Search Documents

By W. Barthel, B. A. Dippenaar, J. Malan

In its most basic form, the process of sintering is very simple, and has been in use since the turn of the previous century. However, while the basic process is simple, control of the process relies on a number of extremely complex interdependent process parameters and requires a thorough understanding of the effect of these parameters on production capacity and product quality. Further, as with many other processes, the process parameters and hence design details of visually similar installations are highly dependant on the specific feed materials. While the industry trend has been towards an increase of capacity in order to lower unit production cost, typically in Iron ore sintering plants, this approach is not always possible for other commodities because of the scale of operation. This paper seeks firstly to describe some design considerations of sinter plants; secondly, to report on results from testwork performed with a specific series Manganese ore blends; and last, to relate these results to the design of new small-scale Manganese ore sinter plants.

Jan 1, 2004

By P. K. Sahoo, C. R. Ray, S. S. Rao

This paper deals with various factors affecting the strength of chromite briquettes which plays a vital role in the smelting of charge chrome / ferro chrome production. Appropriate briquetting parameters like molasses and lime binder level, molasses quality, particle size distribution and segment condition etc. are essential to guarantee quality briquettes in the successful use of briquette and chromite ore fines. In developing a technology for briquetting of chromite ores, it is important not only to study the grain size characteristics of the chrome ore fines but also to make an informed choice of the type and quality of the binder and the condition for producing a physically and chemically competent green and cured briquette. This paper also describes the effect of strength of briquettes on various parameters of charge chrome production as the use of quality briquettes in the production of high carbon ferrochrome alloys has a number of operational, metallurgical and economic advantages. It is also a requirement for submerged arc furnace operation that the charge be adequately porous to allow gaseous products of the reduction reaction to escape from the furnace charge burden without hindrance. Otherwise, furnace material would erupt causing electrodes and furnace other equipments damage and risking the safety of the work force. The briquette, because it replaces lumpy charge but has an advantage of smaller size, allows for an uniform and porous charge so that the ascending gaseous products can escape freely. Finally this paper deals with furnace operational results with varying proportion of briquettes having same strength.

Jan 1, 2007

By D Rubery, C Croker

The Boddington Gold Mine (BGM) is located 120 km south east of Perth, Western Australia. The operation is managed by Worsley Alumina Pty Ltd and mined by contractor Henry Walker Eltin (HWE). The mine has been operating since 1987 with ore extracted from a series of pits along strike. Ore is contained within the basement rock, which is overlain by a cap rock layer and transition zone. Cap rock and basement zones require blasting.As the mine neared completion, a high-grade deposit was discovered within 50 m of an existing Western Power substation and 100 m from the processing mill. The substation provides power to the Boddington area and is a back-up power supply to the city of Perth. Due to the delicate nature of the transformers located at the power station, overhead power lines and the mill, blasting in the area was considered very high risk. As such blasting needed to be controlled for flyrock, airblast and most importantly peak vibration and frequency limits which had the potential to damage the transformers.The mine was due for closure in March 2001. The decision to mine the pit was based on its high grade, ability to be blended with lowering grades from other pits and changing of the processing technique with the expansion. This decision extended the life for a further six months.Due to the high potential risks a detailed risk assessment was conducted by Orica, Worsley and Henry Walker Eltin. The completed assessment and the major design parameters were presented to Western Power for approval. The ability to reduce the blasting risk was focused on limiting of vibration through controlling maximum charge initiated per delay, blast timing and firing direction, and other innovative control measures. OricaÆs SHOTPlan« and Sabrex« computer modelling packages were used to predict the outcome of blasts.The success of this project has opened the doors for other high risk blasting projects, which otherwise may be left unmined.

Jan 1, 2002

By Edwin E. Maust

In response to the ever- increasing demand for high temperature materials, the Bureau of Mines instituted a program for the study and development of superrefractories, One of the major tools obtained for use in this research was an image furnace of the double-paraboloidal mirror type. Although extensive theoretical analyses of solar furnace performance may be found in the literature, comparable detailed information on the double-paraboloidal-mirror image furnace has been nonexistent. This report presents an analysis based on an investigation undertaken to ascertain the limitations and characteristics of the furnace so that it can be used most effectively. The quantitative determination of the energy available at the image, the control of this energy by mans of a 60-inch iris diaphragm, and its variation with position and time relative to the heat source used have all been dealt with in detail. The quantitative results were obtained using a specially designed waterflow calorimeter and these measurements, in conjunction with the theoretical analysis, are used to present a fairly complete description of the furnace and its capabilities.

Jan 1, 1962

By Qiang Zhang

Hybrid composites are fabricated by adding two reinforcements into matrix materials so that the expected excellent properties can be achieved through the combined advantages of short fibers, and different size particles (micron or submicron), which provide a high degree of design freedom. In this paper, hybrid preforms were produced with the different size reinforcement of the Al2O3 particles and short fibers. The Al-Si alloy-based hybrid composites were fabricated by preform-squeezing casting route. The structure and performance of composite materials were studied with the Transmission Electron Microscopy (TEM), and Scanning Electron Microscopy (SEM). The results show that the reinforcements, both particles and fibers, distribute homogeneously in the matrix materials, and the properties of composites are found to improve in comparison with the matrix Al-Si alloy.

Jan 1, 2009

By J. H. Zietsman, S. Maharajh, J. Muller

In the chlorination process for TiO2 pigment production, blends of titania feedstocks such as ilmenite, synthetic rutile (SR), natural rutile, upgraded slag, and chloride-grade slag are reacted with coke and chlorine at a temperature of around 1000°C to form TiCl4 (the main product) and other waste metal chlorides. The TiCl4 is the main feed material for the TiO2 pigment-making process. Feeding different titania materials to the chlorinator affects the amount of coke and chlorine required for the process, the amount of waste generated, waste disposal costs, the amount of TiCl4 produced, and bed build-up rates. These factors influence the value of the feedstock. Generally, a higher TiO2 feedstock is more valued since less waste is generated and less reagents are consumed. To quantify the impact of different feedstocks on the chlorinator, a techno-economic model was developed to describe the chlorination process and estimate process variables at steady state. This paper describes the development of the model and studies in which the model has been used to quantify effects of using different feedstocks.

Jan 1, 2015

Experimental investigations were made into the decoppering of lead, tin, and bismuth using a technique which approximates on the small scale to industrial practice.Decoppering lead with sulphur alone in the absence of tin and silver did not proceed to low copper values. With a minimum of 0·02 per cent Ag or 0·10 per cent Sn, lead was decoppered to less than 0·01 per cent Cuby stirring with 0·2 per cent S over 10 min. Decoppering of tin or bismuth proceeded rapidly to very low levels in the absence of any "catalytic" impurities, at any rate in excess of those concentrations normally encountered in commercially pure tin or bismuth.

Jan 1, 1971

By M. Karmis, S. K. Weisiger

The traditional method for training personnel in the mining and other heavy industries has been face-to-face, either via a lecturer in a classroom or through an apprenticeship. With the advent of applications tools such as video, computers, and the Internet, however, a much broader range of training delivery methods is available. Especially exciting are the broad capabilities of multimedia packages that combine the best features of numerous delivery methods. Applying multimedia environments in training holds great potential, especially when there is considerable difficulty in reconstructing real training environments. The authors discuss various delivery methods currently used in training employees, including perceived advantages and disadvantages of those methods. The authors then discuss and evaluate current computer-based training efforts of the mining industry and present an example of a multimedia training tool.

Jan 1, 2001

By Mary E. Cocklan-Vendl

Regulatory processes associated with development of major mining operations in Alaska and British columbia were evaluated using specific case studies. Included were one hard rock mine in Alaska (Red Dog Mine), one hard rock mine In British Columbia (Snip Mine), and one offshore gold dredging project in Alaska (WestGold SIMA). Based on a comparison of the three case studies, it became clear that the primary incentives for cost effective permitting are: 1) early and continuing coordination of proposed project plans, designs and schedules with key regulatory agencies and local area residents and 2) development of a sufficient level of baseline information on air quality, water quality, wetlands, endangered species, fish and wildlife, and socia-cultural conditions to support the required permit application. The U.S. permitting process worked in much the same way as the Canadian permitting process. Disincentives of mine permitting include high initial costs for baseline data gathering. However, a relatively high early investment resulted in more efficient permit acquisition and reduced long-term monitoring requirements. A common problem Identified was the inadequate supply of trained agency personnel with the requisite technical and permitting experience. This sometimes resulted in poor decisions and unnecessary changes in project plans and schedules.

Jan 1, 1993

By J. Trckova, P. Prochazka

Physical models from equivalent materials satisfying geometrical and physical similarity have been constructed. A special technology of simulating the excavation of an opening at the front part of a tunnel and of measuring the deformation at the tunnel face was applied. The results yielded by the physical models were used to formulate constitution relations in the numerical solution. This coupled modelling enables us to predict the behaviour of tunnel structures more accurately. On a construit des modèles physiques, réalisés en matériaux équivalents et répondant aux conditions de ressemblance géométrique et physique. Sur ces modèles, on a utilisé une technologie intéressante de simulation du forage du tunnel et de la mesure de déformation du front de taille pendant le forage en progression. Les résultats donnés par les modèles physiques ont été utilisés pour formuler les relations de constitution dans la solution numérique. Une telle construction de modèles combinés permet de prévoir plus précisément le comportement de la structure du tunnel. Es wurden physikalische Simulierungsmodelle aus äquivalenten Werkstoffen konstruiert, welche die Bedingungen der geometrischen und physikalischen Ähnlichkeiten erfüllen. Bei diesen Modellen hat man die interessante Simulationstechnologie des Tunnelvortriebs sowie die Verformungsmessung beim Tunnelabbaustoß während des Vortriebsvorgangs eingesetzt. Die Ergebnisse der physikalischen Simulation wurden zur Formulierung von Konstitutionsrelationen in der numerischen Lösung genützt. So eine kombinierte Simulation erlaubt eine genauere Prognose des Benehmens der Tunnelstruktur.

Jan 1, 2003

By W. L. Saunders

(Wilkes-Barre Meeting, June, 1911.) I. INTRODUCTION. IT is now generally admitted by experts that at least so far as rapid progress is concerned the Alpine system of tunnel-driving is superior to any other. This is perhaps natural in view of the record of experience in driving tunnels through the Alps. These great mountain-chains cannot be treated in the ordinary way by shaft-sinking and driving headings, thus multiplying the points of attack. The work must be done from the ends only, hence speed in driving is of the utmost importance; and, as necessity is the mother of invention, the concentration of effort to make progress has resulted in an organization and in mechanical appliances that have produced results so much in excess of the usual practice, even in America, that a discussion of the subject in detail should be of much value to the engineer and contractor. The first Alpine tunnel was the Mont Cenis, length 7.5 miles, driven with a progress that averaged about 7.75 ft. per day. Next came the Saint Gothard, 9.5 miles long, 18 ft. per day; Arlberg, 6.5 miles long, 27.25 ft. per day; Simplon, 12.25 miles long, 36 ft. per day. The figures represent progress when driving from two headings, so that by dividing them in two we get the daily single-heading progress. The latest of the Alpine tunnels is the Loetschberg, now being driven. In this work the world's record has been beaten by a single day's record in one heading of 36 ft. and by an average daily record in. one heading of 29.5 feet. The Alpine range forms a natural barrier between a large section of northern and southern Europe. This range extends from the southeast of France to the frontier of Hungary, between Italy and the plains of southern Germany. The contour

Jul 1, 1911

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill. The design of the Hicom mill is unique. Based on a high speed centrifugal motion of the grinding chamber, very high power intensity is delivered to the grinding process. Most significantly, a high acceleration field, 50 times stronger than gravity is produced, creating very high power input per unit of mill volume, and exceptionally fast particle breakage rates, typically 50 - 100 times greater than those in conventional tumbling mills. A mill developing such forces has significant implications to comminution technology and practice.

Jan 1, 1999

CAPTAIN JOHN H. BALLAMY John H. Ballamy, Captain on the Regimental Staff of the 103d Engineers, was killed near Fismes, on August 9, 1918. Captain Ballamy was born at Plymouth, Pa., in 1886 and graduated from the High School of that town in 1903. In the following year he began work as a coal miner, and at the same time began the study of mining engineering in the evening and any other spare time. He continued this diligent and energetic practice for many years. For sixteen years he continued in the employment of the Delaware, Lackawanna & Western Railroad Company's coal mining department, first as a practical miner, next as rodman on the survey corps, of which he soon became chief, then draftsman and mining engineer in the company's office. In January, 1916, he was promoted to the position of district engineer in charge of mining engineering work. He became a member of this Institute in September, 1917. CAPTAIN JOHN H BALLAMY. Captain Ballamy's military experience began at the same time as his engineering practice. He was a charter member of Company A, Engineers, N. G. P., which was organized ten years ago. He saw service on the Mexican border as First Lieutenant of this Company, and remained in that position until November, 1916. In July, 1917, he was again called into service and was sent to Camp Hancock, Ga., with the 103d Regiment of Engineers. Before joining this regiment he attended a school for officers at Fort Sill, Okla., where he received special training in field fortifications. In December, 1917, he was commissioned Topographical Captain on the Regimental Staff, and in April, 1918, preceded his regiment by about six weeks to France, where he again attended an officers' training school. He rejoined his regiment on July 15, near Chateau Thierry and was killed near Fismes on August 9, 1918.

Jan 11, 1918

By C. Bise, A. Seal

Excessive noise has long been a hazard in the coal-mining industry. Studies conducted during both the mid-1970s and the mid-1990s consistently show that hearing hearing loss within the mining industry persists, in spite of regulatory requirements and sampling technology advances. When MSHA’s new health standards to protect miners from hearing loss took effect in September 2000, the potential developed to re-evaluate sampling approaches with regard to noise-source hazards, such as task-based methods. This paper describes results from a Penn State research project currently being conducted at an underground coal mine. Each occupation was reviewed, and a list of tasks or processes performed by each was generated. Traditional personal noise dosimetry, static sound pressure levels, and equipment sound mappings have been performed. Job tasks indicating the greatest levels of daily noise exposure and contributions to noise dose have been identified and will be discussed.

Jan 1, 2001

By G. K. Mann

Fragmentation analysis of blast or crushed rock material is a time-consuming and costly process. During the last two decades, the mining industry has been investigating image-based analysis systems as an alternative to generate fragmentation results. Many image-based techniques and commercial products have emerged during the last few years, and the mining industry has recently begun using these tools for real-time estimation of size distributions. Some existing systems require manual image editing to add or delete edges (or net) before executing the fragmentation analysis routine. This manual procedure may take hours of time for each image analyzed. Reliable and robust image segmentation should be able to handle a wide range of rock textures and sizes under a variety of lighting conditions. This paper describes a novel software application, which has the capability to autonomously capture images and analyze them to generate the particle size distribution. The system can also process a batch of images captured during a fixed duration of time and produce the overall particle size distribution. The new method has different layers of segmentation modules, which allows the system to operate under a wide range of rock textures and lighting conditions. A new grey-level slicing technique is developed which can perform under a range of illuminating conditions. The Canny-based edge detection technique is used to segment rocks appearing in dark regions.

Jan 1, 2006

By R. G. Bottge

To better understand those factors which increase mining costs in Alaska, a Bureau of Mines study was conducted to compare the estimated costs of operating a 100,000-tpd open pit copper mine located on a hypothetical ore body in the Lake Clark area, Alaska, with the costs of mining a similarly sized hypothetical copper ore body near Tucson, Ariz. The information derived should be beneficial to the State and Federal governments in appraising the potential for development of large, low-grade porphyry copper deposits in south-central Alaska. Conventional mining and concentrating methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The total price required for copper mined in Alaska and Arizona was $1.12 and $0.63 per pound, respectively, plus or minus 20 percent. These values were obtained assuming no leaching of low-grade copper, recovery of gold, silver, and molybdenum as byproducts, 100-percent equity financing, and a 12 percent discounted cash flow rate of return. The average domestic and international prices for copper in July 1973 were $0.60 and $0.916 per pound, respectively. The existence of a developed transportation and power system in Alaska would have reduced capital and operating costs subs tantially. The required price for copper would have declined from $1.12 to $1.05 per pound, plus or minus 20 percent.

Jan 1, 1974

By Thomas J. Crocker, Douglas B. Uthus

Tunnel Boring Machines (TBM) have gained worldwide acceptance in the construction field and are being employed in ever increasing numbers to drive underground transit lines, drainage systems, etc. However, TBM utilization in the mining industry, and more specifically coal mining, has been very limited. This paper reviews past and present applications of TBMs to coal mining and examines the needs of the industry in an attempt to offer some insight as to what a TBM system must provide if the excavation potential demonstrated in civil works projects is to be realized in coal operations. EUROPEAN EXPERIENCE Germany The Germans recognized long ago the potential of mechanized drivage for coal mine entry development. Early in the 1960's experimental runs were made with a full-face Wohlmyer roadheader at the Westerholt Mine and trials were conducted on a roller bit armed full-face Bade roadheader. But because of problems with penetrating the various carboniferous strata occurring in changing sequence and hardness, these first attempts were soon terminated. After viewing later successes in the construction industry with improved TBMs, new attempts were initiated by the German mining industry in 1971 to mechanize drivage of their development entries. Four TBMs of two different types were placed in operation.

Jan 1, 1976

By M. Rebolledo, N. Mora, G. Zarate

For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Jetti Resources has developed a novel hydrometallurgical alternative to extract metals of value from mineral ores that the mining industry has struggled to process. Jetti’s catalytic technology, whilst being especially advantaged for extracting copper from low-grade and highly refractory minerals, such as chalcopyrite, seamlessly integrates with existing heap leaching methods and downstream processing operations. The technology uses a catalyst which weakens the metal-sulfide bond in the crystalline structure of the chalcopyrite mineral and alters the structure of the passivation layer allowing the leaching process to continue. Metallurgical test work was conducted to examine the effect of ore variability, in terms of grade and copper deportment. The results presented in this study highlight the amenability of the technology and demonstrate that it is possible to enhance leaching performance of copper primary sulfides over a wide range of copper grades, from 0.1 to 2.2%. Further, it is concluded that despite the copper grade, the tests with increasing chalcopyrite content render copper recoveries up to 4 times higher compared to the tests under non-catalyzed conditions. Jetti’s catalytic technology is currently being evaluated at larger scales, namely a commercial dump leach operation and 50-tonne crib tests. The results obtained thus far are compared to the results from conventional sulfide heap leaching tests. INTRODUCTION For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Chalcopyrite (CuFeS2) is the most abundant and recalcitrant of the copper sulfides (Singer, 2017). Owing to its abundance and economic importance, it is the most demandable natural source for copper worldwide. In fact, the projected demand for copper is further expected to rise much higher beyond the current demand by the year 2020 (Panda et al., 2015). Therefore, it becomes imperative to find low intensity hydrometallurgical technologies for the extraction of copper from chalcopyrite in ores of such low-grades that are un-economic to concentrate and to augment the supply by extracting copper from ores with complex mineralogy that cannot be concentrated (Watling, 2013).

Jan 1, 2019

By M Sherman

The challenge facing the engineering provider is to calculate throughput rates when faced with disparate specific energies calculated by different testing methodologies. Typically, an ownerÆs team would expect that the throughput calculations be checked using more than one method, therefore it is inevitable that there will be differences, based on which methodology is used. This engineering challenge is exacerbated by the continuing evolution of contemporary circuit configurations such as two stage pebble crushing with or without high pressure grinding rolls (HPGRs) as the second stage, or second stage pebble crusher product reporting to the ball milling circuit, etc.This paper is a companion to the paper first presented at SAG 2011, which showed that the Bond Indices are an excellent tool for estimating the specific energy requirements for semi-autogenous grinding (SAG) mills in single-stage SAG milling (SSS) circuits, SAG and ball mill circuits (SAB) or SAG and ball mill circuits with pebble crushers (SABC). This paper presents how the Bond Indices have been used to calculate ball mill specific energies, and therefore throughput rates, for SAG mill based circuits. Once the ball milling specific energy is known, tower mill and vertimill energy requirements can also be calculated. It is noteworthy that the method presented in this paper does not require the use of any unpublished correction factors: the proposed method uses the Bond parameters and equations published by Rowland in 1982.CITATION:Sherman, M, 2013. 21st century bond, in Proceedings Iron Ore 2013 , pp 309-312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013