Search Documents

By M. W. John, I. D. Matthews

SYNOPSIS This paper describes the process adopted for the recovery of gold from a dump originating from clean-up operations at Durban Roodepoort Deep Gold Mine. The gold-bearing dump material was refractory in nature, not being amenable to cyanidation because of the high level of carbonaceous material present. The laboratory tests on the material involved particle-size and chemical analyses, a mineralogical examination of the material, preliminary tests, and optimization of the process for the treatment of the dump material. The preliminary tests included tests on roasting, flotation, pre-leaching, adsorbent-in-leach, and blinding. Of these options, carbon-in-leach showed the greatest potential. The rate of gold dissolution, the rate of gold adsorption by the carbonaceous material, and the ratio of carbon to pulp were then investigated. It was determined that the ratio of carbon to pulp necessary to yield a reasonable gold recovery resulted in a carbon loading that was not high enough for economic elution and regeneration. A process incorporating washing of the carbon with cold acid between adsorption cycles was tested, and reasonable gold recoveries and carbon loadings were obtained. Durban Roodepoort Deep Gold Mine piloted the conceptualized process and determined that it was economically feasible. Two Browns tanks on site were modified, and an acid-wash tank was installed. The capital outlay for the plant was recovered within some 3 months.

Jan 1, 1990

By M. D. G. Salamon

If a transition from one equilibrium state to another occurs during the course of mining, energy transfer takes place in the rock mass, which is assumed to be an elastic continuum. The energy components are defined as follows: the work done by external and body forces, W; the increase in stored energy in the mass, Uc; the strain energy in the rock mined during the transition, Urn; the work done on mine support or backfill, Ws; and the released energy, Wr. The energy balance is defined as (W + Urn) - (Uc + Ws) = Wr> 0, where the first set of components in parentheses represents the sources of energy, while that of the second corresponds to the known modes of energy expenditure and the component on the right is the unaccounted-for energy surplus, which must be released and dissipated in some form. The inequality Wr ~ Urn> 0 applies. Expressions for the energy components are derived first for the general case and then for the 'slit' modal used to simulate tabular excavations. Through specific examples, the importance of the progressive nature of mining is emphasized. The size of the steps used to enlarge the excavations appears to play a significant role in the mode of energy transfer. This observation forms the basis of the second paper in this series of two papers.

Jan 1, 1984

By M. Splaine, C. E. Dohm, S. J. Browner

As the grade of the gold (head grade) in the ore supplied to a reduction plants falls, the efficiency of recovery of the metal drops. This is not simply due to a fixed grade lost in the residue, since the residue grade is itself a function of the head grade. A multi-disciplinary approach was used in the construction of a model to represent the relationship between head grade and recovery efficiency. The model is a physicochemical one based on (i) the reaction characteristics of cyanidation, (ii) the milled-ore selection characteristics of gravity concentration, and (iii) the nearly log normal distribution of gold grades and particle sizes in ore reserves. The model was used to set sound target levels for recovery efficiency for a given head grade at a given plant, against which the performances of the plant equipment can be judged for control purposes.

Jan 1, 1982

By E. J. Magri

This paper describes a geostatistical study of the relative merits of diamond-saw sampling and conventional chip sampling, using results from experimental work carried out on Randfontein Estates Gold Mine and Western Areas Gold Mine. The diamond-saw sampling procedure is described, and it is concluded that this is a very efficient operation and leads to good-quality sampling that is clearly an improvement over conventional chip sampling. The study principally involved the computation of the errors of estimation of the mea gold value of mining panels for the two sampling methods, revealing that, in the normal production environment, the diamond-saw sampling method is a significant improvement over conventional chip sampling, as evidenced by the reduced estimation errors achieved. The question of optimum sample spacing is discussed, and it is concluded that the required spacing for chip sampling needs to be smaller than for the diamond-saw method.

Jan 1, 1986

By W. T. Ruhmer

Slimes-dam construction in the gold mines of the Anglo American Group by w. T. RUHMER. Pr.Eng.. B.Sc. Eng. (Met.) (Fellow) Current practices generally in accordance with the principles of design and operation of slimes dams within the Gold Mining Division of the Anglo American Corporation are described. Although many of the details given are either obvious or have been amply dealt with elsewhere, these have been included for the sake of completeness. The selection of suitable ground for the deposition of slimes, the initial design and construction of a slimes dam, and its consequent operation are presented in logical sequence. Emphasis is placed on the code of practice for the construction of slimes dams issued by the Chamber of Mines of South Africa, and draft regulations (Water Act of 1956) dealing with pollution. Operating costs are included, and possible future trends are discussed.

Jan 2, 1974

By H. A. D. Kirsten

The professions are subject to a wide range of changing conditions, and are as a result forced to become more competitive. Although there is a need for specialization under these circumstances, no formal recognition, definition, or control of specialists exists. Some of the professions have attempted, over extensive periods of time, to resolve the issues involved, and have met with varying degrees of success. It appeared from the replies to a questionnaire sent to over one-hundred-and- .fifty professionals, that both advanced education and experiential training, are considered to be necessary qualifications for specialization. The opinion as to whether it should be lift to the individual to cal himself a specialist, or whether recognition should be based on peer review, was divided The majority did not want the number of specialists to be controlled The response to the reservation of work for specialists was ambivalent.

Jan 1, 1995

It is perhaps somewhat unusual for a contributor to comment on the authors' reply to his critique. However, I should like to return to a specific comment made by the authors. Award to Bob Laburn The Federation of Societies of Professional Engineers (FSPE) is pleased to announce that the 1984 FSPE Award for Services to the Engineering Profession was presented to Dr R. J. (Bob) Laburn at a function held on 14th February, 1984.

Jan 1, 1984

By R. C. O’Ferrall, W. G. Goulding

This paper describes the performance of a Robbins 52R Boxhole Borer from its introduction into the mine in July 1975 until late in 1977. As indicated by the costs involved, the performance has increased considerably and is expected to be even better once further envisaged modifications have been made. The average cost for the first half of 1977 was R275 per metre bored as against an average of R628 for 1975.

Jan 1, 1978

By B. P. Watson

The discussion written by Dr de Frey suggests that mine design should be based on closely spaced stability pillars. However, this concept leads to low extraction ratios at depth. The concept of `crush' pillars in conjunction with more widely, appropriately spaced stability pillars allows for significantly larger extraction ratios, particularly at depth. It should be noted that the rock conditions in many areas of South African platinum and gold mines are good, allowing significant spans to be mined safely between stability pillars. `Crush' pillars are cut small enough to fail stably near the face under stiff loading conditions, and their residual strength is intended to support about 10 m rock height between stability pillars. While this support resistance cannot be achieved by conventional support, crush pillars have been proven to have the required capacity for this purpose. The concept of leaving smaller crush pillars with appropriately positioned stability pillars has been used successfully for more than 30 years in areas of South African platinum and gold mines.

Jan 1, 2011

By F. S. A. de Frey, F. C. Kruger

Personnel management has undergone a remarkable change over the course of the past ten years. Personnel departments have played an increasingly important role, which today requires highly trained people and cannot be adequately served by the lesser qualified officials of yesteryear. Changes in the mining industry that stem from the demand for skilled labour to keep pace with technological developments and the mechanization of mines today demand that emphasis should be placed on the maximum utilization of manpower. Maximum utilization of manpower calls for more scientific and effective methods of recruiting, selecting, training, and placing workers so as to offer them the best opportunities for development and promotion, which naturally ensure a minimum labour turnover and eliminate labour unrest. This can be achieved only if well-qualified and properly trained personnel administrators are prepared to accept the challenge and apply themselves purposefully by assisting line mangement with the attainment of the company's corporate objectives.

Jan 1, 1982

By J. Kitagawa

The principal objectives of a metallurgical test programme for a 'grass roots' mining project are twofold. The first requirement is to establish the metallurgical viability of the project by demonstrating that acceptable results can be obtained by processing of the ore. The second goal is to obtain essential supporting data to determine whether the project is economically feasible. This involves several functions, which include the establishment of a workable flowsheet, the obtaining of design criteria for the commercial plant, and the collection of the evidence necessary to convince management, and often a third-party expert, that the metallurgy predicted for the ore can be achieved in a full-scale operation. The latter task is facilitated if a coherent overall picture is presented considering the geology of the orebody, the mining plan, and the mineralogy and metallurgy of the ore. The purpose of this paper is to provide guidance in the establishment of a test programme to meet the above objectives.

Jan 1, 1978

By G. Gafner

The paper gives the reasons for the development of a gold alloy of 990 fineness with good colour, durability, and mechanical properties, and explains why titanium was chosen as the alloying metal. Methods are described for the alloy?s production, solutionizing, and age-hardening. Mechanical properties are given as a function of deformation, age-hardening time, and temperature for three different starting states, and these properties are compared with those of some standard 14 and 18 ct jewelery alloys and pure gold. The effects of various salts and fluxes on the composition of the alloy after heat treatment at 1150, 800, and 500°C are discussed. These indicate how alloy scrap can be refined to pure gold, and how solutionizing and agehardening can be conducted without the use of vacuum equipment. The results of wear tests indicate that the alloy is more durable than normal coinage and jewelery alloys. Tips are given on the grain refining, soldering, and casting of the alloy.

Jan 1, 1989

By D. G. Krige

Some basic considerations in the application of geostatistics to the valuation of ore in South African gold mines by D. G. KRIGE, Pr. Eng., D.Se. (Eng.) Rand (Fellow) There is much room for improvement in the statistical procedures that have been used by gold mines over the past decade in the valuation of their ore reserves. Improvement depends on the establishment of the extent to which the patterns of frequency distributions and the directional variograms for the gold values vary from area to area within each section of a mine. The application of the lognormal distribution and of the De Wijsian variogram model for routine ore-reserve valuations requires detailed study before some of the reservations still held by mathematical statisticians can be met. This paper provides some preliminary evidence of the extent to which these models can be used with confidence, as well as suggesting how they can be applied to their full potential.

Jan 4, 1976

By R. W. O. Kersten

The South African Institute of Mining and Metallurgy recently held a School on iMine Project Planning, the objective being to educate mine personnel who are involved in the planning and management of major projects, as well as young engineers who may become involved in this field. Book prizes for universities Prizes are awarded annually by The South African Institute of Mining and Metallurgy for outstanding academic achievement by mining and metallurgical students at South African universities.

Jan 1, 1985

By J. N. Van der Merwe

It is shown that the safety factor as calculated traditionally by use of the tributary-area theory is not valid for high-extraction methods of coal mining. An alternative approach is suggested in which the pillar loads are calculated more realistically for the period during which pillar extraction is in progress. This safety factor, which is known as the Extraction Safety Factor (ESF), can be used in determining the effects of strong layers in the overburden on pillar sizes.

Jan 1, 1990

By M. G. Spengler

Mr More O'Ferrall must be complimented on a paper that will be a useful reference for the re-working of previously abandoned workings. His paper so closely mirrors experiences at East Rand Proprietary Mines, Limited, that it could well have been based on occurrences in that mine. Corrosion The Scientific Society of Mechanical Engineers is organizing the 115th event of the European Federation for Corrosion in Budapest, from 18th to 22nd October 1982.

Jan 1, 1981

By J. A. L. Napier, J. S. Kuijpers

SYNOPSIS This paper demonstrates that the horizontal stresses induced by the creation of a tabular scope in a single mining step are always tensile at the centre of the stope span, but that compressive stresses are actively generated in hangingwalls and footwalls during sequential mining. A stress-distribution mechanism is introduced, and is used to explain the results for elastic behaviour, and for inelastic behaviour both during a single mining step and during multiple mining steps.

Jan 1, 1991

By D. W. Horsfall

The coal-preparation techniques used in South Africa over the past ten years are reviewed, the term preparation being taken to refer to processes involving beneficiation techniques. The success of the preparation methods adopted can be gauged from the fact that, although South African coals are generally of a fairly low quality, the country is producing coals both that are used locally for the raising of steam and for metallurgical purposes, and that compete successfully on world export markets.

Jan 1, 1980

The Canadian Institute of Mining and Metallurgy. Milling practice in Canada. CIM Special Volume 16. 1978. The purpose of this volume is to up-date The Milling of Canadian Ores, which describes Canadian mineral. processing plants and gives other metallurgical information, and was published by the Sixth Commonwealth Mining and Metallurgical Congress in 1957. NIM reports Report no. 1874 Activation analysis and classification to soune of samples from the Kimberley Reef conglomerates. (10th Mar., 1977; released Jun. 1978). Report no. 1926 The analysis of anode sludges by X-ray-fluorescence spectrometry. (5th Jun., 1978). Report no. 1936 The analysis of mineralogical and metallurgical materials. A guide to the analytical techniques and instrumentation available at the National Institute for Metallurgy. Report no. 1959 The slag-metal equilibrium, and the activities of slag and metal components in the production of high-carbon ferromanganese. (15th May, 1978). Report no. 1965 Analyses, by several laboratories, of three ferromanganese slags. (22nd May, 1978). Report no. 1968 The influence of carbonaceous reducing agents on the rate of reduction of representative manganese and chromium ores. (28th May, 1978). Company Affiliates Guide To The Preparation Of Papers for Publication In The Journal Of The South African Institute Of Mining And Metallurgy The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal.

Jan 1, 1979

By G. A. Matthrsuis, R. N. Morris

The paper identifies two zones in a Leeds flotation cell. The ratio (13)of the dissipative forces and the interfacial tension force acting on a bubble and a solid particle are shown mathematically to be proportional to the square of the particle diameter for the quiescent zone and inversely proportional to the particle diameter for the turbulent zone. To locate the range of operation, correlations were established for the bubble diameter through photography and bubble counts. 13was found to be fairly constant in the particle size range 38 to 150 ",m, and the level of turbulence unlikely to affect the bubble-particle attachment and hence the beneficiation efficiency. This was verified in a series of flotation runs with a standard Leeds cell and a modified cell of twice the height to increase the capacity of the quiescent zone. A series of tests on the size range 300 to 600 ",m showed that the turbulence level had a marked effect on the cell performance through a relative improvement in the beneficiation efficiency due to the increased height of the cell. To identify the significant variables in the size range 38 to 150 ",m, a factorial design was carried out. Promoter dosage and particle size were found to be significant, aeration rate and impeler speed being insignificant at the 95 per cent confidence level. Multiple regression correlations were established for the recovery of organic material, mineral rejection, and beneficiation efficiency.

Jan 1, 1988