Search Documents

By A. H. Onur

Many factors govern the size and shape of an open pit, and these must be properly understood and used in the short and long-term planning of any open pit and quarrying operation. The importance of each factor will depend on the particular project, but the geology, grade, and localization of mineralization, extent of the deposit, topography, property boundaries, production rates, bench height, pit slopes, road grades, mining costs, and cut-off grades are key elements of open pits. This paper discusses the work done on the above parameters in order to provide an optimal production plan for a limestone quarry and clay deposits that provide raw material for a cement factory in Turkey. Soke cement factory has 1 400 000 tons of clinker capacity and is located on the western part of Turkey, in the province of Aydin. It is one of the largest facilities in the cement sector in terms of capacity, and it has a large advantage over facilities because the location of the factory was chosen to obtain the raw materials necessary for cement production within very short distances. However, the old reserves that supplied limestone to the factory had been reported to have run out, and therefore new limestone reserves in the same province have been investigated over the years by experienced geologists. From surface samples, high MgO content was reported in the neighbourhood of limestone formations with high dolomatization; hence, other alternatives were taken into consideration. One alternative with better chemical composition had been found 24 km away from the factory, but the haulage cost of limestone was unacceptable for the factory due to high diesel prices in Turkey. The maximum allowable MgO content in the pre-mix feed to a rotating furnace is 2.5% MgO content in pre-mix from both limestone and clay deposits. The clay deposits belonging to the cement factory have higher MgO content than the limestone deposit, and therefore this quality problem was taken into consideration first, instead of transporting material from 24 km away. This study gives the details of work done to evaluate both the clay and limestone deposits, statistical analysis performed on core samples taken from drill holes, mathematical modelling for both sites, and most importantly of all, in-pit homogenization work that reduced the pre-mix MgO content. As a result of this study, the profitable limestone quantity has been improved in order to serve the cement factory over a projected 25 additional years without using any material from the close deposit.

Jan 1, 2008

By A. Barba, M. P. Gómez, F. Puertas, M. Palacios, M. F. Gazulla, S. Martínez-Ramírez, I. García-Díaz

"The present study explores the reactivity and burnability of cement raw mixes containing fired red or white ceramic tile wastes or combinations of the two as alternative raw materials. The results showed that the new raw mixes containing these wastes are technically viable. The reactivity and burnability of the new raw mixes have been evaluated; confirming very good results when the particle size of wastes was less than 90 µm. The chemical and mineralogical compositions of the new clinkers were comparable to clinker manufactured with conventional raw materials. The mix of red and white ceramic tile waste was found to perform as well or better than each type of waste separately, a promising indication that separation of the two would be unnecessary for these purposes.IntroductionPortland cement clinker production consumes large amounts of energy (850 kcal/kg clinker) and has a considerable environmental impact. This involves massive quarrying for raw materials (limestone, clay etc), as it takes 1.7 tonnes to produce one tonne of clinker, as well as the emission of greenhouse and other gases (NOx, SO2, CO2) into the atmosphere. Around 850 kg of CO2 are emitted per tonne of clinker produced.The cement industry is looking for solutions to these problems, to attain sustainability and comply with the Kyoto Protocol commitments [1,2]. For that reason, experimental ways are being explored to develop cements whose manufacture is less energy-intensive, less damaging to the surrounding environment and with lower tendency to emit polluting gas. One of the reach this objective is the use of industrial waste and by-products as alternative materials for cement manufacture. Such alternative materials may partially replace fuel [3,4], conventional raw materials [5-8] or clinker in the final composition of the cement [9]."

Jan 1, 2008

By Lawrence J. Froisland

To aid in minimizing adverse environmental impacts of mining and mineral processing, the Bureau of Mines studied changes in soil characteristics in topsoil stockpiled during mining operations. Topsoil stockpiles in arid areas of New Mexico, Utah, and Wyoming were sampled over a 1- to 8-yr period to determine any changes in physical, chemical, or biological parameters in the top 15 ft of soil. Parameters examined in this study included soil moisture, pH, electrical conductivity, and cation exchange capacity; total nitrogen, organic carbon, carbon to nitrogen ratio, extractable potassium, and soluble phosphorus levels in the soil; general levels of bacteria activity in the soil; and productivity of the soil as measured by shoot yield in growth tests. Data were analyzed by multiple linear regression to determine possible effects of stockpile age and depth. Bacteria population counts, used as an indicator of goner l bacterial activity, was the only parameter found to be significantly correlated with stockpile age and depth at more than one site. Bacterial activity increased with depth at the two sites where it was measured. Activity increased with age at one site and decreased with age at the second. Significant changes in soil pH, electrical conductivity, and moisture were significantly correlated with stockpile age and depth at single sites. This study did not show significant, consistent deterioration in soil characteristics or growth yield of topsoil stored in stockpiles.

Jan 1, 1987

The 1965 Lignite Symposium, the Louth in a series and the third sponsored by the University of North Dakota and the Bureau of Mines, was held at Bismarck, N. Dak., on April 29-30, 1963. These symposia provide a forum for those interested in the technology and utilization of solid fuels, especially lignitic coals. As part of the meeting, a 200-mile field trip was taken including; inspection of (1) the 200-megawatt, pulverized lignit-fired Leland Olds plant of Basin Electric Power Cooperative, under construction near Stanton, N. Dak.; (2) the site of the Glunharold mine of the Truax-Traer Coal Co., Division of Consolidation Coal Co., where a wheel excavator was being assembled; (3) the operating Beulah mine of Knife River Coal Mining Co., subsidiary of Montana-Dakota Utilities Co., near Beulah, N. Dak.; and (4) the 400-megawatt, hydroelectric Garrison Dam powerplant, near Garrison, N. Dak.

Jan 1, 1966

By G. H. Keith

Electrowon tungsten powders were investigated with respect to consolidation, fabrication, and mechanical properties. Sheet, 0.03 inch thick, was produced and its tensile strength measured between 250° and 1,935° C. The large particle size of electrowon tungsten effectively precluded sintering to a density sufficient to allow hot working to sheet or bar. The powders were consolidated by die pressing to 70-percent density, sheathing in molybdenum, and high-energy-rate extruding to either round or sheet bar of 100-percent density. The material was then rolled conventionally to sheet. The mechanical properties of the sheet prepared from the electrowon powders compared favorably with those reported in the literature for sheet prepared from commercially produced hydrogen-reduced powder.

Jan 1, 1970

By Steven I. Majtenyi

There is a growing interest among transportation planners to make more use of the subsurface to preserve the landscape and make transportation more efficient and economical. At the present time, utilization of the underground for transportation facilities is severely restrained by the adverse environmental impact and high construction costs. However, recent studies performed by the United States Department of Transportation indicate that, in spite of such problems, the volume of underground construction has significantly increased during recent years and projections point to continuation of these trends(1). It is estimated that the total volume of transportation tunnel construction will exceed $4 billion in this decade. This level of Investment justifies a significant research program. Due to the common interest in transportation tunnels and to the similarities of problems encountered during their construction, the tunneling research activities of the Federal Highway Administration (FHWA) are closely coordinated with the programs other agencies of the U. S. Department of Transportation DOT); specifically, the Federal Railroad Administration (PRA) and the Urban mass Transportation Administration (UMTA). The FHWA is responsive to the particular needs of these agencies but will benefit from the research results obtained also. In 1971, the Office of Secretary, DOT, initiated plans for an overall coordination of the DOT, FICA, UMTA, and FHWA tunneling research activities. The objectives of this effort have been to reduce tunneling costs by 30% and to increase the rate of excavation by 200% within 10 years. This coordinated program was developed and promoted during 1972 and 1973 by Dr. Eugene L. Foster, at that

Jan 1, 1974

By Tae-kyeong Yeu, Jong-Choi, Cheon-Hong Min, Hyung-woo Kim, Jae- Won Oh, Sup Hong, Minuk Lee, Sung-Soon Kim, Chang-Ho Lee, Ki-Young Seong

"Collecting mineral resources from the seabed using a seafloor crawling robot is the firststep in the mining operation. The second-step is lifting the collected ore up to the water surface. For lifting through a riser pipe, prevention of pipe clogging (flow assurance) and economic and eco-friendly up-transferring is of the utmost concern.During collection of mineral ores, the production rate can be highly variable because of the variability in the distribution of the mineral deposit, variations in seafloor topography, fluctuations robot speed, and variations in performance of the mining robot, etc. Direct transfer of the collected ore to the riser pipe might cause unpredictable and serious problems such as over-loading of the lift pump, reduction in the life of the equipment, pipe clogging, severe increase of down-time, critical damage of equipment, further propagation of damages, and total failure after all.As a counter measure to these potential problems, a buffer station has been adopted, which is capable of storing the collected ore for a certain time and simultaneously regulating the transfer of the ore into the riser pipe. A pilot buffer has been developed by KRISO/KIOST (see Fig. 1)."

Sep 1, 2014

By R. Ward Stahl

Fire is still a scourge of the mining industry, although many precautionary measures have been and are being taken to reduce the incidence of fires and to combat them. Generally, the success of fire extinguishment is directly proportional to the speed of attack, and the speed of attack in turn is dependent upon the availability of materials and trained personnel. Preparations for firefighting are frequently neglected because they are considered emergency needs and do not contribute directly to coal production. Fire incites panic--a fact often overlooked--but such chaos can be minimized by training people in the use of equipment and procedures. Heat, smoke, and fumes hamper the approach to a fire; however, a relatively new technique of attacking fires with high-expansion foam may well contribute greatly to firefighting. The foam is transported to a fire and used at a considerable distance, thus permitting the firefighters to work more safely.

Jan 1, 1962

By W. Tom Witherspoon

Many Engineers are skeptical and cautious about skin friction factors for the portion of drilled piers where temporary casing is used. This has led Texas engineers in many cases to eliminate skin friction values for the cased section, which necessitates deepening the drilled shaft to compensate for the loss in the cased section. This paper has provided field test data that supports inclusion of skin friction in the temporarily cased hole section as a contributing factor in total axial capacity as comparable to open hole shafts of the same diameter. Reasons for the resultant friction values are provided including; remolding of the cased clay section and the increased pier circumference necessitated by the oversized casing required for adherence to the engineers shaft diameter specification.

Jan 1, 2009

By J. L. Holman

The Bureau of Mines, at its Rolla Metallurgy Research Center, has devised methods for separating and reusing the major portion of waste plastics discarded in urban and industrial refuse. Waste plastic concentrates from a local collection drive, recycling center collections, urban refuse pilot plants, and the secondary metals industry were separated into three major thermoplastic families--polyolefins, styrenes, and vinyls--based on differences in density using a Bureau-designed sink-float-elutriation hydraulic separator. Other separation methods and systems such as air classification, jigging, liquid media, screening, and electrostatics were studied. Vinyl plastics contain up to 50 percent HC1. It was found that over 90 percent of the HC1 in vinyls can be recovered as usable hydrochloric acid by pyrolysis at 350° C. The remaining pyrolysis products which had heats of combustion in excess of 12,000 Btu/lb, could become valuable as a future source of energy. A characterization study conducted on eight chopped wire insulation wastes from secondary copper and aluminum processors showed that most wastes contained 2 to 7 percent residual metal and large percentages of vinyl. The residual metal content of some of these wastes was lowered to 0.1 percent and the vinyl portion segregated using various separation techniques. The research also suggests ways in which reclaimed thermoplastics may be fabricated into useful products.

Jan 1, 1974

By P. H. Carr, G. G. Marino, K. A. Patel

Extensions to a correctional institution at Wabash Valley, Indiana, required development over abandoned coal-mine workings, at 90 m depth, where subsidence was possible at surface. Backfilling of the flooded mine in critical areas was determined to be the most cost-effective method of limiting the risk of damage to the buildings. Containment grout was first placed in selected entries and cross-cuts of each mine area; the remaining volume was then filled with a readily flowing infill grout. Where a high proportion of an area was taken up by rubble, calcium lignosulphonate was used as a retarder and plasticiser to increase penetration. Grout movement was monitored from adjacent boreholes with an electrical resistivity probe during grouting, while after the work was finished core samples were obtained from verification holes drilled in the backfilled areas

Jun 19, 1905

By S. Z. Pethö, H. Yilmaz

South Deep Mine is currently undertaking numerous voidfilling projects using low strength aerated cement products. Representative samples from one such site, were taken and tested for the load deformation behaviour under uniaxial loading conditions. The process of sample collection, laboratory preparation and testing are explained in detail. The results of testing were analyzed and the critical aspects pointed out as a design consideration to be implemented as part of the quality control and assurance program. Design aspects and underground application of the aerated cement product are discussed for the particular site on 58 level SV1. A simple instrumentation has been designed and installed to enable monitoring of any future movements in this area. A quality control and assurance process has been formulated enabling all aspects of the support installation in this excavation to be signed off.

Jan 1, 2003

By R. O. Burt, D. J. Ottley

"SYNOPSISRecent developments in the use of the Bartles-Mozley table and the Bartles CTS screen are described for the gravity preconcentration of fine heavy mineral and metal particles present in low grade pulps. The B-M table is a relatively new device used for the recovery of particles of up to 100 micron size down to 5 microns or in the case of gold and platinum, down to 1 micron. The CTS screen is a wet screening device used for feed preparation ahead of the Bartles-Mozley table and will size effectively down to about 300 mesh. Results and operating data for a number of different materials are given including outline flowsheets; the effects of the major variables on the performance of the table are briefly discussed. The potential of the B-M table to treat a variety of different ores, coal, tailings, and waste products are considered. The utilization of the B-M table in association with other unit processes to improve overall results as well as to improve the economics of design and performance of plants are also mentioned.INTRODUCTIONA number of new gravity concentration devices have been developed in recent years for the recovery of fine heavy mineral and metal particles but for reasons which include low capacity, high capital or operating costs, competition from other and better processes, the absence of simplicity or reliability in operation etc., only a few which include the Bartles-Mozley table, have been proved to be of commercial application.The name of the machine is derived from the inventors name, Richard Mozley, who developed the B-M table at the University of Bristol in England. The table was subsequently taken up and patented, world-wide, by the National Research Development Corporation a British government agency. An exclusive license to manufacture the table was granted by NRDC to Bartles (Carn Brea) Ltd. in Cornwall, England."

Jan 1, 1973

Experiments on High Efficiency Separation of Mixed Plastic Wastes by Vortex-Tube Separator

Sep 13, 2010

Particles of a complex nickel sulphide concentrate (containing pyrite, pyrrhotite, pentIandite, and violarite as the major mineralogical constituents) were entrained in a stream of hot gas the temperature of which was varied from 500 to -1000°C. Chemical analysis of the particulates collected from the furnace was used to detect the rapid change in sulphur content which accompanied the ignition temperature jump. X-ray diffraction analysis was used to characterize the oxidized material.These techniques showed that ignition was dependent on the mineralogical composition and occurred over the temperature range 500-900°C. Pyrite ignited first in the range 500-600°C; pyrrhotite was the least reactivemineral and required temperatures in excess of 800°C for ignition. The nickel minerals <pentIandite and violarite decomposed before ignition and ignited at temperatures intermediate to those required for the pyrite and pyrrhotite. The ignition temperature for the pyrite was found to be independent of particle size and concentration of oxygen in the atmosphere.Ignition temperatures determined by the simulated flash smelting method were compared with the results of differential thermal analysis (DTA) measurements performed on the same concentrate. Temperaturesdetermined in the DTA test as corresponding to the start of exothermic activity were shown to be at least 100°C below those determined by the simulation test.

Jan 1, 1978

By W. J. Errington

The Isasmelt process was developed at Mount Isa Mines Limited in Queensland, Australia in collaboration with CSIRO, the Australian Government research organisation. Originally developed for primary lead smelting, culminating in the construction of a 60,000 tonnes per annum lead smelter at Mount Isa, this technology now also provides a major part of the current 200,000 tonnes per annum copper smelting capacity at Mount Isa. A programme is now in place to expand copper production to 250,000 tonnes per annum. The technology has also been applied to secondary lead smelting at Britannia Refined Metals, a MIM subsidiary company, where a 30,000 tonnes per annum lead plant based on battery scrap feed has been operating since 1991. Mount Isa Mines Limited decided to license the technology in1988, and copper smelting plants utilising Isasmelt technology are now operated by Cyprus Miami Mining Corporation in the USA and by Sterlite Industries in India. In addition, the technology was adopted by AGIP for smelting copper/nickel concentrates in Australia. Union Miniere are currently constructing an Isasmelt furnace to smelt and convert copper-containing materials at their plant at Hoboken in Belgium. This paper discusses these developments and also some likely future developments which include the application of the technology for continuous copper and nickel converting and applications in the treatment of zinc-containing residues.

Jan 1, 1997

By T Do, J Siliezar, M Larson

With the expansion of magnetite projects in Australia has come the opportunity to take advantage of newer technologies that were not necessarily available when the magnetite industries of North America and Europe were maturing. One of these technologies is the IsaMill, originally developed for the economic treatment of ultra-fine grind (UFG) duties of Mount Isa Mines. As understanding of the IsaMill has increased, so too has the ability to process coarser feeds while maintaining the same energy efficiency advantage and tight product size distribution that originally made the IsaMill so attractive. In the case of magnetite the hard non-elastic ceramic grinding media is ideally suited to the grinding duty when compared to steel grinding media. The centripetal separator and naturally steep product size distribution curve provide a mill discharge that maximises the critical concentrate grade. This paper analyses the effect of the IsaMill grinding technology on the full-scale Ernest Henry Mine (EHM) magnetite operation along with pilot and lab scale demonstrations of optimisation. Issues encountered and the solutions to maximise the mill throughput and quality are examined in an effort to promote better understanding across the industry. CITATION:Larson, M, Do, T and Siliezar, J, 2013. Enhancing magnetite returns - the benefits of IsaMilling, in Proceedings Iron Ore 2013 , pp 411-416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Özgür Bezgin

This paper presents observations on the installation of drilled shafts from two construction projects and an academic study with experimental and analytical parts. The construction projects involved the use of pressurized drilling methods. The experimental part of the academic study involved the use of the auger drilling method. The analytical part of the academic study investigated the effect of drilling methods on the soil-structure interaction and the behavior of drilled shafts under lateral loads. The concept of ?free-length? is introduced for the lateral load design of pressure-drilled shafts that are thought to be fully embedded within a soil media. The academic part of the study presented herein was conducted in Rutgers, the State University of New Jersey.

Jan 1, 2009

By D. C. Panigrahi

Extensive field studies have been carried out to investigate the pillar fire problems in one coal mine in India. A Thermal IR gun and a Thermovision camera have been employed for thermal scanning to assess the state of heating in selected pillars. Special sampling set-ups have been designed to collect gas samples from the holes drilled into the selected pillars and the multigas detector is used to analyse the composition of samples in situ. In order to predict the spontaneous heating in coal pillars, different gas ratios have been calculated and it has been observed that some of the established gas ratios, viz. Graham?s ratio, Young?s ratio etc. have resulted in negative values in samples containing high amounts of methane. The modified gas ratios have been proposed which will be useful for predicting the pillar fires. These ratios may also be used for assessing the condition of fires in sealed-off areas.

Jan 1, 2004

Platinum-group minerals (PGM) are recorded from a number of localities along theWaiau River, western Southland, and the south coast of the South Island, New Zealand. At each locality, small amounts of PGMs were recovered as by-products of historical gold mining operations. During the period 1890-1950 an estimated 1000-2000 oz. of æplatinumÆ were recovered from the region, the only area within New Zealand where PGM have been commercially exploited. The PGM suite of southern New Zealand consists of Pt-Fe alloys, IPGE (iridium subgroup, platinum-group elements) alloys, sperrylite (PtAs2), cooperite (PtS) and braggite ((Pt,Pd)S). The composition of Pt-Fe alloy exhibits considerable variation and two compositional populations are recognised. Some Pt-Fe alloy grains are chemically zoned. Iridium is the most abundant IPGE alloy phase and often contains considerable Pt, in contrast to osmium and ruthenium alloys. Cooperite and braggite grains are characterised by extremely low concentrations of Ni.   Exsolution of osmium and iridium from Pt-Fe alloy and Pt-Fe alloy from iridium is observed Several PGM host mineral inclusions which vary from single to poly-phase, display rounded to equant outlines and range in diameter from greater than 100 ¦m to less than 5 ¦m. Olivine and Ni-sulphide inclusions are only present within IPGE alloys. Pt-Fe alloy, cooperite, braggite and sperrylite host Cu-Fe sulphides, a wide variety of PGM, clinopyroxene, amphibole, magnetite and plagioclase within inclusions. Sperrylite also hosts Pd bismuthiotellurides, gold and several potassium-rich silicate phases. Similarities in inclusion phases and mineral chemistry from several localities suggest that the PGM are derived from a single (as yet unidentified), probably calc-alkaline magmatic source. This source is situated somewhere along the margins of the western Southland sedimentary basin where PGM liberated by erosion are transported down the Waiau River and dispersed eastwards along the coast by strong longshore currents.

Jan 1, 1995