Search Documents

By H. J. Bickel

This paper is concerned with general concepts and statistical devices used in projecting overall energy requirements. Particular emphasis is given to the use of individual end- use markets as an approach to developing future overall energy requirements, and translating these requirements into fuel consumption.

Jan 1, 1962

By Franklin B. Woodbury

As part of its goal of helping maintain an adequate supply of minerals to meet national economic and strategic needs, the U.S. Department of the Interior's Bureau of Mines is evaluating alternative technologies to treat oxidized taconites. Since process control is an essential element in the application of these process technologies, research was performed with a prototype monitoring system. A Californium-252 neutron source and a thermal neutron capture- gamma ray spectra analysis method was utilized to measure the amount of iron and the percent solids in the process slurries. The concentrate and tailing streams in a 410-kilogram-per-hour (900- pound-per-hour) pilot plant employing a selective flocculation and cationic flotation process were monitored. The results obtained showed that the thermal neutron capture-gamma ray reaction can be used to provide process control parameters.

Jan 1, 1979

By D. J. Boron, R. Kollrack

Introduction The US has the largest total (364 Gt, or 401 billion st) and recoverable (182 Gt, or 201 billion st) coal reserves in the world (Steam/Its Generation and Use, 1978). However, progressive coal use in this country has been hampered by environmental constraints, such as restrictions on sulfur dioxide, nitrogen oxides, and particulate emissions. Since the promulgation of the Environmental Protection Agency (EPA) New Source Performance Standards (NSPS), it has become apparent that all US coals will require sulfur removal to comply with the new sulfur dioxide emission levels. If more stringent emission standards are imposed, through pending acid rain legislation or amendments to the Clean Air Act, it is likely that the coal industry, and the industrial and utility sectors will look increasingly toward the development of new and advanced coal cleaning technologies to continue and promote the use of coal. Table 1 summarizes the EPA NSPS for sulfur dioxide emissions. Fortunately, the basis for determining sulfur dioxide removal is the Btu and total sulfur content of the run-of-mine coal. Thus, credit is given for any sulfur removed before combustion, e.g., through physical coal cleaning. Unfortunately, physical coal cleaning alone may be unable to produce a compliance coal with respect to the EPA NSPS. Therefore, all industrial and utility coal-fired boilers will require post combustion gas cleanup, e.g., flue gas desulfurization (FGD), to comply with the new regulations. Table 1 - EPA NSPS for SO2 Emission Category SO2 Content of ROM Coal SO2 Reduction Required 1 0-2 Ib/M Btu 70 2 2-6 Ib/M Btu To 0.6 Ib/M Btu (70% to 90%) 3 6-12 Ib/M Btu 90% 4 12 Ib/M Btu To 1.2 Ib/M Btu Alternatives to post combustion gas cleanup, such as staged combustion, lime and coal injection, fluidized-bed combustion, and chemical coal cleaning, are currently under development. Of these, chemical coal cleaning offers the advantages of providing (1) high quality fuel for combustion (low sulfur and ash, high Btu, and attenuated product variability); (2) a solid fuel product for use in retrofitted gas and oil boilers; and (3) a solid fuel product with multiple end uses, e.g., internal combustion engines, carbon electrodes, coke, or chemical feedstock. Gravimelt process In the Gravimelt process, 1.4 mm x 0 (14 mesh x 0), physically beneficiated coal of about 5% moisture is fed into a 3401 to 3901 C (644 ° to 734 ° F) molten bath of sodium hydroxide and potassium hydroxide. Organic and pyritic sulfur and most of the mineral matter in coal react with and are dissolved in a molten mixture of potassium hydroxide and sodium hydroxide. The reacted coal sulfur is converted to alkali sulfides and polysulfides, whereas the mineral matter is apparently converted to alkali-aluminum silicates and other byproducts that are water and acid soluble. Coal residence time is 60 to 240 minutes. The sodium hydroxide to potassium hydroxide ratio is about 9:1. The total hydroxide-to-coal ratio is no less than 10:1. The specific gravity of the caustic melt is about 1.8 g/cm3 . Thus, coal is buoyant in the bath, and insoluble mineral matter with density greater than 1.8 g/cm3 would sink. Reacted coal is first water-washed with an equal weight volume of water in a countercurrent mode of operation. The coal is filtered and the filtrate sent for regeneration. The coal is then acid-washed in 10% sulfuric acid. The acid-water/coal mixture is filtered to recover the final coal product, and the filtrate treated with lime to precipitate dissolved mineral matter. The precipitate is filtered from the mixture and discarded. The water is recycled to the plant. Filtrate from water-washing is treated to remove sodium sulfide. The sodium sulfide is chemically treated to produce hydrogen sulfide, calcium car¬bonate, sodium hydroxide, and other products. The hydrogen sulfide is treated to produce sulfuric acid for the acid-washing step. The calcium carbonate is treated further or discarded, and the sodium hydroxide is concentrated by evaporation and recycled to the reactor. The Gravimelt process is currently at the bench-scale stage of development. A 0.9-kg (2-lb) continuous reactor is in operation with a continuous water- and acid-washing section adjacent. The regeneration section is not developed to a meaningful extent, although key reactions have been tested in the laboratory. Process conditions, product recovery efficiencies, etc., however, have not been determined adequately and continuous regeneration operation has not been attempted. Work is now in progress to develop each section to a continuous bench-scale operation in processing coal at 9.1 kg/h (20 lb per hr). Microwave process The carbon and hydrogen in coal are relatively transparent to microwave radiation. However, water, caustic, pyrite, and other mineral matter components are strong conductors of microwave radiation energy at the proper frequency. As a result, selective heating of the noncarbonaceous materials occurs that enables the chemical reaction of sulfur and ash with caustic. Although very high temperatures may result from

Jan 1, 1987

By James T. Tanner

Mica is a generic term that applies to a group of complex aluminosilicate minerals that have a sheet or plate-like structure and with different chemical compositions and physical properties. All micas form flat six-sided monoclinic crystals with remarkable cleavage parallel to the direction of the large surfaces, which permits them to be split into optically flat films; as thin as 1µm in thickness in some cases (Rajgarhia, 1987). Some micas are more easily split than others. For example, muscovite mica found in pegmatites is more easily split into thin films than is phlogopite. Mica found in mica schist is not as easily delaminated as mica found in weathered pegmatites. According to Dawson (1 949), the commercially important mica minerals are: Muscovite-potassium mica (colorless to pale green and ruby) Biotite-magnesium-iron mica (dark brown to black) Phlogopite-magnesium mica (pale yellow to dark brown) Vermiculite-hydrated biotite or magnesium-iron-mica (bronze yellow flakes) Lepidolite-potassium-lithium mica (pale lilac to deep purple) Some micas of less importance are: Zinnwaldite-lithium-iron mica (gray to smoky brown) Roscoelite-vanadium-potassium-magnesium mica (various shades of green and brown) Mica, principally muscovite, is widely used for industrial applications because of its exceptional physical, chemical, electrical, thermal, and mechanical properties (Table 1). Phlogopite and vermiculite follow muscovite in importance. Biotite finds very little commercial application at the present time. Commercially, mica is used in a number of forms. These forms and their description follow: Sheet mica refers to books of mica either mined from hard rock (pegmatites) or from loosely consolidated clayey material formed from the weathering of pegmatites and alaskites. These books can be readily split into thin film or splittings with specific thicknesses ranging from 0.0031 to 0.10 mm (Davis, 1985). Quality sheet mica is graded into 10 quality classifications (Tables 2 and 3). Books of mica that are flawed with excess inclusions, cracks, or folds (A mica) are called scrap mica and are either ground into commercial products by a dry or wet process. Built-up mica was developed in 1894 as a result of the cost and scarcity of sheet mica, and because many satisfactory electrical parts could be made from it (Preston, 1971). This type mica is formed by layering pieces of mica splittings upon one another and binding them together with inorganic or organic binders. These sheets are then pressed together under high temperature. Mica for this process is produced from pieces of sheet mica too small to be punched into electrical parts (Davis, 1985). Reconstituted mica is mica paper produced by forming a mat of very thin delaminated flakes of scrap mica. This mat is usually impregnated with an organic binder, but is also available unimpregnated. It is dried at 110°C. The mica for this process is either produced from the trimmings of a sheet mica operation or from blocks of A type mica (Davis, 1985, Chapman, 1983). Ground mica constitutes by far the largest use of mica, both quantitatively and application wise. It is produced by grinding and sizing scrap mica (also mica concentrate) obtained from five sources, 1) trimming from sheet mica, 2) A type mica blocks, 3) as a byproduct of spodumene and feldspar mining, 4) weathered pegmatites and alaskites, and 5) metamorphic schists. Synthetic mica is produced by crystal growth in a slowly cooled melt of accurately proportioned chemical oxides. Extended cooling times at a specific viscosity result in larger crystals. Many different micas have been formed by this process; however, fluorophlogopite is the most common.

Jan 1, 1994

By D. Tolgyesi, L. P. Gignac

Mine development has evolved in the past 15 years from a human-paced system using hand-held drills and track-bound equipment to a mechanized system using specialized equipment for each component of the development cycle. In most Canadian hard-rock mines, face advance is achieved by the following sequential activities: drilling, explosive loading, mucking and ground support. The state-of-the-art for each work element is reviewed and methods for performance estimates proposed. The entire development system and its production capabilities are considered based on equipment reliabilities, spare units, haulage distances, and muck bay spacing. The effect of the number of working faces on the system's performance will also be analyzed. Manuscript not received in time for publication.

Jan 1, 1983

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By R. Mensah-Biney

The aqueous biphase separation process (ABS) has been used to separate ultrafine industrial minerals. The partition behavior of TiO2, Al2O3, Fe2O3 and kaolin was not pH dependent. The partition behavior of SiO2 was, however, pH dependent. The partition coefficient of kaolin in PEG 3400/ Na2CO3 biphase system was = 150 and that of the silica in the same system was = 0.02, resulting in a separation factor of = 8500 between kaolin and silica. The aqueous biphase separation system was used to separate free silica from kaolin in a raw clay sample from Mexico. The partition behavior of mica, feldspar and clay from North Carolina was also evaluated.

Jan 1, 1999

By Randall Smith, Leslie Stayner

At the request of the Mine Safety and Health Administration, a quantitative assessment of the risk of lung cancer associated with occupational exposures to diesel exhaust was performed. This assessment was primarily based upon the results from a study of the effects of chronic inhalation exposure to diesel exhaust in Fischer-344 rats (previously reported by Mauderly et al., 1987). An adaptation of the Armitage-Doll multistage model, which allows for an age-dependent effect of exposure, was used to model the tumor response data. This model was fitted to all tumors (benign and malignant), and to malignant neoplasms alone. Estimates of unit risk (potency) were derived based upon a linear approximation to the results from the multistage model. A biologically equivalent dose was developed to scale the results from airborne exposure in rats to humans, which was adjusted for differences in weight, ventilation rate, deposition fraction, and the percentage of time actually exposed. Comparisons are made with risk estimates derived from modeling other rat inhalation bioassays and from applying different models to the study by Mauderly et al. (1987). We emphasize that our risk estimates are based upon a series of assumptions and carry a great deal of uncertainty. In particular, uncertainties regarding the effects of exposure on lung clearance mechanisms, the deposition rates in humans, and the relevance of our exposure index limit our confidence in these risk estimates. Because of these uncertainties, this risk assessment would best be viewed as an exploratory effort. Key words: Diesel, lung cancer, risk assessment

Jan 1, 1991

By K. J. Reid

With the current trends of increasing costs and decreasing head grades the mineral industry is no longer operating in very high profit areas and has been forced to pay greater attention to the application of modern technology. Although here are many technological advances to the credit of the industry in recent years there are still many processes being operated in the traditional manner and still many areas awaiting the application of methods which have been proven in other industries. Compared with the chemical industry the mineral industry is seriously ageing in the general areas of process analysis and process control, more so than can be justified by the complications arising from having to deal with particulate systems with properties far different from ideal, or even non-ideal, liquid systems. One area in which there has been a remarkable lack of application in the Mineral industry is that of analog computation and the authors feel that there is considerable scope for the use of the analog computer in studying mineral industry processes. The paper outlines the basic principles and features of the analog computer and describes its role as a simulation tool in some engineering and mineral processing systems.

Jan 1, 1972

By William S. Alldredge

The Washington Metropolitan Area Transit Authority(WMATA) officially came into existence in February 1967 after the District of Columbia, Maryland, and Virginia joined in a com¬pact pursuant to Federal creative legislation signed the previous November to build a regional rapid rail transit system called METRO (1). The parent organization was the National Capital Transportation Agency (NCTA), a Federal agency, subject to Federal statutes and regulations. Soon after the completion of the transition from NCTA to the new "non-Federal" status of the Authority, the Board of Directors of the Authority formally adopted procurement policies and procedures (2). These are specific statements concerning competition by formal advertising for bids or by solicitation of proposals for negotiation, contracting authority, approval of awards, awards of contract modifications, and processing of claims and disputes. These policies and procedures are silent as to Federal procurement statutes and regulations. But because of the Authority's origin, the sensitive nature of the compact among the several sovereign jurisdictions, Federal financing of two-thirds of the costs, and the resultant surveillance by the General Accounting Office over staff operations, the Authority's procurement practices follow closely Federal regulations adapted to WMATA's needs. This is an important point and is the foundation of contractual relations between the Authority as the owner and its construction contractors. Various constraints and flexibilities of this arrangement with respect to excavation and tunneling contracts will be pointed out in the ensuing discussions.

Jan 1, 1974

By N. Djordjevic

Introduction The vibration energy that travels beyond the zone of rock breakage is wasted - all it does is cause damage and annoyance. Under favorable geologic conditions, this energy may travel many kilometers before it finally drops bellow the background noise level. This has forced the introduction of more restrictive limits to the allowable vibration levels. To maintain the profitability of a mine or quarry and to comply with environmental protection legislation, blasting needs to be performed in a more predictable way that will ensure that the final results are optimal in both mining and environmental terms. Minimization of ground and induced structural vibration is, therefore, a matter of good blasting practice -not just an attempt to avoid complaints from neighbors. A new approach to blast vibration minimization is presented. The method utilizes the existence of the local minimums in the frequency spectrum of single-hole blast vibration. The results are presented as a delay map showing maximum ground or structural vibration velocity for many combinations of interhole and interrow delays. A blast engineer can use this map to select an optimal combination of delays that will produce a low vibration velocity at a selected location and, at the same time, will be acceptable from the point of view fragmentation or muck pile shape. Response of structures A typical single-story building has two distinctive forms of vibration. The first form is a translatory vibration of the building superstructure (frame), and the second form is a flexural-bending vibration of the structural elements such as walls and floors (Siskind et al., 1980). Walls and floors will have several modes of oscillation. The most important is the fundamental mode of the vibration, as this mode will have the lowest frequency, the largest amplitude and will cause the largest deformations. The vibration of walls and floors is also a source of secondary vibration within a building, due to the movement of loose objects, e.g., furniture and wall fittings (Dowding, 1985). The subjective estimate of the amplitude of a vibration by the occupants of a house will be unrealistically high due to the effect of the secondary vibrations. It is now well recognized that human perception of ground vibration begins at levels that are far below those that will produce minor damage to the most fragile structures. In mining and quarrying operations, complaints regarding vibration levels tend to be determined more by human perception or annoyance rather than by observations of damage. Ground vibrations on the order of 0.08 mm/s (0.0032 ips) (Walter and Walter, 1979; Murray, 1987) can be felt, and they are often subjectively estimated to be about 100 times greater. Amplification of ground vibration in the structure depends on the amount of energy in the ground vibration spectrum that is in the vicinity of the structure's resonant frequencies together with the damping ratio of the structure at these particular frequencies. One way to avoid significant vibration amplification in a structure is to shift the dominant part of the ground vibration away from the resonant frequency range of the structure. The presented method allows for the selection of the optimum blast timing (interhole and interrow delay times) to minimize the resultant ground vibration amplitudes in a given frequency range. It also allows the selection of suboptimal, but still acceptable, blast delay times, which may be preferable from the point of view of overall blast performance. Determining frequency ranges of importance in structures In attempting to avoid amplification of vibrations in the structure, ground vibration amplitude of frequencies close to the resonant frequencies of the building needs to be minimized. The width of the frequency-minimization region is determined by the value of damping in the building. If the damping ratio is low, then the frequency-minimization region around the resonant frequency will be relatively broad. By shifting the dominant part of the ground-vibration energy into the frequency region much higher than the resonant frequency of the building (1.5 to 2 times), it is possible to achieve efficient vibration isolation of the building. In such cases, the structural dynamic amplification of ground vibration will be less than unity. The first step in this minimization process is the determination of the structural resonant frequency. From the frequency spectrum, it is possible to determine the resonant frequency of the structure. Sometimes the

Jan 1, 1998

By Khosrow Badiozamani

Operating mines in Wyoming and Montana, which are generally characterized by shallow overburden and thick coal seams, are faced with reclamation problems which are unique to this area. Unlike the eastern or midwestern mines, removal of thick coal seams and lack of sufficient overburden creates overburden deficiencies that require careful evaluation prior to mining to insure compliance with regulatory requirements. Computer models and computer graphics can assist in such evaluation where appropriate alternatives can be selected which satisfies both the regulatory requirements and minimizes cost. This paper presents one such model used in evaluation of backfill requirements for restoration of surface and ground water regimes, restoration of mined-out areas to the approximate original contour, and the blending of the mined-out areas to the surrounding topography.

Jan 1, 1981

By T. A. de Almeida, M. de Paiva Bueno, M. Powell

The mining industry is one of the foundations of modern society, providing not only the raw materials needed to maintain a contemporary lifestyle, but also serving as a basis for the development of future technologies. From the most basic components of an appliance to the materials needed to design an electric car or a space rocket, each raw material has gone through a painstaking procedure of extraction and processing, and ways to make this process more efficient will be of great help to meet an ever-increasing demand for minerals. One of the biggest challenges when extracting mineral resources is to measure the variability of the mineral body prior to processing. Comminution is the most power-demanding stage, and the lack of geometallurgical testing, often for financial reasons, may result in an inefficient operation. The Geopyörä Rock Breakage test was developed with the objective of making mineral variability data more accessible by providing both standard comminution parameters and rock mechanical properties at low cost, and with a modest sample size, allowing a larger number of samples to be tested to reduce uncertainties and assure productivity. The objective of this paper is to present the results of an extensive validation of this new rock breakage method against two of the main tests currently in use, namely the SMC® and Bond ball mill work index tests. More than 100 samples have been tested and the results compared, showing that the new method can accurately estimate the parameters of the traditional tests. This confirms that the new test is a reliable tool for comminution and geometallurgical tests.

Feb 1, 2023

By J. Swensen, R. Brandon, A. Wallstein, S. Bessinger, J. Pile

It is generally agreed that C.C. White was the first to describe and market coal mine roof trusses beginning as early as 1967. White was issued a patent in 1969 1. Coal mine roof trusses were extensively used in the 1970’s, and their use has proven valuable in many difficult conditions. Beginning in the mid 1990’s, several types of bar/cable trusses have been introduced. A new and innovative bar/cable truss recently introduced offers several advantages. By eliminating many small parts, and simplifying the installation, these new trusses are much easier and faster to install, thereby increasing operator safety.

Jan 1, 2004

Underground instrumentation and observations at longwall panels have demonstrated that the growth of main roof causes an extremely high roof weighting on the shields. It can sometimes result in catastrophic effects on the support when the roof weighting intensity far exceeds the support capacity. In this paper, a comprehensive study was conducted on characteristics of main roof breakage and its effects on shields at different locations, based on the monitored shield data, theoretical analysis, and finite element analysis. With the help of theoretical analysis and numerical modeling, stress distribution and redistribution in the main roof were analyzed in detail to define main roof failure modes and understand the maximum roof weighting intensity imposed on the shields. From this study, it was found that the effects of main roof breakage on shields are chiefly related to the shield initial setting condition and the final failure mode of the main roof.

Jan 1, 1994

By Joseph W. Johnson

General Electric introduced electric drive systems on 85 ton Off-Highway mining trucks in the early sixties. Due to favorable economics, trucks have increased in size to handle larger payloads. Series Motorized Wheel systems were developed to meet this demand. When the technology was available, General Electric switched from use of Series motors to separately excited motors with the added benefits of static exciters and simplified control. Over 20 years of electric drive experience have been incorporated in the STATEX drive systems, which covers truck sizes from 85 to 220 tons. This paper traces the drive system developments from the early stages to the present and takes a look at what's ahead.

Jan 1, 1983

By Theodore H. Eyde

In 1971, the Minerals Division of The Superior Oil Company acquired exploration rights to an unpatented claim group in the Superior (Pioneer), Arizona mining district, lying west of the Concentrator fault. This major post-mineral fault displaces the Magma vein-fault, which is mined in the Magma Mine at Superior, Arizona. The Magma vein-fault and the enclosing section of pre-mineral rocks consisting of Paleozoic and younger Precambrian sediments and diabase, is overlain by a thick section of post-mineral rocks, consisting of the Gila conglomerate, the Apache Leap dacite, and the Whitetail conglomerate. Geologic information on the thickness and attitudes of the rocks obtained from previous diamond drilling indicated that the section of post-mineral rocks might be from 3,000 to over 4,010 feet thick in the target area. (Figure 1) The Magma vein-fault is a steeply dipping vein which has produced nearly a billion dollars of copper, zinc, silver, and gold. It has been mined continuously for nearly 10,000 feet along the strike and nearly 5,000, feet vertically down the dip. It ranges from less than a foot to over 50 feet wide and contains sulfide mineralization con¬sisting of pyrite, chalcopyrite, bornite, and chalcocite.

Jan 1, 1973

By Gary Brieley

Until well into the 20th century, most construction work was performed under the auspices of a master builder or in a manner that would be described today as design-build. In addition, many civil engineers served as ?interns? under the tutelage of a master builder in order to learn how to design and construct a certain type of structure. This was certainly the case for tunneling projects with various individuals having been identified as tunneling experts as a result of successfully completed projects The master builder approach began to change in the early 1900s to a model that would be referred to today as design-bid-build. A design-bid-build approach to project procurement gives the owner more control over the final product and al-lows the contractor to know exactly what is expected of them before the work is constructed. As a result of this transition in project procurement, civil engineering schools placed a greater emphasis on the training of ?design? professionals. This article will document how the training of tunnel design professionals progressed within the United States. Although it is difficult to generalize about the hundreds of tunnels that were constructed in the first four decades of the 20th century, there is one project that stands out as having resulted in a university program related directly to tunneling and that is the Chicago Subway. During a visit to the United States in 1938, Dr. Karl Terzaghi met a student named Ralph Peck who was then studying at Harvard University in a pro-gram established by Arthur Casagrande. Shortly thereafter, Terzaghi traveled to Chicago for a lecture and was asked to consult on the Chicago subway project that was then under construction. The Chicago subway was being constructed in clay, and the owners were worried about possible settlements to nearby buildings. Terzaghi asked Peck to serve as his field engineer for that project. Thus was established one of the most productive relationships in the history of civil engineering in the United States. Peck, who would become Dr. Peck, moved to Chicago in 1939 to participate in an extensive research project that con-tinued until subway construction was halted in 1941 because of World War II. During that time, the cost of subway construction in Chicago was reduced substantially as a result of Peck?s observations and Terzaghi?s recommendations. In fact, it was reported that subway construction in Chicago cost less than one-half of similar projects in London even though the clay in London is considerably stiffer compared to Chicago. Upon the completion of his work on the Chicago Subway, Peck accepted a professorship with the University of Illinois in Champaign/Urbana.

Jun 1, 2010

By J. J. Komadina

Since the advent of resin-in-pulp (RIP) technology for treatment of uranium-bearing ores in the 1950?s to current carbon-in-pulp (CIP) processing of gold values, metallurgies and operators alike have wrestled with the problem of interstage screening. Early gold CIP plants such as at Homestake utilized externally mounted vibrating screens in conjunction with air lifts to effect carbon-pulp disengagement. Other operations world-wide have likewise adopted this technique with varying degrees of success. Subsequent development of in-tank launder screens both in South Africa and the United States have been of the air cleaned variety (EPAC)

Jan 1, 1988

By H. Kiyama

In order to further elucidate the mechanisms involved in autogenous grinding, the fracture of rock specimens in free-fall impact was studied using the theory of elasticity. Stress distributions in rock specimens under various conditions of impact were analyzed and the conditions for failure were examined in relation to the compressive and tensile strength of rock. The energy equation derived for autogenous grinding coincides basically with Lewis' generalized formula or Oka and Majima's formula, and it is sufficiently general to incorporate all of the three older theories, viz; those of Rittinger, Bond and Kick.

Jan 1, 1972