Search Documents

By David O. DeGagné

While mine backfill plants are becoming increasingly more automated and instrumented, especially with paste fill operations, underground backfill distribution systems have hardly changed over the years. While fill properties are appropriately measured in the preparation plants, as backfill enters the mine borehole, the technology for control, data gathering and reporting is somewhat lacking. Mines typically experience problems with borehole and pipeline plugging, pipeline bursting, bulkhead failure and exposed fill sloughing. With adequate instrumentation of the backfill system it is possible to obtain a complete, continuous and detailed picture of the entire filling operation from preparation to post-pour. Good data will, over time, provide the basis for needed improvements of backfill systems and will be essential to safer, more efficient and less costly fill practices. This paper will review the areas of the filling operations where monitoring would prove critical to eliminate failures such as pipelines, bulkheads, fill exposures, stope walls, etc. The types of monitoring systems currently available will be reviewed and potential areas for development will be highlighted.

May 1, 2001

Structurally- controlled deep leaching processes have removed vast quantities of carbonate from a substantial portion of the "silica-dolomite" enclosing the 500 copper orebody. Mine drainage subsequently allowed free access of air to the porous environment created and oxidation of sulphides commenced. During the mIne development stage the exothermic and temperature-dependent nature of these hydrolysis reactions resulted in a slow general elevation of ground temperatures. and levels of 90 - lOO°C were attained in restricted moist sulphide-rich areas.With the advent of production and extensive use of explosives, the oxidation processes were locally raised to new levels of activity. Direct interaction of explosives and sulphides in favourable conditions caused temperature rises to above 260 C. Above this point the dry oxidation of sulphides in air was initiated and rapid escalation to the vicinity of 800 C has been known to occur in isolated cases.Ground reactivity is a function of the complex interrelationship of several controlling factors and no simple index exists.Control techniques are presently aimed at prevention of temperature rises in the range 100 -260 C. Inhibition of the rapid dry oxidation processes above 260 C is difllcult and current efforts have met with only partial success.

Jan 1, 1968

The Leigh Creek Coalfield is owned and operated by the Electricity Trust of South Australia to supply fuel to the Northern Power Station. To supply electricity at lowest cost, a costing and decision process that establishes the role of the Leigh Creek Coalfield in the overall system planning and operation is required. The costing is integrated in that it is based not just on a particular mine plan but on the wider need to supply a particular electrical demand. The detail costing has evolved over time from manual to main-frame computer to microcomputer techniques. Now there is a choice between fast consistent costs and a slower but more detailed and flexible costing.

Jan 1, 1990

IN concentrating mills, where several millerals are recovered for realisation in more than one product, various systems are used to express the relative economic value of the work done, and, in the hope that it may prove of use to other operators, the writer will describe a system which, in his opinion, is more complete than any other that he has seen published.The controlling factor in all mill work must be based on the economic result represented by the greatest margin possible between the realizable value of the products and the cost of obtaining same.From a mill-man's point of view these are affected by the following factors:1. Metal contents of ore.2. Grade of products.3. Recoveries.4. Working costs.The grade of ore milled is usually outside the mill-man's control, but this may exercise a considerable influence on the grade of his products, metal recoveries, and revenue per ton of ore. Higher grades or recoveries may be obtained by using a more expensive process, or by additional grinding or reagents, and the economic comparison can only be arrived at by obtaining an analysis showing the monetary value of each variation within the possible limits.In the system to be described, the value of unit variations of metal contents of the ore, grade of products and recoveries are calculated in terms of a monetary unit per ton of ore with the returning charges ruling, and any suitable metal prices. To do this it is necessary to assume what, for convenience, is termed a "standard" set of results from the mill, preferably representing about average conditions, and having calculated the effect of unit...

Jan 1, 1931

By Rhulani F. Maluleke, Francis W. Petersen, John H. Marsh, Johann de T. Steyl, Allan Nesbitt

"Pressure leaching of chalcopyrite and nickeliferrous pyrrotite at temperatures between 105 and 200 ºC has been proposed as a potentially viable route for the extraction of mineral elements from sulphide concentrates. In general, these concentrates contain iron, and the economic success of the processes is partially dependent on the choice of the environmentally acceptable iron-removal technique. One of the most widely used methods for the removal of iron from sulphate liquors is precipitation as hematite, goethite, or jarosite. The nature of the iron precipitate formed, dictates downstream dewatering and residue treatment and disposal options. However, a better understanding of iron precipitation under the defined process conditions would consequently be of benefit in process design and optimization.This study investigated the precipitation of iron in the autoclave at temperatures between 105 and 200 ºC. The effects of temperature, acid concentration, iron concentration, and the presence of other metal cations on the nature and composition of the precipitates were determined."

Jan 1, 2003

By Andy Cole, Ken Thomas, Stephen Durn, Jacques McMullen

"The roasting and gas handling circuits of the Barrick Gold’s new Roasting Facility at the Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Product from the up-stream dry grinding circuit requires roasting to maximize gold recovery. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type “double refractory” ores. Double refractory is indicative of the gold being difficult to direct leach due to a combination of pyrite encapsulation and the carbonaceous preg-robbing of the ore.A very extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NO, reduction before venting to the atmosphere.The roasted calcine is quenched, neutralized and then thickened before leaching in the carbon-in-leach-circuit.INTRODUCTIONBarrick’s strategic development plan integrated the production of gold from Goldstrike’s carbonaceous ore reserves by 2000. A due diligence review of carbonaceous ore processing options was initiated during the second half of 1 996. Processes considered included autoclaving followed by a proprietary ammonium thiosulfate leaching process, fine grinding/autoclaving as practiced then by Santa Fe, and whole ore roasting as practiced by then Independence Mining and Newmont. The objective by year-end was to recommend the most robust and economical process for Goldstrike’s carbonaceous resources. In the fall of 1996, a detailed review of roasting as a processing alternative for Goldstrike was initiated."

Jan 1, 2001

By B. Anameric, S. Kawatra

Pig iron nuggets, which have similar chemical and physical properties with blast furnace pig iron, were produced by a single step heat treatment of self reducing – fluxing dried greenballs. During this single step heat treatment the transformation of self reducing fluxing dried greenballs into pig iron nuggets did not take place instantaneously. Rather, it was composed of three transformation stages, (1) transformation of self reducing – fluxing dried greenballs into direct reduced iron (DRI), (2) transformation of DRI into transition direct reduced iron (TDRI), and (3) transformation of TDRI into pig iron nuggets. Thus, the objective of this research was to investigate these transformation mechanisms by analyzing the transformation stage products. The transformation stage products were produced at a constant furnace temperature of 1425°C and various furnace residence times. They were characterized according to their microstructure, microhardness and apparent density. The changes in the product’s physical and chemical properties with furnace residence time were utilized in understanding the transformation behavior, the chemical events that took place and the controlling mechanisms. It was determined that the transformations were dictated by the changes in the slag viscosity and wetting properties, and by carbon diffusion into metallized areas.

Jan 1, 2007

Confidence in the strength of the U.S. economic recovery was considerably enhanced by third quarter 1983 profits, which showed a 12.8-percent increase over those in the second quarter (table I). Although the increases were not as great as between the first and second quarter of 1983, profits have grown each quarter since fourth quarter 1982. Both total profits and profits per unit of output increased, which the Bureau of Economic Analysis (BEA) attributes to decreases in labor and nonlabor costs (per unit of output), as well as to moderate price increases. [ ] A number of durable goods sectors, however, continue to show profit declines, especially electrical and non-electrical machinery. Profits in the primary metal industry are still negative, but the economic picture of this industry is improving. Between the second and third quarters of 1983, capacity utilization increased somewhat in primary metal manufacturing and stone and earth mineral mining but did not change at all in metal mining. Capacity utilization in metal materials increased from 47.4 percent in the fourth quarter of 1982 to 64.2 percent in the third quarter of 1983 (table 2).

Jan 1, 1983

Waitemata Tectonic Event(25 Ma ago) created a subduction system from the northeast of Northland, causing: (1) the emplacement of the Northland Allochthon (24-23 Ma) which provided argillaceous limestone and serpentine to Northland, and minor copper to both there and East Cape (located off Northland then); and (2) Northland volcanism (from 22 Ma), which lacked economic mineralisation. The Kiwitahi Tectonic Event (1714 Ma) caused: (1) a realignment of volcanism - from coastal western Northland, to west of the Hauraki Plains (Kiwitahi); (2) a start to the migration southwards from Northland of (a) the Alpine Fault System towards Marlborough today, (b) subduction towards Cook Strait, and (c) volcanism towards Taranaki-to-Bay of Plenty (initially through Coromandel, Kiwitahi, and offshore west coast); and (3) a start to rhyolitic volcanism & associated hydrothermal activity. The latter caused epithermal mineralisation, providing in Coromandel the best known North Island metalliferous deposits. Andesitic volcanism has been active in both of these two contrasting, subequal belts since 22 Ma. Rhyolitic volcanism and hydrothermal activity was wholly restricted to the eastern Marshall Belt, with an abrupt limit to economic mineralisation at the Volcanic Divide (within Hauraki Plains) and a major change there to basaltic volcanism of the western Searle Belt. The Kaimai Tectonic Event (5-1.5 Ma) caused: (1) a temporary reversal in volcanic migration in the Searle Belt, and a duplication of rhyolitic & hydrothermal activity at Waihi (Marshall Belt); (2) the rotational rifting of both the Central Volcanic Region (by 30¦) and the Hauraki Rift (10¦), causing major curvature of the North Island and New Zealand, and the transfer of the offshore subduction system from Coromandel to East Coast; and (3) an effective end to Coromandel mineralisation. Post-Kaimai Volcanism (1.5-0 Ma) included: (1) andesitic volcanism in the Searle Belt, yielding the western coastal titanomagnetite deposits; and (2) andesitic, and rhyolitic & hydrothermal activity in the Marshall Belt - the latter providing geothermal energy, sulphur, and pumice/perlite deposits. Post-Subduction (Intraplate) Volcanism (10-0 Ma) developed in a steadily expanding northwest region of relative tectonic quiescence, as subduction and its volcanism migrated southwards. Intraplate volcanism was predominantly basaltic, providing excellent aggregate; but less common rhyolitic & hydrothermal activity provided geothermal potential and mercury at Ngawha and at Puhipuhi, and halloysitic clays of extreme brightness elsewhere in Northland. This volcanism has reached as far SE as Mayor Island, providing an early New Zealand mineral resource - obsidian.

Jan 1, 1997

NEW MEMBERS The following list comprises the names of those persons who became members during the period Oct. 10, 1916 to Nov. 10, 1916. ANCHOR, HANS C., Supt., Dome Extension Mines Co., Ltd., South Porcupine, Ont., Canada. BABCOCK, EARLE J., Dean, College Of Min. Engrg., State Univ. Of N. Dak., Grand Forks, N. Dak. BIDDIS0N, P. McDONALD, Construction Engr., The Ohio Fuel Supply Co., 52 W. Gay St., Columbus, 0. BOISE, PAUL T., Asst. Mgr., Stimpson Equipment Co., Felt Bldg., Salt Lake City, Utah. BOURNE, RALPH H., Vice-Pres Whiting Foundry Equipment Co., Harvey, Ill. BROWN, EDWARD OTTO FORSTER, Min. Engr., 706-707 Salisbury House, London, E. C., England.

Jan 12, 1916

By J. Muller

Keywords: Pyrometallurgy, blast furnace, slag viscosity, slag liquidus temperature, phase equilibria The viscosity of molten slag in blast furnace operations is an important process variable, influencing the rate and location of reactions inside the furnace, as well as the ease with which the final slag could be removed from the furnace. To optimize these processes, it is necessary to estimate the slag viscosity and liquidus temperatures as accurately as possible, and know the target values. Models to predict viscosities and liquidus temperatures, incorporating phase equilibrium calculations, have been developed and validated with measured data. Various diagrams have been developed to illustrate how the properties vary with composition and temperature, including pseudo-ternary diagrams of SiO2-MgO-CaO-Al2O3 for viscosity and liquidus temperature. Models were also applied and methodologies developed to analyse historical blast furnace operations and determine target values.

Jan 1, 2011

By Eric Schraml

Wardrop Engineering and the Placer Dome?s Campbell Mine Design Team utilized leading edge directional raise boring techniques and an innovative, remote controlled application of steel fibre reinforced shotcrete ground support to achieve improved mine ventilation and a superior, safety focused secondary emergency egress. While more standardized methods may have provided a sufficient solution to either the requirement for a ventilation raise or for a traditional escape ladder way, innovative methodology ensured both objectives were met with a single, enhanced solution. Placer Dome committed to provide a solution that minimized energy consumption, optimized air delivery and facilitated an escape way focused on minimizing the negative physiological aspects associated with mine evacuation. The project was successful in providing a new airway, returning 47 m3/s (100,000 cfm) from the 39 Level to 30 Level, minimizing risk to the raise equipping crew and providing a fully equipped escape hoist. The resulting secure escape environment provided an efficient means of evacuating personnel working at depth without necessitating a potentially dangerous exhausting climb to surface. The project has substantiated, that optimized safety focused design can be achieved without jeopardizing project economics.

May 1, 2002

OWING to two large falls of ground which resulted in serious accidents occurring towards the end of 1908, it became evident that the "open chamber" system then in use was unsuitable for the conditions existing in the Mount lVIorgan mine. It will be admitted that in all mining operation, the first consideration is the economy of the system adopted, combined with its safety and ability to give the desired output. A sectional system with square sets has been introduced into the mine, in which due attention has been paid to these factors. In this paper a brief description of this system will be given. An outline of those previously used will be ineluded, as it is necessary to understand the eonditions which existed in the mine at the initiation of the sectional system. Outside the actual mining methods employed, various points that might prove of interest will be touched on.The square set system of mining has been in use throughout the stopes in the gold ore in the upper levels of the mine since underground operations were started in Mount Morgan.

Jan 1, 1910

By R. Pickering

The purpose of this paper is to explore the application of technology to stoping systems. Technology, because for the past 100 years the South African narrow reef mining industry has battled to control working costs in a labour-intensive industry. Stoping systems, because it is the stoping method and methodology which is at the heart of the mining system. Introduce a more efficient stoping system and the mining system will look after itself. The technology applied to stoping over the past 100 years can be categorized as follows: ?The introduction of pneumatic rockdrills early this century, the cumbersome rig mounted units being replaced by smaller, lighter hand-held units which were then made easier to use with the addition of an air leg ?Scraper winches to replace gravity and shovels to move rock both in the face and the gullies were first introduced in the late 1920s ?Hydraulic props as a support method arrived in the1960s ?Some people argue that tungsten carbide inserts were equally important. There have been a number of attempts to introduce different technologies into stoping, the most recent being trackless equipment. Where the stoping layout suits the technology it has been successful. There have been too many instances where a technology has been installed because it is fashionable. At the end of the day the outcome from change in the stoping systems has to be safer and more profitable mining systems. It is the contention of the author that change is only likely to be effective if it is supported by the introduction and application of appropriate technology.

Jan 1, 1999

Efficiency, Economics, Energy and Emissions - Emerging Criteria for Comminution Circuit Decision Making

Sep 13, 2010

By J. S. Stachulak, K. A. Mackinnon

This paper deals with specifying and evaluating fans for mine ventilation projects. Topics such as fan and equipment design life, operating points, and operating conditions are discussed. Common operating problems, such as vibration, parallel operation, mechanical failure, erosion, corrosion, and deficient fan performance are covered. Apart from identifying the potential operating problems, likely causes and suggested remedies are given. Fan type, fan accessories, and likely system effects and fan testing are discussed. Suggestions on what should be covered when evaluating different fan options and proposals and suggestions on the verification of supplier claims and guarantees, including cost of operation, the evaluation of initial capital cost, estimate on maintenance costs, and likely replacement expenditure over the life of the fans. In addition, fan reliability, operational flexibility, suggested construction details and fan vendor past history and experience are reviewed.

Jan 1, 2004

By J. Mason

In order that the use of continuous mining machines be most economic, the equipment must be operated at rated capacity as much of the time as possible and downtime for repairs kept at a minimum. A large factor influencing any proposals for maintenance programs is the complexity of the machines—often the intricacies of the precision-built equipment requires engineering knowledge byond the scope of mine maintenance personnel. A training program is part of the answer; there are others. In addition to investigating a joint company-manufacturer equipment-design improvement program, Mountaineer Coal Co. has launched a detailed preventive maintenance program to combat extensive downtime often encountered when continuous miners are used. Everyone in the coal industry knows the importance of operating continuous miners at their rated capacity as much of the time as possible. The potential capacity of the miner is such that l-min. delay means from 3 to 8 tons of coal lost. Today's miner is a well designed, precision-built machine, complicated with hydraulic and electrical equipment and complex mechanical assemblies with all possible combinations of gears, levers, and rods. As the machine becomes more complex, the problem of maintenance becomes more acute. The transition from conventional to continuous mining has taken place so rapidly that the mine mechanic has been unable to keep pace. When there is a machine failure, the maintenance man usually employs either the trial-and-error or the play -it-by-ear method of repair, but this represents an expensive proposition. Mine mechanics, maintenance superintendents, and mine managers complain about the complexity of the machines and how difficult it is to keep them running. There is no shortage of skill in the design offices. Machines are designed by good engineers, but for engineers. What's the answer? Better trained maintenance men—better maintenance instruction—better field service. These are all good corrective measures, but the real cure is to provide for the men at the do it level. Designers have got to cooperate with men to simplify maintenance on the increasingly complex machine. The designer must be aware of how his machine can be maintained. Sometimes a simple design change in a bearing, oil seal, or a bushing will correct recurrent breakdowns. Parts such as filters, hydraulic cylinders, hoses, and pivot pins can be better arranged on the machine to make them accessible so that the mine mechanic can easily keep the machine producing. Therefore, to get our maintenance off on the right foot, the program must begin back in the design office, before the machine is delivered to the mine property. Realizing the importance of this aspect, our company set out on a joint company-manufacturer equipment-design improvement program. This is a formal program in which quarterly reports are written covering machine defects, design weakness, and general problems relating to machine maintenance and performance. The manufacturer in turn comments on each and every item appearing in these reports, indicating the action he proposes to take. In addition to the written reply, meetings are scheduled with manufacturer representatives to discuss further the outlined problems. The benefits realized from this organized program are both substantial and far reaching. Good maintenance begins with a good design. The subject of preventive maintenance is not a new one. Volumes have already been written on the subject. It consists primarily of doing the maintenance work when you want to rather than when the machine demands it. However, a preventive maintenance program can be overdone. Theoretically, if carried to ridiculous extreme, all working time could be spent inspecting and repairing the machines and no time would be left for production output. Our goal in maintenance is to maximize running time for all machines, and to prevent or at least minimize production downtime. INSPECTION AND REPORTING The center of any preventive maintenance schedule is regular and systematic inspection, but it must be

Jan 1, 1961

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

The Grand Isle sulfur mine is located in the Gulf of Mexico, approximately seven miles off the coast of Grand Isle, Jefferson Parish, La. The deposit is on acreage covered by oil, gas, and mineral leases originally issued in favor of Humble Oil & Refining Co. by the State of Louisiana which were continued, maintained, and redesignated by the U.S. Department of the Interior after passage of the Outer Continental Shelf Lands Act. The sulfur deposit was discovered in 1949 when Humble Oil & Refining Co. penetrated more than 200 ft of sulfur-bearing limestone in a zone between 1813 and 2075 ft below sea level. In 1954, Humble drilled ten more sulfur prospect holes, eight of which encountered sulfur ore. On September 19, 1956, Freeport Sulphur Co. acquired from Humble Oil & Refining Co, the sulfur rights underlying the tracts, and the actual design of the installation began the same month. The first structural contract was awarded in December 1957 and offshore erection began in June 1958. The initial phase of construction has been completed and production by the Frasch process commenced in April 1960. The estimated total cost of the project is $30 million, of which $8 million is the extra cost incurred by the necessity of offshore operations. More than $22 million was expended before production was started. GEOLOGY OF DEPOSIT Grand Isle is the third largest sulfur deposit in the U.S. The orebody embraces several hundred acres, but its outer limits are yet to be defined to the northeast, east, and south. Most Gulf Coast sulfur deposits occur in a caprock mantle of calcite (referred to as limestone), anhydrite, and occasionally gypsum, which covers the apex of an intrusive mass of salt. Commercial quantities of sulfur are usually confined to the calcite or limestone member. Most often such limestone is completely enclosed by dense anhydrite below and impervious sediments above, which effectively form a closed reservoir. The depth of the Grand Isle orebody ranges from 1800 ft to 2500 ft below sea level. Within the present boundary, the sulfur-bearing limestone varies in thickness from 220 ft to 425 ft, while the sulfur content varies an average of about 15 pct in the leanest hole to an average of about 30 pct in the richest. Rock containing less than 5 pct sulfur is not classed as ore, and holes assaying less than 20,-000 long tons per acre of sulfur in place are not considered commercial offshore. The sulfur enrich-

Jan 1, 1961

The 103rd Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 16th August, 2000. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past Presidents, our Members and other guests, among them the following: Reinie Meyer, President, The Geological Society of South Africa Dr Nielen van der Merwe, Chairman, The South African Institute of Rock Engineering Chris Fourie, President, Institute of Mine Surveyors of South Africa

Jan 1, 2000

A Simulation Study on Two-Stage Grinding with High-Pressure Roller Mills By the application of high-pressure roller mill (HPRM) in the field of mineral processing, computer simulation can be used to predict overall performance of a grinding circuit based on data obtained from HPRM comminution test in pilot scale or industrial scale. Using the model developed by Klymowsky and Liu for HPRM comminution and an extended Plitt's model for classification, steady-state of a closed circuit grinding can be calculated by means of a virtual locked-cycle-test conducted on computer. This paper presents the result of a simulation study on two-stage grinding with HPRM as the comminution device. The emphasis is put on the influences of circuit-configuration and way of recirculating classifier's coarse-product on the overall circuit performance. The results show that two-stage grinding with HPRM has its merit and flexibility in meeting demands of various grinding tasks in mineral processing.

Sep 13, 2010