Search Documents

By M. A. Rodrigues da Silva Enríquez

One of the rare consensual points among different resource-based economic analytical approaches refers to the strategic role of rent from mineral extraction, as a decisive tool to ensure that the temporary wealth generated in the present can turn into permanent income in the future. For this reason, evaluation, distribution and use of mining rent plays a central role in the sustainable development of mining cities. Brazilian legislation provides for this at the municipal level by means of participation in the financial results of mineral extraction accomplished in these municipalities, with the Financial Compensation for Mineral Exploration (CFEM). CFEM is a type of ad valorem royalty, which charges taxes of up to 3% of the net revenue of mineral production. However, legislation does not establish how these resources should be used. Therefore, there is wide variation in the use of CFEM income among Brazilian mining cities. A study from a sample of the 15 largest mining cities in eight Brazilian states made possible identification of two main patterns with regards to the use of CFEM which were labeled "sustained use" and " the pitfall of the single treasury." In that regard, this article discusses the pressuring factors that contribute to these patterns, as well as the institutional arrangements which may be more favorable to inducing more sustained use of CFEM.

Jan 1, 2011

By Carl G. Bock

INTRODUCTION Rapid transit systems involving near surface tunneling in hard rock are becoming more numerous, especially along the northeast corridor of the East Coast. Tunneled systems are under construction in Washington, D.C. and are being planned for Atlanta, Buffalo and Baltimore. Near surface tunneling is defined for this paper as being that in which the crown is 100 feet or less below ground surface. For Rosslyn Station, the total cover ranged from 52 to 70 feet. The rock cover, however, ranged from 40 to 50 feet which is slightly less than the station height and about two-thirds of its width. Rosslyn Station (Fig. 1) is the only station excavated completely in hard rock in the Virginia portion of the 98.5 mile Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system. The station site, oriented in a north-south direction beneath a main thoroughfare and flanked by multistory office buildings, was fixed by the need to serve a dense population center at a specific location and geologic conditions were a secondary consideration in siting. There was no previous underground rock excavation in the Washington Metropolitan Area of the size and scope of Rosslyn Station that offered a practical case history guide to the geologic conditions and excavation problems to be encountered. GEOLOGY The regional geology of the Washington Metropolitan Area is divided into two physiographic provinces by the northeast trending Fall Line (Fig. 2). Northwest of this boundary is the Piedmont Province

Jan 1, 1974

By Sarah Vest, Richard Sherman, Leo Martin

In 1988 a major exploration program was undertaken to determine the characteristics of the rock and soil for a 7.6 m diameter sea outfall tunnel beneath Boston Harbor out into Massachusetts Bay. The diffuser discharge location had been mandated by the EPA to a 10 sq. km area of seafloor connected to the proposed Deer Island Treatment Facility by a 14.5 km tunnel corridor. Geophysical surveys, deep rock borings, and laboratory testing, provided the information for the conceptual design. The program identified the range in material types and parameters to prove feasibility of a TBM driven tunnel and to locate the optimum alignment and depth.

Jan 1, 1991

By Thomas H. Koenning

The number of spontaneous combustion incidents in the U.S. is expected to increase as the consumption of lower rank coals and the use of longwall mining becomes more prevalent. A spontaneous combustion incident holds the potential for substantial loss of life from a mine fire or explosion if not prevented or controlled at an early stage. Laboratory tests have been developed which are useful in ranking the susceptibility of various coals to spontaneous combustion. Ventilation circuits and mining methods can be designed to minimize the risk of spontaneous combustion. Early detection of spontaneous combustion is possible with the combined use of continuous monitoring, periodic gas sampling, and inspection.

Jan 1, 1989

By Mark W. Springett

The examination of relatively well behaved distributions subject to truncation by a cutoff grade in the mine clearly demonstrates that a bias is inevitably introduced when the selection is based on the results of samples which are subject to even the most idealised error distribution. The idealised error used in this paper is assumed to be normally distributed with a mean of zero and is thus unbiased. The bias introduced can be minimised but it cannot be eradicated. A better understanding of the bias can lead to improved procedures for mine sampling, sample preparation, assaying and estimation of selection units which will not only reduce the discrepancy but more significantly will increase the efficiency of mining selection and hence profitability.

Jan 1, 1989

By Jeffrey A. Holcomb

INTRODUCTION The passage of Comprehensive Environmental Response Compensation and Liability Act (CERCLA/Superfund) as well as the Resource Conservation and Recovery Act (RCRA) and state laws, have placed added regulatory pressures on the mining industry. These laws which focus on the regulation of hazardous substances and wastes for the protection of the public health and welfare and the environment, present the potential for tremendous financial impacts and liabilities on existing mine operators and owners and/or potential mine operators/owners. This paper takes a brief look at these laws and presents an environmental audit procedure to identify environmental liabilities prior to mine land transactions. The environmental audit approach presented is an overview of the procedures that could be used to document, evaluate and inventory existing and/or potential environmental concerns. This audit procedure can be applied to developed or undeveloped properties and at active or inactive mining sites. REGULATORY OVERVIEW Mining environmental liabilities have been addressed in RCRA, Superfund, the Clean Air Act (CAA) and the Clean Water Act (CWA). Even though the U.S. Environmental Protection Agency (EPA) has determined that mining wastes will be treated as solid wastes under RCRA and not as hazardous wastes, these wastes could still bring about a great deal of financial liability under Superfund. The catch is if the mine wastes generated contain hazardous substances such as the heavy metals arsenic, beryllium, cadmium, chromium, copper, lead, mercury, nickel, selenium, silver, thallium, zinc and others as well as cyanide. Thus, it is not only important for a mine operator/owner or a potential mine operator/owner to know if the mine wastes generated are hazardous, but it is important to know if the wastes contain hazardous substances. Following is a brief overview of RCRA and Superfund and their potential implications. RCRA RCRA, which provides the basis for the regulation of solid and hazardous wastes, is applicable to active mining and milling sites. Within RCRA the definition of a hazardous waste is provided. This definition applies to owners and operators of mining and milling sites if the operator has stored, disposed or treated hazardous wastes on-site. If this is the case and if strict process control and waste management activities are not adhered to, environmental liabilities may be associated with the site. Superfund The 1980 Superfund law can be applicable to inactive mining sites or to inactive sections of an active facility. The provisions of Superfund call for the regulation of hazardous wastes and hazardous sub- stances disposal and release not only by the existing owner, but also for any previous owner. This concept of joint and several liability means that one party, as among many, can be held totally responsible for the costs of hazardous waste cleanup (Haller, 1987). Furthermore, liabilities under Superfund have also been applied back to past acts; thus, several mining properties, active or inactive prior to the 1980 Superfund law, are at risk of being placed on the EPA's National Priority List (NPL) for cleanup. Last years amendments to Superfund, known as the Superfund Reauthorization Act of 1986 (SARA), provided some significant developments for the mining industry. The major requirement of the amendments as it pertains to owners or operators of mining sites is that the EPA must revise its present Hazard Ranking System (HRS). This is important be- cause in most cases the primary reason for several mining sites having been included on the NPL was due to the large volume of wastes generated. As is typical at most mining sites, large volumes of low toxicity wastes are generated and the current HRS model prejudices against this. It should be noted that this provision only applies to sites that are not already on the NPL or have not been proposed for inclusion on the list.

Jan 1, 1987

By P. R. Hervey, J. W. Foise

Quartz is the second most widely used electronic material, with approximately 3,000 t (3,300 st) of single crystals used each year. Most of the quartz used in electronics is synthetic and is manufactured using a technique called hydrothermal growth. This paper reviews the basics of hydrothermal growth, the feedstocks used for these crystals and the challenges to improving the growth process. This paper also reviews the processing of these crystals, the markets and applications where they are used, and the global outlook for these markets.

Jan 1, 2002

By Dermot M. Ross-Brown

The objectives of this generic study were to use numerical modeling techniques to determine under what conditions seismic waves generated by an earthquake might cause instability to an underground opening, or cause fracturing and joint movement that would lead to an increase in the permeability of the rock mass. In general, the study showed that moderate earthquakes (up to 0.41 g) did not cause instability of the tunnel or major fracturing of the rock mass. An artificial rock-burst tremor with high accelerations, however, was found to be amplified around the tunnel, and fracturing occurred as a result of the seismic loading in salt and granite. In shale, even moderate seismic loading resulted in tunnel collapse.

Jan 1, 1981

By Erie F. Wolstenholme

The purpose of this paper is to describe work undertaken, within the System Dynamics Research Group at Bradford Management Centre, into the development and application of a System Dynamics model of an international mineral industry; aimed at providing a basis for analysis of the interrelationship of supply, consumption and price over time, under different production and stocking policies. A review is presented of some of the major characteristics and problems associated with such industries. This is followed by an outline description of the model and the way it has been applied to examine various supply responses, in the light of changing consumption patterns. Demonstration results deal with model validation and with analysis of international buffer stocks and conflicting supply policies on the historic situation in the copper industry.

Jan 1, 1979

By S. K. Sharma, D. A. Stanley

The US Bureau of Mines is investigating the fundamentals of the flocculation process. The objective of this study was to determine the effects of various physico-chemical parameters, namely, shear rate, polymer dosage, and polymer concentration, on floc growth and to determine the applicability of a model for predicting polymer flocculation behavior. A rapid in-line particle size analyzer was used to follow the progress of both the floc growth and the breakage as a function of time. A genetic algorithm (GA) was used to determine the unknown parameters in the model and to fit a curve to the experimental data. The results showed that the model reproduces the experimental data with only reasonable accuracy and that it was relatively insensitive to the parameters. Results of the flocculation study showed that increases in the polymer dosage had a greater effect on the time required to reach the maximum floc size than on the floc size itself: It was also determined that, given all the above parameters, the degree of slurry mixing during the flocculation process had the greatest bearing on floc growth.

Jan 1, 1995

By Byron C. Hardinge, E. R. Palowitch, Albert W. Deurbrouck, David J. Akers, Edward R. Torak

During 1983, 42.2% of the 686.0 (624.3 Mt) million tons of coal reported, 289.6 (263.5 Mt) million tons were mechanically cleaned, of which 107 (97.4 Mt) million tons were cleaned by dense media (magnetite and sand) processes.' The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 38% between 1938 and 1983. The Electric Power Research Institute estimates that 150 million tons (137 Mt) of coal were cleaned by heavy-media processes in 1986, and that this number may increase to 265 million tons (241 Mt) by 1990.2 Dense medium separations include those coal preparation processes that clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes generally offer the following advantages over other coal cleaning processes: • Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of raw coal whose specific gravity is near the specific gravity of separation. • Ability to maintain a separating gravity that can be controlled within + 0.005 sp gr units. • Ability to handle a wide range of coal sizes. • Ability to change specific gravity of separation to meet varying market requirements. • Ability to handle fluctuations in feed, in terms of both quantity and quality. Unfortunately, dense medium processes can have the following disadvantages: • Relatively high capital costs caused primarily by the need for equipment to collect and recycle the medium. Relatively high operating costs caused primarily by operation of medium recycle equipment and loss of medium.

Jan 1, 1991

By Robert L. (Original by) Llewellyn

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment.

Jan 1, 1981

By Randy J. Mikula

Cleaning of low-rank coals can have several meanings, depending upon the definitions of the terms "low rank" and "cleaning." In general, low-rank coals would be lignite or subbituminous according to the ASTM classification. For the purposes of this summary, cleaning is defined to be any process which materially reduces the proportion of inert material in the coal. For low-rank coals, this often means a reduction in moisture content since moisture is the major inert component in these coals. A brief discussion of conventional cleaning processes is included, as is an extensive reference list.

Jan 1, 1991

By K. A. Foo

Minproc Resources Inc. is developing a tailings retreatment project in Bolivia at the Colquiri zinc-tin-silver mine, in the Bolivian Andes. Mining at Colquiri has been continuous since 1940 and COMIBOL, the Bolivian state mining company, has owned and operated the underground mine since 1964. There are 10 million tonnes of tailings at Colquiri containing 0.51% Sn, 4.21% Zn and 50 g/t Ag. Minproc plans to mine and concentrate the tailings at 1.15 million tonnes per year to produce feed for pyrometallurgical upgrading. The tailings are moderately complex, with cassiterite grain size ranging from 200 to 5 pm. The marmatite (ZnFeS) in the tailings is relatively easily recovered, with zinc recovery of 80% to a 40%-45% Zn concentrate. The major problem with the zinc metallurgy is that the marmatite is complexed with iron, which results in iron contents of 14%-17% Fe in concentrate. This makes the product very difficult to sell because of the low Zn:Fe ratio. Most zinc smelters require a Zn:Fe ratio of 6:1 or 7:1, whereas this concentrate has a 3:1 ratio. Concentrate sale terms are therefore unfavorable, and the high cost of transportation from Bolivia to the smelters is an additional burden.

Jan 1, 1992

By Steven Atkin, Rens Verburg, Bryony Hansen, David McWharter

The use of paste tailings as underground backfill and for surface disposal is rapidly expanding, and with it comes the requirement to understand and predict its long-term environmental stability. This paper presents the results from a kinetic testing study performed on cemented tailings paste mixtures under both subaqueous and subaerial conditions. In addition, the effects of grainsize reduction are investigated. It will be demonstrated that the long-term weathering behavior of tailings paste is controlled by its physical and chemical characteristics, as well as its placement conditions. The testing indicates that subaqueous disposal of paste inhibits acid generation, whereas the exposed samples produced acidic leachate despite the presence of cement added to meet geotechnical requirements.

Jan 1, 2000

By E. D. Attanasi

Exploration for non-fuel minerals has declined since 1988 as recessionary pressures have slowed growth in the industrialized economies. By most accounts, however, 1990 expenditures were still significantly greater than the low levels experienced in the mid-1980s. The Persian Gulf crisis introduced instability in energy prices and greater uncertainty into an already cloudy economic picture. As 1990 unfolded, the US savings and loan problems spread to the commercial banking system, leading to the failure of several major US commercial banks. The Japanese stock market also suffered significant losses as Japan's Central Bank raised interest rates. The Soviet Union experienced shortages of food and other basic items. Its government faces resistance to changes leading to a market economy. Individual Soviet republics also are seeking more control of their own destiny. The cost of German reunification, in terms of the capital required to bring the east's infrastructure and industrial base to western standards, also appears to have been underestimated.

Jan 1, 1991

By C. B. Rash, W. W. Fowler, Gill Montgomery

INTRODUCTION Fluorspar is the common term used for the mineral fluorite, which is naturally occurring calcium fluoride (CaF2). It is the principal source of fluorine, the most reactive of the chemical elements, from which a great variety of unique and strategically important chemicals are produced. Commercial deposits of fluorspar are widespread throughout the world, and its availability is essential to the industrial progress of all nations. GEOLOGY AND MINERALOGY In its pure form fluorspar, CaF2, contains 51.1% calcium and 48.9% fluorine, and has a sp gr of 3.18 and a hardness of 4. It is commonly a glassy mineral. colorless, white, or grayish. but may also be various shades of purple, pink, blue, green, yellow, or tan. It belongs to the cubic system mineralogically, and commonly crystallizes into cubic shapes in vugs and cavities, although most of it is massive, with interlocking crystals. Minable fluorspar deposits, in descending order of importance, occur as bedded limestone replacement deposits along fault zones; fissure-filling vein deposits; breccia filling in limestones, dolomites,

Jan 1, 1985

By X. Wen, D. Tao, B. Li

A high effective method using a hammer mill, a column pneumatic separator and an electrostatic separator was studied for recycling copper from waste printed circuit board. The factors influencing the copper liberation degree and following separations were discussed. Two different physical separating methods were compared and discussed. Experiment results show that a well-controlled impact action can produce a satisfactory degree of copper liberation at a relatively coarse particle size. Around 90% copper recovery from printed circuit board for coarse particle size can be achieved by using a combination of electrostatic separation and pneumatic separation.

Jan 1, 2003

By Jacques Mongrain, Serge Barbeau, Gary Brierley

The Communaute Urbaine de Montreal is currently involved in construction of the South Interceptor which consists of 53 kilometers (33 miles) of 1,800 mm (6.0 ft) to 5,400 mm (18.0 ft) diameter tunnels for the purpose of collecting, storing, and delivering sanitary and combined sewage to the treatment plant. Work is divided into ten separate contracts; nine of which have already been bid. The purpose of this paper is to describe construction activities that have been performed through the end of 1986 with emphasis on a general layout of facilities, a summary of subsurface conditions, and brief descriptions of actual construction activities for the six contracts where tunneling has been performed. All projects are being excavated with tunnel boring machines.

Jan 1, 1987

American Barrick Resources Corp. has come farther, faster in the last 11 years than any mining company in recent memory. Acquisition of Lac Minerals Ltd. in August 1994 now makes Barrick the largest gold producer in the world outside South Africa. In terms of market capitalization, the company is the world's most valued gold producer. American Barrick's 28.3-km2 (7000acre) Goldstrike property on Nevada's Carlin Trend, the primary engine for past growth, was purchased in 1987 for $62 million. Regarded as an attractive exploration target, Goldstrike instead propelled American Barrick to the front rank of world gold producers. In 1993, the company produced 50.75 t (1,631,988 oz), 44.78 t (1,439,929 oz) from Goldstrike. Reserves on the property totaled 905 t (29.1 million oz) at the end of 1993, the largest in North America.

Jan 1, 1994