Search Documents

By M. W. Kennedy

Prediction of the thermal duties of copper coolers in freeze lined furnaces is challenging. Where copper coolers are immersed in liquid slag the heat transfer is often defined by a natural convection cell immediately adjacent to the wall, in the absence of other factors producing forced convection. Slag coolers are typically not fully immersed, slag temperature, liquidus and superheat can vary, and bath levels may change significantly with batch tapping, leading to substantial variations in radiation heat fluxes. Radiation heat transfer is discussed with reference to the non-obvious impact of slag liquidus on radiation losses in the exposed cooler sections. Reference is made to literature and the results of analytical and FEM models.

By C. A. Pickles

Microwave processing is a relatively new technology that has been successfully applied in a number of industries. However, in the field of metal extraction, there is a paucity of success, despite considerable hype in the early years. Increased reaction rates, lowered reaction temperatures and higher energy efficiencies were some of the advantages claimed. Even with over almost two decades of research and some pilot plant studies, microwave metal extraction remains essentially a laboratory technique. In this paper, the research performed over the last few decades will be reviewed and some reasons for the lack of success in developing microwave metal extraction processes will be discussed. Based on the knowledge gained from these experiences, a more informed view of microwave heating can lead to the realization that there is still some untapped potential for this heating technique in metal extraction processes.

By Anja Pfennig, Axel Kranzmann, Sabrina Schulze

The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, C02-corrosion of the injection pipe steels has to be given special attention when engineering CCS-sites. To get to know the corrosion behaviour samples of the heat treated steel 1.7225 42CrMo4, used for casing, and the stainless injectionpipe steel 1.4034 X46Cr13 were kept at T=60 °C and ambient pressure as well as p=lOO bar for 700 h - 8000 h in a C02-saturated synthetic aquifer environment similar to possible geological on-shore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the C02 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite F eC03 in both types of steel.

Jan 1, 2013

By Zhucheng Huang, Yuanbo Zhang, Kecheng Zhang, Guanghui Li, Tao Jiang

"With rapid development of Iron and Steel industry, plenty of metallurgical dusts and sludges are generated, which have not been effectively utilized because of their poor hydrophilicity and bad ballability. Agglomeration and roasting of metallurgical dusts & sludges with a new-type composite binder are studied in this paper. The results indicate that the dosage of the new binders can be decreased to 2.5 wt% from 3.5 wt% when using the wet-grinding process. Under the optimal conditions of briquetting pressure 2070 N/cm2, briquetting moisture content 13 wt%, roasting temperature 1000 °C and roasting time 40 min, the qualities of the green, dry and roasted briquettes meet the requirements of the industry production. The finished products have the compression strength of more than 2000 N/cm2, which can be used as high-quality burdens for blast furnaces.IntroductionWith rapid development of Chinese Iron & Steel industry, there are more and more serious resource shortage and environmental pollution existing. Converter sludges, containing 30% ~ 40 wt% moistures, are typically difficult for recycling [1]. Foreign processing technologies for sludges treatment are relatively advanced including cold-bonded agglomerates for blast furnace, RHF reduction for the dusts and sludges with high content of Zn and Pb, smelting and reduction. Domestic iron and steel companies use a small amount of sludges in sintering. However, the sludges have the characteristics of high moisture and containing harmful impurities, which directly affect the sintering mixture permeability and product quality [2-5]. There are also other technologies such as production of metallized pellets, cooling agents for steelmaking, etc [6]. All of these deficiencies and applied are not in large-scale."

Jan 1, 2011

By J. Schmidl

In non-ferrous metallurgy the service life of refractory materials typically ranges from several weeks up to three years or more and is strongly dependent on operating conditions. To support our customers with the most viable refractory solution for their needs RHI Magnesita follows a structured approach of thermo-chemical calculations, experimental evaluation from lab scale up to industrial field tests and post-mortem analysis of used refractory materials. This paper will give an overview of the RHI Magnesita refractory selection process and the most recent developments of the experimental setup for the so called HF-IF test. This is a dynamic corrosion test that allows to determine fundamental properties of different refractory material types under process conditions subjected with respective customers process materials. The HF-IF experimental procedure is an excellent tool to simulate refractory wear in industrial processes, diminishing risks associated with plant trials and support decision making to choose the optimal refractory solution for the customer.

By Dominik Hofer

A broad spectrum of tantalum containing input materials can be processed for the production of synthetic tantalum concentrate (“SynCon”). The use of these low grade substances offers a secure alternative to mining of coltan in Central Africa. SynCon is produced in a multi-stage pyrometallurgical process, wherefore the melting behaviour of slags presents an important factor especially regarding the energy consumption and its optimisation. The characteristics of a slag comprising mostly Al2O3, CaO, SiO2 and MgO are influenced by the amount of other oxidic constituents which enfolds the main focus of this study. A hot stage microscope serves for the investigation of the slag behaviour in a temperature range from 1000 to 1600 °C under reducing atmosphere (CO/CO2 gas). The experimental results are compared with thermodynamic calculations (FactSage) to get a better understanding of the process.

By Xuan Cheng

The electrochemistry of sulfide mineral flotation is reviewed with particular emphasis on galvanic interaction among minerals and grinding media, and its relevance to flotation of complex sulfide ores is discussed. Surface alteration due to galvanic interactions among chalcopyrite, pyrrhotite and mild steel is analyzed in terms of voltammetric and chronoamperometric studies on individual minerals and through galvanic current measurements in 2- and 3- electrode combinations. The results are related to laboratory flotation behaviors of chalcopyrite-pyrrhotite mixtures simulating copper-nickel bearing Duluth gabbro.

Jan 1, 1993

By Aurelian Buzaianu, Cristian-Aurelian Popescu, Gabriela Popescu, Petru Moldovan

"A lot of scraps result in processing of composite materials which contain metallic phases that can be recovered and used again in different field. Considering this point of view the aim of the paper was to separate and recover aluminum from aluminum matrix/graphite composites. The separation and recovery of aluminum alloy from aluminum alloy/graphite composites was done by treatment with halide molten salts. As halide salts were used flux tablets that collect the ceramic particles in dross. After dross separation, was used filtration in order to separate the aluminum matrix from the other impurities.Samples from the recovered alloy were analyzed using chemical analysis, optical and electron microscopy, as well as X-ray diffraction. The desired composition of the aluminum alloy obtained from scraps could be reached by some addition of metals to the metallic phase. From optical microscopy it was obvious that the structure of the aluminum alloy obtained after composite reclamation consists large particle of silicon, eutectic, a-Al solid solution and other phases like Fe, Si, Mg and Ni, or some compounds like CuAl2. 1. IntroductionThe research on the recycling and reclamation of metal-matrix composites (MMCs) becomes active to preserve the natural environment, as environmental requirements become stricter, to save energy, and to reduce garbage. In case of recycled aluminum alloy ingot the production energy is about 3 pct of that of the new ingot. This evidence strongly supports the necessity to recycling of aluminum alloys. Among aluminum alloys, metal matrix composites have high strength and elastic modulus, and also good were resistance. These materials have been developed to meet the demand properties which exceeds that of the ordinary materials, and to save energy."

Jan 1, 2008

By G. Fazel Jahromi

Enargite, known as one of the major arsenic containing copper minerals, with approximately 19% arsenic, introduces challenges to typical processing options. In most hydrometallurgical processing methods, arsenic remediation occurs after the copper recovery in an autoclave or in a stepwise neutralization process. In this study, the in situ precipitation of scorodite was investigated during an atmospheric leaching process in the presence of carbon-based catalysts and chloride media. The effective parameters of initial ferric addition, temperature, catalyst addition, and oxygen sparging rate were studied and the ferric behaviour was monitored during the scorodite precipitation. The most influential parameters on efficient scorodite precipitation are found to be: initial ferric addition, catalyst to concentrate ratio, and temperature. A 99% scorodite precipitation yield was achieved in this process.

By R. J. Wesely

The paper describes the various methods which are currently being used or considered to refine gold and silver. These methods are then compared on a technical and economic basis. Conclusions are drawn on the factors which might influence the choice of process for different feed stocks and economic constraints

Jan 1, 1990

By Manoj Kumar, Vinay Kumar, Nikhil Dhawan, Manish Wadhwa

"Electronic waste (e-waste) is a collective name given to discarded electronic devices such as Television, Cellular Phones and Personal Computers. Among the heterogeneous metals present in the e-waste are the base metals: copper, aluminium, nickel, tin, zinc, iron and precious metals: gold, silver, palladium, platinum apart from several hazardous and halogens metals. Hence there is a need to recover these metals from electronic scrap by recycling and then re-use, which can meet large amount of metals demand. Hydrometallurgical processing was employed for the recovery of metals from television printed circuit board (TV PCB). Different lixiviants such as hydrochloric acid, Sulphuric acid, and nitric acid were used to understand the dissolution behavior of copper, iron and lead present in the TV PCB. Effect of increasing concentration of nitric acid was also studied. Selective recovery of tin over 95% in the form of tin oxide was precipitated. The precipitated tin oxide was identified by X-ray diffraction technique. Tin oxide of purity more than 99.9% was obtained.IntroductionThe electrical and electronic industries comprising computers, television, mobiles, etc, which are manufactured utilizing printed circuit, boards, capacitors, resistance, soldering material etc. During production, at the end-of service life and degradation due to the advanced version with latest features generate valuable metallic and non-metallic constituents. European Union Council on waste electrical and electronic equipment (WEEE) has classified these into different categories as listed in Table 1 [Streicher-Porte et al., 2005]. Among these the information technology, telecommunications and consumer equipment constitute electronic waste (e-waste) [EC, 2002]. Almost all e-waste consists of an integrated part of printed circuit boards which is a valuable source of several metals such as copper, tin, lead, aluminium, iron, silver, gold, platinum etc. [Relay et al., 1990]."

Jan 1, 2008

By Jun Enriquez

Kennecott Utah Copper aims to extend anode furnace campaigns to more than three years. As part of that goal improvements are sought on anode-furnace tuyere-area refractory performance. Kennecott and Praxair developed high pressure nitrogen refining for the Oxidation Stage which shortened anode furnace fire refining cycles by up to two hours per cycle. Future developments include optimizing the Reduction Stage’s steam-gas reforming and achieving coherent jet tuyereless refining.

By Runsheng Xu, Haiyang Wang, Pengcheng Zhang, Tengfei Song

Semi coke, a byproduct in the chemical industry, is a new fuel for blast furnace injection in China. In this study, semi coke and bitumite were milled into different size, ranged from 0.147mm to under 0.074mm. The content of volatile matter and ash, which affect the combustibility of semi coke, were measured using muffle furnace. The mixture, in which the proportion of coal in different sizes changed, was blend by semi coke and bitumite with different size. Activation energy calculation and the comprehensive combustion characteristic index of all kinds of blends was also discussed. The result obtained by Thermogravimetry –Derivative Thermogravimetry curves indicates that the smaller the size of mixture is, the lower for the characteristic temperature, and the better for its combustibility, Semi coke can be a substitute for anthracite in blast furnace injection.

Jan 1, 2015

By Ravi S. Bellur-Ramaswamy, Daniel A. Tortorelli, Robert Haber, Nahil A. Sobh

We optimize continuous quench process parameters to produce functionally graded aluminum alloy extrudates. To perform this task, an optimization problem is defined and solved using a standard nonlinear programming algorithm. Ingredients of this algorithm include 1) the process parameters to be optimized, 2) a cost function: the weighted average of the precipitate number density distribution, 3) constraint functions to limit the temperature gradient (and hence distortion and residual stress) and exit temperature, and 4) their sensitivities with respect to the process parameters. The cost and constraint functions are dependent on the temperature and precipitate size which are obtained by balancing energy to determine the temperature distribution and by using a reaction-rate theory to determine the precipitate particle sizes and their distributions. Both the temperature and the precipitate models are solved via the discontinuous Galerkin finite element method. The energy balance incorporates nonlinear boundary conditions and material properties. The temperature field is then used in the reaction rate model which has as many as 105 degrees of- freedom per finite element node. After computing the temperature and precipitate size distributions we must compute their sensitivities. This seemingly intractable computational task is resolved thanks to the discontinuous Galerkin finite element formulation and the direct differentiation sensitivity method. A three-dimension example is provided to demonstrate the algorithm.

Jan 1, 2001

By Shu Yamaguchi

The behavior of halide impurities in pyrometallurgical processes such as Wealtz kiln and MF process has been discussed based on the thermochemical data and the reported data of PbO activity in PbCl2-PbO melts. The role of PbCl(g) has been estimated to be significant in the chloridization evaporation reaction. From reported data on the PbO activity in PbC12-PbO melts, activity of PbCl2 has been calculated by the numerical integration of Gibbs-Duhem equation, and the stability domains and the composition of the liquid phase as well as the vapor pressure of PbCl2 have been estimated as functions of log P2HCI/PH2O and temperature. From the discussion of the path during cooling process on the log P2 HCI . PH2O vs. temperature diagram, the authors proposed a possible dechioridization process that utilize water vapor as a dechloridizer for the direct precipitation of PbO from gas phase.

Jan 1, 2003

By A. Rios

ENAMl's Paipote Smelter commenced operations in 1951. At present, it processes 230,000 tonnes/year of green feed in a conventional smelter, which comprises one reverberatory furnace, two Hoboken, one Peirce-Smith converters and one rotary anode furnace. The feed is composed of 83% copper concentrate and 17% metallic copper precipitates, which results in a feed average grade of 32% of copper content. The final products are 75,000 tonnes/year of copper anodes and 48,000 tonnes/year of sulphuric acid. At present, the plant is undergoing a modernization to expand the smelter capacity to 300,000 tonnes/year of green feed and increase the sulphuric acid production to 100,000 tonnes/year. This will be achieved with the installation of an El Teniente Converter and an expansion in the acid plant. The work began in November 1991 and is scheduled to be in operaton by March 1993. The paper provides an overview of the modernization plans and results achieved to-date.

Jan 1, 1993

By Scott R. Giese, Lucas Dix

"Recently, there is a growing trend in the aluminum foundry industry to develop· improved melting and casting processes to produce lightweight, high-strength, and thin-wall castings for the aerospace and transportation industry. One casting method that has demonstrated industrial potential for producing clean, thinwall castings is vacuum-assisted, counter gravity casting. This process has the benefit of expeditiously and quiescently filling the casting cavity with a dramatic reduction of furnace related and reoxidation inclusions. Additionally, lower casting temperatures can be utilized because the application of vacuum during filling overcomes the resistive internal cavity pressure resulting in a finer, as-cast microstructure. The paper explores and discusses the processing and design conditions in improving the mechanical properties of A206 casting alloy using the vacuum assisted, counter gravity casting process.IntroductionThe process of metal casting has been, over the centuries, the chief production technique for components used in everyday life. However, the casting process has certain inherent problems that can adversely effect the properties of a finished product. These problems are directly attributable to the gravity pouring technique used to transfer molten metal to the mold and to fill the mold cavity.A recent study for the American Metalcasting Consortium demonstrated reoxidation products created during the casting process are five times more likely to cause product rejects than entrapped molding aggregates, melt slag, or furnace lining materials1. Formation of nonmetallic and intennetallic compounds are more prevalent in aluminum and titanium alloys because of their reactiveness to furnace lining materials and their high affinity for oxygen. The incorporation of undesirable compounds can be attributed to four areas of the casting operation. The sources are charge materials, melting technique, pouring methodology, and casting cavity filling. Aluminum foundry men have addressed the first three areas by selecting high quality melt stock, non-stirring melting equipment, and the use of porous ceramic filters. Unfortunately, little consideration is given to the last, but yet tl.1e most important part of the casting operation, the actual fill mg of the casting cavity.The generation of inclusion defects during the casting process can be described by two methods. As the liquid metal flows in the gating network and casting cavity, abrupt changes in flow d1rect10n cause the metal to become agitated. This mechanism liquid metal splashing, is generated by instability of the advancing liquid metal interface from turbulence effects as schematically illustrated in figure 1a2 . The surface oxide film bursts under high velocity conditions, folds over, and becomes dispersed and incorporated in the bulk liquid. Additionally, fragmented liquid droplets ejected from the disturbed interface oxidize and become dispersed in the metal stream."

Jan 1, 2000

By N. Pradhan, B. K. Mishra, B. D. Nayak, B. K. Mohapatra, R. K. Mohapatra

"Present study is about use of a group of Iron[Fe(III)] Reducing Bacteria (IRB) to convert the goethite (a-FeOOH) present in the original lateritic Nickel ore to magnetite under an anaerobic condition and subsequently release the bound Co(III) and Ni(II) through leaching. The lateritic Nickel ore contains 0.8% Ni, 0.049% Co, 1.92% Cr, 0.32% Mn and 50.2% Fe. An anaerobic dissimilatory Fe(III) reducing bacterial consortium capable of using acetate as carbon source (electron donor) and lateritic ore as terminal electron acceptor, changes the initial light brown color of the ore to dark brown. The change in color is due to the conversion of goethite to magnetite, which was confirmed by XRD. When the IRB treated sample was subjected to both bioleaching and acid leaching, it shows a greater recovery of Nickel and Cobalt values as compared to untreated original lateritic Ni ore. Further a magnetic separation method was used to separate the magnetic part of the treated lateritic ore and subjected to acid- and bio-leaching for better recovery of Nickel and Cobalt.IntroductionIt has been known that micro-organisms have the potential to reduce metals but more recent observations have shown that a diversity of specialist bacteria and archaea can use such activities to conserve energy for growth under anaerobic conditions [12]. Natural Fe(III) oxides are high in surface area and are reactive [1]. Fe (III) oxides adsorb a wide range of metal cations and anions by complexation to surface hydroxyl groups [17], and function as the primary redox buffering solid phase in many sediments and subsurface materials [5].Recently a number of bacteria have been isolated based on their ability to use metal ions, including Fe(III), as electron acceptor under anaerobic conditions. These are capable of producing energy by coupling the oxidation of organic compounds to reduction of Fe(III). Iron[Fe(III)]-Reducing Bacteria (IRB) have been isolated and identified from a wide variety of environments including freshwater and marine aquatic sediments and submerged soil [8]. The biogeochemical cycle of iron is linked to those of the trace metals, as many trace metals coassociate with Fe(III) oxides or reduced iron phases (e.g., magnetite, siderite, or iron sulfide). IRB can utilize Fe(III) oxides as terminal electron acceptors for respiration [18]; thereby reducing all or a fraction of the solid. The reductive portion of the iron biogeochemical cycle in non-phototropic environments (e.g., sediments and subsurface materials) is driven by the direct enzymatic reduction of Fe(III) oxides to Fe(II) by dissimilatory iron reducing bacteria [13,14]."

Jan 1, 2009

By Miao Tian

Large quantities of copper complex resources are produced globally and urgent to be cleanly processed. This article presents a thermodynamic analysis of mixed smelting process including low-grade polymetallic copper sulfide concentrates, high copper content sulfide concentrates, metallurgical by-products (copper removal slag from lead metallurgy), and copper powder from electronic waste. A top blown smelting reactor to simulate mixed smelting process is developed using a metallurgical process simulator, METSIM. Reactor parameters, heat loss and phase distributions are estimated from actual plant data. The proper proportion between complicated primary and secondary copper resources is determined by analyzing the influence of the feed rates of various resources, oxygen, silica flux and revert on the smelting performance. Autogenous smelting process is built by optimized matching materials of copper complex resources, in terms of the reactor temperature, copper content in matte and slag, and the percentage of magnetite in slag.

By H. Y. Sohn, M. K. McCarter, Bradley C. Paul

"A computer model was constructed for bacterial leaching of the major sulfides found in porphyry deposits, including bornite, chalcocite, chalcopyrite, covellite, cubanite, enargite, native copper, pyrite, and pyrrhotite. The model incorporates equations for the sulfide minerals dispersed in the rock matrix. Leaching occurs by reactions with ferric ion diffusing into the rock fragment: Ferrous ion is resenerated to ferric with oxygen by bacteria at a temperature dependent rate. The model keeps track of the net acid generated, oxygen consumed by the bacterial oxidation of ferrous ion, heat generated, jarosite and hematite precipitated, and copper leached. The model was used to predict the rate of copper recovery, heat generation and oxygen demand for a variety of run-of-mine sized porphyry ores. These results were used in the design of a ventilation system and the economic analysis of a modified in situ extraction method that may be cost competitive with conventional copper production involving open pit mining.IntroductionA study was undertaken at the University of Utah to evaluate the technological and economic feasibility of mining copper by a method referred to as Flood Drain Leach Cell (FDLC) mining. Cells 60 by 75 meters in plan and 70 meters in height are created throughout the ore body by a modified Vertical Retreat Mining technique that includes the removal of 25% swell material. The swell material is leached in finger dumps on the surface while the cells underground are bulkheaded, flooded, drained, and artificially aerated to promote bacterial ferric sulfate leaching. Solutions are cycled through several cells to reach pregnant grade of 1 gram copper per liter of solution. These solutions are then fed to an underground solvent extraction plant and then a surface electrowinning tankhouse."

Jan 1, 1988