the use and care of this equipment to enable them to render effective service in mine rescue and recovery operations following mine fires and explosions, or under other conditions where irrespirable gases may be found in mines or mining plants. The first use of self-contained oxygen breathing apparatus for com- bating mine fires and explosions in the United States dates back about 30 years. Previous to that time, exploration for any distance ahead of fresh air was virtually impossible without great risk to life; moreover, the men called upon to render service at mine disasters were not well-versed in the properties and physiological effects of gases likely to be encountered. It was also impossible to work ahead of fresh air to restore ventilation, and if many stoppings were blown out by an explosion, air had to be introduced into whole areas or sections at once without knowledge of the conditions ahead; moving an explosive mixture of methane and air over live fire had to

Jan 1, 1938

Changes in reductant and energy inputs which are required to adjust the slag composition in an ilmenite smelter to a higher or lower FeO content are calculated. The calculated changes are based on the assumption that solidification equilibrium with the freeze lining constrains the slag composition to follow a eutectic groove in the TiO2-FeO-TiO1.5phase diagram. Calculated equilibrium conditions along the eutectic groove are presented, and form the basis of the calculations. The inputs of energy and carbon need to deviate strongly from the steady-state values to adjust the slag composition. The inputs required at any given time depend on the desired rate of change of the slag composition, and the current slag composition. The steady-state relationship of a change in energy input of 5 kWh corresponding to a 1 kg change in carbon input also holds for the changed inputs during transient changes in FeO content. Keywords: Ilmenite smelting, freeze lining, solidification, eutectic

Jan 1, 2003

By P Knight, P A. Walker, H E. Speight

Pushback 8 South is the final cut back on the south wall of the East Pit at BHPBilliton?s Mt Whaleback iron ore mine in the Pilbara region of Western Australia. Development of the cutback commenced in 1999 and is now nearing completion with ultimate pit walls up to 300m high. This paper describes the geotechnical, structural and hydrogeological setting of PB8S, reconciliation between design and slope performance and the slope engineering techniques used to effectively manage the risks associated with the slope. These techniques include slope buttressing and sequential mining with waste backfilling, as well as a detailed program of displacement and hydrogeological monitoring, structural mapping and slope stability assessment. During the course of slope formation recent developments in remote slope displacement monitoring using radar and remote structural mapping using terrestrial photogrammetry have also been applied. Aspects of the PB8S slope management plan are relevant to many large scale open pit slopes. This paper provides geotechnical practitioners with information which may be helpful in managing geotechnical risk in similar environments.

Jan 1, 2006

By Claude Bazin

"Laboratory semi-batch flotation tests were conducted using two different sulphide ore samples. The size reduction was adjusted to cover a wide range of flotation feed size distributions. Results show that similar recoveries can be achieved independently of the fineness of grind. This result suggests that possible energy savings could be achieved by a redistribution of the power between the grinding and regrinding mills. The behaviour of the selectivity curves shows that some gangue minerals are more sensitive to particle size than other ones, implying the existence of preferential associations between minerals in the ore.INTRODUCTIONInteractions between grinding and flotation have been studied for many years, and still a robust model to link the two processes lacks to be developed (Girard et al., 2005; Bazin et al., 2001). The ore size reduction liberates mineral grains, while flotation separates them into valuable minerals and gangue. The more size reduction that is applied to the ore the more important is the mineral liberation but also the production of fine particles that can pose problems during flotation (Trahar and Warren, 1976). The definition of the grinding requirement for flotation is a complex problem (Rickelton and Dell, 1977; Sosa Blanca et al., 2000; Morrison, 1993; Wei and Gay, 1999).This paper analyzes the effect of the fineness of grind using semi-batch flotation test results. The first two sections describe the test procedure and the results. The third section analyzes the results in terms of liberation and selectivity, and proposes a possible redistribution of power between grinding and regrinding mills."

Jan 1, 2006

By O. Mejia, J. Drozdiak

"This paper summarizes a comprehensive energy and cost study comparing an existing SAG mill based circuit at Huckleberry Mine with two proposed circuits involving comminution technologies which are associated with energy efficiency: high pressure grinding rolls (HPGR) and high speed stirred mills. The specific energy requirements expressed as kWh/t for the proposed circuits were determined from pilotscale HPGR and stirred mill testing conducted at the University of British Columbia. Samples and operating data were collected from Huckleberry’s copper-molybdenum concentrator to evaluate current mill performance for comparison. To support the base case, the SABC circuit was modeled using JK SimMet® software. The main comparison focused on the complete energy requirements for each circuit, including materials handling equipment such as conveyors, screens, feeders and pumps. This paper also provides capital and operating cost estimates for each of the comminution circuits. The results showed that the HPGR - ball mill circuit achieved a 21% reduction in energy consumption over the existing SAG - ball mill circuit at the same P80 grind size of 160 µm. At a grind of 80% passing 75 µm, the HPGR - stirred mill circuit showed a 34% reduction in energy compared to the base case. It was concluded that the energy reduction for the new flowsheets significantly improved the economics of the Huckleberry comminution duty.INTRODUCTIONUp until now, tumbling mills such as AG/SAG mills and ball mills have had a dominant bearing on the design and economics of comminution circuits. However, it is commonly agreed that the majority of employed comminution processes are energy intensive and energy inefficient, accounting for up to 80% of overall process plant energy consumption and having an efficiency of as low as 1% (Abouzeid and Fuerstenau, 2009; Fuerstenau and Abouzeid, 2002). The U.S. department of energy reported that there is a potential to reduce energy consumption in the metals industry by up to 61% from current practice to bestestimated practical minimum energy consumption; suggestions included the implementation of best practices and the adoption of energy efficient mining and mineral processing technologies such as advanced blasting techniques, high pressure grinding rolls (HPGR) and stirred mills (U.S. DOE, 2007)."

Jan 1, 2013

By Gao Dazhao

This paper presents some research results of pile foundation performance. Measurements on the bearing behaviour and driving effects of piles have been carried out during pile testing and pile driving. It has been found that the ratio of end resistance to the ultimate load depends on the pile length, and the ratio in general is less than 40% for single piles. However for pile group, the end resistance seems to be greater than skin friction. The characteristic curves of skin friction and end re­sistance appear as interaction between soils and pile. The contribution of skin friction to the pile bearing capacity not only depends on soil properties but also on the relative position of the soil layer. The pore pressure and the lateral pressure in ground have been observed during the stage of driving piles. Based on the available data, the radius of plastic region and the coefficient of pore pressure A can be found analytically. The pore pressure time process curves which may be used for practice have been predicted by means of numerical method.

Jan 1, 1991