Search Documents

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor. At a large open cut copper operation, challenging geological structure resulted in slabby and blocky fragmentation in the stemming region, resulting in poor crusher throughput due to bridging. To overcome the poor fragmentation in the top of the bench, longer than conventional subdrill was used to precondition the top third of the bench. The technique significantly improved the run of mine fragmentation and resulted in feed to the in-pit crushers that is more consistent, which produced less crusher downtime due to bridging. A new method of quantifying the energy in a blast has been created. Termed the linear powder factor, or energy factor, the calculation considers the energy contributed by the subdrill of the upper bench and its impact on the energy in the lower bench. The technique enables blast designs to be optimised to deliver finer fragmentation and more consistent blast outcomes. To support the layer of preconditioned rock at the top of the bench, an innovative new device was developed. The device is inserted into the drill collar immediately after drilling and remains in position throughout the subsequent steps of hole depth measurement, priming, loading and removed prior to stemming. The device not only supports the broken rock at the top of the bench, but also minimises the amount of drill cuttings that fall back into the hole. Furthermore, the device helps protect the hole from damage by external factors such as weather events, drill tracks, vehicle tyres and movement around the collar during measurement and loading of the blast hole.

By Larry Schneider

Are you one of the thousands of hunters, fisherman, or hikers who purchased handheld GPS systems over the past several years and then been disappointed in their accuracy and performance. Or maybe you are one of the hundreds of blasters who have attempted to use GPS as a method for locating the exact position of their blast and measure distances from the blast to nearby structures. If so, you may have found that the accuracy of the handheld GPS systems left much to be desired. It may be time to get the units back out of storage and give them another try. As of midnight, May 1, 2000, the federal government has turned off the “error” built into the system known as “selective availability.” Here is a brief explanation of what that means in a question and answer format.

Jan 1, 2001

Westwood Quebec Long Life, Low Cost CONSTRUCTION UPDATE ? Shaft advanced to 840m (after 1 year), 3 km of down ramp and 2 km of exploration drift ? Head frame and hoist room structure completed ? 2009, 84,700m drilling program completed (increase 9%) 2010 OUTLOOK ? $102 million expenditures planned ? Shaft to advance to 1,300m and the first loading excavate 71,500m drilling program planned

May 1, 2010

By Frank Callanan

The Ameristar Casino expansion project included the design and construction of a 25-story hotel and 9-story parking structure expansion. The site is located in a floodplain on the banks of the Missouri River in Saint Charles, Missouri, where the underlying soils are potentially liquefiable. The geotechnical engineer performed subsurface exploration and analysis, which included site-specific seismic response and liquefaction, and provided geotechnical design recommendations. In the event of an earthquake, post-liquefaction settlement was calculated to be approximately 14 inches. Additional project constraints included wetlands protection, construction adjacent to the existing facility, flood protection and river bank stability. Because of the liquefaction issue, the geotechnical engineer consulted with a specialty geotechnical contractor on ground improvement methods. This consultation led to a proposal to eliminate deep foundations from the design and support the structures on shallow and mat foundations. The geotechnical engineer assisted the design team with foundation design analysis and value engineering assessments. Together with the project team, the geotechnical engineer used the data to evaluate foundation options and construction methods to overcome the site challenges and concluded that ground improvement was the optimum course of action. Because of the nature of the site constraints, a number of ground improvement methods were needed. The geotechnical engineer evaluated the methods proposed by the geotechnical contractor and provided the technical specifications for the ground improvement bid package, which included vibro-compaction, compaction grouting and micropiles. The ground improvement allowed for the use of shallow foundations (mat and spread footings), which provided the client with significant time and cost savings over the deep foundation alternatives.

Jan 1, 2009

By J. J. Wallace

This report describes the initial phase of Bureau of Mines research in the hydraulic mining of bituminous coal. The mining site and equipment are described, and the test procedures and results obtained with a bar-mounted monitor are given. Tests showed that hard Pittsburgh-bed coal can be mined hydraulically from a solid face at water pressures of 4,000 pounds per square inch.4 Coal was penetrated to a depth of 4 feet in 20 seconds with 225 gallons of water per minute coming from a 3/8-inch nozzle at 4,000 pounds per square inch pressure. Some difficulty was encountered in cutting the binders occurring in the coal; it was not possible Lu penetrate directly the overlying draw slate.

Jan 1, 1961

By Eugene H. Skinner

This Bureau of Mines report describes the fieldwork and subsequent analysis to determine physical properties, stress distribution, and several aspects of rock behavior as a necessary evaluation for a typical mine opening. All work was done at a test site on the 3300 level, Crescent mine, Coeur d'Alene mining district, Idaho. Free field stress beyond the influence of the opening was also determined. Conventional overcore technique with the three-component borehole deformation gage developed by the Bureau of Mines was used in three drill holes. Three field verification tests were performed using a gage newly developed by the Spokane Mining Research Center in an approach herein termed "initial deformation method." Use of this method validated that aspect of overcore theory which predicts that similar deformation effect occurs in the wall rock around the perimeter of an opening in rock under stress. Also described are all drilling procedures and performances. Physical property determinations were made on rock samples obtained from the three overcore drill holes. Twelve physical properties with a total of [532] values were obtained at various drill hole orientations and depths. Exhaustive statistical tests were utilized in the analysis of these physical properties. Further elaborated are statistical inferences based on these analyses. Extensive analysis and interpretation of Crescent mine geology are also described.

Jan 1, 1974

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By W. C. Lacy

This article is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The author feels that, although there does not appear to be any one technique or characteristics that will suffice as an index to the determination of stable slope angles, a combination of seismic methods as outlined here, detailed geological mapping and logging of core, and a better understanding of the angle of internal friction in rock types will permit accurate estimation. A mining engineer friend once remarked, "If we don't have pit slope failures, the slopes are too flat." Since economic justification of an open pit project is based upon ultimate pit slopes, we cannot wait until the pit is developed and slopes established by trial and error. Some combination of geological and/or geophysical techniques must be developed to permit accurate prediction of stable slope angles and to suggest modification of pit outlines to result in slopes enabling maximum economic yield. This presentation is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The principle of the weakest link applies to any slope stability evaluation and necessitates detailed geological examination and recording of observations. Physical failure will occur along any surface where shearing stress exceeds shearing resistance. Rock conditions are seldom uniform even within a single cut or pit face, so stability conditions will vary. Consequently, both plan outline and ultimate slope limits must be tailored to the specific situation. Economic advantages to be gained by slight increases in slope angles in deep pits are well recognized and stimulate efforts to obtain maximum permissible slope angles. MECHANICS OF SLOPE FAILURE Excellent reviews on the nature of slope failure have been presented+2,6,8,11 For the purpose of this study, the writer considers failure to take place by one or more of three processes: 1) ravelling, 2) translation or slope failure, and 3) rotation or base failure (Fig. 1). The effects of increased pore water pressure in soils were recognized in 1923 by Terzaghi in his development of the concept of effective stress, and he has applied the same principle to jointed rocks designating water pressure as cleft-water pressure.8 Cleft-water pressure in a rock slope reduces normal pressure on the plane of failure, thus reducing shearing resistance and resulting in slope failure. In the following discussion it is assumed that adequate drainage is supplied to prevent any build-up of water pressure. This is the first step in any program to establish maximum slopes. Ravelling: Ravelling occurs in rocks with low cohesion and entails the free movement of individual fragments ranging from single rock falls to running ground. Removal of lateral support wherever slope angle exceeds the angle of repose of the rock parti-

Jan 1, 1963

By Ronald M. Hays

The Duluth Gabbro Complex in Northeastern Minnesota possibly contains a significant domestic copper resource and the nation's largest nickel resource. Exploration has discovered large low-grade copper-nickel (Cu-Ni) deposits between Hoyt Lakes and the Boundary Waters Canoe Area (BWCA). The mining and processing of Cu-Ni will have environmental, economic, and social impacts. The purpose of this study is to relate major environmental, economic, and social considerations to various aspects of Cu-Ni extraction. An open pit and two underground (block caving and open stoping with backfilling) models were developed to generate information on the impact of Cu-Ni extraction. Important considerations having environmental, economic, and social impacts (luring various aspects of Cu-Ni extraction are identified and defined. These aspects are exploration, development, mining, beneficiating, smelting, transportation, and termination of operations. Considerations are grouped into the general categories of site, industrial, energy, climatic, resource, water, air emission, waste disposal, employee, tax and royalty, transportation, and community considerations. Cu-Ni extraction in Northeastern Minnesota presents major environmental, economic, and social risks. Decisions are required on trade-offs between adverse and beneficial impacts. The approach used in this study assists in assessing environmental, economic, and social impacts. It will aid in the examination of potential and projected short-term and long-term advantages and disadvantages and will aid in the development of Minnesota's Cu-Ni resource for the maximum benefit to society.

Jan 1, 1974

By M. Poirier, J. H. Mbouche

"The research question of the present work is the following: at which speed should a rotary sample divider operate in order to produce representative samples of iron ore concentrate? In order to solve this problem, the representativity of a rotary sample divider treating iron ore concentrate from Iron Ore Compagny (IOC) Carol Lake mine in Labrador City was studied in the laboratory of mineral processing of “CEGEP de Sept-Îles”. The rotary sample divider speeds tested are: 20, 40, 50, 60, 80 and 100%. The results show differences in both weight and particles sizes distributions with respect to the various rotation speed used. 20% has shown to be the speed that generates an almost normally distributed samples for both weight and particle size. As the speed of the rotary sample divider increases, the polygon of frequency for weight distribution progressively becomes a two modal distribution curve. 40, 50 and 100% speeds generate normal samples distribution curves with respect to particles size only. 60 and 80% are the speed to be avoided since they generate multiple modal distribution curves for both weight and particles size.IntroductionIn the mining industry, samples representativity is part of the key elements for management decisions. In fact, “Sampling provides vital information to plant operators, clients and geologists to profitably run and operate iron ore mines and plants” (Kevin Thorne et al. 2007). At the laboratory scale, several types of techniques’ are currently used to perform sampling. This include: grapping, alternate spading, quartering, riffles divider and rotating divider etc.. Among all these instruments, rotary divider is the most commonly used. Nevertheless, the usage of a rotary divider is not a guaranty for samples representativity since the results have shown to be related to running speed of this instrument. For the present research work, the idea is to use iron ore concentrate to quantify the representativity of a rotary sample divider. In other words, the research idea is to determine the speed at which a rotary sample divider produces representative samples while treating iron ore concentrate from Carol Lake mine. The present report will give an overview of the methodology used and the principal results obtained."

Jan 1, 2016

By Allison

During the 1980’s, laboratories opened throughout the United States to serve the analysis needs of a rapidly growing asbestos abatement industry. The samples analyzed were either collected during the abatement of known asbestos-containing materials or were suspect asbestos-containing construction materials. Many asbestos analysts received minimal training and used analytical protocols that were industry specific. False positives (reporting a sample as containing asbestos when none is present) went unnoticed or had minor repercussions. The mindset of the industry was to err on the conservative side – it would be better to identify a non-asbestos fiber as asbestos than visa versa. With growing public awareness of the health hazards of asbestos, other materials began to be tested for asbestos content. Rock and ores began to be tested for naturally occurring asbestos by these laboratories using the same protocols or an in-house protocol. Analysts were given no additional training and accreditation, in most cases, it was not required. With no consistency in sample collection, testing protocol or expertise in analysis, significant discrepancies in final results can be expected. If we further complicate this scenario with misidentification of naturally occurring look-a-likes for asbestos, expensive false positives are likely. To avoid the repercussions of misidentification of naturally occurring chrysotile asbestos from look-a-like fibers in rock and ores, correct sampling and analysis protocols with more stringent scientific diagnostic criteria are needed.

Jan 1, 2005

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By R. W. Pugh, D. G. Bellow

"This paper will describe how cultivator shanks are made in one company and how the manufacturing was studied with a view to increasing product consistency and reducing manufacturing cost. The product: which is used extensively in the agriculture industry, was analyzed to determine which geometric parameters optimized its design and whether there was justification for the great variety of styles and shapes that are available in the market. Finally, an extensive series of field trials were undertaken which showed that it is advantageous to the manufacturer to be better aware of the loads and forces that his product is subjected to by another industry.IntroductionStelco maintains a Research Group for its Western Region operations headquartered in Edmonton, Alberta. Because of the small staff, a location that is isolated with respect to its Burlington, Ontario centre and a diverse set of processes and products, a university relationship has developed which may be different from that which would be developed at a larger integrated Steel Works. This paper outlines the type of cooperative studies carried out by Stelco Inc. in Edmonton and the University of Alberta. .To meet the research needs covering a wide variety of steelmaking processes and steel products produced in Edmonton would require more staff and equipment than the sales volume in the West justifies. The gap is filled by cooperation with university personnel. This cooperation has provided these benefits to Stelco Inc.:• access to specialized test equipment and a trained staff to operate it; and• assistance from experts in the areas of product testing and problem solving.Moreover, the close proximity of the university to the plant allows frequent meetings and ensures that practical solutions are developed and implemented. A good example of the ongoing university I industry relationship developed is the joint work on improving cultivator shanks."

Jan 1, 1982

By H. R. Shell

Fluorphlogopite mica was synthesized from inexpensive and abundant olivine, clay, feldspar, and sand (plus K2SiF6). The raw materials were melted in crucibles and in an internal resistance electric furnace. The melts yielded >95 percent mica. The major difficulty encountered was incomplete settling of the highly dispersed ferroalloy. This problem was not completely solved. Reducing agents tried in melts of 300 to 400 pounds were carbon, silicon, and silicon carbide. Carbon slowly reduced the iron of the raw materials, with much fuming. Silicon apparently was oxidized ahead of the melting and was ineffective under the conditions obtained. By far the best reducing agent was silicon carbide. With silicon carbide, fuming did not occur and ionic iron content of the mica flake approached 0 percent. However, even with SiC, the highly dispersed globular iron did not completely separate from the mica portion. The fluorphlogopite made during this investigation should be suitable for metallurgical use. A byproduct ferroalloy containing about 5 percent nickel, 3 to 5 percent chromium, and some cobalt was obtained. Because of the highly dispersed metallic ferroalloy, the mica was not deemed suitable for electrical or electronic uses.

Jan 1, 1962

By J. M. Garcia

This paper highlights several management practices from the oil and gas industry to support the proposition that financial performance in the finite, non-renewable resource business relates more to upstream rather than downstream activities. Based on the analysis of nine oil and gas companies, this study supports a previous study involving fourteen mining companies that showed reserves growth is one of the main levers of value creation in mining. Interestingly, this study also finds that the oil and gas industry has been historically more profitable than mining. The reason, it is argued, is that oil and gas companies count on management practices that focus primarily on the upstream segments of the business, compared to the traditional downstream focus of mining. This paper delves into these ideas to conclude that what mining may need to improve its competitive advantage is a new organizational framework. Another conclusion is that the upstream management focus is vital not only for strategy formulation in the resource business, but also for policy formulation in economies based on the export of finite, non-renewable resources.

Jan 1, 2011

By R. J. Burgess

During World War II the shortage of ore revived interest in eastern iron deposits, among which -!2..c "Ile Massachusetts and Connecticut limonites. The Cheever mine, in the Richmond-Salisbury area of Massachusetts, was formerly a large producer of limonite ere. The Bureau of Mines investigated the lateral and downward extensions of the Cheever ore body, which was mined from about 1850 to 1892, by ap open cut 1,000 feet long and also by underground workings. even holes aggregating 1,723 feet, were drilled by the Bureau during the winter of 1943-44. They comprised three diamond-core drill holes, two churn-drill holes, and two rotary-drill holes. A geophysical survey of the Cheever mine area and adjoining ground was made in conjunction with the drilling program. Although this survey did not locate the limonite ore beds, the data were of considerable assistance in locating the limestone contact which forms the footwall of the ore beds. Drilling disclosed two beds of limonite with a heavy overburden of glacial till.

Jan 1, 1949

By Robert Harris, Peter Pheeney

"The Murray Brook gold mine operated from September 1989 to March 1991. Approximately 1.2 million tonnes of gossan were mined from an open pit and treated at a rate of 900 tonnes per day. The facility applied an agglomeration vat-leaching cyanidation plant for gold and silver recovery. The leached ore or tailings were rinsed of residual gold and cyanide and placed on an adjacent clay lined pad for storage and containment. A 50,000 tonne heap-leach demonstration project was constructed at Murray Brook in 1992 to recover copper and zinc from ore located in a sulfide-rich zone occurring beneath the gossan. The operation proved unsuccessful because of poor recoveries and low metal prices. The project terminated in the same year.A corporate decision was made in September 1999 to undertake complete and final reclamation of the Murray Brook site. Jacques Whitford and Associates Limited were contracted to develop the final reclamation plan and to assist the company in presenting the plan to the New Brunswick government for approval. The government approved the plan in January 2000. Two important reclamation issues were the mobility of mercury from the gossan tailings and the potential of acid mine drainage from exposed sulfides. The mine site is situated upstream of a productive river system, and the issue or impact of chemistry changes to the environment over the long term became an overriding factor in the development of the reclamation plan.A resource assessment of the gossan tailings in 1999 indicated an average concentration of mercury of 40 ppm. The mercury occurred naturally as the mineral cinnabar, but the exposure to residual cyanide (less than 10 ppm) over several years in the pile has likely caused much of the cinnabar to decompose into more soluble mercury forms. The reclamation plan specified the replacement of all sulfides to the pit followed by approximately 600,000 tonnes of gossan. To ensure “fixing” of the mercury, the gossan was replaced in compacted lifts and both the remaining pile and that replaced to the pit covered with available till and compacted. The reclamation work was successfully completed in September 2000 and the chemistry of the receiving environment will be monitored over a three-year period, after which the company expects to achieve walk away conditions."

Jan 1, 2001

The paper deals with the results of dynamic tests carried out on a range of surface support liners consisting of combinations of mesh (various types), shotcrete, and wire rope lacing. The testing was carried out over the period 1993 to 1998. The dynamic testing method made use of drop weight impact loading of test samples which attempted to simulate realistic in situ conditions, and the range of loading imposed was equivalent to small to severe rockburst conditions. The results of the testing provide quantitative data, in the form of input energy, which is relevant for support design and for the choice of support types appropriate for situations in which significant mine-induced seismicity occurs or is expected to occur. In addition to the wire mesh and shotcrete liner systems tested, estimates of energy capacity are made for other, untested, systems.

Jan 1, 2001

By Joseph Clare, Elizabeth Anderson, Mike McGinley, Ron Hines, Judy Cochran

The South Lake Union Pipelines contract for King County Wastewater Treatment Division and Seattle Public Utilities in Seattle, Washington included three 1.8 m (72-in)inside diameter microtunneled pipeline segments totaling about 793 m (2,600 lf).Tunnel alignments were within street right-of-way of heavily traveled urban roadways. Project challenges recognized in the design included: high groundwater levels; contaminated soil and groundwater; variable soil conditions, including fill; and timber piles and other obstructions remaining from historic land uses. The tunnels were built using a Lovat MTS Microtunneling machine, beginning in spring 2003. Conditions encountered during construction presented additional challenges beyond those anticipated in the design process, and were successfully addressed by the owners, designer, and construction management consultant all working with the contractor. Problems included highly variable soil conditions, cracking of reinforced concrete pipe joints during pipe jacking, a timber pile trestle uncovered during shaft construction, and obstructions encountered in the second and third microtunnel runs.

Jan 1, 2005