Search Documents

By Mary F. Koehler

Interoxidic compounds, such as vanadates, have not been studied extensively in the field of thermodynamics. This is a report of three vanadates of sodium--metavanadate, pyrovanadate, and orthovanadate. Vanadates of other metals will be considered in future reports. The heats of formation at 298.15° K. of the three sodium vanadates (both from the oxides and from the elements) were derived from the results of sodium hydroxide solution calorimetry. Free energies of formation were obtained by combining heat and entropy values. The results support the conclusion that the three sodium vanadates were stable with respect to all possible decompositions in which vanadium retains its pentavalency.

Jan 1, 1960

By Jr. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel.

Jan 1, 1931

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) spin trapping methodology has been used to study the reactions of manganese dusts with glutathione, employing a-{4-pyridyl-1-oxide)·N-tert-butyl-nitrone (PBN) and 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) as spin traps. The results show evidence for the glutathionyl radical formation in the reactions of both MnO2 and manganese (Ill) acetate with glutathione. Based on these experimental observations, we hypothesise that the mechanism of neurotoxic effects of manganese might be due to the fact that the generation of glutathionyl radicals depletes the glutathione pool and reduces the glutathione shield against free radical products of dopamine metabolism and manganese induced reactive oxygenated species. IntroductionExposure to manganese compounds often occurs as the result of foundries and mining operations (1. 2). Other significant sources of environmental manganese include coal-fired power plants and burning of residual and crude oil (3, 4). Lately gasoline combustion has also started to contribute since manganese (methyl cyclopentadienyl manganese tricarbonyl. 0. 125 g/gallon) is being used instead of lead as an antiknock ingredient in automobile fuels (5. 6). Although manganese is an essential element in certain biological processes it is toxic in excessive amounts. The manganese toxicity is mainly associated with the nervous system (7-9). Symptoms frequently observed in manganese poisoning or manganism are disorientation, memory loss, anxiety, compulsive laughing and crying, mask-like faces, akincsia rigidity and tremor (10). In spite of numerous investigations to understand the mechanism of manganese induced injury. it has not been possible to localize the initial chemical lesion responsible for altered physiology and ultimate cell death. This may perhaps he the reason for failure in developing a successful therapy for manganese intoxication."

Jan 1, 1990

By C. H. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is al¬ways the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxida¬tion practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel.

Jan 1, 1931

By G. R. Hopkins

[ ]

Jan 1, 1927

By B. J. Dalton

Several relationships between coexisting phases for analytical binary solutions near the critical point are given. These relationships were developed from a consideration of a (G u, P) surface at constant temperature and a (G u, T) surface at constant pressure, where G is the molal Gibbs free energy, u is the concentration of component 1 expressed as a mole fraction, G is the pressure, and T is the temperature. These formulas should facilitate the calculation of some of the quantities useful in making thermodynamic consistency checks on phase equilibria data about the critical point.

Jan 1, 1970

By Laxman S. Sundae

In the vast majority of American coal mines, roof bolt holes are drilled dry, mainly because of mine operator concern with the spent water creating adverse working conditions. Wet drilling, however, can increase drilling rates and the effective lifetime of the drill bits used. This study, carried out as part of an ongoing cooperative research program between the U.S. Bureau of Mines and the University of Missouri-Rolla, shows that the large volumes of water conventionally used in wet drilling are not necessary, and the performance benefits from wet drilling can be achieved with total volume flows on the order of 0.4 L per hole. This conclusion is validated based on the measured respirable dust generated in drilling Berea sandstone. The results are confirmed using a variety of bit shapes, which are also shown to have a significant effect on penetration rate.

Jan 1, 2010

By G. W. Birge

Twenty-eight samples, representing the Pittsburgh, Lower Kittanning, Stockton-Lewiston, Coalburg, Winifrede, Cedar Grove, Peerless, No. 2 Gas, Powellton, and Eagle beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expanding characteristics of 22 of the samples were determined in the Bureau of Mines sole-heated oven. The Kanawha County coals tested were high-volatile A bituminous in rank, with dry, mineral-matter- free fixed- carbon contents ranging from 53.9 to 66.3 percent. With few exceptions, they were chemically satisfactory for metallurgical use, and most of the coke-strength indexes were within the industrially accepted range for high-volatile blending coals.

Jan 1, 1963

By John A. Johnson

[Tests were conducted at the Mount Weather testing adit of the Bureau of Mines4/ on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. EQUIPMENT Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is made of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.]

Jan 1, 1939

By George H. Holmes

This paper , which describes mining methods and milling and manufacturing operations at the gypsum property of the Blue Diamond Corp. , is one of a series on mining methods and practices being prepared by the Mining Division of the Bureau of Mines . The property comprises about 4,000 acres and is in secs . 30 , 31 , 32 , and 33 , T. 21 S. , R. 59 E. , and secs . 5 , 6, 7 , 8 , and 9 , T. 22 S. , R. 59 E. , M. D. B. and M. , Clark County , Nev . , approximately 23 miles by paved highway southwest of Las Vegas , Nev . ( fig . 1 ) . This circular summarizes the history of company operations , describes physical features , labor and living conditions , and the geology . The method of exploration is outlined , and the section on mining methods contains descriptions of open - pit and underground systems , including loading and transportation methods . The crushing plant and tramway are described , as well as plaster-mill and board -plant practices . The boiler plant and organization are described , and wage scales are contained in the concluding section of the circular .

Mar 1, 1950

By G. Richards Gwinn

"Mica" is a group name for a number of orthosilicates of aluminum with magnesium, ferrous iron, and the alkalies. They are characterized by their high reflection and a basal cleavage so well developed that they can be split into exceedingly thin laminae, which are more or less tough, elastic, and transparent, according to variety. Barium, manganese, lithium, chromium, titanium, boron, and ferric iron occur in same varieties. Eight distinct species of true mica, which appear in the following table, are recognized by mineralogists, but only the first five are of commercial importance. [Species General Formula Muscovite H2KA13 (SiO4)3 Phlogopite [H,K, (MgF)]) Mg3A1 (Si04)3 Biotite (H,K)2(Mg,Fe)2(Al)Fe)2 (S104)3 Lepidolite K,Li Al(OH,F)2 Al (5103)3 Ros coalite H8K(Mg,Fe) (A1,V)4 (S103)12 Paragonite H2NaAl3(S104)3 Zinnwaldite (K)Li)3 FeAl3 Si5016(OH,F)2 Lepidomelene HK2F3IIIFe6III A13 (S104)9]

Jan 1, 1951

By A. Viksne

A series of tests were conducted by the Bureau of Mines to determine the best means of reducing noise generated by the detonating cord that is utilized for trunklines in quarry blasting. Ten different types of detonating cord were tested and evaluated for their acoustic qualities. The results of the investigation showed that noise levels produced by "low-core-load-per-foot" detonating cord "not covered" were lower than those produced by "high-core-load-per-foot" detonating cord covered with 6 inches of unconsolidated material.

Jan 1, 1972

By E. C. Lane

During the past 15 years the Bureau of Mines has made and published several hundred analyses of typical petroleums and has developed a system of interpreting the analyses and of classifying crude oils. In describing crude petroleum frequent reference is made to the "base" of the oil, a usage the petroleum industry has found convenient. As part of its general study of the characteristics of crude oils, therefore, the Bureau of Mines has developed a system of classifying them according to "base." This system as first published in 19274 was limited to four classes and in its original form is no longer considered adequate. Since the system was first published the Bureau has analyzed a large number of crude oil-, including representative samples from nearly every important producing field in the world, and has found that the system of classification could be revised and amplified to advantage. The revised system is presented herein. Bulletin 2916 states that many oil producers and refiners use the word "base" much as it is used in pharmaceutical work. For example, the "base" or "basis" of an ointment or salve is the fatty material (lard, petroleum, or lanolin) used as a vehicle or carrier for the active medicinal principles. Apparently many of the pioneers in the petroleum industry considered crude oil similar in nature to these medicinal products in that it consists of a semisolid, nonvolatile base and 1 volatile portion can be distilled off to make gasoline, kerosene, and other products. Many crude oils when chilled slowly deposit a waxy material (paraffin); this fact may have been one reason for the use of the term "paraffin base" in referring to such oils. Almost all of the petroleum first discovered in the United States was of this nature; not until the oil industry was extended to California and along the Gulf coast was petroleum found that contained no wax but apparently did contain asphaltic material Accordingly, these oils were known as "asphalt-base" oils. The use of this term, however, seems unfortunate, as better-grade oils of this type contain little if any asphalt; the descriptive term "naphthene base" now seems to be a more desirable term than "asphalt base." The term "intermediate base" is also used commonly in referring to oils intermediate in oharacteristios between those of paraffin and naphthene base.

Jan 1, 1935

By Robert F. Holub

The U.S. Bureau of Mines (USBM) has tested a personal dosimeter for measuring radon decay products that is manufactured by Tom Scurry Associates. The tests were made to determine the accuracy of the dosimeter system for record keeping of radiation exposures to radon decay products encountered in mining. The radioactivity-detecting head is based on a design developed by the USBM, and the associated air pump was developed by the manufacturer. The dosimeter system was tested in the USBM radon chamber. The detecting head uses CaF:Dy thermoluminescent phosphors and is mounted on a self-regulating air pump. Batteries supply power sufficient for an 8-h shift. The dosimeter system is worn on the miner's belt. Dosimeter calibration tests were performed by the USBM. In addition, the pumps were tested and evaluated under continuous flow conditions. The results of these tests indicate that the Tom Scurry Associates Model DOSI600 dosimeter is suitable for general use in mines where record keeping for natural radiation exposure is required.

Jan 1, 1995

By Wm. W. Odell

For a number of years there has been a very appreciable annual,, increase in the production and recovery of natural gas and natural-gas gasoline2 in the United States the latter product being used largely for blending with gasoline from petroleum in the production of motor fuel. On account of the increased amount of oil cracking in the production of gasoline and the accompanying increased percentage of low-boiling constituents in the resulting product, the specifications for the natural gasoline suitable for blending have been altered, that is, the amounts of propane and butane which it can contain have been limited. The result has been that large quantities of the latter materials are wasted because there has been no ready market for thorn in large quantities. Because of this wasteage and because it is probable that large quantities of there and similar materials will be produced in the near future us a result of the more general use of oil cracking processes, a study was made by the Bureau of Mines, under a cooperative agreement with the assistance of the Phillips Petroleum Company, of the suitability of these materials alone or in mixtures for use as gas enricher in the carburetion of water gas for city distribution. This investigation included: (a) A study of the properties of the low boiling members of the paraffin series including pentane with particular reference to their utilization as gases.

Jan 1, 1927

By Gwendolyn D. Hood

The U.S. Bureau of Mines developed a dewatering technique for treating wastewater that was tested on waste slurry from a commercial tile company in Alabama. Raw wastewater samples were pretreated with 10 Ib calcium chloride and 10 lb Wyoming bentonite per 1,000 gal of slurry. After pretreatment, polyethylene oxide (PEO) at dosages varying from 0.05 to 0.20 lb per 1,000 gal was mixed with the waste slurry, forming strong, tough floes that were separated from the clarified water using a trammel. The flocculated slurry was dewatered to a consistency that could be handled for subsequent disposal in a landfill. The clarified water quality was equivalent to that of the company's present treatment system.

Jan 1, 2010

By A. J. Barry

An apparatus and procedure have been developed for testing the anchorage effectiveness of slotted-type bolts. The apparatus consists of: (1) A hydrualic Jack assembly for loading the bolt and (2) a device (extensometer or cathetometer) for measuring displacement of the bolt as it is loaded. This apparatus and procedure permit measurment of anchor slip for loads up to the yield load of the bolt. Two representative makes of slotted-type bolts (a total of 94 bolts) were tested in typical sandstone and shale mine roof. Analysis of the test results showed that (1) anchorage capacities up to the yield load of the bolts can be developed in either rock type; (2) the shape of the slotted end of the bolt affects the ease with which the bolt can be driven; (3) all bolts for which the driving distance was more than 1.25 inches produced satisfactory anchorage in both rock types (thus, driving distance can be used as a criterion for satisfactory anchorage); (4) for the group of bolts that was satisfactorily anchored the anchor slip was unaffected by the type of bolt but was considerably larger in shale than in sandstone; and (5) the bolt expansion, that is, the amount the wedge expands the prongs in excess of the diameter of the hole, can also be employed as a criterion for satisfactory anchorage. Although the bolt-expansion and driving-distance results do not differ appreciably, the latter is recommended because it is easier to determine.

Jan 1, 1954

By Jun Yi

In this paper, single-component gas sorption and transient diffusion processes are described within coal matrix exhibiting bimodal pore structure. The coal matrix is treated as a poroelastic medium manifesting swelling and shrinkage effects due to the sorption of gas under effective overburden stress. Gas transport is considered Fickian with molecular (bulk) and surface diffusion processes simultaneously taking place in the macro-and micropores of coal, respectively. The numerical formulation is intended to be explicit in nature to investigate the influences of sorption phenomena on the macropore volumes and on the overall gas transport for the cases of gas uptake by and release from coal. Results of the study show the presence of hysteresis during a sorption?desorption cycle of the gas. It is also found that the overall gas transport takes place at a rate significantly less than that in the macropores only. Thus the existence of a retardation effect in the overall gas transport is concluded. This retardation effect is primarily due to the micropore resistances, in particular gas adsorption, and is independent of the changes in the macropore volumes. It is shown that macroporosity of the coal matrix may change during gas transport due to combined effects of pressure and sorption-induced swelling or shrinkage of the coal. It is estimated that the macroporosity variation is non-uniform in space and time, as it is expected in reality, and typically taking values less than ±10 percent of the initial porosity.

Jan 1, 2009

By John S. Berber

To improve the economics of low-temperature carbonization of coal, the Bureau of Mines is conducting research on the upgrading of the product tar to marketable chemicals. This report describes experiments on the catalytic hydrodealkylation, followed by catalytic vapor-phase oxidation of the dealkylate to phthalic and maleic anhydrides, of mixed residues from the urea adduction of lignite-neutral oil fraction and on the catalytic thermal dealkylation of high-boiling tar acids. The hydrodealkylation experiments were conducted at pressures from 1,000 to 1,750 psig and at temperatures from 600° to 1,000° F. The oxidation was, in all cases, at atmospheric pressure and 9500 F. Maximum yield of maleic anhydride, based on the liquid feed to the hydrodealky1ation unit, was 12.2 percent at 750° F and 1,500 psig; that of phthalic anhydirde was 6.9 percent at 650° F and 1,500 psig. Maximum yield of combined anhydrides was 18.8 percent at 650° F and 1,500 psig. The non-dealkylated feed material, upon oxidation, yielded 8.9 percent and 3.8 percent maleic anhydride and phthalic anhydride, respectively.

Jan 1, 1967

By C. C. Popoff

The development of glass-making industries in the Pacific Northwest as well as other industries that use pure silica has been retarded by lack of local supplies of low-cost raw material. Several quartz deposits along the Skagit River constitute the only known source of relatively pure silica within the range of cheap transportation to the Seattle industrial area. Although some silica has been mined from these deposits, very little information regarding their size, grade, and other physical characteristics has been available to the general public. As a part of its program of investigation of the mineral resources of the Pacific Northwest, the Bureau of Mines assigned the writer to examine the Skagit River silica deposits in October 1946. This report presents the factual data obtained from an examination of the so-called Stoner, Bacon Creek, and Pressentin deposits. These deposits are the largest and most easily accessible known to exist in the area. The deposits are near Marblemount, which is on State Highway 17A. They are within 1 mile to 1-1/2 miles of the Skagit. River Railway, which provides transportation to Seattle, a distance of 130 miles. None of the deposits has been developed thoroughly. The Stoner deposit, however, has been developed by a quarry about, 5,0 feet square and has been exposed by hydraulic removal of the overburden throughout a distance of 180 feet along the hanging wall of the vein

Jan 1, 1949