Search Documents

By Hingant Pierre

The Hurtières Tunnel was built in 1995 with drill and blast method, in metamorphic schist. It is located between Lyon and Torino on the A 43 motorway in the French Alps. During the construction, a geological hazard was encountered, which caused a massive ground collapse. The tunnel was filled up with 3,000 m3of glacial materials. Geological investigations realized after the accident showed that a narrow glacial valley was present at this location the water table was 40 m above the tunnel level. The paper will describe the collapse and the remedial methods which were implemented to proceed through the failure area. These included drainage works,2,000 m3 grouting and 6,200 ml jet grouting columns.

Jan 1, 1999

By V. A. Evans

The preparation of a paper reporting fluorspar economics in the United States at one point in time could have been somewhat complicated be- cause of the number of producers, both large and small, that derived production from different locations throughout the Western U. S. and the Southern Illinois and Western Kentucky fluorspar districts . Companies such as Allied Chemical and William- son Mining operated in the Jamestown district of Colorado. In Walden and Salida, Colorado, the Colorado Fluorspar Company operated mines and mills.

Jan 1, 1986

By P. D. Rao

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherent and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' recent research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Jan 1, 1997

By Joseph Clare

It’s not the 1960s anymore. Upgrading wastewater pipelines in the current era demands the latest trenchless technology to minimize impacts. King County Wastewater Treatment Division in Seattle, Washington is designing a nearly mile long Direct Pipe® influent sewer combined with microtunneling to replace a 1960s era trunk sewer constructed along and within Coal Creek and its natural area. Trenchless installation using Direct Pipe® and microtunneling was chosen due to reduce impacts to residential neighborhoods, natural creek environments, and the constraints of topography

Jun 13, 2021

By F. D. Ayhan

The aim of this study was to investigate desulfurization and de-ashing of a mixture of subbituminous coal and gangue minerals by the agglomeration method. For this purpose, experimental studies were conducted on a mixture containing subbituminous coal, pyrite, quartz and calcite. The effects of some parameters that markedly influence the effectiveness of selective oil agglomeration, such as solid concentration, pH, bridging liquid type and concentration, and depressant type and amount, were investigated. Agglomeration results showed that the usage of various depressants (Na2SiO3, FeCI3, corn starch, wheat starch) in the agglomeration medium has a positive effect on the reduction of ash and total sulfur content of agglomerates. It was found that an agglomerate product containing 3.03% total sulfur and 25.01% ash with a total sulfur reduction of 56.71% was obtained from a feed that contained 7% total sulfur and 43.58% ash when FeCI3 was used in the agglomeration medium. Key words: Desulfurization, De-ashing, Agglomeration, Coal, Gangue minerals

Jan 1, 2009

By Paul R. Wieber

This paper describes the U. S. Energy Research and Development Administration's (ERDA) program to develop in situ coal conversion processes, especially gasification, he potential of this technology, the technical directions being explored, and the program strategy to carry the process concepts toward commercialization are emphasized. The geographic location of the U. S. coal resources and a market analysis are described. Commercially successful in situ coal processes could add over a trillion tons of coal to the U. S. coal reserves. The economics of these processes is compared with surface gasification independent studies show this process to be 25Z cheaper than surface gasification for Western coals. The major projects are briefly described. The Linked Vertical Well process is in the lost advanced stage and shows great promise. The last test produced a low-Btu gas averaging 171 Btu per standard cubic foot for average pro¬duction rates of 5.5 million standard cubic feet per day. The other projects are Packed Bed, Longwall Generator, and Steeply Dipping Beds.

Jan 1, 1977

By B. Berg, J. Stephenson, J. Mansanti, C. Nyikos

"Intrepid Potash, Inc.’s Carlsbad East facility has refined sylvite and produced muriate of potash (MOP) since 1965. In addition to MOP, Intrepid Potash began recovering the mineral langbeinite from a mixed ore reserve in 2005. In 2011 a new langbeinite recovery process for the coarse (+850 micron) size fraction was constructed to enhance the overall langbeinite recovery. Based on the limited mixed ore reserve and an abundance of langbeinite ore reserves the transition of the East plant to a langbeinite only facility was targeted for 2021. Due to a decreasing grade of the mixed ore reserve, declining sales pricing, and high sylvite operating costs a strategic decision was made to accelerate this transition into 2016. To enable a successful transition, a fines recovery system needed to be developed, constructed and implemented. This paper describes the advancement of langbeinite processing at Intrepid Potash and the planning, development and successful execution of the transition to a langbeinite only operation. BACKGROUND Langbeinite (K2SO4·2MgSO4) is a double salt containing potassium sulfate (K2SO4) and magnesium sulfate (MgSO4). It is used as fertilizer and in the industry is described as Sulfate of Potash Magnesia. It is attractive as a specialty fertilizer and in addition to containing a ready source of a primary nutrient potassium, it also provides two secondary essential nutrients, magnesium and sulfur. It is especially attractive for chloride sensitive crops. Langbeinite has a specific gravity of 2.8, a Mohs hardness of 4.2, and is brittle thus very friable. It is the hardest of the saline minerals, and despite its relative softness on the Mohs scale can be very abrasive in process environments and in field applications, probably due to its conchoidal cleavage. Its solubility at 240 g/l is less than the solubility of sylvite (KCl) or halite (NaCl) and due to even slower relative dissolution kinetics washing with cold water has been a common practice for upgrading langbeinite ores. The solubilization/crystallization relationship for langbeinite is different from the majority of other evaporite minerals in that once langbeinite is solubilized it does not form langbeinite again. Instead it gives up one mole of magnesium sulfate, takes on various waters of hydration and precipitates out as either schoenite (K2SO4·MgSO4·6H2O) or leonite (K2SO4·MgSO4·4H2O) depending on temperature. Due to its partial solubility and phase transitions at its surface when exposed to moisture, there is strong cohesion between wetted particles; the resulting stickiness of the upgraded products can create significant materials handling issues unless processed in slurry form or at relatively low moisture levels. Langbeinite has been produced commercially from two locations, the Kalush and Stebnik regions in the Cartpathian Mountains of former Poland and now the Ukraine and from the Permian Basin in New Mexico (Garrett, 1996; Smith 1949). Current production is from two operators in the U.S., Mosaic and Intrepid Potash."

Jan 1, 2017

By R. L. Wiegel

A well-defined geometric model for a mineral system and its liberation by size reduction is used to show the relationship between true volumetric particle composition and the composition estimates obtained by the measurement of linear intercepts or areas of simulated polished sections of particles. Based on this information, a transformation is developed between the areal measurements and the volumetric composition for this idealized mineral system. Key words: Gaudin random liberation model, Mineral liberation, Particle composition measurement

Jan 1, 2010

By E. H. Kurt

INTRODUCTION The simplest way to drill a hole into rock is to strike a steel chisel or drill bit with a hammer. Early miners used this elementary hand technique so successfully in "single jacking" and "double jacking" that the first mechanical rock-drill designers sought to duplicate it. However, in the early developments, the designers were forced to retreat to a construction known as the "piston drill," wherein the entire drilling element is tied to the piston and reciprocates with it. It took nearly 50 years to devise a method of divorcing the two elements and to achieve the original hammer principle used in hand drilling. The Mont Cenis tunnel, drilled through the French Alps in 1861, usually is considered the birthplace of the mechanical rock drill. The Hoosac tunnel in Massa¬chusetts was drilled at about the same time, and the success of these two ventures paved the way for innova¬tions that produced the Burleigh, Ingersoll, Sergeant, and Waugh piston drills between 1870 and the turn of the century. In 1897, George Leyner of Colorado introduced what has been considered the most significant development in rock-drill history. He devised the hollow drill steel for water flushing; when combined with his free-piston hammer drill, this became the first lightweight and dust¬free underground machine. In addition, Leyner's drills introduced improvements such as automatic rifle-bar rotation of the drill steel and chuck, automatic lubrica¬tion, and an enclosed throttle control. During the 1920s and 1930s, automatic feeds, centralizers, sliding cones, and the automatic water back head were developed, laying the groundwork for all pneumatic underground drills currently in use. Since these pioneering efforts, rock-drill development has been concerned primarily with refining the designs and improving the metallurgy to make faster, lighter, and more dependable machines. Fig. 1 illustrates the progress in drilling speed during the first 125 years of rock-drill development; that progress is a credit to the persistence and inventiveness of the designers in the rock-drilling industry. ROCK-DRILL CLASSIFICATIONS To meet the variety of conditions encountered in rock drilling, several distinct types of drills have been de¬veloped. In general, rock drills may be classified as either hand-held or mounted, with the hand-held ma¬chines including the jackhammer or sinker, the jackdrill or jackleg, and the stoper. The mounted drills are com¬monly known as "drifters." Table 1 shows that each type of drill is available in several sizes from different manufacturers. Fig. 2 illustrates a typical rock drill, showing the principal components. The jackhammer or sinker, shown in Fig. 3, is used primarily for general mine utility work such as drilling anchor holes (short vertical holes to bolt or anchor machinery), pin holes (short, usually horizontal holes to fasten sheaves, etc. to side walls), popholes (for blasting large boulders), and similar applications. They also are used for shaft sinking. Jackhammers are classified ac¬cording to weight, and they range from 7 to 30 kg (15 to 65 lb). The rock drill originally known as a jackleg was made by clamping a pneumatic cylinder or leg to a jack¬hammer, both to support the weight of the machine and to feed the tool forward in horizontal or uphole work. The more modern jackdrill refined this concept to make the hinged pivot for the leg integral with the drill cylinder and to group all drill and leg controls in the drill back head for convenience. Fig. 4 illustrates a typical jackdrill. Jackdrills are classified according to cylinder bore size, ranging from 60 to 83 mm (2.375 to 3.25 in.). Because of their light weight and versatility, jack drills are very effective in small drifts, small tunnel head¬ings, and stoping. The larger machines are applied to hardrock formations and in applications where drilling speed is a primary consideration. In soft formations or

Jan 1, 1982

By W. G. Pariseau

Reliable stress measurement using hollow inclusion gauges and monitoring stress change using borehole stress meters and borehole deformation gauges in anisotropic rock remains a challenge for the rock mechanics community. In this regard, the complex variable method advanced in 1983 for deducing stress in anisotropic rock is flawed and software is privileged. Fortunately, advances in computer hardware and software now enable fast, reliable reduction of hollow inclusion stress measurement data for determining stress in anisotropic rock. Monitoring stress change in anisotropic rock poses a different challenge but is also subject to numerical analysis. Stress measurement using a hollow inclusion (HI) gauge such as the triaxial Australian HI is done in four steps: 1) drilling a measurement hole, 2) installation of an HI, 3) stress relief of the HI by overcoring, and 4) data reduction. The last step, data reduction, is the focus of this work. The process is well-known in linearly elastic, isotropic rock (Worotniki and Walton 1976, Duncan Fama and Pender 1980). However, in case of linearly elastic, anisotropic rock the requisite technology is not readily available. This situation is somewhat surprising because anisotropy is more often the rule rather than the exception, especially in the neighborhood of ore bodies. Rahn (1984) has pointed out the potential for significant errors with neglect of anisotropy and the adverse consequences for engineering design. Amadei (1984) has also pointed out the potential for errors with neglect of anisotropic rock properties in stress measurement. Worotniki (1993) cites other studies that indicate potential for serious errors when doing measurements in anisotropic rock. In both theoretical cases (isotropy and anisotropy), data reduction is essentially a composite of solutions to boundary value problems in linear elasticity. In the finite element approach, the analysis is a simulation of gauge hole drilling, installation and overcoring. Two important advantages with the finite element approach are a more faithful representation of the conditions of HI stress measurement than approximated in theory and the capability for handling rock whether isotropic, transversely isotropic or fully anisotropic

Mar 2, 2022

By Ronald J. Roman

A mathematical model was developed for the grinding and flotation section of Union Carbide's Bishop mill and this model was used to indicate how variations in grind, retention time, and calcite and fluorite content effects the mill capacity, tungsten units produced, and the grade and recovery of the scheelite concentrate. A model such as this is a starting point in determining the economic optimum running condition for a mining and milling operation and an example of this is given.

Jan 1, 1969

By Joseph Sopko, Xavier Lacourse-Dontigny

For the REM (Réseau Express Métropolitain) project, a 2500 m tunnel was built using a tunnel boring machine (TBM) under the Montreal Pierre Elliott Trudeau Airport (ADM). Although the geology under the Montreal Airport (ADM) would have been suitable for an excavation with a hard rock machine, the rst section reuired an earth pressure balance (EPB) TBM due to the soft soil located under wetlands. After excavating 280 m, the TBM was blocked in a transition zone of unconsolidated, water-bearing soils directly above the underlying bedrock. A free air intervention was not possible due to these geological conditions. After several failed attempts to create a slurry cake for hyperbaric interventions, a ground freezing system was designed and implemented, incorporating angled pipes drilled from outside the wetlands to directly in front of the cutterhead. This paper discusses the engineering reuired to form a frozen, water-tight zone in front of the cutterhead using liuid nitrogen. It also describes the complex method of replacing the disc cutters while holding the ground freezing system active in a manner protecting the health and safety of the workers.

Jun 23, 2024

By M. E. Grimes

Rio Algom Mines Ltd. owns eight uranium mines and mills in the Elliot Lake district of Ontario, seven of which were producing before 1960. At present only one mine is operating meeting current contract requirements. Under present economic conditions, it is not feasible to mine ore of less than 2.0 lbs./ton U308, although there are very large reserves below this grade. We are interested in preconcentration for three possible applications: to extend ore reserves by permitting use of lower grade ore, to reduce costs on processing of present grade ore, and to reduce capital investment in expanding production to meet future production goals.

Jan 1, 1973

By Kiran B. Chaudhuri

The Kivcet process is technologically the most advanced of the new lead smelting processes which have been developed over the past decade construction of the first commercial scale Kivcet lead smelter which has been designed by KHD Humboldt Wedag for Sociedad Complejo Metalurgico de Karachipampa is at present nearing completion in Bolivia. Some of the measures taken to minimise emission of harmful elements as well as methods employed to minimise energy consumption in the design of the smelter, are presented. Results of recent testwork which have added to the flexibility of the process are summarised.

Jan 1, 1982

By John Murray, Daniel Ebin, Robert Gould, Yiming Sun, Lizan Gilbert

The Atlanta Plane Train Tunnel West Extension is being constructed at Hartsfield-Jackson Atlanta International Airport using the Sequential Excavation Method (SEM). The tunnel has shallow ground cover and mixed-face conditions and passes underneath the SkyTrain and MARTA stations and airport terminal buildings. It includes a twin tube Bifurcation with a span of over 45 feet and ground cover of 12 feet. A flat roof is being constructed at the Bifurcation to maximize rock cover and minimize surface settlements. This paper focuses on design and construction challenges for the Bifurcation and tunneling beneath the world’s busiest airport, while minimizing impacts to operations.

Dec 1, 2022

By L. J. Vincze

The program of study of pellet binder materials was begun by the ORF in 1963 to examine various Canadian materials as substitutes for bentonite which is imported in large tonnages (199,270 tons in 1969) from the U.S.A. for Canadian pellet plant operations. Most of the raw bentonite used in Canada originates in Wyoming, North Dakota and more recently Greece, resulting in relatively high transportation costs to pellet producers. Some Canadian bentonites available in Western Canada (Alberta) can be beneficiated for uses as pellet binders but could not compete in cost with U.S. sources due to the cost of beneficiation and the higher rail transport charges to Eastern Canada. It is difficult to find a substitute for bentonite, and many materials have been investigated by research groups but, so far, no economic substitute is in use. However, some success is apparent in studies of low cost materials such as clays, sea weed, peat moss and low grade coal, The work done by the ORF over several years has covered systematic test¬ing of Ontario clays, lignite, some types of tree bark, waste sulphite liquors of various kinds, and peat moss as binders for iron ore pellets. The major effort has been concentrated on peat moss and has included a study of the influence of different additives. Since analysis of peat moss for humic acid is difficult and time consuming, a certain amount of time was devoted to development of improved methods, the most useful of which was a spectrophotometric method based on extraction of peat by sodium pyrophosphate for determination of humic substances. In the present paper, only the most recent work concerning the use of peat moss with suitable additives is discussed in detail, since it is the most conclusive and best documented portion of the program.

Jan 1, 1971

By Yongsik Jeong, Kwangmin Kim

Conventional tailings slurry contains a significant amount of water, and water management is key to ensuring the stability of a tailings storage facility (TSF). Simply reducing the water content in the slurry before discharging it from the mill could be an effective way to improve TSF water management. This study investigated the potential for using an environmentally friendly polymer as a new drag reduction agent (DRA) to reduce frictional pressure loss and also conserve water. It entailed conducting pipe loop tests to assess the polymer’s effect on pressure loss in tailings flow and then applying the test results to validate a numerical model using computational fluid dynamics (CFD). The model was also used to determine the polymer’s optimal concentrations at given solid concentrations and flow rates, its effect on energy efficiency for tailings transportation, and its potential for saving water. A case study for a mid-sized, hard-rock mine with a throughput of 50,000 t/day found that the solid concentration could be increased from 30 to 45% with no pressure loss by applying 1996 m3 of the polymer per day. Adding the polymer also resulted in water savings of 57,552 m3/day. The results of this study demonstrated the potential for using the new DRA not only to improve TSF stability but also to save water.

Jun 29, 2020

By Robert W. Bruhn

State and federal regulations require that surface mine overburden be investigated in advance of mining for naturally occurring earth materials that are detrimental to animal and plant life or to uses of water. Proper identification of these toxic materials is necessary to permit development of environmentally sound reclamation programs. Intensified use of present laboratory methods to meet anticipated testing demands would be both costly and time consuming. This paper discusses the desirability of and general requirements for a geophysical system capable of locating toxic zones in the overburden of surface mineable lands of the Northern Great Plains Coal Province. The paper (1) identifies the types and character of naturally occurring overburden substances that must be investigated in advance of mining, (2) discusses the economic justification for development of a geophysical system to replace or to complement conventional laboratory test methods, and (3) discusses the potential applicability of downhole geophysical methods to overburden analysis.

Jan 1, 1981

By A. G. Ulsoy

In recent years there has been an Increasing Interest In the application of automatic control theory to mineral processing systems, and numerous applications of mineral process control have appeared in the literature. A general approach to the synthesis of mineral process control systems is presented. The first phase of the control system design consists of specifying the control objectives, process variables and their interactions; these topics will be discussed with specific reference to mineral processing. The second phase Is con¬cerned with selection of control strategies algorithms, instrumenta¬tion, and other components of the control system and is discussed at length. These concepts are then illustrated by a flotation control case study.

Jan 1, 1981

By D. H. Y. Tang

3-dimensional finite element modeling was performed to analyze the safety factors of stump pillars, 18 ft. x 18 ft., under a cover of 208 ft. using the Modified Drucker-Prager Theory. The results showed that they are safe. This was substantiated by underground observations. But the safety factors predicted by three commonly used pillar design formulae showed otherwise. This paper discusses the modeling details and anlyze the difference between 3-D FEM method and traditional pillar design formulae.

Jan 1, 1987