Search Documents

By E. Milke, A. Arnold, B. Friedrich, A. Sydykov

CaF2is often used as a fluoride addition to the chloride salt flux in the melting of aluminium scrap. The solubility of CaF2in the chloride salt system is limited. Dissolved CaF2is considered to improve the properties of salt fluxes. Experimental investigations indicated that the solubility ofCaF2in 70 wt % NaCl/30 wt % KCl, German salt flux used in aluminium scrap melting, might be lower than expected according to literature data. The pseudo binary section CaF2-(70 wt % NaCl-30 wt % KCl) was investigated by differential thermal analysis (DTA). The determined solubility of CaF2appeared to be considerably lower than presented in the literature. The pseudo binary section calculated using thermodynamic data partially confirmed the results. DTA allowed us alsoto determine the crystallization temperature interval of the two phase eutectic consisting of the solid solution NaCl-KCl and CaF2. Keywords: aluminium recycling, phase system, salt flux, CaF2, NaCl, KCl, solubility

Jan 1, 2004

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

By M. E. Rossi

All large-scale applications of conditional simulations intend to benefit from the ‘correct’ (or’ accurate’) characterization of uncertainty, adequately describing the variability observed from the data and its impact on the final objective. This paper discusses a number of relevant issues that highlight the extent to which, in reality, a model of uncertainty is dependent on the random function model chosen. Often in the presence of large number of conditioning data most available random function models will provide similar models of uncertainty. When conditioning is scarce, the resulting models of uncertainty will vary more widely, since the final output will depend mostly on the underlying assumptions of the model chosen. The application described in this paper is taken from a large porphyry Cu operation in northern Chile, and it demonstrates the impact of several variables on the resulting models of uncertainty. In particular, some of the decisions involved include the number of conditioning data and the underlying Random Function model used (Gaussian or indicator-based). Also, implementation-specific parameters must be decided upon, such as grid size used, random number generator, simple or ordinary kriging, multiple-grid simulation, and simulation of irregular three-dimensional bodies (as opposed to regular grids). Some practical guidelines are proposed to deal with these decisions.

Jan 1, 2003

By J. Forwood

The Youga gold mine in Burkina Faso, West Africa, is scheduled to produce first gold in the third quarter of calendar 2007. The project is expected to produce 540 000 oz of gold over 6.5 years, from a conventional open pit carbon in leach mine. The direct capital cost of the project is US$47 M. Etruscan Resources Inc, a Canadian based gold exploration and development company, holds 90 per cent of the project company Burkina Mining Company SA (BMC). The state of Burkina Faso is free-carried for the remaining ten per cent of BMC. RMB Resources Limited, of Melbourne Australia, has arranged a US$35 M project finance facility for BMC (the Borrower) as the majority of funding for the Youga project development. The loan facility was provided by RMB Australia Holdings and Macquarie Bank Ltd (the Lenders) each as to 50 per cent in the lending syndicate. The Lenders also provided a gold hedging facility to guarantee a minimum price for the project's gold production. Burkina Faso is a francophone country, part of the Economic and Monetary Union of West Africa (UEMOA). The project financing is the first such facility to be arranged for a mining project in Burkina Faso, with little or no precedent available in other UEMOA countries. Therefore, while the Youga gold project is forecast to be a robust project applying conventional mining and processing methods, a number of legal, technical, commercial and social issues required identification, evaluation and resolution before the loan could be established. This paper describes that evaluation process and the resolution of these issues. In-house experience and expertise in both the Lenders' and Borrower's teams has facilitated a greater understanding and `ownership' of the issues and hence provided comfort with risks which might not normally be taken in conventional project developments and project financings. As a result, blanket external reviews were not required by the Lenders. A long-standing relationship between Etruscan and RMB Resources also facilitated solutions to a number of issues. Nevertheless, a degree of flexibility by the Lenders, the Borrower and Etruscan was required to successfully close the financing.

Jan 1, 2007

By S. Okubo, K. Fukui

Empirical equations established for estimating the rock strength of the working face based on the cutting forces of a tunnel boring machines (TBM) are further examined and discussed with respect to the dominant factors affecting TBM performance. Constants in the equations are related to TBM-specific parameters such as excavation (tunnel) diameter, cutter diameter, and cutter distance. The relationship between the constants and the TBM specifications is examined in this study on the basis of data collected at ten tunnels, and it is found that the constants are most strongly influenced by the cutter diameter and tunnel diameter. Zur Schätzung der Gesteinsfestigkeit an der Arbeitsfläche ermittelte empirische Gleichungen, die auf den Schneidekräften von Tunnelbohrmaschinen (TBM) beruhen, wurden weiter im Hinblick auf die vorherrschenden, die Leistung der TBM beeinflussenden Faktoren hin untersucht und diskutiert. In der Gleichung enthaltene Konstanten werden zu den TBM-spezifischen Parametern wie Auschachtungs- (Tunnel) Durchmesser, Schneidendurchmesser und Schachtlänge in Beziehung gesetzt. Die Beziehung zwischen diesen Konstanten und den technischen Daten der TBM wird in dieser Studie auf der Basis der bei 10 Tunnelbauten gesammelten Daten untersucht. Dabei wurde gefunden, dass diese Konstanten am stärksten von den Durchmessern der Schneiden und der Tunnel beeinflusst werden. Cette étude examine et discute les équations empiriques permettant d'estimer la résistance de la roche attaquée aux forces de coupe des tunneliers dans le cadre de l'étude des facteurs dominants affectant les performances des tunneliers. Les constantes de ces équations concernent les paramètres spécifiques des tunneliers comme le diamètre d'excavation (du tunnel), le diamètre du couteau et la distance de coupe. Cette étude examine le rapport entre ces constantes et les caractéristiques techniques des tunneliers d'après des données collectées dans dix tunnels et elle conclut que ces constantes sont principalement influencées par le diamètre du couteau et le diamètre du tunnel.

Jan 1, 2003

By P. K. Hofmeyr

Base Metal (Cu, Ni, Mo, Zn, Co etc.) analysis traditionally has been very slow in conventional analytical laboratories which can lead to additional costs being incurred in waiting time of drill rigs or mining excessively off-reef. Recent developments in the automation of analytical laboratories now allow for very rapid turn-around times for base metal analytical data which can help reduce such costs as well as reduce the unit costs of the analyses themselves. 2.0 CONVENTIONAL ANALYTICAL LABORATORY PRACTICE Conventional analytical laboratories are necessarily are very manual. Sample preparation is slow and laborious, samples are moved from stage to stage manually and, typically, all samples are processed in batches so a sample which is the first to be, say, milled has to wait for the complete milling of the batch before it advances to the next stage eg. mixed with wax prior to pelletising for XRF analysis. Inevitably this results in long sample data turn-around times for laboratories handling large numbers of samples. Manual sample preparation can only be accelerated by increasing staff which increases costs and can lead to additional errors being introduced. Cleaning of sample preparation equipment, eg. crushers and mills, between samples is essential to avoid cross-contamination between samples and this is slow and labour-intensive. In manual sample preparation the correct sample numbers staying with the samples is totally dependent on the efficiency of laboratory operators. It is extremely difficult to detect when errors have occurred due to the switching of sample numbers during the sample preparation stages. Running duplicates and QC samples at best is only partially successful in detecting when sample number switching errors have occurred. Errors of this nature and cross-contamination problems due to incomplete cleaning of sample preparation equipment tend to occur when laboratories are working at pressure due to high sample numbers and when supervisors are not present during 24/7 laboratory operations which is often required on plant process control laboratories. These problems are common to all conventional analytical laboratories and their magnitude is dependent on the level of control and efficiency of QC systems practised by individual laboratories. The disadvantages of conventional manual analytical laboratories can be summarized as follows:- 1. Labour-intensive which is costly especially when multiple shifts have to be used during 24/7 operations.

Jan 1, 2005

By D. F. Malan, M. Grave, J. A. L. Napier

Previous fundamental research projects have indicated the value of continuous closure measurements in deep tabular excavations for improved support design, hazard assessment and for quantifying the effect of seismicity on stope closure. This paper describes further measurements in a VCR stope to validate some of the earlier findings. Calculation of the closure ratio showed that it is a good measure to identify different ground conditions and possible hazards. This work was supported by numerical modelling results, which showed that the closure ratio is very useful in discriminating the response of different geotechnical environments. Des projets précédents de recherche fondamentale ont démontré la valeur de mesures continues de fermeture dans le cas de profondes excavations tabulaires pour une conception améliorée du soutien, de l’évaluation du danger et pour quantifier l’effet de la séismicité sur l'affaissement du toit d’un chantier d’abattage. Le présent document décrit d’autres mesures dans un chantier d’abattage VCR afin de valider certaines des conclusions précédemment formulées. Le calcul du degré d'affaissement montre qu’il y va de soi d’identifier différentes conditions de sol ainsi que les dangers possibles. Les présents travaux ont été confirmés par des résultats de modélisation numérique, lesquels ont démontré que le taux d'affaissement est très utile quant à discerner la réponse dans des environnements géotechniques différents. Vorherige Forschungsprojekte haben den Wert von kontinuierlichen Setzungsmessungen im tiefen Sudafrikanischen Strebabbau angedeutet, vor allem fur Ausbaudesign und Risikobewertung, als auch fur die quantitative Bestimmungen der seismizitatsabhangigen Setzung. Dieses Referat beschreibt weitere Messungen in einer VCR Grube um fruhere Bestimmungen zu bewerten. Dass errechnete Konvergenzverhaltniss erweiste sich als eine gute Massnahme zur bestimmung von geotechnischen Zonen und moglichen Risiken. Numerische Analyse unterstutzte die vorliegende Arbeit und deutete darauf, dass das Konvergenzverhaltniss sehr brauchbar ist um Verhaltensunterschiede der geotechnischen Zonen zu erproben

Jan 1, 2003

By M. K. Elmouttie, G. V. Poropat

The analysis of structure using joint set statistics is well known. Other data such as the position of discontinuities and the contacts between rock mass units cannot be easily incorporated in simple statistical analysis based on orientation alone. Algorithms to model the structure of rock slopes using measurements of the orientation and position of discontinuities are being developed by CSIRO Exploration and Mining. These algorithms provide a capability to model the structure of a rock slope and estimate the likelihood of the formation of hazardous blocks in existing or proposed rock slopes and identification of the location and size of these blocks. The algorithms provide the basis of structural modelling to identify potential failure mechanisms in rock slopes.

Jan 1, 2006

By C. Erichsen, J. Werfling

ABSTRACT: A three-dimensional elastic constitutive model for rock salt is proposed. This stress strain law takes into account the three phases of creep (transient, steady state and accelerated creep), dilatancy, as well as the failure and post failure behaviour. The model was implemented into a finite element program and validated on the results of laboratory tests and in situ measurements. A good qualitative and quantitative agreement with the test and measurement results is achieved. A stability analysis for an underground repository in rock salt is presented. ZUSAMMENFASSUNG: Es wird ein dreidimensionales elastisch-viskoplastisches Stoffgesetz für Steinsalz vorgestellt. Mit diesem Stoffgesetz können die drei Kriechphasen (primäres, sekundäres und tertiäres Kriechen), Dilatanz sowie das Bruch- und Nachbruchverhalten erfaßt werden. Dieses Modell wurde in ein Rechenprogramm, das auf der Methode der finiten Elemente basiert, implementiert und an Ergebnissen von Laborversuchen und in-situ-Messungen validiert. Die Versuchs- und Meßergebnisse lassen sich mit diesem Stoffgesetz qualitativ und quantitativ gut nachvollziehen. Als Anwendungsbeispiel wird der Standsicherheitsnachweis für eine Untertagedeponie im Steinsalz erläutert. RÉSUMÉ: Cet article présente un modéle constitutive élastique/viscoplastique à trois dimensions pour sel gemme. Ce modéle comprend les trois stade de fluage (fluage primaire, secondaire et tertiaire), la dilatation, le comportement de défaillance et d'après défaillance. Il est implanté dans un programme de calcul aux éléments finis. À l'aide des essais laboratoire et des mésures in situ, le modéle a été validé. Les résultats des essais et des mesures concordent qualitatifs et quantitatifs aux résultats des calculations.

Jan 1, 2003

By F. T. Cawood

Inauguration of the new political dispensation in South Africa in 1994 initiated a dynamic shift in the ownership, management and development of the country’s affluent mineral heritage. The process of substituting the old South African regime with a new equitable system, started soon after the 1994 election of the African National Congress (ANC) to parliament. The Congress’ Freedom Charter revealed the intent of the new dispensation when it called for radical transformation of mineral development. However, since 1955 there have been important changes affecting the rules of mineral development. These are: •Firstly, a drastic change in politics ushered in by negotiation, a spirit of reconciliation and a desire to settle disputes peacefully •Secondly, the globalization of the South African mining industry in tandem with the opening of domestic mineral resources to foreign capitalists; and •Thirdly, the introduction of sustainable development as a holistic approach to mineral development in order to replace traditional narrow-minded environmental management. Each of these significantly shaped the new mineral investment environment of South Africa. This paper represents a summary of the historical developments leading to the current Mineral and Petroleum Resources Development Act No. 28 of 2002, its Regulations, the much-publicised Broad-Based Socio-Economic Empowerment Charter and its associated Scorecard.

Jan 1, 2003

By Michelle Mouton, Johanna van Deventer, Jussi Vaarno

Mintek has been involved in numerous projects to remove Fe and Mn from dilute Co sulphate solutions by means of oxidative precipitation using air/SO2. Test work was done using a gas induction system, designed and supplied by Outotec. Various aspects, such as SO2 concentration, SO2 flowrate, impeller rotation speed and pH were investigated on a 2 m3 scale. Batch tests were performed using a residence time of 5 hours. Mintek has been involved in numerous projects to remove Fe and Mn from dilute Co sulphate solutions by means of oxidative precipitation using air/SO2. Test work was done using a gas induction system, designed and supplied by Outotec. Various aspects, such as SO2 concentration, SO2 flowrate, impeller rotation speed and pH were investigated on a 2 m3 scale. Batch tests were performed using a residence time of 5 hours. Impeller rotation speeds of 0-220 rpm were tested, and it seemed that speeds of between 80 and 220 rpm gave similar Fe and Mn removal rates. Co and Cu losses were generally below 1% and 5% respectively at pH 3.

Jan 1, 2007

By B. Amadei, F. Tonon

Rock stress measurement is cast in the more general context of the determination of boundary conditions for rock engineering. A study on the effect of elastic anisotropy on underground excavations reveals that this effect is actually controlled by the imposed boundary conditions. Applications to tunneling and to the Underground Research Laboratory (URL), Canada, exemplify a procedure for boundary condition estimation formerly developed by the authors. The procedure displayed fast convergence despite the complex geometry, and the high degree of non-linearity of the models. In the URL application, the 3-D model was able to completely reproduce the complex measured stress pattern, and the 90° rotation of the principal in situ stresses with depth. In order to reliably estimate the boundary conditions reproducing the current in situ state of stress, response measurements of the rock mass to current disturbances are necessary as input data. La mesure des contraintes in situ tombe dans le domaine général de la détermination des conditions aux limites pour les problèmes de mécanique des roches. Une étude sur le rôle de l’anisotropie élastique sur les excavations souterraines montre que ce rôle est contrôlé par les conditions aux limites qui sont imposées. L’application aux tunnels et au Laboratoire Souterrain de Recherche (URL) au Canada, nous permet de présenter une méthode de détermination des conditions aux limites. La méthode converge rapidement bien que le géométrie soit complexe et que le problème soit non-linéaire. Pour le URL, le modèle 3D est capable de reproduire la distribution des contraintes qui ont été mesurées ainsi que la rotation de 90 degrés des contraintes in situ avec la profondeur. Afin de déterminer avec précision les conditions aux limites responsables pour la distribution actuelle des contraintes, la réponse du massif rocheux doit être connue et mesurée. In der Felsentechnik sind die Spannungsmessungen in Gestein an die Bestimmung der Randbedingungen gebunden. Eine Studie legt dar, dass der Effekt elastischer Anisotropie in unterirdischen Aushoehlungen von den Randbedingungen kontrolliert ist. Eine von den Authoren entwickelte Methode zur Bestimmung der Randbedingungen wird an Beispielen im Tunnelbau und im Underground Research Laboratory (URL) in Kanada illustriert. Auch bei komplexer Geometrie und einem hohen Grad an Nicht-Linearitaet zeigt diese Methode ein schnelles Konvergenzverhalten. Ein 3D-Model und dessen 90° Drehung der lokalen Hauptspannungen mit der Tiefe, kann bei einer URL Anwendung vollstaendig reproduziert werden. Um mit dieser Methode die Randbedingungen zuverlaessig abschaetzen zu koennen, werden der gegenwaertige lokale Spannungszustand sowie die Antwort des Gesteins und die resultierenden Stoerungen als Eingabedaten benoetigt.

Jan 1, 2003

By I. E. Teymenson, L. A. Bakhvalov

Irrational usage of mineral commodities leads to depletion of natural resources and various ecological violations in natural environment. Fulfilment of a number of measures and strategic decisions by given problems requires a correct forecast of trends of social-economic systems. For solving the task of long-term forecasting special procedures, considering Kondratyev’s big cycles of world conjuncture, have been embedded into algorithms of unknown parameters identification and recovering of factors of different countries mineral resources production and consumption models. In the paper the classification of long cycles types, existing forecasting algorithms on the basis of Kondratyev’s ‘long waves’ or ‘K-waves’ and the modified algorithm, developed by us, which allows to reduce time and financial expenses and to improve the forecast quality, are presented. Furthermore, the article includes several forecasts of mining branch corrected models factors, received by us, permitting complex prognosis of economic and social development of different scale and control level systems. In the paper workability of proposed forecasting algorithms on the base of ‘K-waves’ and adequacy of created models to researched processes are proved.

Jan 1, 2003

By B. Ndlovu

The world mineral industry has over the years experienced growth in the production of nickel (Ni) due to its use not only in the catalytic industry but mainly also to its demand in the stainless steel production industry. Hence there is a need to produce more pure and marketable grades of Ni through the use of efficient purification routes such as solvent extraction. The V10-LIX®84-IC system resulted in nickel (Ni) extraction isotherm shifting to lower pH levels. The pH window of opportunity for the extraction of Ni subsequently increased in solution containing magnesium (Mg) and calcium (Ca) even though the system also resulted in slight shifts to less positive pH values for Mg and Ca curves. Results showed a synergistic effect of LIX®84-IC when added to V10 for all elements, Ni, Mg and Ca. The pH50 values for elements Ni, Mg and Ca in the V10-LIX®84-IC system were 2.95, 8.10 and 7.70 respectively. Comparing results obtained when using V10 alone produced ?pH50 for Ni, Mg and Ca being 3.35, 0.15 and 0.70 respectively, which was a confirmation of the synergistic shifts for all the elements. The ?pH50 (Mg-Ni)value was 1.95 with no synergism and 5.15 with synergism and that for ?pH50 (Ca-Ni)was 2.10 with no synergism and 4.75 with synergism. This showed that the Ni-Mg separation factor was relatively larger than the Ni-Ca. Improved loading and stripping kinetics were also observed. Keywords: Nickel solvent extraction separation, magnesium, calcium, versatic 10 acid and LIX®84-IC.

Jan 1, 2008

By E. Dzingayi

Keywords: Pyrometallurgy, furnace, Bindura, nickel The smelter at Bindura Nickel Corporation processes concentrates from its own mines and other external sources. Concentrates are dried, smelted, and converted to a desulphurised matte (leach alloy) for further processing at the refinery. The smelter comprises a drying plant, submerged arc electric furnace, electrostatic precipitator, and three Peirce-Smith type converters capable of treating 150 000 tonnes of concentrates per year. Concentrates are dried in a rotary coal-fired kiln, blended with fluxes, and smelted in a six-in-line submerged-arc 15MW electric furnace. Slag is tapped and granulated for disposal, and matte is tapped at regular intervals for blowing in Peirce-Smith converters. The paper details the 37-year history of the smelter, including furnace rebuilds and operating parameters as they have evolved in response to changing feed compositions. Special challenges, particularly relating to the treatment of high talc concentrates, are also described.

Jan 1, 2006

By Dechun Lou, Benjamin Ravary, Merete Tangstad, Stein Wasbø, Sean Gaal

The melting phenomena of manganese ore, slag and alloys were studied in an experimental sessile drop furnace. Particles of approximately 20-60mg were placed on graphite substrates and then heated at a constant rate of 5°C/min up to 1830°C in a controlled gas atmosphere of Ar or CO. The shape of the particle was photographed with a digital video camera every second. It was observed that the melting behaviour can vary significantly, with some particles exhibiting a large softening/melting range. Selected samples were sectioned and then analysed with EPMA. The implications of the results on understanding industrial furnace operations are discussed.

Jan 1, 2007

By M. A. Jensen, J. J. Bettencourt

SYNOPSIS An analysis was made of records of accidents involving Bantu mineworkers and which resulted in either minor injuries or hospitalizations to determine patterns in underground accidents from which to formulate priorities in accident prevention in gold mines. The results showed that: (i) specific labour categories, such as inexperienced men, are exposed to certain types of hazards the extent of which warrant the separate design of safety programmes to meet their specific needs; (ii) the systematic study of minor accidents provides a dependable source of. information of which safety departments could make greater use in their efforts to control and prevent mining accidents.

By S. K. Murphy, K. B. Le Bron, A. K. Ward, S. Hayes, T. Rangasamy

A process for evaluating different options for extraction of mining blocks is presented. The process is described and an example of the application of the process to a case study is presented. Un procédé pour évaluer différentes options pour l’extraction de blocs d’exploitation est présenté. Le procédé est décrit et un exemple de l’application du procédé à un cas particulier est présenté. Ein Prozeß für das Auswerten der unterschiedlichen Optionen für die Extraktion von Abbaublöcken wird dargestellt. Der Prozeß wird beschrieben und ein Beispiel der Anwendung des Prozesses zu einer Fallstudie wird dargestellt.

Jan 1, 2003

By M. G. Wimberger

The Merensky Reef zone, as developed on Impala Platinum?s Rustenburg Operations, displays a gradational mineralized zone, with grades decreasing from the Merensky Pegmatoid Unit into the footwall and hanging wall. A system of identifying a manageable method of defining the mining cut is introduced, termed the grade profile attenuation cut-off grade. Although horizontal grade selectivity is not applied in the mining of the Merensky Reef zone, low extraction of the orebody, due to manageable and non-manageable factors, can contribute to a reduction in revenue, even losses, due to fixed cost contributions in the mining and beneficiation of the ore. A model is proposed that integrates all variables affecting the revenue of the mining operation, including the grade profile attenuation cut-off grade, the extraction factors, commodity prices and exchange rates, utilizing numerical simulation techniques in a PC-based environment. A breakeven extraction factor for a specific cut-off grade is delivered for a range of market conditions. The breakeven extraction factor is a useful guide when designing mining layouts in structurally complex and low metal content areas. Incorporating distribution functions for individual commodity prices and exchange rates into the model provides mineral resource managers with a risk profile for individual mining areas. Shaft areas have varying grade profiles and each area should have individual models run, to prevent generalizations being made about acceptable risk levels on mining areas.

Jan 1, 2004

By C. Steve

ABSTRACT: In this paper, the stability evaluation and bifurcation criteria are presented for the Jinping arch dam structure. The bifurcation models in failure status of the arch dam are derived from the uniqueness of the controlling equation of dam behaviours, and the relative phenomena between positive definition of dam structural tangent stiffness and bifurcation are given in the paper. Then the structural collapse criteria for arch dam are discussed based on the energy mode. A stability criterion of dam based on the connection of yield zones is proposed according to the implementation of elasto-plastic FEM (finite element method) numerical analysis. In accordance with this judging method, nonlinear FEM analysis is used for Jinping arch dam. The failure process of the Jinping dam was simulated and yield zones were found under the overloading condition. Keywords: Stability evaluation, bifurcation, failure process, Jinping arch dam ZUSAMMENFASSUNG: In der Verliegenden Arbeit wird ein integrater geomechanisch Modellversuch fuer Jinping Bogenstaumauer Vorgesstellt. Die Bogenstaumauer liegt aut der komplizerten felsformationen. Der Zerstoerungsmechanismus, die Stabilitaetsfaktoren und die Interaktion zwischen der Bogenstaumauer und den Seiltichen. In der Vorliegenden Arbeit wird eine dreidimensionale finite element analyse fuer die seitlichen. Gestein sauflager mittels dem Bruchmodell Vorgestellt, da fuer Jiniping Bogenstaumauer angewandet wird. Ein Bruch mechanismus model einschliesslich der statistischen parameter der Gesteinfes tigkeit wird entauckeit. RÉSUMÉ: Das ce documènt a été faite une analyse d’elemt limité de trois dimensions dn fondement de construction de roche faisant appel au modéle de l’endommagemnet à fracture, analyse appliquée an fondement du bar ragevoute de Jinping. Ce documènt décrit le test de modéle géomecanique intégral pour le barrage-voûte de Jinping L’ampleur du modéle en question constitute l’une de plus importantes en China. Ils correspondent par faitement anx calculs des résultats.

Jan 1, 2003