Search Documents

By E. J. Walls, W. C. Joughin

"In selecting a suitable method to sink a vertical shaft for underground access, a number of constraints influence the ultimate decision of where and how to develop the shaft, not least among these being safety, development and construction time, and cost. Two additional considerations stand out: these being geotechnical conditions and technology, the latter taking into account existing underground access. Assuming a project for which an existing underground excavation is available, it is tempting to build a shaft sinking project from the outset based on the raiseboring method, which has the potential to be the safest, fastest, and least expensive method provided that geotechnical conditions permit.And therein lies the rub: regardless of project time or cost constraints, when it comes to raiseboring a long (say, greater than 500 m), large diameter (greater than 4.5 m) shaft, the rock mass conditions ultimately dictate what method of shaft sinking will be feasible. Over the course of several studies for a particular project, several geotechnical analyses were carried out specifically for the purpose of developing a shaft by raiseboring. Risk analysis and experience showed that where the rock mass conditions indicated an unacceptably high risk potential, an alternative method needed to be considered, even if this meant increasing both the time and financial requirements.In this paper we present an overview of geotechnical investigation practices for shaft sinking. Decisionmaking thresholds for raiseboring or other methods of shaft sinking are discussed, including probabilities of failure, empirical rock mass classification, basic wedge failure, and back-analysis of a failed case. The design of appropriate support, and analysis of relative safety benefits for various shaft sinking methods, falls outside the scope of this work, and will be presented in a separate paper.IntroductionThe potential for rock mass failure during shaft development and construction affects whether a project is completed safely, on time and on budget. During the course of several studies to establish ventilation shafts for an underground expansion project, geotechnical analyses of rock mass stability and failure potential were carried out. The investigations were guided by the method of McCracken and Stacey (1989) together with insights from Peck and associates (Peck, 2000; Peck and Lee, 2007, 2008; Peck, Coombes, and Lee, 2011)."

Apr 1, 2019

By S. Ramatsoma, D. N. C. Phillpotts, B. Whitehead

Changes in flotation performance have been correlated to changes in froth structure, velocity and stability. Literature has shown that when the aeration rate is varied for a specific float cell, the recovery of the valuable mineral reaches a peak which also coincides with a peak in the air recovery – a measure of froth stability. Peak air recovery optimisation methodology is a way to use direct readings of physical phenomena by froth cameras to optimise the metallurgical performance of a flotation plant. The aim of this paper is to show the transient nature of the peak air recovery value and the variety of conditions required to attain the peak air recovery on an industrial flotation plant with tight base-layer control of the feed and internal conditions. Industrial site tests that were conducted under controlled conditions showed different peak values at significantly different corresponding aeration rates during normal operation. The measured peak air recovery points corresponded to maximum PGM recovery during normal flotation, as expected. This dynamic nature of the peak air recovery point conditions has not previously been discussed in literature and indicates the need for online measuring equipment and informs the design of process control algorithms required to exploit the phenomenon for optimisation. Keywords: Froth flotation, flotation control, flotation optimisation, peak air recovery

Jan 1, 2020

By C. Mueller

Automation of mining operations is pushed by cost pressure and cyclical product prices. However, until now the different types of equipment were not able to communicate electronically with each other or with central computer systems. Therefore, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ‘common electronic language’ for easy and standardized data exchange. As in other industries, this standard is expected to have significant impact on the use of automation in general and on the markets for third party components and software. The standard’s technical architecture is open and flexible for future applications. It consists of an ‘horizontal’ structure defining ‘Application Profiles’ for different types of data sets. An additional ‘vertical’ structure (‘Equipment Profiles’) implements equipment dependent definitions for each of the applicable Application Profiles. First profiles will be available for Drill Rigs. The standard bases on the XML language thus enabling easy data exchange with commercial databases. IREDES data sets may use storage media as well as networking infrastructures for information exchange. The IREDES work is carried out by the initiative members working jointly together in the IREDES work groups. It is open for participation of all interested organizations. First prototyping applications are expected to start during 2001, the first products may be available in the following year. Key words: Mine Automation; Machine Automation; Data Exchange; Rock Excavation; Standard; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Service; Quality Assurance; Control Centre;

Sep 1, 2001

By L. A. Vermeulen, D. D. Howat

New distribution functions are derived to describe the size distribution of grinding elements in ball mils. The formulations are based on the assumption that abrasive as well as impactive interactions occur during bal milling-an assumption that is supported by a large body of experimental evidence. It is shown that the functions can be used in the estimation of the magnitudes of abrasive and impactive components in the total rate of bal wear. The relative magnitudes of the wear components provide a basis for optimization of the chemical and metallurgical properties of the balls in a given milling situation. However, it is contended that these quantities are also useful indicators of the relative intensities of the abrasive and impactive interactions that are operative in the size reduction of mineral particles within ball mils. These quantities can be determined for any industrial ball mil, and their magnitudes provide practical guidelines for mil operation. The theory is used in an analysis of samples of ball charges from two industrial ball mils, and it is also applied to al the data on bal-size distributions found in the literature. The qualitative correlation between the calculated values of the wear components and the reported operating conditions is good for a variety of industrial ball mils, in conformity with the hypothesis that the relative magnitudes of the wear components are related to the milling conditions.

Jan 1, 1986

By Nelson Sánchez

The Los Bronces Development Project (LBDP) was approved in October 2007 by the Anglo American plc Board at a capital cost of some US$1.74B, and is scheduled to be completed by the end of 2010. The project represents a big step forward for the Los Bronces mine since it will increase the treatment rate by 140%, the mining rate by 64% and almost double copper production during the first four years of the project. This economy of scale will also position Los Bronces as a much bigger and efficient mining operation, better prepared to face adverse market scenarios and allowing Anglo to consolidate its position in base metals. The project addressed numerous scope alternatives such as plant capacity vs mine capacity, cut-off grade strategy to maximise value based on the existing flotation and leaching process, cutback strategy, etc. Main infrastructure aspects of the project are as follows: ?Dump area with 2400Mt capacity for waste and low grade material ?Mining equipment: 1 x electric shovel, 12 x 300t trucks, 1 x drill ?Primary crusher: 60? x 89? ?Three new power lines (144MW capacity) ?Grinding plant at 87kt/day nominal capacity (includes a 4.3km tunnel with a regenerative conveyor belt) ?Grinding plant: 1 SAG mill 40? x 25?, 2 ball mills ?Slurry pipeline (52 km from grinding to flotation plant) with five choke stations ?Flotation plant (rougher, cleaning, regrinding circuits and molybdenum flotation). The history of Los Bronces started in 1867 when it was discovered. In 1978 ENAMI (Government company) sold Los Bronces to Exxon for US$112M. The same year a snow avalanche destroyed San Francisco Flotation Plant. In 1979 the plant was rebuilt at 4.9kt/day and from 1979 to 2002 several plant expansions were made up to 54kt/day capacity. In 2002 Anglo acquired Los Bronces for US$1.3B. The 2002 resource and reserve statement showed reserves at 459Mt at 1.02%CuT and resources at 780Mt at 0.80%CuT. The 2007 statement shows reserves at 1,480Mt at 0.67%CuT and resources at 1,644Mt at 0.45%CuT. Defining the size of a plant expansion is the key challenge that any expansionary project faces. The scope of this paper is a general review of the project, describing all the mining techniques that were used to define the best options that maximise value. In this context, a range of plant capacities (from 58 to 230kt/day) combined with a range of mining capacities (from 83 to 166Mt/a) were evaluated in detail, defining for each option a mine plan, Capex and Opex, and cut-off grade strategy for flotation and leaching processes and the associated Net Present Value (NPV) that was used as the selection criteria. The Los Bronces mineral resources potential provides good growth opportunities for the mine beyond LBDP implementation, offering an exciting invitation to continue studying new initiatives that maximise the value of this deposit.

Jan 1, 2008

By J. W. Neale

Mintek was a leading participant in the BioMinE project between 2004 and 2008. This project, which was funded in part by the European Commission, was aimed at the development of biotechnology for the minerals industry in Europe. Mintek?s research programme focused mainly on the development of integrated bioleach-based processes for the recovery of base metals from complex, low-grade sulphide concentrates. Specific European mineral resources were targeted and used in integrated piloting campaigns involving bioleaching, solution purification, and metals recovery. This paper describes the use of thermophilic bioleaching for the recovery of nickel and copper from a low-grade nickel-copper concentrate produced at the Aguablanca Mine in southern Spain. Currently, the Aguablanca Mine produces a bulk nickel-copper concentrate for sale to a smelter, and the proposition is to increase the profitability of the operation by the on-site production of metal or metal intermediate. Initially, bench-scale bioleach tests were conducted to determine the bioleach operating conditions. These tests included an evaluation of mesophilic, moderately thermophilic and thermophilic microorganisms. In order to achieve sufficiently high levels of both copper and nickel extraction, a thermophilic process was selected?this was necessary for leaching of the refractory chalcopyrite that occurs in this concentrate. Additional bench-scale test work was carried out to derive a conceptual process flowsheet for the solution purification and metals recovery circuit. The results of the bench-scale tests were used to design, construct and commission an integrated pilot plant, which was subsequently operated at Mintek for over seven months. During this time, the solution purification and metals recovery processes were optimized, and all recycle loops were closed. The final process flowsheet included the following unit operations: concentrate regrinding, thermophilic bioleaching at 70°C, primary iron removal using limestone, copper solvent extraction and electrowinning, secondary iron removal, nickel hydroxide precipitation using magnesia, and final solution purification using lime. Where applicable, process solutions were recycled to preserve water. The process design data derived from this pilot-plant campaign formed the basis for a conceptual engineering study for the developed process. In the study, mass and energy balances were derived, and a process flowsheet was developed and used as the basis for estimating the capital and operating costs of the process. This enabled a preliminary economic analysis of the process to be undertaken. The findings of this study are discussed.

Jan 1, 2009

By E. Bakhtavar, R. Mikaeil, D. Khademi

"Fuzzy-weighted integer goal programming has been developed and used to select the most suitable site to construct a central processing plant for several adjacent small-scale dimension stone quarries, based on the most effective criteria. In the first step of mathematical modelling, the most important goals and decision variables were defined. Accordingly, an objective function was used in the model for minimizing the sum of undesired fuzzy-weighted deviations. Fuzzy weights were determined by a matrix of pairwise comparisons of various expert judgments in this field and the fuzzy geometric mean. The goal and systemic constraints were also modelled. The most suitable site for the construction of the plant was selected after solving the mathematical model in the ExcelR Solver add-in. The selected site had various advantages over the other sites, such as the shortest average distance to the quarries, the shortest distance to power access and workforce, and the lowest land price. IntroductionSelection of the most suitable site of a plant is one of the most important considerations when constructing an industrial project. A suitable site has a significant effect on a company's competitiveness in the market. Selecting a desirable location for constructing plants such as mineral processing facilities is an essential part of the economic planning that will enable a company to meet the needs of related upstream and downstream operations. These units are considered to be best built near the relevant mining sites because of technical difficulties, the cost of transporting minerals, and the traffic hazard caused by the movement of trucks transporting materials. Two main types of research using multiattribute decision-making models have been reported for selection of a processing plant site (Safari et al. 2010, 2012). In that research, the analytic hierarchy process (AHP) and fuzzy technique for order preference by similarity to ideal solution (TOPSIS) approach were applied to select the suitable locations for the mineral processing plants for phases 1 and 2 of Sangan iron ore mine."

Jan 1, 2017

It is suggested that an increase in the production from thin coal seams in South Africa is necessary, and that a substantial amount of any increase will be mined by the bord-and-pillar method. For the purpose of this study, a thin coal seam was regarded as any seam 1,5 m thick or less to the minimum thickness at which mechanized equipment can operate in bord-and-pillar workings. The equipment being utilized in thin-seam bord-and-pillar layouts includes conventional equipment, load-hauldump cars (scoops), and drum-type and Fairchild-Wilcox continuous miners. Comparisons are made of these types of equipment for bord-and-pillar mining at various seam thicknesses within the thin-seam range. The evaluations involved production rates and the cost of extraction for South African conditions, use being made of an existing computer modelling technique in the generation of production rates. The indications are that, for seam thicknesses greater than 0,9 m, drum-type continuous miners utilizing continuous haulage are the most productive and cost-effective equipment at present operating in thin-seam bord-and- pillar workings. Where seams thinner than 0,9 m are to be exploited, Fairchild-Wilcox continuous miners, particularly the Mark 22, produce the most coal at the lowest cost.

Jan 1, 1984

By H. J. R. Way

Dr H. J. R. Way: In his reply to my queries Mr Bath still adheres to his statement that it may be possible to replace the estimated R200 million reduction in gold revenue in 1980 by exports of ferro-chromium, and apparently based his conclusion on a growth rate in demand for corrosion resistant steels of 10 per cent per annum in the next few years. As I pointed out at the previous discussion at Middelburg this would entail a production of about one million tons of ferro-chromium in 1980. Exact statistics of South African ferro-chromium production are not available, a fact which is very much to be regretted. But statistics of exports of ferro-chromium are available from "Foreign Trade Statistics" of the Customs and Excise. These show that South Africa exported 99,580 short tons in 1967. The quantity of ferro-chromium consumed in South Africa in 1967 was fairly small and we can therefore assume that the production was 99,580 tons. For this amount to grow to 1,000,000 tons in 1980 would require a growth rate of 19.4 per cent per annum. At 10 per cent this would grow to 344,000 tons and at 7 per cent 240,000 tons. The following growth rates in the form of average trends are pertinent: STEEL - Per annum World steel ingot production - 1957-67 – 6.8 per cent Free-world ingot production - 1957-67 – 6.0 per cent Consumptions of crude steel by four major Free-world Consumers - 1957-67 - 5.6 per cent CHROMITE World production - 1952-67 - 2.5 per cent South African total sales - 1948-67 – 5.4 per cent South African exports - 1948-67 – 3.9 per cent United States consumption, very irregular, but - 1962-67 – 6.5 per cent FERRO-CHROMIUM - Per annum United States consumption - 1952-67 - 6.5 per cent South African exports - 1957-62 - 25.2 per cent South African exports - 1962-66 - 41.9 per cent South African exports - 1966-68 - 21.2 per cent These figures show that exports of ferro-chromium have been growing at a very high rate varying from 21.2 per cent to 41.9 per cent since 1957, but in view of the market situation it seems somewhat doubtful if that high rate can be maintained up to 1980. Of our 1966 exports U.S.A. took 63 per cent which was 53 per cent of their total imports. Their average consumption is trending at a growth rate of 6.5 per cent per annum from 1952-67, but the growth from 1964-66 was 5- 2 per cent and 1966-67, -12 per cent!

Mar 1, 1968

By J. P. Hoffman

In 1988 the Japan Iron and Steel Federation started a research-and-development programme known as DIOS (direct iron-ore smelting). Eight Japanese integrated steel producers and the Coal Mining Research Centre, subsidized by the Ministry of International Trade and Industry, are involved in the project. The aim of the programme is to have a 500 v/d pilot plant for the production of iron via an oxygen-coal in-bath smelting converter in operation by mid 1993. The three main components of the DIOS process are as follows: ?a fluidized bed for the pre-reduction of iron-ore fumes ?in-bath smelting reduction in a converter ?off-gas reforming by the addition of coal fines. The main drive is to provide a smelting process that is more energy-effective, using coal instead of coke and/or electricity. The advantages claimed include inter alia ?direct use of fine iron ore ?direct use of non-coking coals-low coal consumption ?low capital expenditure-replaces costly coke ovens, agglomeration plants, and the blast furnace ?economical production on mini-plant scale ?less of an impact on the environment. This concept of 'direct steel has been carried over to the production of stainless steel direct from the ores, again bypassing such energy-intensive units as the submerged-arc furnace for the production of ferrochromium. A number of Japanese companies have indicated a certain amount of success. Several interacting elements are recognized that could have a productivity-limiting aspect. The possibility of the direct production of stainless steel from chromite is discussed briefly with reference to the Highveld of the eastern Transvaal as a possible site for such a plant

Jan 1, 1992

By H. Rosenberg

Haldor Topsoe A/S has developed its WSA technology to meet the demand in the market for a simple and reliable process that converts sulphurous emissions from off-gasses into high-grade sulphuric acid. With more than 50 references in 25 countries, the WSA technology has proven its ability to generate acid at 98% concentration, efficiently and economically. The wet gas sulphuric acid (WSA) technology treats the furnace off-gas directly from upstream gas cleaning plants. No further drying is required, since the humidity present in the off-gas is used to hydrate the SO3generated in the converter and produce sulphuric acid. The heat generated during the oxidation, hydration and condensation processes is principally reused in the process to preheat the off-gas to the required temperature level, and also to generate high pressure superheated steam for process use. This advantage of steam production, coupled with lower water and power consumption requirements, is particularly important in the African production environment. Having fewer process components than conventional acid plants, the WSA technology is a simple and compact operation, which makes it easier to retrofit into an existing smelter plant. Further, the WSA technology simultaneously offers the possibility to treat multiple gas streams arising within the production facility due to superior flexibility in terms of SO2concentration and turndown ratio.

Jan 1, 2006

By D. Fourie

A brief history of channel sampling in South African gold mines is followed by a chronicle of different sampling events and sampling methods that used the traditional ?hammer and chisel? approach as well as diamond core extraction of the sample. The problems associated with each method of sample collection are documented and the use of a laser scanner to measure the exact volumes of sample material extracted from a correctly delimited sample site are considered. Areas where increment delimitation errors (IDEs), increment extraction errors (IEEs), increment weighting errors (IWEs), and increment preparation errors (IPEs) occur were investigated. A ?simulated chip sample model? is introduced and provides the basis for comparing the percentages of error introduced as a result of improper sampling. The heterogeneity experiment showed that reefs that are more homogenous tend have lower extraction errors than the more complex carbon-rich reefs, which may contribute to understanding the poor mine call factor on mines exploiting the latter types of reef. Keywords channel sampling, chip sampling, error, bias, modelling.

Jan 1, 2014

By B. Genc

Improving student success rates without compromising the quality of graduates is one of the biggest challenges expanding university programmes are facing in South Africa. By establishing a new Mine Design Laboratory (MDL) for higher learning in Mining Engineering, the School of Mining Engineering at the University of the Witwatersrand (Wits Mining) has achieved one of the important goals in its five-year strategic plan, i.e. to improve throughput in all years of study. Although the establishment of the laboratory has been a costly exercise, results so far have shown an improved success rate in most subjects taught in the facility. This paper outlines the design and equipment of the laboratory, the facilities incorporated, a comparison with the old laboratory, and the performance of students?all of which indicate how important it is to have proper facilities to improve the teaching of, and learning by, large classes. Through this initiative, Wits Mining has taken an important step that will contribute to addressing the skills shortages in the mining industry.

Jan 1, 2012

By M. Berjak, D. M. Hawlins, R. B. MacGillivray

SYNOPSIS The paper describes a method of producing iso line plans using a mathematical technique for interpolating between boreholes, and its computer application. The iso line plans are used for assessing the value parameters of an ore body. The computer programme also produces means and standard deviations to supplement these iso line plans. The mathematical techniques tested for the production of a satisfactory fit of the data were the polynomial, Fourier and moving average technique. The iso line plans are used for assessing the quality of the ore and other salient features such as depth to the floor of the ore body at different points, with a view to deciding how best the ore may be mined. The plans are plotted by the computer to any scale required. INTRODUCTION To assess the economic exploitability of an ore body many tedious and repetitive calculations must be carried out. Observations of borehole or development samples have to be processed yielding measures of ore reserve and quality in each sampled area, and also measures of the worth of the ore body as a whole and of variation in quality from section to section of the ore body. The observations made on the ore (which we shall term 'value parameters') may embrace a variety of characteristics of the ore. Obvious value parameters are those directly related to the economics of mining, viz. assay values, ore body thickness and depth below surface. Other value parameters however may be almost as important. In the case of coal for example a purchasing contract may specify limits of acceptability on other value parameters such as calorific value, ash content or the percentage of volatile matter. In this case, a detailed study of these value parameters will also be crucial. This detailed study must include an assessment, not only of the body as a whole, but also the regional variation in value of the parameter. An obvious and satisfactory way of displaying this variation is by drawing iso lines of constant value parameter on a map of the ore body and supplementing this with the means and standard deviations of the value parameters taken over all boreholes. Such plans, considered together, show up the zones of significance. The relatively stereotyped nature of the operations involved in this process makes it amenable to computer solution. In order to produce iso line plans on the computer we require some mathematical formula for producing a 'valuation surface'-a mathematical

By J. A. C. Diering

The determination of stresses and displacements close to tabular excavations is of considerable importance in the planning of tunnels and of remnant and pillar layouts. This paper gives a description of a simple yet effective method for the achievement of improved values from an analogue or MINSIM type of analysis. Essentially, closures and rides (the movement of hanging-wall relative to footwall) in mined-out areas are assumed to vary in a piecewise linear fashion as opposed to a piecewise constant fashion. As the former fashion more closely resembles the true variation, it is possible for the stresses and displacements at points close to the excavations to be calculated with much better accuracy.

Jan 1, 1980

By F. Ma, F. Yang, T. Zhao, P. Dai, Z. Shao, D. Zuo

With the development of modern digital technique, computers have been widely used to monitor and control in retrofitting traditional industries. In Chinese coal industry, some analog monitoring and control systems have been replaced by the modern computer digital systems. According to the development status of Chinese coal industry, this paper presents some technique and its applications of modern digital computer monitoring and control for safety mining production process. The technique has been used in the full digital monitoring and automation control for hoists, coal mining machines, belt transport machines, and whole coal mining production process. With the technique, it has been achieved the better economical and social benefits in safety mining production in China.

Jan 1, 2003

By V. M. Lovell, N. P. Finkelstein

The concepts involved in flotation research are discussed and aims are presented. Three different method. of investigation can be used, all of which are applied at the National Institute for Metallurgy (N.I.M.), and these are the empirical, trial and error method, the chemical engineering method, and the physicochemical approachs This paper is devoted to the last of these. Because of the complexity of the physicochemical interactions involved, the work has, to a large extent, been concentrated on only one aspect, viz. the interaction between the mineral surface and reagents in solution, which was considered of major importance in the understanding of the process. The aspects on which work has been done are the concentration of uranium, the reaction between salt minerals and fatty acids, mixed xanthate-cationic collector systems, and the reaction between sulphide minerals and thiol reagents. Selected problems from the first two of these are discussed in some detail and deal with the agglomeration flotation of uranium and the chemical control of the flotation process for phoscorite. A detailed discussion is also presented of the progress made in the understanding of the interaction between sulphide minerals and thiol reagents, which is of more general application. Finally, an indication is given of the future direction of physicochemical research at the N.I.M.

By K. Böde

Hochtief AG Germany has developed a comprehensive management and information system for the construction industry named Aristoteles. This system is an efficient supporting tool to manage a variety of construction sites as well as operating business units with required economic targets. As such, Aristoteles offers wide-ranging control of complex economic processes in construction in a consistent manner. In this paper the process oriented functions of the system will be described with special emphasis on finance accounting and cost control. The basic elements in this respect are tender estimation, creation of initial project budgets and running budgets, regular determination of work done and result forecast to the end of the project. Further, cost accounting, monthly reporting, and all balance-related postings are included. On the basis of the extensive reporting (targeted/actual cost comparison, cost manager, project report, actual/targeted hours worked comparison, overhead cost report, amendment report or project (result) lists of all projects realized by one business unit), the responsible managers can make justified project evaluations, project controls and variance analyses during the project period and derive appropriate management measures. Thus, Aristoteles includes all substantial elements for the risk management of the operational business. In big construction joint-stock companies it is of crucial importance to satisfy the information requirements of the investors. In this respect the system provides a transparent presentation of the financial, investment and profitability situation of the company. In the international construction industry the balancing rules according to IAS (International Accounting Standards) have already been used to a larger extent. In accordance with these rules the partial profits of the work during execution can be shown as realized even before completion of a long-term contract. The validity of Aristoteles will be outlined briefly. Major advantages using the system are highly enhanced accuracy of project controlling, systematic overhead allocation to projects, change of attitude of the project personnel due to increased cost consciousness and improved flow of information within the company.

Jan 1, 2003

By W. C. Joughin

A risk evaluation model has been developed, that enables the quantification of expected injuries and economic losses resulting from rockfalls associated with a support system in a given geotechnical environment. This enables the comparison of different support systems based on the expected frequency of injuries and the total cost of the support system, including the expected economic losses. The model takes into consideration the variability in joint orientations and joint strength within the geotechnical environment and the variability and quality of support systems. The quantification of the benefits of other rockfall risk-mitigating strategies, such as the effectiveness of barring or monitoring, are also incorporated in the model. The risk model is described in this paper and the validation of the model and case studies are described in Part II.

Jan 1, 2012

By Z Bagheri, E Moosavi

Identifying the exact borders of geological domains and assessing the uncertainty of these borders are crucial steps in resource estimation. This potential field method was designed to build 3D geological models from data available in geology and mineral exploration, namely the geological map and a digital terrain model, structural data, borehole data, and the geologist’s interpretations. The resource evaluation of a copper ore deposit is often performed in three steps: (i) delimitation of the boundaries of the units corresponding to the various geological formations or ore types; (ii) estimating densities; and (iii) estimation of grades within each unit. In simple cases (e.g., a series of sub-horizontal layers), the geometric model can be built using 2D geostatistical techniques (kriging or co-kriging of the elevations or thicknesses of the various horizons) which also quantify the uncertainty of the model. A 3D model of Cu grade is generated using ordinary kriging; however, the indicator kriging method is run to design a 3D model of rock types by incorporating the drilling results. Block models of geophysical and geological characteristics are included in a similar 3D mesh to investigate their relationships in copper mineralisation.

Sep 1, 2021