Search Documents

By H. Y. Sohn, S. PalDey

"Fine particles of nickel aluminides and Ni4Mo were synthesized by reducing mixtures of, respectively, A1Cl3 + NiC12 and NiC12 + MoC12 vapors with hydrogen. Though thermodynamically favorable, the coreduction of NiC12 and A1Cl3 by H2 to form Ni3Al did not readily happen experimentally. The addition of a small amount of aluminum vapor was needed to initiate the coreduction reaction. The product particles as observed by TEM were very fine but usually agglomerated. The electron diffraction pattern of particles identified NiAl and NiA13 along with Ni3Al and metallic Ni. The content of Ni3Al was maximized at 52 mol% at 1050°C under the partial pressures ofH2, A1Cl3, and NiC12 at 57, 1.4, and 0.5 kPa, respectively. When a mixture of NiC12 + MoC15 was reduced by hydrogen, Ni4Mo particles with some Ni or Mo particles were obtained, the maximum content of Ni4Mo obtained being 93 mol % . The particle size was in the range of 100 to 200 nm. An Ni4Mo coating of 700 nm thickness on an Ni substrate was also prepared.IntroductionThe search for new high-temperature structural materials has stimulated much research on intermetallic compounds. Nickel aluminides have low densities, relatively high melting points, and good high-temperature strength properties. They show an increase, rather than a decrease, in yield strength with increasing temperature (1). Ni4Mo is also of interest as a high-temperature structural material. The major shortcomings of these intermetallics are their inherent brittleness at room temperature when they are in polycrystalline form. For much the same reason, the conventional casting of intermetallics is difficult. Ingot metallurgy and powder metallurgy are two other processing techniques. The first technique is quite energy consuming. In powder metallurgy, the powders of metals and alloys are consolidated in near net shape and then subjected to secondary processing. It would, therefore, be advantageous if intermetallic compounds can be produced in fine powder form from inexpensive raw materials, using less energy."

Jan 1, 1998

By Yimin Ruan

"An inverse design method is developed to obtain the optimal cooling conditions for the continuous quenching of precipitation hardenable sheet alloys to achieve the required yield strength. The yield strength of a precipitation hardenable alloy is obtained by allowing solute to enter into solid solution at a proper temperature and rapidly cooling the alloy to retain the solute in the solid solution. An aging process may be needed for the alloy to develop the final mechanical properties.The objective of the design is to optimize the quenching process so that the required yield strength can be achieved. With the inverse design method, the required yield strength is specified and the sheet thermal profile at the exit of the quenching chamber can also be specified. The conjugate gradient method is used to optimize the cooling boundary condition during quenching. The adjoint system is developed to compute the gradient of the objective functional. An aluminum sheet quenching problem is presented to demonstrate feasibility of the inverse design method.IntroductionQuenching is a critical step in metal production to achieve desired material properties, such as yield strength, hardness, etc., for precipitation hardenable alloys. In most cases, rapid quenching from the solution heat treatment temperature is necessary to obtain the required material properties, but rapid quenching may cause other problems such as excessive distortions of the quenched materials.In a solution heat treatment, the alloy is heated to a suitable temperature, held at that temperature to allow the soluble alloying elements to enter into the solid solution, and cooled rapidly (quenching) to retain the alloy elements in the solid solution. An aging process, which controls precipitation of fine particles at room (natural aging) or elevated temperatures (artificial aging), is generally followed after the quenching process to develop the final mechanical properties of the heat treated alloys."

Jan 1, 1998

By G. J. Abbaschian, A. B. Gokhale, M. M. Kunjapur

"A laboratory scale model furnace was constructed for obtaining radially inward oriented columnar grains in disc shaped castings. The furnace consisted of eleven circular, concentric, equispaced resistance heaters on each half of a split graphite mold. Water or air flowing through a copper pipe along the periphery of the disc constituted the heat sink. After filling the mold, the heaters were turned off consecutively in top and bottom pairs from the rim towards the center, causing the temperature gradients to move inward. Equiaxed structure was obtained at the center by turning off the inner coils together when desired. Sn:15%Pb alloy was used to cast integral blade disc castings using the above technique to obtain dual-property discs with a central equiaxed structure and an outer columnar grain structure projecting inwards from the blades to the rim. A numerical technique was used to predict the temperature profile in the disc during solidification, and good correlation was obtained with the experimentally measured temperature profiles. The corresponding heat transfer coefficient values obtained were h = 544 Wm- 2k-1 (0.013 cal/cm2- ° C-sec) for cooling between metal and chill and h' = 71 Wm- 2k-1 (0.0017 cal/cm2- ° C-sec) for the heat input from the hot mold to the liquid metal. BackgroundHigh temperature alloys used in the current generation of gas turbine engines have evolved through two main stages of development: in 1950's, the increase in the efficiency of gas turbines was paced by improvements in alloy design, which led to the development of Ni and Co-based superalloys (1). By mid-1960's, it was realized that improved alloy chemistry alone was inadequate in meeting the increasingly stringent service requirements. The focus of research then shifted from alloy development to process development, and resulted in the introduction of directional solidification (DS) techniques for the production of turbine blades and vanes (1,2).Under typical operating conditions, the blades and vanes are subjected to aerodynamic loading, while the blades are additionally subjected to high centrifugal loading and vibratory stresses. The primary material requirements for blades may be summarized as follows (1,3):•,High creep resistance•,Good high temperature tensile strength (typically in the range of•,275 to 550 MPa at temperatures in excess of 750°C)•,Resistance to both low cycle and high cycle fatigue (LCF and HCF)•,Resistance to erosion, corrosion, and oxidation•,Resistance to thermal fatigue"

Jan 1, 1986

By Alicia E. Ares

316 L Stainless Steel samples were solidified directionally under conditions which produced the columnar to equiaxed transition. The position of the transition was located in each sample and the distance from the bottom of the ingot was measured. During solidification the distribution of temperatures were measured by means of thermocouples located strategically. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solidus fronts. Comparing the location of the transition and the values of these parameters it was found that the temperature gradient reaches negative values of as low as -13.44 "C/cm, and velocities of the fronts of around 0.1 cm/s. Also, a supercooling of 5.81°C were measured which was associated with the supercooling for the nucleation and growth of the equiaxed grains ahead of the columnar front. In addition the primary and secondary dendritic spacing was measured in both regions. The spacing was compared with the predictions from available models. The results are presented and discussed in the frame of the results obtained for other alloys

Jan 1, 2002

By Dieter Wanner

Off-gas cleaning from metallurgical? plants, requires in many cases very low dust contents which are, difficult to achieve with conventional scrubbers, even with high energy input. Lurgi has developed a scrubber which improves the separation of the fine dust by electrical charge prior to the scrubbing zone,, An Electrostatic Scrubber has been successfully installed for the off-gas cleaning from slag granulation after a waelz kiln achieving less than l mg/m3 in the clean gas.

Jan 1, 1992

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuOQs) increased with increasing slag basicity, defined by Xcao /XSiO, The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuO0.5) increased with increasing slag basicity, defined by XCao/Xsio2 The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003

By Guoqiang Lv, Xi Yang, Wenhui Ma

Cast multicrystalline silicon ingots are widely used in photovoltaic manufacturing. A key issue to achieve high solar cell efficiencies is to attain an optimized temperature field during directional solidification (DS) process. This paper reports numerical investigation of multicrystalline silicon (mc-Si) ingot production using two major types of DS furnace. Specific examination is made on thermal distribution, interface shape and stress field. Evaluation is performed for the applicability of thermal system design to reduce thermal stress, improve crystal quality and enhance energy efficiency. The effects of procedure parameters and geometric configuration on temperature distribution are discussed as well to provide the viable solutions for systems optimization.

Jan 1, 2015

By William Petrul

Image analysis studies were performed on mill products from laboratory flotation tests of the Zn-Pb ore from the Faro deposit in Yukon, Canada, to determine mineral liberations at specific grinds and to predict recoveries at optimum flotation conditions. The minimum and optimum grinds for liberating sphalerite and galena were predicted from size analysis data for the minerals in large ore pieces, and determined by image analysis studies of the mill products. The determined optimum grinds are about 2 Tyler mesh sizes larger than predicted because sane of the fine grained sphalerite and galena occurs in interstices between coarser grained pyrite and is liberated when the pyrite grains are broken apart. Materials balance calculations were performed on the analyzed values for the liberated and unliberated sphalerite and galenaa to determine their distributions in the mill products. The laboratory flotation tests recovered 74% of the sphalerite and 83% of the galena in Zn and Pb concentrates respectively. The mineral evaluation study indicates that the optimum recovery for sphalerite and galena are 85 and 83% respectively. The company is currently recovering 80% 'of the sphalerite and 82% of the galena.

Jan 1, 1989

By C. Flores

A novel process using solid metals for the direct reduction of more noble metal ions from solvent extraction organics has been developed. Base metals recovery has been the principal focus of investigations to date but feasibility tests have now also been made on galvanically stripping selected precious metals. In this study gold (III) was loaded from an aqueous HAuCI4 .3H20 solution into a mixed organic 40 vol.% TBP, 10 vol. % D2EHPA in kerosene. The direct precipitation of metallic gold from the loaded organic phase using zinc powder and iron, aluminum and copper slabs at 70 °C was successfully demonstrated. The gold reduction rates were relatively fast even though the conductivity of the organic solutions is very low. The reaction rates were studied as a function of the variables zinc particulate size, oxygen and nitrogen atmosphere, water content in the organic phase, organic ratios and temperature. The gold morphology was usually powdery or dendritic in nature but continuous films were obtained in some instances. Activation energies were calculated and possible reaction mechanisms are discussed. In general, the results obtained were very promising and showed that gold can be successfully cemented from selected organic solvents by galvanic stripping using less noble solid metal reductants.

Jan 1, 1995

By Shizhe Liu, Bing Li, Heng Wang, Zuxin Zhao

In this paper, cyclic voltammetry and chronoamperometry have been applied to investigate the effects of Nd2O3 concentration on the anode effects, critical potential for the anode effects and Nd2O3 reduction in LiF-NdF3-Nd2O3 melts at 950℃. The results show that the oxidation peaks in the potential of about 2.7V are attributed to the oxygen ions oxidation and the peak current density increases with Nd2O3 concentration increase from 0 to 0.5wt%. The critical potential caused the anode effects shifts to 0.3V more positive value as Nd2O3 content in the melts decreases from 0.01wt% to 0.5wt%. The cyclic votammograms on W electrodes in the LiF-NdF3-Nd2O3 melts present two pairs of reduction and oxidation peaks, indicating that the reduction of Nd ions in the LiF-NdF3-Nd2O3 melts in two steps rather than one step.

Jan 1, 2014

By C. J. Newman

The new Kennecott Utah Copper smelter, started in 1995, was designed to be the cleanest smelter environmentally in the world. The plant is operating at production rates above the original design capacity. Copper concentrate is smelted in an Outokumpu flash smelting furnace. Matte is granulated and processed using Kennecott-Outokumpu flash converting. Copper anodes are processed in a modernized copper refinery using the Kidd Process while anode slimes are processed for precious metals recovery using a unique hydro-metallurgical process. To allow the production of high quality cathode, using modem smelting and converting technology to minimize emissions, impurity control had to be carefully addressed. All process bleed streams from the smelter and refinery are treated in a hydro-metallurgical plant to fix impurities in a stable form, allow for the rejection of impurities as required and recover valuable metals. Special technology was developed for the copper refinery to ensure production of high quality cathode from anodes containing high levels of impurities. The smelter routinely achieves a sulfur capture in excess of 99.9% which is equal to less than 2 kg of SO2 per tonne of copper produced. This paper describes the design of the smelter and refinery and includes recent production and emission data and modifications carried out to allow operation at above the original design rates. It emphasizes the unique features required to achieve environmental and quality goals and compares environmental performance data to that published on other smelting operations. The processing of intermediate streams, the management of recycled materials and the impurity control strategy will be covered in detail.

Jan 1, 1999

By Ray Y. Lin, Randall A. Blue

"Joining of silicon carbide with infrared using a mixture of Si-30wt.%C as the brazing material has been investigated. Joining was performed at a temperature of 1500 °C in a flowing argon atmosphere for processing times ranging from 5 to 60 seconds. The joining filler materials include thin film silicon obtained by thinning down silicon wafers to about 70 /!m and graphite powder of a 15 /!m average particle size. Joint strengths were determined with a specially designed shear-in-compression jig for testing shear strengths of brittle materials. Cross section examinations of the joined specimens with optical microscopy, scanning electron microscopy and transmission electron microscopy have shown that all joints are essentially void free with excellent wetting between the base SiC and the brazing material. Silicon carbide in the B form has been identified as the reaction product in the joining zone with a transmission electron microscope (TEM) and selected area diffiaction (SAD) analysis. At 1500 °C with a joining time of 60 seconds, the joint has consisted of primarily SiC. With such a high SiC content in the joint, the joint strength is comparable to those by other joining techniques, such as diffusion bonding, as reported in the literature. A kinetic model for the formation of SiC from liquid silicon and carbon is proposed to explain the observed joint microstructural evolution.IntroductionSilicon carbide is of great interest for high temperature structural applications because of its excellent high temperature strength, wear resistance and anticorrosive characteristics [1]. Even though the interest in SiC is high, the use of the material has been limited by the high cost and difficulties involved in forming components of complicated shapes [2]. It is these limitations that necessitate the development of effective joining techniques that are cost effective and able to provide strong joints."

Jan 1, 1996

By Sevinc Yildirim, Cigdem Oruclus

"Metal-Porous Silicon (PS) based structures dipped in water show the direct hydrogen fuel cell behavior. The effect of the thickness of the cupper (Cu) film on the electrical properties of direct hydrogen fuel cell is studied by fabricating Cu/Porous Silicon/n-Silicon/Indium structures. PS samples were produced electrochemical etching of n-type single crystalline silicon with a resistivity of 1,25 Ocm and (111) orientation. The thin films of Cu with different thickness between 200 and 600 nm were deposited on PS surface by electron-beam technique. Investigation of the effect of Cu layer on the performance of the structure indicates that the performance parameters such as open circuit voltage (Voc) and short circuit current (Isc) strongly depend on the Cu layer thickness. It was observed that the divice with an 350 nm Cu layer exhibits the highest open circuit voltage (0,5 V), short circuit current (0,01 mA) and power density (10 W.m-2).IntroductionHydrogen is the most attractive and ultimate candidate for a future fuel and an energy carrier. Hydrogen is recognized as the environmentally desirable clean fuel of the future since it can be used directly in different types of hydrogen fuel cells [1]. In the past years, the rise in portable electronics requires the development of miniature fuel cells compatible with standard silicon micro fabrication technology. Most silicon micro-fuel cells have used the polyperfluo-rosulfonic acid membranes (Nafion R) as a proton exchange membranes (PEM) that is not really integrated with standard micro fabrication techniques [2-5]. The composite materials such as inorganicorganic hybrid materials (Nafion-silica, Nafion-borosiloxane etc) are next generation of proton conducting membrane [4-8]. But, fuel cells run on pure hydrogen gas, which can be produced with other energy resources. Hydrogen smallest atom and thus the H2 gas can leak easiliy. The application of hydrogen for power sources has been greatly restrained due to the lack of safe and convenient generation and storage methods.A kind of hydrogen fuel cells Metal-PS-Si structures used as an energy water directly. There is no need pure hydrogen. Cu-PS-Si Schottky-type fuel cells with as proton-conducting membrane and the thin-film cupper catalist and water as fuel, which are interesting for fabrication of lowcost miniature fuel cells. Generation of the open-circuit voltage and short-circuit current has been observed by Cu-PS-Si structure dipping in different hydrogen-containing solution."

Jan 1, 2014

By Oleg Ostrovski

Industrial pyrometallurgical processes in ferrous metallurgy are based on carbothermal reduction of metal oxides. Carbothermal reduction of stable oxides requires high temperatures. Lowtemperature reduction can be implemented by using methane-containing gas with high carbon activity, or by carbothermal reduction under reduced CO partial pressure. Under standard conditions, methane is thermodynamically unstable above 550 °C and decomposes to solid carbon and hydrogen. At appropriate CH4/H2 ratio and temperature, carbon activity in the methane-containing gas phase can be well above unity relative to graphite, which provides favorable thermodynamic conditions for reduction. To maintain these conditions, the rate of reduction/carburisation should be higher than the rate of solid carbon deposition. The paper discusses reduction of pure manganese and chromium oxides at relatively low temperatures, and constraints in reduction of manganese and chromium ores. Reduction of metal oxides by carbon in hydrogen as an alternative use of natural gas is also discussed.

Jan 1, 2014

By Patricia Negrini Siqueira

Abstract. Polymers are susceptible to changes in their chemical structures that affect their mechanical properties under weather condition. Exposure of plastics to UV radiation causes a loss in their mechanical properties and/or change in appearance, including reduced ductility, color changes, yellowing and cracking. Today, there are several additive systems (light stabilizers) developed to work according to resin, final application, type of cultivation, and other characteristics. This study evaluates the different additive systems (Hindered Amine Light Stabilizer - HALS, nano calcium carbonate - NPCC, nZnO and nTiO2), applied 0.75% (in weight) in linear low density polyethylene (LLDPE). The samples were mixed by high rotation homogenizer and extrusion. Later, the samples were molded by injection and aged in QUV-B simulating 6 months of exposure to weather. Tests of FT-IR and tensile strength comparing to the non-aged samples were carried out in order to evaluate the performance of several additive systems.

Jan 1, 2015

By V. V. Satya Prasad, A. Sambasiva Rao

Electroslag melting technologies have recently been developed for recycling light scrap of valuable metals and alloys such as superalloys and oxygen free high conductivity (OFHC) copper at Defence Metallurgical Research Laboratory (DMRL), Hyderabad. Conventionally, electroslag melting processes use consumable electrodes. Because of the difficulty in compaction of scrap into a consumable electrode of satisfactory quality, non-consumable electrodes such as graphite and water-cooled copper have been designed. Electroslag remelting using a water-cooled non-consumable electrode was developed to melt scrap of a nickel base superalloy. Sound ingots with smooth surface finish and properties comparable to vacuum melted superalloys could. be obtained from scrap using this process. A modified electroslag crucible melting process using graphite crucible and graphite electrode was developed for recycling OFHC copper scrap. Copper ingots with less than 10 ppm oxygen and electrical conductivity"" 100% IACS could be produced. The same process was also utilized to produce copper-based alloys such as copper-chromium and copper-titanium starting from copper scrap.

Jan 1, 2000

By Liu Chunpeng

Under an inert atmosphere, the temperature enhancement of nickel bearing pyrrhotite irradiated by microwave was measured with a special metal-sheathed thermocouple and the non-isothermal rate equations were obtained. Under the controlled oxygen potential of the reacting gas in the microwave field, over 90% sulfur contained in the pyrrhotite is converted into elemental sulfur directly, the iron and the nickel are transformed into FeO,, NiO, NiFe,O, and FeSiO,. According to the experimental data the rate of the elemental sulfur produced is in diffusional control and the non-isothermal equation derived is

Jan 1, 1993

By Cleusa Cristina Bueno Martha de Souza

Nowadays in Brazil the final disposal for spent batteries include sanitary and industrial landfill for hazardous waste from domestic waste and industrial waste respectively. The problems of environmental impact caused by spent batteries had been discussed of several years, considering the fact of metals contents, like Cd, Hg, Pb and Zn. Some techniques are been proposed for recycling this type of waste in order to protect the environment while bringing also economic advantages of recovering metals. The reclamation of metals from secondary raw materials had been employed and further applications of this flexible technology are planned to the future. The processing of metals solutions involving hydrometallurgical techniques is an efficient method for recovering metals, since it provides completely recovery of metals with low energy requirements. This paper discusses the spent alkalline batteries characterization and leaching stage experiments results with sulphuric acid as leachant. After batteries dismantling by mineral processing techniques, the black powder sample produced was submitted to diffraction X-ray characterization and atomic absorption spectrophotometry in order to verify all the substances presented. Some experiments were carried on to develop a hydrometallurgical process for initial metal recovery aiming to get Zn into a soluble form on aqueous solution in order to propose the next stages of purification and recovering Zn, as electroplated deposition. The sulphuric acid was chosen not only for being cheaper than other leachants but also for improving the extraction of soluble Zn as ZnS04 form at diluted acid concentration. Batch laboratory experiments leaching procedure were conducted to determine appropriate leaching conditions from the viewpoint of maximize zinc extraction. In these tests an amount of dry powder batteries was added to different acid concentrations and solid/liquid ratio and after leaching and filtration the aqueous solutions were submitted to atomic absorption spectrophotometry analysis to verify the Zn content.

Jan 1, 2000

By David J. Kinneberg, Barbara E. Mangion, Arnold M. Savolainen

Analytical laboratories require a qualitative or semi-qualitative method of determining major and minor constituents in "unknown" samples to select optimal analytical techniques. This is exceedingly important in precious metal assay laboratories where the precision and accuracy requirements are exacting (routinely within 0.02%, absolute basis). This paper describes the use of an x-ray fluorescence spectrometer with a specially designed software package to select optimal analytical procedures and specify relevant analytical parameters. A wavelength dispersive XRF spectrometer is capable of quick and accurate analyses of properly prepared samples without extensive standardization. When coupled with a specially designed software package, this preliminary assay system is applicable to a wide variety of sample types including gold and silver bullion, karat gold and karat PGM alloys, high silver and high copper metallic samples as well as particulate samples of ores and sweeps. The system relieves the assayer of tedious calculations for silver inquartation and proofing, minimizes human error and standardizes selections over time. Most importantly, the system allows for independent verification of final assay results.

Jan 1, 1999