Search Documents

By A. W. Fletcher

A nickel-copper sulphide concentrate was treated in a pilot plant at Warren Spring Laboratory during 1961, by a hydrometallurgical roast-leach- solvent extraction process devised to cleanly separate the metal values, and produce acid sulphate liquors containing the metals. It is shown that 86 percent of the nickel and 95 percent of the copper could be leached from the calcine, after a sulphatizing roast on finely ground flotation concentrate. Iron was removed from the leach liquor by limestone neutralization with a small loss of values. Copper and nickel were separated by solvent extraction with naphthenic acid in kerosene after partial neutralization of the iron-free liquors with ammonium hydroxide. Hydrogen sulphide and chlorine were used to remove zinc (and residual copper) and cobalt impurities respectively. The recovery of pure copper and pure nickel, by electrowinning, from the acidic solvent extract strip liquors finally produced, appears technically feasible.

Jan 1, 1964

By Richard L. Bullock

OPEN STOPING An open stope is an underground cavity from which the initial ore has been mined. Caving of the opening is prevented (at least temporarily) by support from the unmined ore or waste left in the stope, in the form of pillars, and the stope walls (also called ribs or abutments). In addition to this primary support system of open stoping, some secondary support may also be required using rockbolts, reinforcing rods, split pipes, or shotcrete to stabilize the rock surface immediately adjacent to the opening. The secondary reinforcement procedure does not preclude the method classified as open stoping. There are many forms of open-stope mining used to extract the initial material from a mine. Having once established that the mineral and waste rock are competent enough to use an open-stoping method, and assuming that the reserve is not classified as gassy, the Form which the method will take is primarily determined by the dip and thickness of the reserve. How these two factors affect the selection of the open-stope mining is discussed in a later chapter. At this point it will suffice to say that the classification of the open-stopes mining system which follows is based on whether dry' broken materials flows by gravity or whether it must be moved by nongravity methods where energy must be supplied to move the material. Room-and Pillar-Mining Room-and-pillar mining is an open-stoping method where mining progresses in a nearly horizontal or low angle direction by opening multiple stopes or rooms, leaving solid material to act as pillars to support the vertical load. Since the direction of excavation (angle of dip) is below that which would cause the dry material to flow by gravity to a drawpoint or gathering point, the material must be loaded in the room where it was extracted and transported to a point where it will flow, either by gravity or mechanical means, to a central gathering point to be taken out of the mine. This is an important aspect of room-and-pillar mining which differentiates the system from other open-stope mining methods which rely heavily upon gravity to transport ore from where it was broken to a lower elevation, usually through a drawpoint. There are many variations of the method which go by a number of names in local districts: breast stoping, breast-and-bench stoping, board-and-pillar, stall-and-pillar, and panel-and-pillar are all basically open-stope room-and-pillar mining. In some instances detailed stope planning is almost nonexistent; i.e., the operator simply follows the visual pay values, leaves pillars only where necessary, and tries to locate them in the zones of lower value. This method of mining is as old as the beginning of underground mining itself, dating back thousands of years. Early in the history of mining in this country, the term "gophering" was used to describe this method (Peek 1941). The term is appropriate, for it brings to mind the exact results of this type of system-a random and irregular room-and-pillar mine. In other instances where the mineral values are consistent both in physical dimensions and quality, the mine layout can be planned to the last detail, resulting in a uniform room-and-pillar mine. Coal, trona, gilsonite, potash, oil shale, salt, limestone, and sandstone mines can usually follow such a system. Today, most metal mines using a room-and-pillar operation try to mine as regular a pattern as possible but deviation in height, width, thickness, dip, and grade of the ore results in comparable deviation in the mine plan. Variations of the Room-and-pillar System It is necessary to briefly describe some of the many variations of the room-and-pillar system of mining, enabling the reader to fully explore the concepts and become familiar with the terminology used before going on to the details of mine design. Full-Face Slicing: If in the process of opening the rooms the total vertical extent of the mineral values of the particular seam or strata are extracted from the advance of one vertical face, the term used to describe this is full-face slicing. This face is also known as the "breast." There is no mineral of economic value intentionally left either in the floor or the roof (back) to be mined later. To be able to extract the full-face height in one pass, the mining equipment must obviously be designed to reach as high as the back. In an Appalachian coal mine, this may be all of 660.4 mm (26 in.); for a future oil shale property it might be 15.24 m (50 ft). Normally, however, in a majority of mines where the mining face gets over 6.09 to 6.7 m (20 to 22 ft), the tendency is to divide the face into more than one pass. Over this height, it becomes difficult to properly see and remove loose rock from the back with a hand "mining bar." Where the process of taking down loose rock has become mechanized, higher full-face mining can be safely practiced. Most eastern and midwestern coal seams and western uranium, trona, and potash seams in the United States are easily reached in a single face; many limestone, lead, and zinc mines must resort, at least in part, to "multiple-slicing" to remove all the minerals of value. Multiple Slicing (also known as multiple-pass mining): In many cases it is not practical to carry the full vertical height of the mining horizon as a full face. The face is divided into parts known as the breast, bench, and/or brow. Ideally, if the operator knows the vertical extent of the mineralized zone, he will drill and blast the first pass at the top of the zone, thereby

Jan 1, 1982

By S. Tuylu, D. Adiguzel, U. G. Akkaya, A. Bascetin

"One of the main problems for storing of the tailings is acidity occurrence due to several factors such as existence of sulfuric minerals and also the pollution in seepage waters by mobilization of metal ions, which holds great risks in terms of environmental regulations. Because of these specified reasons, tailing materials to be used in a SPD formula should have comply with some specifications. Among these properties; oxygen content, temperature, matrix suction and pH are the most important parameters. In the study, the relationships between the parameters mentioned are investigated to reveal optimum paste design layout. The lowest amount of seepage water obtained from the paste layers in the pilot cabinet was found as 2150 ml from 3rd layer. As for the maximum seepage water and the average of the all 11 layers were found as 4909 ml from 6th layer and 3273 ml respectively. The reactions occurring according to the oxidation, as seen at seepage water of second and third layers, decreased the pH of system to the under of 7 value. Additionally, when the seepage water of first layer’s EC value is 2.93 mS/cm, the EC value of second layer is increased at 3.54 mS/cm. The other parameters are evaluated with the obtained results of the tests to determine the optimum storing conditions for SPD.INTRODUCTION Conventional waste disposal methods, although widely used, pose great environmental risks. One of the most important issues is acid mine drainage (AMD). Tailings of metallic mines contain heavy metals, aggressive chemicals and hazardous materials. In the presence of oxygen and water, an oxidation reaction can occur, causing a decrease in pH of the environment, and heavy metals that are present in the environment can dissolve easily. Subsequently, heavy metals can pollute underground water basins, creating a great amount of danger for the ecology and potable water resources. Another important risk associated with conventional waste disposal methods is accidents related to the waste dam. Higher volumes of water and tailings (usually 15% solids and 85% water by weight) are sent to waste dams, making it very difficult to control the stability of the dam under conditions such as static and dynamic loads (seismic activities, vibrations caused by blasting, etc.), flooding, and seepage. In case of an accident or failure, the spread of great amounts of mud containing hazardous chemicals and heavy metals can harm the environment of the dam site significantly (Bascetin et al., 2014). In the paste technology, depending on the type of ore, tailings used in the paste mixture can contain sulphide minerals (such as pyrite and pyrrhotite). These minerals are known to be reactive with water and oxygen to produce acidity (sulphuric acid)."

Jan 1, 2015

By E. R. DeMen

In late 1965 General Mills announced the availability of a new liquid ion exchange reagent, LIX®-64, for the recovery of copper from various solutions, such as dump leach liquors. Acceptance of this material by the copper industry has been gratifying. A number of pilot plants have been operated, and at this writing there are four commercial plants either in operation or under construction. The properties and operating characteristics of this reagent have been described in previous papers.1,2 LIX-64 is quite effective and selective for copper extractions although partially limited in pH ranges, losing extraction efficiency as the acidity of the feed solution increases to below pH 1.0. Also, the LIX-64 content in the kerosine carrier was limited to about 10 volume percent (except for special cases) because of rapidly decreasing phase disengagement rates above this content. This in turn led to large plant capital costs, as the organic flow rates had to be in- creased (rather than LIX-64 content) to extract the copper from high content liquors. This was true in all circuits where the feed copper content ran above 2.0 g/l copper. A reagent was needed which would extract copper from more acidic liquors (or higher copper content liquors) and which exhibited improved phase disengagement characteristics with reagent contents up to 30 volume percent. General Mills is pleased to announce the availability in commercial quantities of a new and improved reagent, L+-64~. This reagent broadens the pH range in which copper can be extracted, and exhibits superior phase disengagement characteristics. The improvement in the reagent has been noted in laboratory circuits, as well as pilot plant runs and commercial operations.

Jan 1, 1970

By W. G. Pariseau

"BACKGROUND The Crandall Canyon Mine (CCM) is located in the Wasatch coal field in central Utah. Extensive longwall mining at CCM preceded a decision to recover coal left in barrier pillars on each side of a set of main entries extending far into the mine. During mining in March, 2007, a major bump occurred that led to cessation of mining in the barrier pillar on the north side of the mains and to begin mining in the south barrier pillar. Subsequent loss of ground control in August, 2007, through coal pillar bursts had tragic consequences with loss of six miners and shortly afterwards three rescue team members. An MSHA report describes the events in detail (MSHA, 2008). An important lesson to be learned from CCM is the need to select a computer program suitable for pillar design. Computer programs are engineering tools; selecting the right tool for the job is essential. In this regard, a minimum program requirement is capability for computing stress distribution within a pillar and adjacent roof and floor strata. The reason is simple: strength of rock is stress dependent; both vary from point to point in pillars and adjacent strata. Preferably, one should follow the evolution of stress as the mining plan is executed from start to finish to assure safety or to warn of a potentially hazardous situation developing as mining progresses. The approach to the problem posed by barrier pillar mining at CCM is conventional in the sense of applying well known finite element modeling techniques to analysis of a proposed mining plan. The engineering purpose is to evaluate the mining plan with respect to ground control questions including roof, floor and pillar safety. Results of previous two dimensional finite element analysis indicated pillar safety was by no means assured (1, 2, 3). Geometry of barrier pillar mining is limited in two-dimensions, for example, crosscuts are not seen in vertical cross sections. While three dimensional analyses are preferred, even moderately sized regions often lead to very large problem sizes that exceed computer capabilities. However, a recent development in finite element modeling of tabular deposits allows for whole mine analysis in three-dimensions. This technique involves a dual node – dual mesh concept. Both have been used separately in much earlier work, but are only now are used in combination. Estimation of subsidence at a kilometer scale and details of stress, strain and displacement about barrier pillars, main entries and pillars, and so on at a meter scale are possible (4). No compromise involving empirical formulas or similar guess work is required. Indeed, all calculations are based on first principles: physical laws, kinematics, and material laws. Effects of joints and in situ variability or uncertainty in strata properties, elastic moduli and strengths, may be included for greater realism. An important objective of the present study is to assess the role of three-dimensional pillar geometry in arriving at conclusions regarding barrier pillar mining versus two-dimensional results."

Jan 1, 2015

By John M. Marek

INTRODUCTION This paper is for the mining manager, generally meaning mine superintendent, chief engineer, and others who have control over the mine operation responsible for feeding the insatiable beast called the mill or processing plant. The author is not from mine management but from the field of technical mine engineering consulting. This fact illustrates the authors gross inadequacy to comment on this subject. On the other hand, the consulting profession allows visits to many mine operations, worldwide, supplying many different commodities. The common complaints and misunderstandings that have been heard worldwide will be shared within the following few paragraphs. In order to discuss optimization, one must first define it. There certainly will be many papers in the following sessions that claim to optimize something, or other, based on a technical definition of cost, efficiency, throughput or some other quantifiable basis. DEFINE OPTIMIZATION Actual optimization of an operation is not as easily achieved as most of us in the technical world would like. Borrowing terminology from the technical world, the boundary conditions and the optimization function are usually not well defined. The problems in many cases do not lend themselves to quantification. Typical management procedures are to establish goals or strategies that set the approach or general boundary conditions to the overall plant. Three simple cases are listed below as possible corporate strategies to optimization of a mine-process plant complex. 1) Maximized discounted cash flow 2) Minimized long term cost of product 3) Maximized resource utilization This list seems simple when presented in the above context, uncluttered by constraints such as market position, capital availability, or environmental limitations. Sometimes the best approach is a prioritized combination of the above items. Typically, the Board or CEO has established these strategic priorities. They may

Jan 1, 1991

By Vijenac Quarry, A. Iljazagic, t. Knezicek, T. Omeragic

Limestone quarry Vijenac, is one of the key limestone producers in B&H. Conventional massive drilling and blasting is the technique applied for limestone exploitation. Utilized blasting scheme causes appearance of large oversize stone pieces, uncontrolled flying stone and undesirable seismic effects. In order to reduce or eliminate exposed disadvantages and to improve environment in the area of Vijenac quarry, an innovative blasting scheme was tested. Conventional blasting scheme was changed from single row, deep inclined blast holes combined with two lines short horizontal holes to multi row, inclined blast holes combined with a single line short horizontal blastholes. Applied innovative blasting scheme reduces negative blasting impact on the environment through safer working conditions, reduced amount of dust after blasting, reduced explosive and energy consumption, reduced appearance of explosive gasses and reduced earth and air vibrations as the result of seismic effects.

Jan 1, 2005

By H. C. Juvkam-Wold

The design of an aquifer depressurization system is discussed. The system uses a number of wells surrounding a mine shaft to reduce the aquifer pressure in the vicinity of the shaft. The effect of various parameters such as number of wells, wellbore diameter, time and well location is discussed. It is concluded that, with a properly designed depressurization system, the aquifer pressure and the water inflow rate to the shaft may be reduced to less than 15X of their potential values in the absence of wells

Jan 1, 1980

By A. F. Grandt

What is prime farmland? Can such land, once it has been strip-mined for coal, be restored so that it will produce corn, soybeans, wheat, and alfalfa? What methods or practices are necessary to bring about restoration within a reasonable time so that crop yields will be equivalent to or higher than those of unmined prime farmland under high levels of management? These questions concerned land use researchers in Illinois as early as 1948 when the Illinois Agricultural Experiment Station experimented with growing cultivated crops on strip-mined land in St. Clair County (1). This research was done almost 30 years before requirements of Public Law 95-87 were passed by the United States Congress and signed August 3, 1977.

Jan 1, 1980

By James A. Decker

Hanna has developed three production planning systems to help the mine engineers determine the sequence of mining from available ore supples. The Production Scheduling System was developed to give the staff a tool for long range planning by sequencing the removal of blocks from an open pit property. It was needed to determine the year of removal for each block so that the optimum present-valued pit limits could be established by our pit design program. Since in this type of planning short term grade control is less of a factor than it is in daily or monthly planning, the system gives the program greater control and more latitude in block selection. It permits only full blocks to be taken.

Jan 1, 1984

By J. D. Miller

Physical separation of bitumen from low-grade Utah tar sand deposits containing a relatively high viscosity bitumen phase (Sunnyside and Tar Sand Triangle deposits) has been accomplished by traditional size reduction and froth flotation techniques. At appropriate experimental conditions more than 90 percent of the bitumen can be recovered in a concentrate, containing more than 20 weight percent bitumen, which should be a suitable feed material for subsequent hot water or thermal processing. The efficiency of bitumen recovery depends on the extent of size reduction, promoter and dispersant addition. Rejection of greater than 60 percent of the sand at ambient temperature and ease of water removal from the concentrate make such a process strategy both energy and cost effective. The energy required to achieve effective separation by the ambient temperature process is significantly less than the energy required for the recently developed hot water process. The flotation behavior of the tar sand has been analysed with respect to flotation pH, contact angle measurements and the apparent iso- electric point of the bitumen. The best flotation response at pH 7.8 to 9.0 can be correlated with the maximum in contact angle developed between the air bubble and bitumen surface and with the apparent iso-electric point of the bitumen (-pH 8.0).

Jan 1, 1981

By J. T. Crawford

A comprehensive strategic planning model has been developed for the phosphate strip mining and chemical operations at White Springs, Florida. The computerized model covers ore body modeling, production simulation and financial analysis. Several innovative features in the model include using NPV techniques in ore body block economics, adapting the floating cone method to a floating template for generating dragline mining units automatically, using interactive graphics for designing mining units, and a dragline move economics algorithm for automatic scheduling of mining unit assignments and moves. Simulation of chemical plant production uses linear programming and concentrate inventory levels control mine operating schedules.

Jan 1, 1997

By Kumara S. Rachamalla

Mineral activity in Ontario represents an annual production in excess of $4 billion. The Ontario government encourages the mining industry to undertake mineral development through grant programs and incentives offered by mineral resource taxation. Computers are playing an increasingly important role in improving productivity in the administration of incentive programs and the Mining Tax Act in Ontario. This has meant speedier processing of grant applications and tax returns which is resulting in a streamlined approach to incentives and taxation in Ontario. The use of computers has resulted in significant contributions to key areas of concern such as assessment of mining tax returns, analysis of the changes, if any, to the Mining Tax Act and modeling of the Ontario Mineral Exploration Program (OMEP). Implementation of state-of-the-art technology such as Local Area Networks (LAN's), fourth generation languages and integrated micro-mainframe information processing has resulted in improved productivity as well as lower costs. As a result, the respective services provided to the mineral industry by these two programs are now delivered in an efficient and cost-effective manner utilizing the latest available computer technology.

Jan 1, 1986

By M. L. Klohn

The Felder ore deposit is a 5,000,000-pound uranium deposit in the South Texas Coastal Plain. It occurs in the basal sand of an Oakville Formation (Miocene) alluvial system. The host sand is a carbonate-rich arkose which contains virtually no carbonaceous debris and has been reduced by the local introduction of hydrogen sulfide. The ore lies well within the reduced zone and occurs as coffinite and uraninite that fill interstices and coat and replace grains. The overall geometric configuration of the ore is that of a winged, crescentic ore roll. Weak mineralization extends the wings of the ore roll and gives greater expression to the roll character. Departures from the shape are controlled by discontinuities in bed- ding and by proximity of the ore to the surface. Associated with the uranium is a broad halo of anomalous molybdenum. Subsidiary mineralized trends suggest a pre-existing up-dip position for the main roll. Oxidation from the surface largely destroyed this previous roll by solubilization of uranium. Uranium subsequently migrated into favorably reduced sand and reprecipitated at the present roll position.

Jan 1, 1970

By Yoginder P. Chugh

Effects of moisture absorption on the behavior of the Dykersburg shale overlying Harrisburg coal seam in Southern Illinois are presented in this paper. Cylindrical samples of the shale 2.5 cm in diameter and 5.0 cm long were studied for weight gain and swelling strains at 90, 95, and 100 percent relative humidity and under immersed water conditions. After attaining equilibrium conditions, the samples were studied for changes in the strength and deformation behavior. The depth of moisture penetration was measured using the Vickers microhardness measurements. Using the basic mass transfer concepts, effective diffusion coefficients were computed for the shale.

Jan 1, 1980

By P. T. Luckie

Analysis of classifier performance independently of a closed grinding circuit configuration may result in a poor match-up between the grinding device and the classifying device. This paper examines the relationship between classifier and grinding device in dry grinding circuits by employing a semi-empirical methodology.

Jan 1, 1980

By Pascal Deschamps

"INTRODUCTION During the last decades, many underground facilities for the storage of hydrocarbons have been excavated worldwide and the technology is fully mature. Similarly to other underground structures, the initial basic design has to be adapted along with the work progress, in order to cope with the actual site conditions and in particular the geology, hydrogeology and associated rockmass quality. In addition, Client’s or underground Contractor’s constraints (such as resources availability, schedule or cost impact) may vary from design to construction and require last minute adjustments. Engineers are required to introduce flexibility and anticipation of unexpected situations (similar to the above-mentioned) while conceiving large underground facilities. Although most of the cases require only minor adaptations, crucial parts of the facility have sometimes to be considerably modified and reviewed. This article will present four cases evidencing how the design of one of these essential structures - the concrete plug – has been adjusted during site implementation without impairing the initial performances. Hydrodynamic containment The product containment of the unlined caverns discussed here is ensured by the principle of hydrodynamic containment. A permanent water flow is naturally or artificially maintained with an orientation toward the storage cavern and then, neither product-tight membrane nor lining are required. The hydraulic gradient (and the associated water flow lines), being directed from the surrounding mass toward the cavern, prevent from outward migration of the product. If the hydraulic gradient is not sufficient or if the water table is evidencing instability, water can be artificially injected into the rockmass through purpose-built boreholes, drilled from dedicated galleries. This water injection system, called the water curtain, is generally located several tens of meters above the level of the cavern. This principle is illustrated here after."

Jan 1, 2016

By Richard J. Fantel

This paper addresses the impact of declining world rutile resources upon the production of titanium products and their asso¬ciated costs. Titanium is used primarily for the production of pigments; in its metal form it is considered a strategic and critical material to the U.S. defense and aerospace industries. There are two major mineral sources for titanium: ilmenite and rutile. Both these mineral types can be used to produce titanium pigments. Only high grade titanium concentrates, such as rutile, high-grade ilmenite, and synthetic rutile (which is produced through further processing of ilmenite), can be used in the production of titanium metal. This paper draws upon the data and analyses of a recent Bureau of Mines Minerals Availability Program appraisal that evaluated the international availability of titanium from market economy countries. The paper will show that production from economic rutile mines will decline sometime after the turn of the century and that rutile shortages could be alleviated by production from other high-grade titanium resources such as higher cost rutile deposits and anatase deposits, or through an increase in world synthetic rutile capacity.

Jan 1, 1984

By C. A. Rawlins, P. Rostami

"Ventilation systems are not only an integral part of any underground mine design but are a significant contributor to the mine’s capital and operating costs. The ventilation and cooling design systems presented in this paper were part of the prefeasibility evaluation of an underground platinum mine in South Africa. The mine would ultimately operate at the depth of 1,200 m below surface with a proposed 4 Mtpa production rate. The proposed mining operation is a highly mechanized operation using diesel equipment. Significant daily production rate, large amount of equipment and expansive nature of the operation, contributed to a challenging while flexible ventilation design requirements. This paper presents how to safely and efficiently optimize capital expenditure and operating costs associated with the mine air cooling and refrigeration system through practical ventilation design practices. Successful capital and operational savings by modulating installation and commissioning of refrigeration facilities can influence the economic realization of such systems. The adapted planning and design approach provided a cost-effective advantage while complying with design safety and regulations. INTRODUCTION This paper outlines a prefeasibility evaluation of the heat loads and related cooling system to be employed at the proposed platinum mine. The paper also provides appropriate details for a comprehensive understanding of the applied methodology. The proposed mine will be a trackless underground operation using a combination of mining methods. Initially, ore zones with vertical thicknesses greater than or equal to 18 m will be mined using the long-hole stoping (LHS) method, while thinner ore zones will be mined using mechanized drift-and-fill or drift-and-bench methods; hence, a highly mechanized operation with LHDs, trucks, drill rigs, personnel carriers, etc. is envisioned. Broken rock (ore and waste) will be transported by the means of trucks to the main passes (ore and waste) and collection points. Mining zones identified in the project occur at depths ranging between approximately 700 m to 1,600 m below surface. Primary access to the mine will be via a 1,100 m deep, 10 m diameter production shaft (named Shaft No. 2), three additional shafts will be sunk to provide future ventilation and production support. Three main access levels are established as primary haulage levels and include a series of interconnecting ramps. Additional mining sublevels will be developed as necessary. Figure 1 shows the proposed shaft locations and main access levels in a 3-D elevated view. Mining is performed using highly productive mechanized methods. For this reason, an annual ventilation estimate is based on requirements for mobile equipment (i.e., 0.06 m3/s/kW). The air requirements imposed on the underground operation is further influenced by equipment heat loads, auto compression, and virgin rock temperature, as the main sources of in-mine heat."

Jan 1, 2015

By D. G. Chedgy

Environmental improvement efforts are focusing with increasing intensity on pollutants resulting from combustion. The high cost of removing these pollutants at the power station is well documented. Physical coal cleaning has always been and should remain the most economic method of reducing sulfur oxide emission from coal combustion. It is critical in the selection of preparation plant circuitry to consider capital and operating costs, as well as the level of sulfur reduction. This paper describes the technical criteria which must be used for efficient process selection and summarizes the cleaning systems available or in development.

Jan 1, 1990